From: Johan Hovold <johan@kernel.org>
To: Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>
Cc: Andreas Kemnade <andreas@kemnade.info>,
Arnd Bergmann <arnd@arndb.de>,
"H . Nikolaus Schaller" <hns@goldelico.com>,
Pavel Machek <pavel@ucw.cz>,
Marcel Holtmann <marcel@holtmann.org>,
Sebastian Reichel <sebastian.reichel@collabora.co.uk>,
Tony Lindgren <tony@atomide.com>,
linux-kernel@vger.kernel.org, devicetree@vger.kernel.org,
Johan Hovold <johan@kernel.org>
Subject: [PATCH v2 6/8] dt-bindings: gnss: add sirfstar binding
Date: Wed, 30 May 2018 12:32:40 +0200 [thread overview]
Message-ID: <20180530103242.20773-7-johan@kernel.org> (raw)
In-Reply-To: <20180530103242.20773-1-johan@kernel.org>
Add binding for SiRFstar-based GNSS receivers.
Note that while four compatible-strings are initially added representing
devices which differ in which I/O interfaces they support, they
otherwise essentially share the same feature set.
Pin and supply names vary slightly, as do some recommended timings.
Note that the wakeup gpio is not intended to be used as a wakeup source,
but rather to detect the current power state of the device (active or
hibernate).
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
---
.../devicetree/bindings/gnss/sirfstar.txt | 45 +++++++++++++++++++
.../devicetree/bindings/vendor-prefixes.txt | 3 ++
2 files changed, 48 insertions(+)
create mode 100644 Documentation/devicetree/bindings/gnss/sirfstar.txt
diff --git a/Documentation/devicetree/bindings/gnss/sirfstar.txt b/Documentation/devicetree/bindings/gnss/sirfstar.txt
new file mode 100644
index 000000000000..5803a7831f81
--- /dev/null
+++ b/Documentation/devicetree/bindings/gnss/sirfstar.txt
@@ -0,0 +1,45 @@
+SiRFstar-based GNSS Receiver DT binding
+
+SiRFstar chipsets are used in GNSS-receiver modules produced by several
+vendors and can use UART, SPI or I2C interfaces.
+
+Please see Documentation/devicetree/bindings/gnss/gnss.txt for generic
+properties.
+
+Required properties:
+
+- compatible : Must be one of
+
+ "fastrax,uc430"
+ "linx,r4"
+ "wi2wi,w2sg0008i"
+ "wi2wi,w2sg0084i"
+
+- vcc-supply : Main voltage regulator (pin name: 3V3_IN, VCC, VDD)
+
+Required properties (I2C):
+- reg : I2C slave address
+
+Required properties (SPI):
+- reg : SPI chip select address
+
+Optional properties:
+
+- sirf,onoff-gpios : GPIO used to power on and off device (pin name: ON_OFF)
+- sirf,wakeup-gpios : GPIO used to determine device power state
+ (pin name: RFPWRUP, WAKEUP)
+- timepulse-gpios : Time pulse GPIO (pin name: 1PPS, TM)
+
+Example:
+
+serial@1234 {
+ compatible = "ns16550a";
+
+ gnss {
+ compatible = "wi2wi,w2sg0084i";
+
+ vcc-supply = <&gnss_reg>;
+ sirf,onoff-gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+ sirf,wakeup-gpios = <&gpio0 17 GPIO_ACTIVE_HIGH>;
+ };
+};
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 2128dfdf73f1..61db9d2391c4 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -120,6 +120,7 @@ excito Excito
ezchip EZchip Semiconductor
fairphone Fairphone B.V.
faraday Faraday Technology Corporation
+fastrax Fastrax Oy
fcs Fairchild Semiconductor
firefly Firefly
focaltech FocalTech Systems Co.,Ltd
@@ -197,6 +198,7 @@ licheepi Lichee Pi
linaro Linaro Limited
linksys Belkin International, Inc. (Linksys)
linux Linux-specific binding
+linx Linx Technologies
lltc Linear Technology Corporation
lsi LSI Corp. (LSI Logic)
lwn Liebherr-Werk Nenzing GmbH
@@ -393,6 +395,7 @@ vot Vision Optical Technology Co., Ltd.
wd Western Digital Corp.
wetek WeTek Electronics, limited.
wexler Wexler
+wi2wi Wi2Wi, Inc.
winbond Winbond Electronics corp.
winstar Winstar Display Corp.
wlf Wolfson Microelectronics
--
2.17.0
next prev parent reply other threads:[~2018-05-30 10:32 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-05-30 10:32 [PATCH v2 0/8] gnss: add new GNSS subsystem Johan Hovold
2018-05-30 10:32 ` [PATCH v2 1/8] gnss: add GNSS receiver subsystem Johan Hovold
2018-05-30 10:32 ` [PATCH v2 2/8] dt-bindings: add generic gnss binding Johan Hovold
2018-05-30 10:32 ` [PATCH v2 3/8] gnss: add generic serial driver Johan Hovold
2018-05-30 10:32 ` [PATCH v2 4/8] dt-bindings: gnss: add u-blox binding Johan Hovold
2018-05-31 3:58 ` Rob Herring
2018-05-31 8:22 ` Johan Hovold
2018-05-31 13:55 ` Rob Herring
2018-05-31 14:34 ` Johan Hovold
2018-05-31 15:58 ` Rob Herring
2018-06-01 8:15 ` Johan Hovold
2018-05-30 10:32 ` [PATCH v2 5/8] gnss: add driver for u-blox receivers Johan Hovold
2018-06-02 6:07 ` kbuild test robot
2018-06-02 6:07 ` [RFC PATCH] gnss: ubx_gserial_ops can be static kbuild test robot
2018-05-30 10:32 ` Johan Hovold [this message]
2018-05-30 10:32 ` [PATCH v2 7/8] gnss: add driver for sirfstar-based receivers Johan Hovold
2018-05-30 10:32 ` [PATCH v2 8/8] gnss: add device type support Johan Hovold
2018-05-30 14:38 ` [PATCH v2 0/8] gnss: add new GNSS subsystem Richard Cochran
2018-05-31 8:52 ` Johan Hovold
2018-05-31 9:52 ` H. Nikolaus Schaller
2018-05-31 11:47 ` Johan Hovold
2018-05-31 13:33 ` H. Nikolaus Schaller
2018-05-31 13:37 ` Johan Hovold
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180530103242.20773-7-johan@kernel.org \
--to=johan@kernel.org \
--cc=andreas@kemnade.info \
--cc=arnd@arndb.de \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=hns@goldelico.com \
--cc=linux-kernel@vger.kernel.org \
--cc=marcel@holtmann.org \
--cc=mark.rutland@arm.com \
--cc=pavel@ucw.cz \
--cc=robh+dt@kernel.org \
--cc=sebastian.reichel@collabora.co.uk \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).