From: Adam Ford <aford173@gmail.com>
To: adam.ford@logicpd.com
Cc: Adam Ford <aford173@gmail.com>, Sekhar Nori <nsekhar@ti.com>,
Kevin Hilman <khilman@kernel.org>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: [PATCH V3] ARM: dts: da850-evm: use phandles to extend nodes
Date: Mon, 7 May 2018 07:37:21 -0500 [thread overview]
Message-ID: <20180507123721.9264-1-aford173@gmail.com> (raw)
Many node labels in the device tree (like serial0, serial1, etc) are being
redefined, so let's modernize the device tree by using phandles to
extend the existing nodes. This helps reduce the whitespace.
Signed-off-by: Adam Ford <aford173@gmail.com>
---
V3: Rebase against 4.18/dt and fix subject.
V2: Rename subject per feedback from Sekhar.
Extend notes from tps6507x
Add empty line after each node
diff --git a/arch/arm/boot/dts/da850-evm.dts b/arch/arm/boot/dts/da850-evm.dts
index 339cae353302..3c486d8675b8 100644
--- a/arch/arm/boot/dts/da850-evm.dts
+++ b/arch/arm/boot/dts/da850-evm.dts
@@ -27,143 +27,6 @@
spi0 = &spi1;
};
- soc@1c00000 {
- pmx_core: pinmux@14120 {
- status = "okay";
-
- mcasp0_pins: pinmux_mcasp0_pins {
- pinctrl-single,bits = <
- /*
- * AHCLKX, ACLKX, AFSX, AHCLKR, ACLKR,
- * AFSR, AMUTE
- */
- 0x00 0x11111111 0xffffffff
- /* AXR11, AXR12 */
- 0x04 0x00011000 0x000ff000
- >;
- };
- nand_pins: nand_pins {
- pinctrl-single,bits = <
- /* EMA_WAIT[0], EMA_OE, EMA_WE, EMA_CS[4], EMA_CS[3] */
- 0x1c 0x10110110 0xf0ff0ff0
- /*
- * EMA_D[0], EMA_D[1], EMA_D[2],
- * EMA_D[3], EMA_D[4], EMA_D[5],
- * EMA_D[6], EMA_D[7]
- */
- 0x24 0x11111111 0xffffffff
- /* EMA_A[1], EMA_A[2] */
- 0x30 0x01100000 0x0ff00000
- >;
- };
- };
- serial0: serial@42000 {
- status = "okay";
- };
- serial1: serial@10c000 {
- status = "okay";
- };
- serial2: serial@10d000 {
- status = "okay";
- };
- rtc0: rtc@23000 {
- status = "okay";
- };
- i2c0: i2c@22000 {
- status = "okay";
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins>;
-
- tps: tps@48 {
- reg = <0x48>;
- };
- tlv320aic3106: tlv320aic3106@18 {
- #sound-dai-cells = <0>;
- compatible = "ti,tlv320aic3106";
- reg = <0x18>;
- status = "okay";
-
- /* Regulators */
- IOVDD-supply = <&vdcdc2_reg>;
- /* Derived from VBAT: Baseboard 3.3V / 1.8V */
- AVDD-supply = <&vbat>;
- DRVDD-supply = <&vbat>;
- DVDD-supply = <&vbat>;
- };
- tca6416: gpio@20 {
- compatible = "ti,tca6416";
- reg = <0x20>;
- gpio-controller;
- #gpio-cells = <2>;
- };
- };
- wdt: wdt@21000 {
- status = "okay";
- };
- mmc0: mmc@40000 {
- max-frequency = <50000000>;
- bus-width = <4>;
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins>;
- };
- spi1: spi@30e000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&spi1_pins &spi1_cs0_pin>;
- flash: m25p80@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "m25p64";
- spi-max-frequency = <30000000>;
- m25p,fast-read;
- reg = <0>;
- partition@0 {
- label = "U-Boot-SPL";
- reg = <0x00000000 0x00010000>;
- read-only;
- };
- partition@1 {
- label = "U-Boot";
- reg = <0x00010000 0x00080000>;
- read-only;
- };
- partition@2 {
- label = "U-Boot-Env";
- reg = <0x00090000 0x00010000>;
- read-only;
- };
- partition@3 {
- label = "Kernel";
- reg = <0x000a0000 0x00280000>;
- };
- partition@4 {
- label = "Filesystem";
- reg = <0x00320000 0x00400000>;
- };
- partition@5 {
- label = "MAC-Address";
- reg = <0x007f0000 0x00010000>;
- read-only;
- };
- };
- };
- mdio: mdio@224000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&mdio_pins>;
- bus_freq = <2200000>;
- };
- eth0: ethernet@220000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&mii_pins>;
- };
- gpio: gpio@226000 {
- status = "okay";
- };
- };
vbat: fixedregulator0 {
compatible = "regulator-fixed";
regulator-name = "vbat";
@@ -200,56 +63,200 @@
};
};
+&pmx_core {
+ status = "okay";
+
+ mcasp0_pins: pinmux_mcasp0_pins {
+ pinctrl-single,bits = <
+ /*
+ * AHCLKX, ACLKX, AFSX, AHCLKR, ACLKR,
+ * AFSR, AMUTE
+ */
+ 0x00 0x11111111 0xffffffff
+ /* AXR11, AXR12 */
+ 0x04 0x00011000 0x000ff000
+ >;
+ };
+ nand_pins: nand_pins {
+ pinctrl-single,bits = <
+ /* EMA_WAIT[0], EMA_OE, EMA_WE, EMA_CS[4], EMA_CS[3] */
+ 0x1c 0x10110110 0xf0ff0ff0
+ /*
+ * EMA_D[0], EMA_D[1], EMA_D[2],
+ * EMA_D[3], EMA_D[4], EMA_D[5],
+ * EMA_D[6], EMA_D[7]
+ */
+ 0x24 0x11111111 0xffffffff
+ /* EMA_A[1], EMA_A[2] */
+ 0x30 0x01100000 0x0ff00000
+ >;
+ };
+};
+
+&serial0 {
