* [PATCH v3 1/6] mfd: bd71837: mfd driver for ROHM BD71837 PMIC
2018-05-29 9:57 [PATCH v3 0/6] mfd/regulator/clk: bd71837: ROHM BD71837 PMIC driver Matti Vaittinen
@ 2018-05-29 9:58 ` Matti Vaittinen
2018-05-29 9:59 ` [PATCH v3 2/6] mfd: bd71837: Devicetree bindings " Matti Vaittinen
` (4 subsequent siblings)
5 siblings, 0 replies; 11+ messages in thread
From: Matti Vaittinen @ 2018-05-29 9:58 UTC (permalink / raw)
To: mturquette, sboyd, robh+dt, mark.rutland, lee.jones, lgirdwood,
broonie, mazziesaccount
Cc: linux-clk, devicetree, linux-kernel, mikko.mutanen,
heikki.haikola
ROHM BD71837 PMIC MFD driver providing interrupts and support
for two subsystems:
- clk
- Regulators
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---
drivers/mfd/Kconfig | 13 ++
drivers/mfd/Makefile | 1 +
drivers/mfd/bd71837.c | 224 ++++++++++++++++++++++++++++++++++
include/linux/mfd/bd71837.h | 288 ++++++++++++++++++++++++++++++++++++++++++++
4 files changed, 526 insertions(+)
create mode 100644 drivers/mfd/bd71837.c
create mode 100644 include/linux/mfd/bd71837.h
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index b860eb5aa194..7aa05fc9ed8e 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -1787,6 +1787,19 @@ config MFD_STW481X
in various ST Microelectronics and ST-Ericsson embedded
Nomadik series.
+config MFD_BD71837
+ bool "BD71837 Power Management chip"
+ depends on I2C=y
+ depends on OF
+ select REGMAP_I2C
+ select REGMAP_IRQ
+ select MFD_CORE
+ help
+ Select this option to get support for the ROHM BD71837
+ Power Management chips. BD71837 is designed to power processors like
+ NXP i.MX8. It contains 8 BUCK outputs and 7 LDOs, voltage monitoring
+ and emergency shut down as well as 32,768KHz clock output.
+
config MFD_STM32_LPTIMER
tristate "Support for STM32 Low-Power Timer"
depends on (ARCH_STM32 && OF) || COMPILE_TEST
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index e9fd20dba18d..09dc9eb3782c 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -227,4 +227,5 @@ obj-$(CONFIG_MFD_STM32_TIMERS) += stm32-timers.o
obj-$(CONFIG_MFD_MXS_LRADC) += mxs-lradc.o
obj-$(CONFIG_MFD_SC27XX_PMIC) += sprd-sc27xx-spi.o
obj-$(CONFIG_RAVE_SP_CORE) += rave-sp.o
+obj-$(CONFIG_MFD_BD71837) += bd71837.o
diff --git a/drivers/mfd/bd71837.c b/drivers/mfd/bd71837.c
new file mode 100644
index 000000000000..0200bbdbefa3
--- /dev/null
+++ b/drivers/mfd/bd71837.c
@@ -0,0 +1,224 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2018 ROHM Semiconductors */
+/*
+ * bd71837.c -- ROHM BD71837MWV mfd driver
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/gpio.h>
+#include <linux/regmap.h>
+#include <linux/of_device.h>
+#include <linux/of_gpio.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/bd71837.h>
+
+/* bd71837 multi function cells */
+static struct mfd_cell bd71837_mfd_cells[] = {
+ {
+ .name = "bd71837-clk",
+ .of_compatible = "rohm,bd71837-clk",
+ }, {
+ .name = "bd71837-pmic",
+ },
+};
+
+static const struct regmap_irq bd71837_irqs[] = {
+ REGMAP_IRQ_REG(BD71837_INT_SWRST, 0, BD71837_INT_SWRST_MASK),
+ REGMAP_IRQ_REG(BD71837_INT_PWRBTN_S, 0, BD71837_INT_PWRBTN_S_MASK),
+ REGMAP_IRQ_REG(BD71837_INT_PWRBTN_L, 0, BD71837_INT_PWRBTN_L_MASK),
+ REGMAP_IRQ_REG(BD71837_INT_PWRBTN, 0, BD71837_INT_PWRBTN_MASK),
+ REGMAP_IRQ_REG(BD71837_INT_WDOG, 0, BD71837_INT_WDOG_MASK),
+ REGMAP_IRQ_REG(BD71837_INT_ON_REQ, 0, BD71837_INT_ON_REQ_MASK),
+ REGMAP_IRQ_REG(BD71837_INT_STBY_REQ, 0, BD71837_INT_STBY_REQ_MASK),
+};
+
+static struct regmap_irq_chip bd71837_irq_chip = {
+ .name = "bd71837-irq",
+ .irqs = bd71837_irqs,
+ .num_irqs = ARRAY_SIZE(bd71837_irqs),
+ .num_regs = 1,
+ .irq_reg_stride = 1,
+ .status_base = BD71837_REG_IRQ,
+ .mask_base = BD71837_REG_MIRQ,
+ .mask_invert = false,
+};
+
+static int bd71837_irq_exit(struct bd71837 *bd71837)
+{
+ if (bd71837->chip_irq > 0)
+ regmap_del_irq_chip(bd71837->chip_irq, bd71837->irq_data);
+ return 0;
+}
+
+static const struct regmap_range pmic_status_range = {
+ .range_min = BD71837_REG_IRQ,
+ .range_max = BD71837_REG_POW_STATE,
+};
+
+static const struct regmap_access_table volatile_regs = {
+ .yes_ranges = &pmic_status_range,
+ .n_yes_ranges = 1,
+};
+
