From: Jagan Teki <jagan@amarulasolutions.com>
To: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
Sascha Hauer <kernel@pengutronix.de>,
Fabio Estevam <fabio.estevam@nxp.com>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Fabio maggi <fabio.mauri@bticino.it>,
lamiaposta71@gmail.com,
Andrea CORTESE <andrea.cortese@bticino.it>,
"davide . bonfanti" <davide.bonfanti@bticino.it>,
Shyam Saini <shyam.saini@amarulasolutions.com>,
Michael Trimarchi <michael@amarulasolutions.com>,
Jagan Teki <jagan@amarulasolutions.com>,
Simone CIANNI <simone.cianni@bticino.it>,
Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Subject: [PATCH v2 2/2] ARM: dts: i.MX6: Add BTicino i.MX6DL Mamoj initial support
Date: Tue, 20 Mar 2018 01:11:14 +0530 [thread overview]
Message-ID: <20180319194114.15349-2-jagan@amarulasolutions.com> (raw)
In-Reply-To: <20180319194114.15349-1-jagan@amarulasolutions.com>
This patch adds initial support for BTicino i.MX6DL Mamoj board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
---
Changes for v2:
- Squash 'PFUZE100 support' patch
- Remove fec PHY reset mux
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-mamoj.dts | 224 +++++++++++++++++++++++++++++++++++++
2 files changed, 225 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-mamoj.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 26e2e290ec28..b5dcc55bd157 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -397,6 +397,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-hummingboard2-som-v15.dtb \
imx6dl-icore.dtb \
imx6dl-icore-rqs.dtb \
+ imx6dl-mamoj.dtb \
imx6dl-nit6xlite.dtb \
imx6dl-nitrogen6x.dtb \
imx6dl-phytec-mira-rdk-nand.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-mamoj.dts b/arch/arm/boot/dts/imx6dl-mamoj.dts
new file mode 100644
index 000000000000..58b676922745
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-mamoj.dts
@@ -0,0 +1,224 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2018 BTicino
+ * Copyright (C) 2018 Amarula Solutions B.V.
+ */
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+
+/ {
+ model = "BTicino i.MX6DL Mamoj board";
+ compatible = "bticino,imx6dl-mamoj", "fsl,imx6dl";
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "mii";
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+};
+
+&i2c4 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ status = "okay";
+
+ pmic: pfuze100@8 {
+ compatible = "fsl,pfuze100";
+ reg = <0x08>;
+
+ regulators {
+ /* CPU vdd_arm core */
+ sw1a_reg: sw1ab {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ /* SOC vdd_soc */
+ sw1c_reg: sw1c {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ /* I/O power GEN_3V3 */
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* DDR memory */
+ sw3a_reg: sw3a {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* DDR memory */
+ sw3b_reg: sw3b {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* not used */
+ sw4_reg: sw4 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ /* not used */
+ swbst_reg: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ };
+
+ /* PMIC vsnvs. EX boot mode */
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* not used */
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ /* not used */
+ vgen2_reg: vgen2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ /* not used */
+ vgen3_reg: vgen3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ /* 1v8 general power */
+ vgen4_reg: vgen4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ /* 2v8 general power IMX6 */
+ vgen5_reg: vgen5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ /* 3v3 Ethernet */
+ vgen6_reg: vgen6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ bus-width = <8>;
+ non-removable;
+ keep-power-in-suspend;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b1
+ MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+ MX6QDL_PAD_KEY_ROW2__ENET_TX_DATA2 0x1b0b0
+ MX6QDL_PAD_KEY_ROW0__ENET_TX_DATA3 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_GPIO_19__ENET_TX_ER 0x1b0b0
+ MX6QDL_PAD_GPIO_18__ENET_RX_CLK 0x1b0b1
+ MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+ MX6QDL_PAD_KEY_COL2__ENET_RX_DATA2 0x1b0b0
+ MX6QDL_PAD_KEY_COL0__ENET_RX_DATA3 0x1b0b0
+ MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
+ MX6QDL_PAD_KEY_COL3__ENET_CRS 0x1b0b0
+ MX6QDL_PAD_KEY_ROW1__ENET_COL 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_7__I2C4_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_8__I2C4_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
+ >;
+ };
+};
--
2.14.3
next prev parent reply other threads:[~2018-03-19 19:41 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-03-19 19:41 [PATCH v2 1/2] dt-bindings: Add vendor prefix for Bticino Jagan Teki
2018-03-19 19:41 ` Jagan Teki [this message]
2018-03-20 15:35 ` [PATCH v2 2/2] ARM: dts: i.MX6: Add BTicino i.MX6DL Mamoj initial support Fabio Estevam
2018-04-16 7:24 ` Shawn Guo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180319194114.15349-2-jagan@amarulasolutions.com \
--to=jagan@amarulasolutions.com \
--cc=andrea.cortese@bticino.it \
--cc=davide.bonfanti@bticino.it \
--cc=devicetree@vger.kernel.org \
--cc=fabio.estevam@nxp.com \
--cc=fabio.mauri@bticino.it \
--cc=kernel@pengutronix.de \
--cc=lamiaposta71@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=michael@amarulasolutions.com \
--cc=raffaele.recalcati@bticino.it \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
--cc=shyam.saini@amarulasolutions.com \
--cc=simone.cianni@bticino.it \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).