* [PATCH v2 1/2] ARM: dts: imx6ul: Add DTS for ConnectCore 6UL System-On-Module (SOM)
2018-07-12 8:20 [PATCH v2 0/2] Add support for the ConnectCore 6UL SOM and SBC Express Alex Gonzalez
@ 2018-07-12 8:20 ` Alex Gonzalez
2018-07-12 8:20 ` [PATCH v2 2/2] ARM: dts: imx6ul: Add DTS for ConnectCore 6UL SBC Express Alex Gonzalez
2018-07-17 3:41 ` [PATCH v2 0/2] Add support for the ConnectCore 6UL SOM and " Shawn Guo
2 siblings, 0 replies; 4+ messages in thread
From: Alex Gonzalez @ 2018-07-12 8:20 UTC (permalink / raw)
To: shawnguo
Cc: robh+dt, mark.rutland, s.hauer, kernel, fabio.estevam, linux-imx,
devicetree, linux-kernel, linux-arm-kernel, alex.gonzalez
The ConnectCore 6UL System-On-Module has the following hardware
specification:
* Based on a NXP i.MX6UL SoC
* Industrial temperature ranges (-40ºC to +85ºC)
* Up to 1GB DDR3 memory
* Up to 2GB NAND flash
* Dual Ethernet
* On module 802.11 WiFi and Bluetooth 4.2 (QCA6564)
* On module NXP Kinetis KL03
* On module Microchip ATECC508A crypto element
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
---
arch/arm/boot/dts/imx6ul-ccimx6ulsom.dtsi | 202 ++++++++++++++++++++++++++++++
1 file changed, 202 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6ul-ccimx6ulsom.dtsi
diff --git a/arch/arm/boot/dts/imx6ul-ccimx6ulsom.dtsi b/arch/arm/boot/dts/imx6ul-ccimx6ulsom.dtsi
new file mode 100644
index 000000000000..255c482ce56f
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-ccimx6ulsom.dtsi
@@ -0,0 +1,202 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Digi International's ConnectCore 6UL System-On-Module device tree source
+ *
+ * Copyright 2018 Digi International, Inc.
+ *
+ */
+
+/ {
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ linux,cma {
+ compatible = "shared-dma-pool";
+ reusable;
+ size = <0x4000000>;
+ linux,cma-default;
+ };
+ };
+};
+
+&adc1 {
+ vref-supply = <&vdda_adc_3v3>;
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ pfuze3000: pmic@8 {
+ compatible = "fsl,pfuze3000";
+ reg = <0x08>;
+
+ regulators {
+ int_3v3: sw1a {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-ramp-delay = <6250>;
+ regulator-boot-on;
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_arm_soc_in: sw1b {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1475000>;
+ regulator-ramp-delay = <6250>;
+ regulator-boot-on;
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <925000>;
+ };
+ };
+
+ ext_3v3: sw2 {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-ramp-delay = <6250>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr3: sw3 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1650000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1300000>;
+ };
+ };
+
+ swbst_reg: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ };
+
+ vdd_snvs_3v3: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vrefddr: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdda_adc_3v3: vldo1 {
+ compatible = "regulator-fixed";
+ regulator-name = "vref-adc-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo2_ext: vldo2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vdda_wlan: vccsd {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_high_in: v33 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3_int: vldo3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo4_ext: vldo4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vcoin_chg: vcoin {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+ };