+static const struct regmap_config bd71837_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .volatile_table = &volatile_regs,
+ .max_register = BD71837_MAX_REGISTER - 1,
+ .cache_type = REGCACHE_RBTREE,
+};
+
+#ifdef CONFIG_OF
+static const struct of_device_id bd71837_of_match[] = {
+ { .compatible = "rohm,bd71837", .data = (void *)0},
+ { },
+};
+MODULE_DEVICE_TABLE(of, bd71837_of_match);
+
+static int bd71837_parse_dt(struct i2c_client *client, struct bd71837_board **b)
+{
+ struct device_node *np = client->dev.of_node;
+ struct bd71837_board *board_info;
+ unsigned int prop;
+ int r;
+ int rv = -ENOMEM;
+
+ board_info = devm_kzalloc(&client->dev, sizeof(*board_info),
+ GFP_KERNEL);
+ if (!board_info)
+ goto err_out;
+
+ if (client->irq) {
+ dev_dbg(&client->dev, "Got irq %d\n", client->irq);
+ board_info->gpio_intr = client->irq;
+ } else {
+ dev_err(&client->dev, "no pmic intr pin available\n");
+ rv = -ENOENT;
+ goto err_intr;
+ }
+ r = of_property_read_u32(np, "irq_base", &prop);
+ if (!r)
+ board_info->irq_base = prop;
+ else
+ board_info->irq_base = 0;
+
+ rv = 0;
+ *b = board_info;
+ if (0) {
+err_intr:
+ devm_kfree(&client->dev, board_info);
+err_out:
+ dev_err(&client->dev, "failed to parse device-tree (%d)\n", rv);
+ }
+ return rv;
+}
+#endif //CONFIG_OF
+
+static int bd71837_i2c_probe(struct i2c_client *i2c,
+ const struct i2c_device_id *id)
+{
+ struct bd71837 *bd71837;
+ struct bd71837_board *pmic_plat_data;
+ int ret = -EINVAL;
+
+ pmic_plat_data = dev_get_platdata(&i2c->dev);
+
+ if (!pmic_plat_data && i2c->dev.of_node)
+ ret = bd71837_parse_dt(i2c, &pmic_plat_data);
+
+ if (!pmic_plat_data)
+ return ret;
+
+ bd71837 = devm_kzalloc(&i2c->dev, sizeof(struct bd71837), GFP_KERNEL);
+ if (bd71837 == NULL)
+ return -ENOMEM;
+
+ bd71837->of_plat_data = pmic_plat_data;
+ i2c_set_clientdata(i2c, bd71837);
+ bd71837->dev = &i2c->dev;
+ bd71837->i2c_client = i2c;
+ bd71837->chip_irq = pmic_plat_data->gpio_intr;
+
+ bd71837->regmap = devm_regmap_init_i2c(i2c, &bd71837_regmap_config);
+ if (IS_ERR(bd71837->regmap)) {
+ ret = PTR_ERR(bd71837->regmap);
+ dev_err(&i2c->dev, "regmap initialization failed: %d\n", ret);
+ goto err_out;
+ }
+
+ ret = bd71837_reg_read(bd71837, BD71837_REG_REV);
+ if (ret < 0) {
+ dev_err(bd71837->dev,
+ "%s(): Read BD71837_REG_DEVICE failed!\n", __func__);
+ goto err_out;
+ }
+
+ ret = regmap_add_irq_chip(bd71837->regmap, bd71837->chip_irq,
+ IRQF_ONESHOT, 0,
+ &bd71837_irq_chip, &bd71837->irq_data);
+ if (ret < 0) {
+ dev_err(bd71837->dev, "Failed to add irq_chip %d\n", ret);
+ goto err_out;
+ }
+
+ ret = mfd_add_devices(bd71837->dev, PLATFORM_DEVID_AUTO,
+ bd71837_mfd_cells, ARRAY_SIZE(bd71837_mfd_cells),
+ NULL, 0,
+ regmap_irq_get_domain(bd71837->irq_data));
+ if (ret)
+ regmap_del_irq_chip(bd71837->chip_irq, bd71837->irq_data);
+err_out:
+
+ return ret;
+}
+
+static int bd71837_i2c_remove(struct i2c_client *i2c)
+{
+ struct bd71837 *bd71837 = i2c_get_clientdata(i2c);
+
+ bd71837_irq_exit(bd71837);
+ mfd_remove_devices(bd71837->dev);
+
+ return 0;
+}
+
+static const struct i2c_device_id bd71837_i2c_id[] = {
+ { .name = "bd71837", },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, bd71837_i2c_id);
+
+static struct i2c_driver bd71837_i2c_driver = {
+ .driver = {
+ .name = "bd71837-mfd",
+ .owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(bd71837_of_match),
+ },
+ .probe = bd71837_i2c_probe,
+ .remove = bd71837_i2c_remove,
+ .id_table = bd71837_i2c_id,
+};
+
+static int __init bd71837_i2c_init(void)
+{
+ return i2c_add_driver(&bd71837_i2c_driver);
+}
+/* init early so consumer devices can complete system boot */
+subsys_initcall(bd71837_i2c_init);
+
+static void __exit bd71837_i2c_exit(void)
+{
+ i2c_del_driver(&bd71837_i2c_driver);
+}
+module_exit(bd71837_i2c_exit);
+
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
+MODULE_DESCRIPTION("BD71837 chip multi-function driver");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/mfd/bd71837.h b/include/linux/mfd/bd71837.h
new file mode 100644
index 000000000000..4475914fa3a9
--- /dev/null
+++ b/include/linux/mfd/bd71837.h
@@ -0,0 +1,288 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2018 ROHM Semiconductors */
