From: Johan Hovold <johan@kernel.org>
To: Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>
Cc: Andreas Kemnade <andreas@kemnade.info>,
Arnd Bergmann <arnd@arndb.de>,
"H . Nikolaus Schaller" <hns@goldelico.com>,
Pavel Machek <pavel@ucw.cz>,
Marcel Holtmann <marcel@holtmann.org>,
Sebastian Reichel <sebastian.reichel@collabora.co.uk>,
Tony Lindgren <tony@atomide.com>,
linux-kernel@vger.kernel.org, devicetree@vger.kernel.org,
Johan Hovold <johan@kernel.org>
Subject: [PATCH v3 4/8] dt-bindings: gnss: add u-blox binding
Date: Fri, 1 Jun 2018 10:22:55 +0200 [thread overview]
Message-ID: <20180601082259.17563-5-johan@kernel.org> (raw)
In-Reply-To: <20180601082259.17563-1-johan@kernel.org>
Add binding for u-blox GNSS receivers.
Note that the u-blox product names encodes form factor (e.g. "neo"),
chipset (e.g. "8") and variant (e.g. "q"), but that only formfactor and
chipset is used for the compatible strings (for now).
Signed-off-by: Johan Hovold <johan@kernel.org>
---
.../devicetree/bindings/gnss/u-blox.txt | 44 +++++++++++++++++++
.../devicetree/bindings/vendor-prefixes.txt | 1 +
2 files changed, 45 insertions(+)
create mode 100644 Documentation/devicetree/bindings/gnss/u-blox.txt
diff --git a/Documentation/devicetree/bindings/gnss/u-blox.txt b/Documentation/devicetree/bindings/gnss/u-blox.txt
new file mode 100644
index 000000000000..e475659cb85f
--- /dev/null
+++ b/Documentation/devicetree/bindings/gnss/u-blox.txt
@@ -0,0 +1,44 @@
+u-blox GNSS Receiver DT binding
+
+The u-blox GNSS receivers can use UART, DDC (I2C), SPI and USB interfaces.
+
+Please see Documentation/devicetree/bindings/gnss/gnss.txt for generic
+properties.
+
+Required properties:
+
+- compatible : Must be one of
+
+ "u-blox,neo-8"
+ "u-blox,neo-m8"
+
+- vcc-supply : Main voltage regulator
+
+Required properties (DDC):
+- reg : DDC (I2C) slave address
+
+Required properties (SPI):
+- reg : SPI chip select address
+
+Required properties (USB):
+- reg : Number of the USB hub port or the USB host-controller port
+ to which this device is attached
+
+Optional properties:
+
+- timepulse-gpios : Time pulse GPIO
+- u-blox,extint-gpios : GPIO connected to the "external interrupt" input pin
+- v-bckp-supply : Backup voltage regulator
+
+Example:
+
+serial@1234 {
+ compatible = "ns16550a";
+
+ gnss {
+ compatible = "u-blox,neo-8";
+
+ v-bckp-supply = <&gnss_v_bckp_reg>;
+ vcc-supply = <&gnss_vcc_reg>;
+ };
+};
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index b5f978a4cac6..2128dfdf73f1 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -374,6 +374,7 @@ tronsmart Tronsmart
truly Truly Semiconductors Limited
tsd Theobroma Systems Design und Consulting GmbH
tyan Tyan Computer Corporation
+u-blox u-blox
ucrobotics uCRobotics
ubnt Ubiquiti Networks
udoo Udoo
--
2.17.1
next prev parent reply other threads:[~2018-06-01 8:22 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-06-01 8:22 [PATCH v3 0/8] gnss: add new GNSS subsystem Johan Hovold
2018-06-01 8:22 ` [PATCH v3 1/8] gnss: add GNSS receiver subsystem Johan Hovold
2018-06-01 8:22 ` [PATCH v3 2/8] dt-bindings: add generic gnss binding Johan Hovold
2018-06-01 8:22 ` [PATCH v3 3/8] gnss: add generic serial driver Johan Hovold
2018-06-01 8:22 ` Johan Hovold [this message]
2018-06-01 14:34 ` [PATCH v3 4/8] dt-bindings: gnss: add u-blox binding Rob Herring
2018-06-01 8:22 ` [PATCH v3 5/8] gnss: add driver for u-blox receivers Johan Hovold
2018-06-01 8:22 ` [PATCH v3 6/8] dt-bindings: gnss: add sirfstar binding Johan Hovold
2018-06-01 8:22 ` [PATCH v3 7/8] gnss: add driver for sirfstar-based receivers Johan Hovold
2018-06-01 8:22 ` [PATCH v3 8/8] gnss: add receiver type support Johan Hovold
2018-06-01 9:33 ` [PATCH v3 0/8] gnss: add new GNSS subsystem Pavel Machek
2018-06-01 9:49 ` Johan Hovold
2018-06-01 10:26 ` Pavel Machek
2018-06-01 12:22 ` Johan Hovold
2018-06-01 16:26 ` Pavel Machek
2018-06-01 16:37 ` H. Nikolaus Schaller
2018-06-01 21:46 ` Pavel Machek
2018-06-04 10:22 ` Johan Hovold
2018-06-05 21:47 ` Pavel Machek
2018-06-13 8:21 ` Johan Hovold
2018-06-28 12:01 ` Greg Kroah-Hartman
2018-06-29 9:46 ` Pavel Machek
2018-06-29 11:46 ` Johan Hovold
2018-06-29 12:05 ` Pavel Machek
2018-06-29 12:09 ` Johan Hovold
2018-07-02 19:32 ` Pavel Machek
2018-07-03 7:20 ` Johan Hovold
2018-06-29 18:26 ` Greg Kroah-Hartman
2018-07-02 19:01 ` Pavel Machek
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180601082259.17563-5-johan@kernel.org \
--to=johan@kernel.org \
--cc=andreas@kemnade.info \
--cc=arnd@arndb.de \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=hns@goldelico.com \
--cc=linux-kernel@vger.kernel.org \
--cc=marcel@holtmann.org \
--cc=mark.rutland@arm.com \
--cc=pavel@ucw.cz \
--cc=robh+dt@kernel.org \
--cc=sebastian.reichel@collabora.co.uk \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).