Re: [PATCH v4 1/3] Input: edt-ft5x06 - Add support for regulator

[Dmitry Torokhov <dmitry.torokhov@gmail.com>]

On Tue, Aug 07, 2018 at 08:59:44AM +0200, Mylène Josserand wrote:
> Hello Dmitry,
> 
> Thank you again for the review.
> 
> On Wed, 25 Jul 2018 17:47:32 -0700
> Dmitry Torokhov <dmitry.torokhov@gmail.com> wrote:
> 
> > Hi Mylène,
> > 
> > On Wed, Jul 25, 2018 at 09:34:08AM +0200, Mylène Josserand wrote:
> > > Add the support of regulator to use it as VCC source.
> > > 
> > > Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
> > > Reviewed-by: Rob Herring <robh@kernel.org>
> > > ---
> > >  .../bindings/input/touchscreen/edt-ft5x06.txt      |  1 +
> > >  drivers/input/touchscreen/edt-ft5x06.c             | 43 ++++++++++++++++++++++
> > >  2 files changed, 44 insertions(+)
> > > 
> > > diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> > > index 025cf8c9324a..48e975b9c1aa 100644
> > > --- a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> > > +++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> > > @@ -30,6 +30,7 @@ Required properties:
> > >  Optional properties:
> > >   - reset-gpios: GPIO specification for the RESET input
> > >   - wake-gpios:  GPIO specification for the WAKE input
> > > + - vcc-supply:  Regulator that supplies the touchscreen
> > >  
> > >   - pinctrl-names: should be "default"
> > >   - pinctrl-0:   a phandle pointing to the pin settings for the
> > > diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c
> > > index 1e18ca0d1b4e..dcde719094f7 100644
> > > --- a/drivers/input/touchscreen/edt-ft5x06.c
> > > +++ b/drivers/input/touchscreen/edt-ft5x06.c
> > > @@ -39,6 +39,7 @@
> > >  #include <linux/input/mt.h>
> > >  #include <linux/input/touchscreen.h>
> > >  #include <linux/of_device.h>
> > > +#include <linux/regulator/consumer.h>
> > >  
> > >  #define WORK_REGISTER_THRESHOLD		0x00
> > >  #define WORK_REGISTER_REPORT_RATE	0x08
> > > @@ -91,6 +92,7 @@ struct edt_ft5x06_ts_data {
> > >  	struct touchscreen_properties prop;
> > >  	u16 num_x;
> > >  	u16 num_y;
> > > +	struct regulator *vcc;
> > >  
> > >  	struct gpio_desc *reset_gpio;
> > >  	struct gpio_desc *wake_gpio;
> > > @@ -963,6 +965,13 @@ edt_ft5x06_ts_set_regs(struct edt_ft5x06_ts_data *tsdata)
> > >  	}
> > >  }
> > >  
> > > +static void edt_ft5x06_disable_regulator(void *arg)
> > > +{
> > > +	struct edt_ft5x06_ts_data *data = arg;
> > > +
> > > +	regulator_disable(data->vcc);
> > > +}
> > > +
> > >  static int edt_ft5x06_ts_probe(struct i2c_client *client,
> > >  					 const struct i2c_device_id *id)
> > >  {
> > > @@ -991,6 +1000,28 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
> > >  
> > >  	tsdata->max_support_points = chip_data->max_support_points;
> > >  
> > > +	tsdata->vcc = devm_regulator_get(&client->dev, "vcc");
> > > +	if (IS_ERR(tsdata->vcc)) {
> > > +		error = PTR_ERR(tsdata->vcc);
> > > +		if (error != -EPROBE_DEFER)
> > > +			dev_err(&client->dev, "failed to request regulator: %d\n",
> > > +				error);
> > > +		return error;
> > > +	}
> > > +
> > > +	error = regulator_enable(tsdata->vcc);
> > > +	if (error < 0) {
> > > +		dev_err(&client->dev, "failed to enable vcc: %d\n",
> > > +			error);
> > > +		return error;
> > > +	}  
> > 
> > It is better to put the chip into reset and then power up the regulatori
> > and take it out of the reset, rather than power up and then toggle reset
> > on and off.
> 
> okay, thanks, I will update it.
> 
> > 
> > > +
> > > +	error = devm_add_action_or_reset(&client->dev,
> > > +					 edt_ft5x06_disable_regulator,
> > > +					 tsdata);
> > > +	if (error)
> > > +		return error;
> > > +
> > >  	tsdata->reset_gpio = devm_gpiod_get_optional(&client->dev,
> > >  						     "reset", GPIOD_OUT_HIGH);
> > >  	if (IS_ERR(tsdata->reset_gpio)) {
> > > @@ -1120,9 +1151,12 @@ static int edt_ft5x06_ts_remove(struct i2c_client *client)
> > >  static int __maybe_unused edt_ft5x06_ts_suspend(struct device *dev)
> > >  {
> > >  	struct i2c_client *client = to_i2c_client(dev);
> > > +	struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
> > >  
> > >  	if (device_may_wakeup(dev))
> > >  		enable_irq_wake(client->irq);
> > > +	else
> > > +		regulator_disable(tsdata->vcc);
> > >  
> > >  	return 0;
> > >  }
> > > @@ -1130,9 +1164,18 @@ static int __maybe_unused edt_ft5x06_ts_suspend(struct device *dev)
> > >  static int __maybe_unused edt_ft5x06_ts_resume(struct device *dev)
> > >  {
> > >  	struct i2c_client *client = to_i2c_client(dev);
> > > +	struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
> > > +	int ret;
> > >  
> > >  	if (device_may_wakeup(dev))
> > >  		disable_irq_wake(client->irq);
> > > +	else {
> > > +		ret = regulator_enable(tsdata->vcc);
> > > +		if (ret < 0) {
> > > +			dev_err(dev, "failed to enable vcc: %d\n", ret);
> > > +			return ret;
> > > +		}
> > > +	}  
> > 
> > I believe I mentioned in other review that once you powered up the
> > device, you need to restore its settings, include switching to factory
> > mode, if it was in factory mode, and restoring threshold/gain/offset
> > settings.
> 
> Yes, I will update the driver with that but as I told you in a previous
> mail, I can't test the suspend/resume :(

I wonder if Simon or Lothar or Franklin could help us with it (CCed). If
not, then we'll have to go by review only.

Thanks.

-- 
Dmitry