+
+/*
+ * ROHM BD71837MWV header file
+ */
+
+#ifndef __LINUX_MFD_BD71837_H__
+#define __LINUX_MFD_BD71837_H__
+
+#include <linux/regmap.h>
+
+enum {
+ BD71837_BUCK1 = 0,
+ BD71837_BUCK2,
+ BD71837_BUCK3,
+ BD71837_BUCK4,
+ BD71837_BUCK5,
+ BD71837_BUCK6,
+ BD71837_BUCK7,
+ BD71837_BUCK8,
+ BD71837_LDO1,
+ BD71837_LDO2,
+ BD71837_LDO3,
+ BD71837_LDO4,
+ BD71837_LDO5,
+ BD71837_LDO6,
+ BD71837_LDO7,
+ BD71837_REGULATOR_CNT,
+};
+
+#define BD71837_BUCK1_VOLTAGE_NUM 0x40
+#define BD71837_BUCK2_VOLTAGE_NUM 0x40
+#define BD71837_BUCK3_VOLTAGE_NUM 0x40
+#define BD71837_BUCK4_VOLTAGE_NUM 0x40
+
+#define BD71837_BUCK5_VOLTAGE_NUM 0x08
+#define BD71837_BUCK6_VOLTAGE_NUM 0x04
+#define BD71837_BUCK7_VOLTAGE_NUM 0x08
+#define BD71837_BUCK8_VOLTAGE_NUM 0x40
+
+#define BD71837_LDO1_VOLTAGE_NUM 0x04
+#define BD71837_LDO2_VOLTAGE_NUM 0x02
+#define BD71837_LDO3_VOLTAGE_NUM 0x10
+#define BD71837_LDO4_VOLTAGE_NUM 0x10
+#define BD71837_LDO5_VOLTAGE_NUM 0x10
+#define BD71837_LDO6_VOLTAGE_NUM 0x10
+#define BD71837_LDO7_VOLTAGE_NUM 0x10
+
+enum {
+ BD71837_REG_REV = 0x00,
+ BD71837_REG_SWRESET = 0x01,
+ BD71837_REG_I2C_DEV = 0x02,
+ BD71837_REG_PWRCTRL0 = 0x03,
+ BD71837_REG_PWRCTRL1 = 0x04,
+ BD71837_REG_BUCK1_CTRL = 0x05,
+ BD71837_REG_BUCK2_CTRL = 0x06,
+ BD71837_REG_BUCK3_CTRL = 0x07,
+ BD71837_REG_BUCK4_CTRL = 0x08,
+ BD71837_REG_BUCK5_CTRL = 0x09,
+ BD71837_REG_BUCK6_CTRL = 0x0A,
+ BD71837_REG_BUCK7_CTRL = 0x0B,
+ BD71837_REG_BUCK8_CTRL = 0x0C,
+ BD71837_REG_BUCK1_VOLT_RUN = 0x0D,
+ BD71837_REG_BUCK1_VOLT_IDLE = 0x0E,
+ BD71837_REG_BUCK1_VOLT_SUSP = 0x0F,
+ BD71837_REG_BUCK2_VOLT_RUN = 0x10,
+ BD71837_REG_BUCK2_VOLT_IDLE = 0x11,
+ BD71837_REG_BUCK3_VOLT_RUN = 0x12,
+ BD71837_REG_BUCK4_VOLT_RUN = 0x13,
+ BD71837_REG_BUCK5_VOLT = 0x14,
+ BD71837_REG_BUCK6_VOLT = 0x15,
+ BD71837_REG_BUCK7_VOLT = 0x16,
+ BD71837_REG_BUCK8_VOLT = 0x17,
+ BD71837_REG_LDO1_VOLT = 0x18,
+ BD71837_REG_LDO2_VOLT = 0x19,
+ BD71837_REG_LDO3_VOLT = 0x1A,
+ BD71837_REG_LDO4_VOLT = 0x1B,
+ BD71837_REG_LDO5_VOLT = 0x1C,
+ BD71837_REG_LDO6_VOLT = 0x1D,
+ BD71837_REG_LDO7_VOLT = 0x1E,
+ BD71837_REG_TRANS_COND0 = 0x1F,
+ BD71837_REG_TRANS_COND1 = 0x20,
+ BD71837_REG_VRFAULTEN = 0x21,
+ BD71837_REG_MVRFLTMASK0 = 0x22,
+ BD71837_REG_MVRFLTMASK1 = 0x23,
+ BD71837_REG_MVRFLTMASK2 = 0x24,
+ BD71837_REG_RCVCFG = 0x25,
+ BD71837_REG_RCVNUM = 0x26,
+ BD71837_REG_PWRONCONFIG0 = 0x27,
+ BD71837_REG_PWRONCONFIG1 = 0x28,
+ BD71837_REG_RESETSRC = 0x29,
+ BD71837_REG_MIRQ = 0x2A,
+ BD71837_REG_IRQ = 0x2B,
+ BD71837_REG_IN_MON = 0x2C,
+ BD71837_REG_POW_STATE = 0x2D,
+ BD71837_REG_OUT32K = 0x2E,
+ BD71837_REG_REGLOCK = 0x2F,
+ BD71837_REG_OTPVER = 0xFF,
+ BD71837_MAX_REGISTER = 0x100,
+};
+
+#define REGLOCK_PWRSEQ 0x1
+#define REGLOCK_VREG 0x10
+
+/* Generic BUCK control masks */
+#define BD71837_BUCK_SEL 0x02
+#define BD71837_BUCK_EN 0x01
+#define BD71837_BUCK_RUN_ON 0x04
+
+/* Generic LDO masks */
+#define BD71837_LDO_SEL 0x80
+#define BD71837_LDO_EN 0x40
+
+/* BD71837 BUCK ramp rate CTRL reg bits */
+#define BUCK_RAMPRATE_MASK 0xC0
+#define BUCK_RAMPRATE_10P00MV 0x0
+#define BUCK_RAMPRATE_5P00MV 0x1
+#define BUCK_RAMPRATE_2P50MV 0x2
+#define BUCK_RAMPRATE_1P25MV 0x3
+
+/* BD71837_REG_BUCK1_VOLT_RUN bits */
+#define BUCK1_RUN_MASK 0x3F
+#define BUCK1_RUN_DEFAULT 0x14
+
+/* BD71837_REG_BUCK1_VOLT_SUSP bits */
+#define BUCK1_SUSP_MASK 0x3F
+#define BUCK1_SUSP_DEFAULT 0x14
+
+/* BD71837_REG_BUCK1_VOLT_IDLE bits */
+#define BUCK1_IDLE_MASK 0x3F
+#define BUCK1_IDLE_DEFAULT 0x14
+
+/* BD71837_REG_BUCK2_VOLT_RUN bits */
+#define BUCK2_RUN_MASK 0x3F
+#define BUCK2_RUN_DEFAULT 0x1E
+
+/* BD71837_REG_BUCK2_VOLT_IDLE bits */
+#define BUCK2_IDLE_MASK 0x3F
+#define BUCK2_IDLE_DEFAULT 0x14
+
+/* BD71837_REG_BUCK3_VOLT_RUN bits */
+#define BUCK3_RUN_MASK 0x3F
+#define BUCK3_RUN_DEFAULT 0x1E
+
+/* BD71837_REG_BUCK4_VOLT_RUN bits */
+#define BUCK4_RUN_MASK 0x3F
+#define BUCK4_RUN_DEFAULT 0x1E
+
+/* BD71837_REG_BUCK5_VOLT bits */
+#define BUCK5_MASK 0x07
+#define BUCK5_DEFAULT 0x02
+
+/* BD71837_REG_BUCK6_VOLT bits */
+#define BUCK6_MASK 0x03
+#define BUCK6_DEFAULT 0x03
+
+/* BD71837_REG_BUCK7_VOLT bits */
+#define BUCK7_MASK 0x07
