From: Quentin Schulz <quentin.schulz@bootlin.com>
To: Andrew Lunn <andrew@lunn.ch>
Cc: alexandre.belloni@bootlin.com, ralf@linux-mips.org,
paul.burton@mips.com, jhogan@kernel.org, robh+dt@kernel.org,
mark.rutland@arm.com, davem@davemloft.net, kishon@ti.com,
f.fainelli@gmail.com, linux-mips@linux-mips.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
netdev@vger.kernel.org, allan.nielsen@microsemi.com,
thomas.petazzoni@bootlin.com
Subject: Re: [PATCH 00/10] mscc: ocelot: add support for SerDes muxing configuration
Date: Wed, 1 Aug 2018 09:54:00 +0200 [thread overview]
Message-ID: <20180801075400.cvvasvi2g2m56xp4@qschulz> (raw)
In-Reply-To: <20180730132441.GC13198@lunn.ch>
[-- Attachment #1: Type: text/plain, Size: 847 bytes --]
Hi Andrew,
On Mon, Jul 30, 2018 at 03:24:41PM +0200, Andrew Lunn wrote:
> > The SerDes configuration is in the middle of an address space (HSIO) that
> > is used to configure some parts in the MAC controller driver, that is why
> > we need to use a syscon so that we can write to the same address space from
> > different drivers safely using regmap.
>
> Hi Quentin
>
> I assume breaking backwards compatibility is not an issue here, since
> there currently is only one board using the DT binding. But it would
> be good to give a warning in the cover notes. git bisect will also
> break for this one particular board. And since these changes are going
> through different trees, it could be quite a big break.
>
Yes sorry, I should have mentioned it in the cover letter, will do
if/when there is a v2.
Thanks,
Quentin
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
prev parent reply other threads:[~2018-08-01 7:54 UTC|newest]
Thread overview: 35+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-07-30 12:43 [PATCH 00/10] mscc: ocelot: add support for SerDes muxing configuration Quentin Schulz
2018-07-30 12:43 ` [PATCH net-next 01/10] MIPS: mscc: ocelot: make HSIO registers address range a syscon Quentin Schulz
2018-07-31 7:51 ` Alexandre Belloni
2018-07-30 12:43 ` [PATCH net-next 02/10] dt-bindings: net: ocelot: remove hsio from the list of register address spaces Quentin Schulz
2018-07-31 7:52 ` Alexandre Belloni
2018-08-13 22:31 ` Rob Herring
2018-08-14 6:49 ` Quentin Schulz
2018-08-14 12:41 ` Alexandre Belloni
2018-08-16 14:25 ` Quentin Schulz
2018-08-27 20:57 ` Alexandre Belloni
2018-07-30 12:43 ` [PATCH net-next 03/10] net: mscc: ocelot: get HSIO regmap from syscon Quentin Schulz
2018-07-31 7:53 ` Alexandre Belloni
2018-07-30 12:43 ` [PATCH net-next 04/10] net: mscc: ocelot: move the HSIO header to include/soc Quentin Schulz
2018-07-31 8:02 ` Alexandre Belloni
2018-07-30 12:43 ` [PATCH net-next 05/10] net: mscc: ocelot: simplify register access for PLL5 configuration Quentin Schulz
2018-07-31 8:02 ` Alexandre Belloni
2018-07-30 12:43 ` [PATCH 06/10] phy: add QSGMII and PCIE modes Quentin Schulz
2018-07-30 12:43 ` [PATCH 07/10] dt-bindings: phy: add DT binding for Microsemi Ocelot SerDes muxing Quentin Schulz
2018-07-30 13:34 ` Andrew Lunn
2018-08-01 8:24 ` Quentin Schulz
2018-08-01 14:31 ` Andrew Lunn
2018-08-06 12:47 ` Quentin Schulz
2018-07-30 13:38 ` Andrew Lunn
2018-07-30 21:39 ` Florian Fainelli
2018-08-01 8:15 ` Quentin Schulz
2018-08-13 22:37 ` Rob Herring
2018-08-14 12:45 ` Alexandre Belloni
2018-07-30 12:43 ` [PATCH 08/10] MIPS: mscc: ocelot: add SerDes mux DT node Quentin Schulz
2018-07-30 12:43 ` [PATCH 09/10] phy: add driver for Microsemi Ocelot SerDes muxing Quentin Schulz
2018-07-30 12:43 ` [PATCH net-next 10/10] net: mscc: ocelot: make use of SerDes PHYs for handling their configuration Quentin Schulz
2018-07-30 13:50 ` Andrew Lunn
2018-08-01 7:51 ` Quentin Schulz
2018-07-30 13:01 ` [PATCH 00/10] mscc: ocelot: add support for SerDes muxing configuration Quentin Schulz
2018-07-30 13:24 ` Andrew Lunn
2018-08-01 7:54 ` Quentin Schulz [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180801075400.cvvasvi2g2m56xp4@qschulz \
--to=quentin.schulz@bootlin.com \
--cc=alexandre.belloni@bootlin.com \
--cc=allan.nielsen@microsemi.com \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=f.fainelli@gmail.com \
--cc=jhogan@kernel.org \
--cc=kishon@ti.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mips@linux-mips.org \
--cc=mark.rutland@arm.com \
--cc=netdev@vger.kernel.org \
--cc=paul.burton@mips.com \
--cc=ralf@linux-mips.org \
--cc=robh+dt@kernel.org \
--cc=thomas.petazzoni@bootlin.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).