+};
+
+&iomuxc {
+ pinctrl_gpmi_nand: gpmigrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B 0xb0b1
+ MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B 0xb0b1
+ MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B 0xb0b1
+ MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B 0xb0b1
+ MX6UL_PAD_NAND_ALE__RAWNAND_ALE 0xb0b1
+ MX6UL_PAD_NAND_CLE__RAWNAND_CLE 0xb0b1
+ MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00 0xb0b1
+ MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01 0xb0b1
+ MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02 0xb0b1
+ MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03 0xb0b1
+ MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04 0xb0b1
+ MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05 0xb0b1
+ MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06 0xb0b1
+ MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07 0xb0b1
+ MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B 0xb0b1
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0
+ MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0
+ >;
+ };
+};
+
+®_arm {
+ vin-supply = <&vdd_arm_soc_in>;
+ regulator-allow-bypass;
+};
+
+®_soc {
+ vin-supply = <&vdd_arm_soc_in>;
+ regulator-allow-bypass;
+};
+
^ permalink raw reply related [flat|nested] 4+ messages in thread* [PATCH v2 2/2] ARM: dts: imx6ul: Add DTS for ConnectCore 6UL SBC Express
2018-07-12 8:20 [PATCH v2 0/2] Add support for the ConnectCore 6UL SOM and SBC Express Alex Gonzalez
2018-07-12 8:20 ` [PATCH v2 1/2] ARM: dts: imx6ul: Add DTS for ConnectCore 6UL System-On-Module (SOM) Alex Gonzalez
@ 2018-07-12 8:20 ` Alex Gonzalez
2018-07-17 3:41 ` [PATCH v2 0/2] Add support for the ConnectCore 6UL SOM and " Shawn Guo
2 siblings, 0 replies; 4+ messages in thread
From: Alex Gonzalez @ 2018-07-12 8:20 UTC (permalink / raw)
To: shawnguo
Cc: robh+dt, mark.rutland, s.hauer, kernel, fabio.estevam, linux-imx,
devicetree, linux-kernel, linux-arm-kernel, alex.gonzalez
The ConnectCore 6UL Single Board Computer (SBC) Express contains the
ConnectCore 6UL System-On-Module.
Its hardware specifications are:
* 256MB DDR3 memory
* 256MB NAND flash
* Single Ethernet
* USB Host and USB-OTG
* MicroSD external storage
* Groove connectors and Raspberry Pi Hat compatible expansion header
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6ul-ccimx6ulsbcexpress.dts | 200 ++++++++++++++++++++++++
2 files changed, 201 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6ul-ccimx6ulsbcexpress.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 37a3de760d40..6135d3dc381c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -533,6 +533,7 @@ dtb-$(CONFIG_SOC_IMX6SX) += \
imx6sx-udoo-neo-full.dtb
dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ul-14x14-evk.dtb \
+ imx6ul-ccimx6ulsbcexpress.dtb \
imx6ul-geam.dtb \
imx6ul-isiot-emmc.dtb \
imx6ul-isiot-nand.dtb \
diff --git a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcexpress.dts b/arch/arm/boot/dts/imx6ul-ccimx6ulsbcexpress.dts
new file mode 100644
index 000000000000..3792679c0c90
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-ccimx6ulsbcexpress.dts
@@ -0,0 +1,200 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Digi International's ConnectCore6UL SBC Express board device tree source
+ *
+ * Copyright 2018 Digi International, Inc.