+#define BUCK7_DEFAULT 0x03
+
+/* BD71837_REG_BUCK8_VOLT bits */
+#define BUCK8_MASK 0x3F
+#define BUCK8_DEFAULT 0x1E
+
+/* BD71837_REG_IRQ bits */
+#define IRQ_SWRST 0x40
+#define IRQ_PWRON_S 0x20
+#define IRQ_PWRON_L 0x10
+#define IRQ_PWRON 0x08
+#define IRQ_WDOG 0x04
+#define IRQ_ON_REQ 0x02
+#define IRQ_STBY_REQ 0x01
+
+/* BD71837_REG_OUT32K bits */
+#define BD71837_OUT32K_EN 0x01
+
+/* BD71837 gated clock rate */
+#define BD71837_CLK_RATE 32768
+
+/* BD71837 irqs */
+enum {
+ BD71837_INT_STBY_REQ,
+ BD71837_INT_ON_REQ,
+ BD71837_INT_WDOG,
+ BD71837_INT_PWRBTN,
+ BD71837_INT_PWRBTN_L,
+ BD71837_INT_PWRBTN_S,
+ BD71837_INT_SWRST
+};
+
+/* BD71837 interrupt masks */
+#define BD71837_INT_SWRST_MASK 0x40
+#define BD71837_INT_PWRBTN_S_MASK 0x20
+#define BD71837_INT_PWRBTN_L_MASK 0x10
+#define BD71837_INT_PWRBTN_MASK 0x8
+#define BD71837_INT_WDOG_MASK 0x4
+#define BD71837_INT_ON_REQ_MASK 0x2
+#define BD71837_INT_STBY_REQ_MASK 0x1
+
+/* BD71837_REG_LDO1_VOLT bits */
+#define LDO1_MASK 0x03
+
+/* BD71837_REG_LDO1_VOLT bits */
+#define LDO2_MASK 0x20
+
+/* BD71837_REG_LDO3_VOLT bits */
+#define LDO3_MASK 0x0F
+
+/* BD71837_REG_LDO4_VOLT bits */
+#define LDO4_MASK 0x0F
+
+/* BD71837_REG_LDO5_VOLT bits */
+#define LDO5_MASK 0x0F
+
+/* BD71837_REG_LDO6_VOLT bits */
+#define LDO6_MASK 0x0F
+
+/* BD71837_REG_LDO7_VOLT bits */
+#define LDO7_MASK 0x0F
+
+struct bd71837;
+struct bd71837_pmic;
+struct bd71837_clk;
+
+/*
+ * Board platform data may be used to initialize regulators.
+ */
+
+struct bd71837_board {
+ struct regulator_init_data *init_data[BD71837_REGULATOR_CNT];
+ int gpio_intr;
+ int irq_base;
+};
+
+struct bd71837 {
+ struct device *dev;
+ struct i2c_client *i2c_client;
+ struct regmap *regmap;
+ unsigned long int id;
+
+ int chip_irq;
+ struct regmap_irq_chip_data *irq_data;
+
+ struct bd71837_pmic *pmic;
+ struct bd71837_clk *clk;
+
+ struct bd71837_board *of_plat_data;
+};
+
+/*
+ * bd71837 sub-driver chip access routines
+ */
+
+static inline int bd71837_reg_read(struct bd71837 *bd71837, u8 reg)
+{
+ int r, val;
+
+ r = regmap_read(bd71837->regmap, reg, &val);
+ if (r < 0)
+ return r;
+ return val;
+}
+
+static inline int bd71837_reg_write(struct bd71837 *bd71837, u8 reg,
+ unsigned int val)
+{
+ return regmap_write(bd71837->regmap, reg, val);
+}
+
+static inline int bd71837_set_bits(struct bd71837 *bd71837, u8 reg, u8 mask)
+{
+ return regmap_update_bits(bd71837->regmap, reg, mask, mask);
+}
+
+static inline int bd71837_clear_bits(struct bd71837 *bd71837, u8 reg,
+ u8 mask)
+{
+ return regmap_update_bits(bd71837->regmap, reg, mask, 0);
+}
+
+static inline int bd71837_update_bits(struct bd71837 *bd71837, u8 reg,
+ u8 mask, u8 val)
+{
+ return regmap_update_bits(bd71837->regmap, reg, mask, val);
+}
+
+#endif /* __LINUX_MFD_BD71837_H__ */
--
2.14.3
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH v3 6/6] regulator: bd71837: BD71837 PMIC regulator driver
2018-05-29 9:57 [PATCH v3 0/6] mfd/regulator/clk: bd71837: ROHM BD71837 PMIC driver Matti Vaittinen
` (4 preceding siblings ...)
2018-05-29 10:01 ` [PATCH v3 5/6] clk: bd71837: Add driver for BD71837 PMIC clock Matti Vaittinen
@ 2018-05-29 10:02 ` Matti Vaittinen
2018-05-29 11:47 ` Mark Brown
2018-06-05 13:58 ` Andy Shevchenko
5 siblings, 2 replies; 11+ messages in thread
From: Matti Vaittinen @ 2018-05-29 10:02 UTC (permalink / raw)
To: mturquette, sboyd, robh+dt, mark.rutland, lee.jones, lgirdwood,
broonie, mazziesaccount
Cc: linux-clk, devicetree, linux-kernel, mikko.mutanen,
heikki.haikola
Support for controlling the 8 bucks and 7 LDOs the PMIC contains.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---
drivers/regulator/Kconfig | 11 +
drivers/regulator/Makefile | 1 +
drivers/regulator/bd71837-regulator.c | 677 ++++++++++++++++++++++++++++++++++
3 files changed, 689 insertions(+)
create mode 100644 drivers/regulator/bd71837-regulator.c
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 097f61784a7d..139f4b53fea0 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -180,6 +180,17 @@ config REGULATOR_BCM590XX
BCM590xx PMUs. This will enable support for the software
controllable LDO/Switching regulators.
