From mboxrd@z Thu Jan 1 00:00:00 1970 From: Chen-Yu Tsai Subject: [PATCH v2 6/6] [DO NOT MERGE] ARM: dts: sun7i: bananapi-m1-plus: Enable Bananapi 7" 800x480 RGB LCD panel Date: Fri, 7 Sep 2018 12:19:48 +0800 Message-ID: <20180907041948.19913-7-wens@csie.org> References: <20180907041948.19913-1-wens@csie.org> Reply-To: wens-jdAy2FN1RRM@public.gmane.org Mime-Version: 1.0 Content-Type: text/plain; charset="UTF-8" Return-path: Sender: linux-sunxi-/JYPxA39Uh5TLH3MbocFFw@public.gmane.org In-Reply-To: <20180907041948.19913-1-wens-jdAy2FN1RRM@public.gmane.org> List-Post: , List-Help: , List-Archive: , List-Unsubscribe: , To: Thierry Reding , David Airlie , Rob Herring , Mark Rutland , Maxime Ripard Cc: Chen-Yu Tsai , devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, dri-devel-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW@public.gmane.org, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org, linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-sunxi-/JYPxA39Uh5TLH3MbocFFw@public.gmane.org, Jonathan Liu List-Id: devicetree@vger.kernel.org The BPI-M1+ has an FPC connector for connecting an RGB (parallel) or LVDS LCD panel. One of the compatible panels is a 7" 800x480 RGB panel from Bananapi. The backlight can be controlled by driving a PWM signal from the SoC at different duty cycles. The LCD enable pin does not seem to do anything, but it is nevertheless included for completeness. There is also a FT5306 capacitive touchscreen controller. This should not be confused with the other 7" LCD that is LVDS based and has a resolution of 1024x600. This patch enables all of the above for the BPI-M1+. Signed-off-by: Chen-Yu Tsai --- .../boot/dts/sun7i-a20-bananapi-m1-plus.dts | 56 +++++++++++++++++++ 1 file changed, 56 insertions(+) diff --git a/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts b/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts index 763cb03033c4..9fa58adade56 100644 --- a/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts +++ b/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts @@ -47,6 +47,7 @@ #include "sunxi-common-regulators.dtsi" #include #include +#include / { model = "Banana Pi BPI-M1-Plus"; @@ -71,6 +72,29 @@ }; }; + lcd_backlight: lcd-backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 0 20000 PWM_POLARITY_INVERTED>; /* 50 kHz */ + enable-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */ + brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; + default-brightness-level = <8>; + }; + + lcd_panel: lcd-panel { + compatible = "bananapi,s070wv20-ct16", "simple-panel"; + power-supply = <®_vcc5v0>; /* Actually driven from IPSOUT */ + /* This doesn't do anything for this particular connector */ + enable-gpios = <&pio 7 12 GPIO_ACTIVE_HIGH>; /* PH12 */ + + port { + backlight = <&lcd_backlight>; + + lcd_panel_input: endpoint { + remote-endpoint = <&tcon0_out_lcd>; + }; + }; + }; + leds { compatible = "gpio-leds"; pinctrl-names = "default"; @@ -173,6 +197,20 @@ status = "okay"; }; +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_pins_a>; + status = "okay"; + + touchscreen@38 { + compatible = "edt,edt-ft5306", "edt,edt-ft5x06"; + reg = <0x38>; + interrupt-parent = <&pio>; + interrupts = <7 7 IRQ_TYPE_EDGE_FALLING>; /* PH7 */ + reset-gpios = <&pio 7 8 GPIO_ACTIVE_LOW>; /* PH8 */ + }; +}; + &ir0 { pinctrl-names = "default"; pinctrl-0 = <&ir0_rx_pins_a>; @@ -249,6 +287,12 @@ }; }; +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_pins_a>; + status = "okay"; +}; + ®_dcdc2 { regulator-always-on; regulator-min-microvolt = <1000000>; @@ -278,6 +322,18 @@ status = "okay"; }; +&tcon0 { + pinctrl-names = "default"; + pinctrl-0 = <&lcd0_rgb888_pins>; +}; + +&tcon0_out { + tcon0_out_lcd: endpoint@0 { + reg = <0>; + remote-endpoint = <&lcd_panel_input>; + }; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pins_a>; -- 2.19.0.rc1