+ *
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx6ul.dtsi"
+#include "imx6ul-ccimx6ulsom.dtsi"
+
+/ {
+ model = "Digi International ConnectCore 6UL SBC Express.";
+ compatible = "digi,ccimx6ulsbcexpress", "digi,ccimx6ulsom",
+ "fsl,imx6ul";
+};
+
+&adc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc1>;
+ status = "okay";
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ xceiver-supply = <&ext_3v3>;
+ status = "okay";
+};
+
+&ecspi3 {
+ cs-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3_master>;
+ status = "okay";
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy0>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ smsc,disable-energy-detect;
+ reg = <0>;
+ };
+ };
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ status = "okay";
+};
+
+&usbotg1 {
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usbotg2 {
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ broken-cd; /* no carrier detect line (use polling) */
+ no-1-8-v;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ pinctrl_adc1: adc1grp {
+ fsl,pins = <
+ /* GPIO1_4/ADC1_IN4 (pin 7 of the expansion header) */
+ MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0xb0
+ >;
+ };
+
+ pinctrl_ecspi3_master: ecspi3grp1 {
+ fsl,pins = <
+ MX6UL_PAD_UART2_RX_DATA__ECSPI3_SCLK 0x10b0
+ MX6UL_PAD_UART2_CTS_B__ECSPI3_MOSI 0x10b0
+ MX6UL_PAD_UART2_RTS_B__ECSPI3_MISO 0x10b0
+ MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20 0x10b0 /* Chip Select */
+ >;
+ };
+
+ pinctrl_ecspi3_slave: ecspi3grp2 {
+ fsl,pins = <
+ MX6UL_PAD_UART2_RX_DATA__ECSPI3_SCLK 0x10b0
+ MX6UL_PAD_UART2_CTS_B__ECSPI3_MOSI 0x10b0
+ MX6UL_PAD_UART2_RTS_B__ECSPI3_MISO 0x10b0
+ MX6UL_PAD_UART2_TX_DATA__ECSPI3_SS0 0x10b0 /* Chip Select */
+ >;
+ };
+
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x1b0b0
+ MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0
+ MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x40017051
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp{
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA08__FLEXCAN1_TX 0x1b020
+ MX6UL_PAD_LCD_DATA09__FLEXCAN1_RX 0x1b020
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO00__I2C2_SCL 0x4001b8b0
+ MX6UL_PAD_GPIO1_IO01__I2C2_SDA 0x4001b8b0
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA00__PWM1_OUT 0x10b0
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_CLK__UART4_DCE_TX 0x1b0b1
+ MX6UL_PAD_LCD_ENABLE__UART4_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_HSYNC__USDHC2_CMD 0x17059
+ MX6UL_PAD_CSI_VSYNC__USDHC2_CLK 0x10071
+ MX6UL_PAD_CSI_DATA00__USDHC2_DATA0 0x17059
+ MX6UL_PAD_CSI_DATA01__USDHC2_DATA1 0x17059
+ MX6UL_PAD_CSI_DATA02__USDHC2_DATA2 0x17059
+ MX6UL_PAD_CSI_DATA03__USDHC2_DATA3 0x17059
+ >;
+ };
+
+ /* General purpose pinctrl */
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ /* GPIOs BANK 3 */
+ MX6UL_PAD_LCD_RESET__GPIO3_IO04 0xf030
+ >;
+ };
+};
^ permalink raw reply related [flat|nested] 4+ messages in thread* Re: [PATCH v2 0/2] Add support for the ConnectCore 6UL SOM and SBC Express
2018-07-12 8:20 [PATCH v2 0/2] Add support for the ConnectCore 6UL SOM and SBC Express Alex Gonzalez
2018-07-12 8:20 ` [PATCH v2 1/2] ARM: dts: imx6ul: Add DTS for ConnectCore 6UL System-On-Module (SOM) Alex Gonzalez
2018-07-12 8:20 ` [PATCH v2 2/2] ARM: dts: imx6ul: Add DTS for ConnectCore 6UL SBC Express Alex Gonzalez
@ 2018-07-17 3:41 ` Shawn Guo
2 siblings, 0 replies; 4+ messages in thread
From: Shawn Guo @ 2018-07-17 3:41 UTC (permalink / raw)
To: Alex Gonzalez
Cc: robh+dt, mark.rutland, s.hauer, kernel, fabio.estevam, linux-imx,
devicetree, linux-kernel, linux-arm-kernel
On Thu, Jul 12, 2018 at 10:20:34AM +0200, Alex Gonzalez wrote:
> Alex Gonzalez (2):
> ARM: dts: imx6ul: Add DTS for ConnectCore 6UL System-On-Module (SOM)
> ARM: dts: imx6ul: Add DTS for ConnectCore 6UL SBC Express
Applied both, thanks.
^ permalink raw reply [flat|nested] 4+ messages in thread