+config REGULATOR_BD71837
+ tristate "ROHM BD71837 Power Regulator"
+ depends on MFD_BD71837
+ help
+ This driver supports voltage regulators on ROHM BD71837 PMIC.
+ This will enable support for the software controllable buck
+ and LDO regulators.
+
+ This driver can also be built as a module. If so, the module
+ will be called bd71837-regulator.
+
config REGULATOR_BD9571MWV
tristate "ROHM BD9571MWV Regulators"
depends on MFD_BD9571MWV
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 590674fbecd7..1b4d8ec416c2 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -27,6 +27,7 @@ obj-$(CONFIG_REGULATOR_AS3711) += as3711-regulator.o
obj-$(CONFIG_REGULATOR_AS3722) += as3722-regulator.o
obj-$(CONFIG_REGULATOR_AXP20X) += axp20x-regulator.o
obj-$(CONFIG_REGULATOR_BCM590XX) += bcm590xx-regulator.o
+obj-$(CONFIG_REGULATOR_BD71837) += bd71837-regulator.o
obj-$(CONFIG_REGULATOR_BD9571MWV) += bd9571mwv-regulator.o
obj-$(CONFIG_REGULATOR_DA903X) += da903x.o
obj-$(CONFIG_REGULATOR_DA9052) += da9052-regulator.o
diff --git a/drivers/regulator/bd71837-regulator.c b/drivers/regulator/bd71837-regulator.c
new file mode 100644
index 000000000000..826c1ce3c6d6
--- /dev/null
+++ b/drivers/regulator/bd71837-regulator.c
@@ -0,0 +1,677 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2018 ROHM Semiconductors */
+/*
+ * bd71837-regulator.c ROHM BD71837MWV regulator driver
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/gpio.h>
+#include <linux/mfd/bd71837.h>
+#include <linux/regulator/of_regulator.h>
+
+struct bd71837_pmic {
+ struct regulator_desc descs[BD71837_REGULATOR_CNT];
+ struct bd71837 *mfd;
+ struct platform_device *pdev;
+ struct regulator_dev *rdev[BD71837_REGULATOR_CNT];
+ struct mutex mtx;
+};
+
+/*
+ * BUCK1/2/3/4
+ * BUCK1RAMPRATE[1:0] BUCK1 DVS ramp rate setting
+ * 00: 10.00mV/usec 10mV 1uS
+ * 01: 5.00mV/usec 10mV 2uS
+ * 10: 2.50mV/usec 10mV 4uS
+ * 11: 1.25mV/usec 10mV 8uS
+ */
+static int bd71837_buck1234_set_ramp_delay(struct regulator_dev *rdev,
+ int ramp_delay)
+{
+ struct bd71837_pmic *pmic = rdev_get_drvdata(rdev);
+ struct bd71837 *mfd = pmic->mfd;
+ int id = rdev->desc->id;
+ unsigned int ramp_value = BUCK_RAMPRATE_10P00MV;
+
+ dev_dbg(&(pmic->pdev->dev), "Buck[%d] Set Ramp = %d\n", id + 1,
+ ramp_delay);
+ switch (ramp_delay) {
+ case 1 ... 1250:
+ ramp_value = BUCK_RAMPRATE_1P25MV;
+ break;
+ case 1251 ... 2500:
+ ramp_value = BUCK_RAMPRATE_2P50MV;
+ break;
+ case 2501 ... 5000:
+ ramp_value = BUCK_RAMPRATE_5P00MV;
+ break;
+ case 5001 ... 10000:
+ ramp_value = BUCK_RAMPRATE_10P00MV;
+ break;
+ default:
+ ramp_value = BUCK_RAMPRATE_10P00MV;
+ dev_err(&pmic->pdev->dev,
+ "%s: ramp_delay: %d not supported, setting 10000mV//us\n",
+ rdev->desc->name, ramp_delay);
+ }
+
+ return regmap_update_bits(mfd->regmap, BD71837_REG_BUCK1_CTRL + id,
+ BUCK_RAMPRATE_MASK, ramp_value << 6);
+}
+
+static int bd71837_regulator_set_regmap(struct regulator_dev *rdev, int set)
+{
+ int ret = -EINVAL;
+ struct bd71837_pmic *pmic = rdev->reg_data;
+
+ /* According to the data sheet we must not change regulator voltage
+ * when it is enabled. Thus we need to check if regulator is enabled
+ * before changing the voltage. This mutex is used to avoid race where
+ * we might enable regulator after it's state has been checked but
+ * before the voltage is changed
+ */
+ mutex_lock(&pmic->mtx);
+ if (!set)
+ ret = regulator_disable_regmap(rdev);
+ else
+ ret = regulator_enable_regmap(rdev);
+ mutex_unlock(&pmic->mtx);
+
+ return ret;
+}
+
+static int bd71837_regulator_enable_regmap(struct regulator_dev *rdev)
+{
+ return bd71837_regulator_set_regmap(rdev, 1);
+}
+
+static int bd71837_regulator_disable_regmap(struct regulator_dev *rdev)
+{
+ return bd71837_regulator_set_regmap(rdev, 0);
+}
+
+static int bd71837_regulator_set_voltage_sel_regmap(struct regulator_dev *rdev,
+ unsigned int sel)
+{
+ int ret;
+ struct bd71837_pmic *pmic = rdev->reg_data;
+
+ /* According to the data sheet we must not change regulator voltage
+ * when it is enabled. Error out if regulator is enabled.