+ status = "okay";
+};
+
+&serial1 {
+ status = "okay";
+};
+
+&serial2 {
+ status = "okay";
+};
+
+&rtc0 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ tps: tps@48 {
+ reg = <0x48>;
+ };
+ tlv320aic3106: tlv320aic3106@18 {
+ #sound-dai-cells = <0>;
+ compatible = "ti,tlv320aic3106";
+ reg = <0x18>;
+ status = "okay";
+
+ /* Regulators */
+ IOVDD-supply = <&vdcdc2_reg>;
+ /* Derived from VBAT: Baseboard 3.3V / 1.8V */
+ AVDD-supply = <&vbat>;
+ DRVDD-supply = <&vbat>;
+ DVDD-supply = <&vbat>;
+ };
+ tca6416: gpio@20 {
+ compatible = "ti,tca6416";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+};
+
+&wdt {
+ status = "okay";
+};
+
+&mmc0 {
+ max-frequency = <50000000>;
+ bus-width = <4>;
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+};
+
+&spi1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_pins &spi1_cs0_pin>;
+ flash: m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p64";
+ spi-max-frequency = <30000000>;
+ m25p,fast-read;
+ reg = <0>;
+ partition@0 {
+ label = "U-Boot-SPL";
+ reg = <0x00000000 0x00010000>;
+ read-only;
+ };
+ partition@1 {
+ label = "U-Boot";
+ reg = <0x00010000 0x00080000>;
+ read-only;
+ };
+ partition@2 {
+ label = "U-Boot-Env";
+ reg = <0x00090000 0x00010000>;
+ read-only;
+ };
+ partition@3 {
+ label = "Kernel";
+ reg = <0x000a0000 0x00280000>;
+ };
+ partition@4 {
+ label = "Filesystem";
+ reg = <0x00320000 0x00400000>;
+ };
+ partition@5 {
+ label = "MAC-Address";
+ reg = <0x007f0000 0x00010000>;
+ read-only;
+ };
+ };
+};
+&mdio {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio_pins>;
+ bus_freq = <2200000>;
+};
+
+ð0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mii_pins>;
+};
+
+&gpio {
+ status = "okay";
+};
+
/include/ "tps6507x.dtsi"
&tps {
vdcdc1_2-supply = <&vbat>;
vdcdc3-supply = <&vbat>;
vldo1_2-supply = <&vbat>;
+};
- regulators {
- vdcdc1_reg: regulator@0 {
- regulator-name = "VDCDC1_3.3V";
- regulator-min-microvolt = <3150000>;
- regulator-max-microvolt = <3450000>;
- regulator-always-on;
- regulator-boot-on;
- };
+&vdcdc1_reg {
+ regulator-name = "VDCDC1_3.3V";
+ regulator-min-microvolt = <3150000>;
+ regulator-max-microvolt = <3450000>;
+ regulator-always-on;
+ regulator-boot-on;
+};
- vdcdc2_reg: regulator@1 {
- regulator-name = "VDCDC2_3.3V";
- regulator-min-microvolt = <1710000>;
- regulator-max-microvolt = <3450000>;
- regulator-always-on;
- regulator-boot-on;
- ti,defdcdc_default = <1>;
- };
+&vdcdc2_reg {
+ regulator-name = "VDCDC2_3.3V";
+ regulator-min-microvolt = <1710000>;
+ regulator-max-microvolt = <3450000>;
+ regulator-always-on;
+ regulator-boot-on;
+ ti,defdcdc_default = <1>;
+};
- vdcdc3_reg: regulator@2 {
- regulator-name = "VDCDC3_1.2V";
- regulator-min-microvolt = <950000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-boot-on;
- ti,defdcdc_default = <1>;
- };
+&vdcdc3_reg {
+ regulator-name = "VDCDC3_1.2V";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ ti,defdcdc_default = <1>;
+};
- ldo1_reg: regulator@3 {
- regulator-name = "LDO1_1.8V";
- regulator-min-microvolt = <1710000>;
- regulator-max-microvolt = <1890000>;
- regulator-always-on;
- regulator-boot-on;
- };
+&ldo1_reg {
+ regulator-name = "LDO1_1.8V";
+ regulator-min-microvolt = <1710000>;
+ regulator-max-microvolt = <1890000>;
+ regulator-always-on;
+ regulator-boot-on;
+};
- ldo2_reg: regulator@4 {
- regulator-name = "LDO2_1.2V";
- regulator-min-microvolt = <1140000>;
- regulator-max-microvolt = <1320000>;
- regulator-always-on;
- regulator-boot-on;
- };
- };
+&ldo2_reg {
+ regulator-name = "LDO2_1.2V";
+ regulator-min-microvolt = <1140000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-always-on;
+ regulator-boot-on;
};
&mcasp0 {
--
2.17.0
next reply other threads:[~2018-05-07 12:37 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-05-07 12:37 Adam Ford [this message]
2018-05-10 9:10 ` [PATCH V3] ARM: dts: da850-evm: use phandles to extend nodes Sekhar Nori
2018-05-10 15:08 ` Adam Ford
2018-05-10 15:19 ` Sekhar Nori
2018-05-10 15:39 ` Adam Ford
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180507123721.9264-1-aford173@gmail.com \
--to=aford173@gmail.com \
--cc=adam.ford@logicpd.com \
--cc=devicetree@vger.kernel.org \
--cc=khilman@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=nsekhar@ti.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).