+ */
+ mutex_lock(&pmic->mtx);
+ ret = regulator_is_enabled_regmap(rdev);
+ if (!ret)
+ ret = regulator_set_voltage_sel_regmap(rdev, sel);
+ else if (ret == 1)
+ ret = -EBUSY;
+ mutex_unlock(&pmic->mtx);
+ return ret;
+}
+
+static struct regulator_ops bd71837_ldo_regulator_ops = {
+ .enable = bd71837_regulator_enable_regmap,
+ .disable = bd71837_regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_linear_range,
+ .set_voltage_sel = bd71837_regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+};
+
+static struct regulator_ops bd71837_ldo_regulator_nolinear_ops = {
+ .enable = bd71837_regulator_enable_regmap,
+ .disable = bd71837_regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_table,
+ .set_voltage_sel = bd71837_regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+};
+
+static struct regulator_ops bd71837_buck_regulator_ops = {
+ .enable = bd71837_regulator_enable_regmap,
+ .disable = bd71837_regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_linear_range,
+ .set_voltage_sel = bd71837_regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+};
+
+static struct regulator_ops bd71837_buck_regulator_nolinear_ops = {
+ .enable = bd71837_regulator_enable_regmap,
+ .disable = bd71837_regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_table,
+ .set_voltage_sel = bd71837_regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+};
+
+static struct regulator_ops bd71837_buck1234_regulator_ops = {
+ .enable = bd71837_regulator_enable_regmap,
+ .disable = bd71837_regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_linear_range,
+ .set_voltage_sel = bd71837_regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+ .set_ramp_delay = bd71837_buck1234_set_ramp_delay,
+};
+
+/*
+ * BUCK1/2/3/4
+ * 0.70 to 1.30V (10mV step)
+ */
+static const struct regulator_linear_range bd71837_buck1234_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(700000, 0x00, 0x3C, 10000),
+ REGULATOR_LINEAR_RANGE(1300000, 0x3D, 0x3F, 0),
+};
+
+/*
+ * BUCK5
+ * 0.9V to 1.35V ()
+ */
+static const struct regulator_linear_range bd71837_buck5_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(700000, 0x00, 0x03, 100000),
+ REGULATOR_LINEAR_RANGE(1050000, 0x04, 0x05, 50000),
+ REGULATOR_LINEAR_RANGE(1200000, 0x06, 0x07, 150000),
+};
+
+/*
+ * BUCK6
+ * 3.0V to 3.3V (step 100mV)
+ */
+static const struct regulator_linear_range bd71837_buck6_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(3000000, 0x00, 0x03, 100000),
+};
+
+/*
+ * BUCK7
+ * 000 = 1.605V
+ * 001 = 1.695V
+ * 010 = 1.755V
+ * 011 = 1.8V (Initial)
+ * 100 = 1.845V
+ * 101 = 1.905V
+ * 110 = 1.95V
+ * 111 = 1.995V
+ */
+static const unsigned int buck_7_volts[] = {
+ 1605000, 1695000, 1755000, 1800000, 1845000, 1905000, 1950000, 1995000
+};
+
+/*
+ * BUCK8
+ * 0.8V to 1.40V (step 10mV)
+ */
+static const struct regulator_linear_range bd71837_buck8_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(800000, 0x00, 0x3C, 10000),
+ REGULATOR_LINEAR_RANGE(1400000, 0x3D, 0x3F, 0),
+};
+
+/*
+ * LDO1
+ * 3.0 to 3.3V (100mV step)
+ */
+static const struct regulator_linear_range bd71837_ldo1_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(3000000, 0x00, 0x03, 100000),
+};
+
+/*
+ * LDO2
+ * 0.8 or 0.9V
+ */
+const unsigned int ldo_2_volts[] = {
+ 900000, 800000
+};
+
+/*
+ * LDO3
+ * 1.8 to 3.3V (100mV step)
+ */
+static const struct regulator_linear_range bd71837_ldo3_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
+};
+
+/*
+ * LDO4
+ * 0.9 to 1.8V (100mV step)
+ */
+static const struct regulator_linear_range bd71837_ldo4_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(900000, 0x00, 0x09, 100000),
+ REGULATOR_LINEAR_RANGE(1800000, 0x0A, 0x0F, 0),
+};
+
+/*
+ * LDO5
+ * 1.8 to 3.3V (100mV step)
+ */
+static const struct regulator_linear_range bd71837_ldo5_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
+};
+
+/*
+ * LDO6
+ * 0.9 to 1.8V (100mV step)
+ */
+static const struct regulator_linear_range bd71837_ldo6_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(900000, 0x00, 0x09, 100000),
+ REGULATOR_LINEAR_RANGE(1800000, 0x0A, 0x0F, 0),
+};
+
+/*
+ * LDO7
+ * 1.8 to 3.3V (100mV step)
+ */
+static const struct regulator_linear_range bd71837_ldo7_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
+};
+
+static const struct regulator_desc bd71837_regulators[] = {
+ {
+ .name = "buck1",
+ .of_match = of_match_ptr("BUCK1"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_BUCK1,
+ .ops = &bd71837_buck1234_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = BD71837_BUCK1_VOLTAGE_NUM,
+ .linear_ranges = bd71837_buck1234_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(bd71837_buck1234_voltage_ranges),
+ .vsel_reg = BD71837_REG_BUCK1_VOLT_RUN,
+ .vsel_mask = BUCK1_RUN_MASK,
+ .enable_reg = BD71837_REG_BUCK1_CTRL,
+ .enable_mask = BD71837_BUCK_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "buck2",
+ .of_match = of_match_ptr("BUCK2"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_BUCK2,
+ .ops = &bd71837_buck1234_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = BD71837_BUCK2_VOLTAGE_NUM,
+ .linear_ranges = bd71837_buck1234_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(bd71837_buck1234_voltage_ranges),
+ .vsel_reg = BD71837_REG_BUCK2_VOLT_RUN,
+ .vsel_mask = BUCK2_RUN_MASK,
+ .enable_reg = BD71837_REG_BUCK2_CTRL,
+ .enable_mask = BD71837_BUCK_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "buck3",
+ .of_match = of_match_ptr("BUCK3"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_BUCK3,
+ .ops = &bd71837_buck1234_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = BD71837_BUCK3_VOLTAGE_NUM,
+ .linear_ranges = bd71837_buck1234_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(bd71837_buck1234_voltage_ranges),
+ .vsel_reg = BD71837_REG_BUCK3_VOLT_RUN,
+ .vsel_mask = BUCK3_RUN_MASK,
+ .enable_reg = BD71837_REG_BUCK3_CTRL,
+ .enable_mask = BD71837_BUCK_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "buck4",
+ .of_match = of_match_ptr("BUCK4"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_BUCK4,
+ .ops = &bd71837_buck1234_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = BD71837_BUCK4_VOLTAGE_NUM,
+ .linear_ranges = bd71837_buck1234_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(bd71837_buck1234_voltage_ranges),
+ .vsel_reg = BD71837_REG_BUCK4_VOLT_RUN,
+ .vsel_mask = BUCK4_RUN_MASK,
+ .enable_reg = BD71837_REG_BUCK4_CTRL,
+ .enable_mask = BD71837_BUCK_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "buck5",
+ .of_match = of_match_ptr("BUCK5"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_BUCK5,
+ .ops = &bd71837_buck_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = BD71837_BUCK5_VOLTAGE_NUM,
+ .linear_ranges = bd71837_buck5_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(bd71837_buck5_voltage_ranges),
+ .vsel_reg = BD71837_REG_BUCK5_VOLT,
+ .vsel_mask = BUCK5_MASK,
+ .enable_reg = BD71837_REG_BUCK5_CTRL,
+ .enable_mask = BD71837_BUCK_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "buck6",
+ .of_match = of_match_ptr("BUCK6"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_BUCK6,
+ .ops = &bd71837_buck_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = BD71837_BUCK6_VOLTAGE_NUM,
+ .linear_ranges = bd71837_buck6_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(bd71837_buck6_voltage_ranges),
+ .vsel_reg = BD71837_REG_BUCK6_VOLT,
+ .vsel_mask = BUCK6_MASK,
+ .enable_reg = BD71837_REG_BUCK6_CTRL,
+ .enable_mask = BD71837_BUCK_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "buck7",
+ .of_match = of_match_ptr("BUCK7"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_BUCK7,
+ .ops = &bd71837_buck_regulator_nolinear_ops,
+ .type = REGULATOR_VOLTAGE,
+ .volt_table = &buck_7_volts[0],
+ .n_voltages = ARRAY_SIZE(buck_7_volts),
+ .vsel_reg = BD71837_REG_BUCK7_VOLT,
+ .vsel_mask = BUCK7_MASK,
+ .enable_reg = BD71837_REG_BUCK7_CTRL,
+ .enable_mask = BD71837_BUCK_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "buck8",
+ .of_match = of_match_ptr("BUCK8"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_BUCK8,
+ .ops = &bd71837_buck_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = BD71837_BUCK8_VOLTAGE_NUM,
+ .linear_ranges = bd71837_buck8_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(bd71837_buck8_voltage_ranges),
+ .vsel_reg = BD71837_REG_BUCK8_VOLT,
+ .vsel_mask = BUCK8_MASK,
+ .enable_reg = BD71837_REG_BUCK8_CTRL,
+ .enable_mask = BD71837_BUCK_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "ldo1",
+ .of_match = of_match_ptr("LDO1"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_LDO1,
+ .ops = &bd71837_ldo_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = BD71837_LDO1_VOLTAGE_NUM,
+ .linear_ranges = bd71837_ldo1_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(bd71837_ldo1_voltage_ranges),
+ .vsel_reg = BD71837_REG_LDO1_VOLT,
+ .vsel_mask = LDO1_MASK,
+ .enable_reg = BD71837_REG_LDO1_VOLT,
+ .enable_mask = BD71837_LDO_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "ldo2",
+ .of_match = of_match_ptr("LDO2"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_LDO2,
+ .ops = &bd71837_ldo_regulator_nolinear_ops,
+ .type = REGULATOR_VOLTAGE,
+ .volt_table = &ldo_2_volts[0],
+ .vsel_reg = BD71837_REG_LDO2_VOLT,
+ .vsel_mask = LDO2_MASK,
+ .n_voltages = ARRAY_SIZE(ldo_2_volts),
+ .n_voltages = BD71837_LDO2_VOLTAGE_NUM,
+ .enable_reg = BD71837_REG_LDO2_VOLT,
+ .enable_mask = BD71837_LDO_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "ldo3",
+ .of_match = of_match_ptr("LDO3"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_LDO3,
+ .ops = &bd71837_ldo_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = BD71837_LDO3_VOLTAGE_NUM,
+ .linear_ranges = bd71837_ldo3_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(bd71837_ldo3_voltage_ranges),
+ .vsel_reg = BD71837_REG_LDO3_VOLT,
+ .vsel_mask = LDO3_MASK,
+ .enable_reg = BD71837_REG_LDO3_VOLT,
+ .enable_mask = BD71837_LDO_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "ldo4",
+ .of_match = of_match_ptr("LDO4"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_LDO4,
+ .ops = &bd71837_ldo_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = BD71837_LDO4_VOLTAGE_NUM,
+ .linear_ranges = bd71837_ldo4_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(bd71837_ldo4_voltage_ranges),
+ .vsel_reg = BD71837_REG_LDO4_VOLT,
+ .vsel_mask = LDO4_MASK,
+ .enable_reg = BD71837_REG_LDO4_VOLT,
+ .enable_mask = BD71837_LDO_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "ldo5",
+ .of_match = of_match_ptr("LDO5"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_LDO5,
+ .ops = &bd71837_ldo_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = BD71837_LDO5_VOLTAGE_NUM,
+ .linear_ranges = bd71837_ldo5_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(bd71837_ldo5_voltage_ranges),
+ /* LDO5 is supplied by buck6 */
+ .supply_name = "buck6",
+ .vsel_reg = BD71837_REG_LDO5_VOLT,
+ .vsel_mask = LDO5_MASK,
+ .enable_reg = BD71837_REG_LDO5_VOLT,
+ .enable_mask = BD71837_LDO_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "ldo6",
+ .of_match = of_match_ptr("LDO6"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_LDO6,
+ .ops = &bd71837_ldo_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = BD71837_LDO6_VOLTAGE_NUM,
+ .linear_ranges = bd71837_ldo6_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(bd71837_ldo6_voltage_ranges),
+ /* LDO6 is supplied by buck7 */
+ .supply_name = "buck7",
+ .vsel_reg = BD71837_REG_LDO6_VOLT,
+ .vsel_mask = LDO6_MASK,
+ .enable_reg = BD71837_REG_LDO6_VOLT,
+ .enable_mask = BD71837_LDO_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "ldo7",
+ .of_match = of_match_ptr("LDO7"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_LDO7,
+ .ops = &bd71837_ldo_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = BD71837_LDO7_VOLTAGE_NUM,
+ .linear_ranges = bd71837_ldo7_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(bd71837_ldo7_voltage_ranges),
+ .vsel_reg = BD71837_REG_LDO7_VOLT,
+ .vsel_mask = LDO7_MASK,
+ .enable_reg = BD71837_REG_LDO7_VOLT,
+ .enable_mask = BD71837_LDO_EN,
+ .owner = THIS_MODULE,
+ },
+};
+
+struct reg_init {
+ unsigned int reg;
+ unsigned int mask;
+};
+
+static int bd71837_probe(struct platform_device *pdev)
+{
+ struct bd71837_pmic *pmic;
+ struct bd71837_board *pdata;
+ struct regulator_config config = { 0 };
+ struct reg_init pmic_regulator_inits[] = {
+ {
+ .reg = BD71837_REG_BUCK1_CTRL,
+ .mask = BD71837_BUCK_SEL,
+ }, {
+ .reg = BD71837_REG_BUCK2_CTRL,
+ .mask = BD71837_BUCK_SEL,
+ }, {
+ .reg = BD71837_REG_BUCK3_CTRL,
+ .mask = BD71837_BUCK_SEL,
+ }, {
+ .reg = BD71837_REG_BUCK4_CTRL,
+ .mask = BD71837_BUCK_SEL,
+ }, {
+ .reg = BD71837_REG_BUCK5_CTRL,
+ .mask = BD71837_BUCK_SEL,
+ }, {
+ .reg = BD71837_REG_BUCK6_CTRL,
+ .mask = BD71837_BUCK_SEL,
+ }, {
+ .reg = BD71837_REG_BUCK7_CTRL,
+ .mask = BD71837_BUCK_SEL,
+ }, {
+ .reg = BD71837_REG_BUCK8_CTRL,
+ .mask = BD71837_BUCK_SEL,
+ }, {
+ .reg = BD71837_REG_LDO1_VOLT,
+ .mask = BD71837_LDO_SEL,
+ }, {
+ .reg = BD71837_REG_LDO2_VOLT,
+ .mask = BD71837_LDO_SEL,
+ }, {
+ .reg = BD71837_REG_LDO3_VOLT,
+ .mask = BD71837_LDO_SEL,
+ }, {
+ .reg = BD71837_REG_LDO4_VOLT,
+ .mask = BD71837_LDO_SEL,
+ }, {
+ .reg = BD71837_REG_LDO5_VOLT,
+ .mask = BD71837_LDO_SEL,
+ }, {
+ .reg = BD71837_REG_LDO6_VOLT,
+ .mask = BD71837_LDO_SEL,
+ }, {
+ .reg = BD71837_REG_LDO7_VOLT,
+ .mask = BD71837_LDO_SEL,
+ }
+ };
+
+ int i, err;
+
+ pmic = devm_kzalloc(&pdev->dev, sizeof(struct bd71837_pmic),
+ GFP_KERNEL);
+ if (!pmic)
+ return -ENOMEM;
+
+ mutex_init(&pmic->mtx);
+
+ memcpy(pmic->descs, bd71837_regulators, sizeof(pmic->descs));
+
+ pmic->pdev = pdev;
+ pmic->mfd = dev_get_drvdata(pdev->dev.parent);
+
+ if (!pmic->mfd) {
+ dev_err(&pdev->dev, "No MFD driver data\n");
+ err = -EINVAL;
+ goto err;
+ }
+ platform_set_drvdata(pdev, pmic);
+ pdata = dev_get_platdata(pmic->mfd->dev);
+
+ /* Register LOCK release */
+ err = regmap_update_bits(pmic->mfd->regmap, BD71837_REG_REGLOCK,
+ (REGLOCK_PWRSEQ | REGLOCK_VREG), 0);
+ if (err) {
+ dev_err(&pmic->pdev->dev, "Failed to unlock PMIC (%d)\n", err);
+ goto err;
+ } else {
+ dev_dbg(&pmic->pdev->dev, "%s: Unlocked lock register 0x%x\n",
+ __func__, BD71837_REG_REGLOCK);
+ }
+
+ for (i = 0; i < ARRAY_SIZE(pmic_regulator_inits); i++) {
+
+ struct regulator_desc *desc;
+ struct regulator_dev *rdev;
+
+ desc = &pmic->descs[i];
+
+ if (pdata)
+ config.init_data = pdata->init_data[i];
+
+ config.dev = pdev->dev.parent;
+ config.driver_data = pmic;
+ config.regmap = pmic->mfd->regmap;
+
+ rdev = devm_regulator_register(&pdev->dev, desc, &config);
+ if (IS_ERR(rdev)) {
+ dev_err(pmic->mfd->dev,
+ "failed to register %s regulator\n",
+ desc->name);
+ err = PTR_ERR(rdev);
+ goto err;
+ }
+ /* Regulator register gets the regulator constraints and
+ * applies them (set_machine_constraints). This should have
+ * turned the control register(s) to correct values and we
+ * can now switch the control from PMIC state machine to the
+ * register interface
+ */
+ err = regmap_update_bits(pmic->mfd->regmap,
+ pmic_regulator_inits[i].reg,
+ pmic_regulator_inits[i].mask,
+ 0xFFFFFFFF);
+ if (err) {
+ dev_err(&pmic->pdev->dev,
+ "Failed to write BUCK/LDO SEL bit for (%s)\n",
+ desc->name);
+ goto err;
+ }
+
+ pmic->rdev[i] = rdev;
+ }
+
+ return 0;
+
+err:
+ return err;
+}
+
+static struct platform_driver bd71837_regulator = {
+ .driver = {
+ .name = "bd71837-pmic",
+ .owner = THIS_MODULE,
+ },
+ .probe = bd71837_probe,
+};
+
+module_platform_driver(bd71837_regulator);
+
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
+MODULE_DESCRIPTION("BD71837 voltage regulator driver");
+MODULE_LICENSE("GPL");
--
2.14.3
^ permalink raw reply related [flat|nested] 11+ messages in thread