* [PATCH v3 net-next 6/6] net: dsa: Add Lantiq / Intel DSA driver for vrx200
[not found] <20180909201647.32727-1-hauke@hauke-m.d>
2018-09-09 20:20 ` [PATCH v3 net-next 5/6] dt-bindings: net: dsa: Add lantiq,xrx200-gswip DT bindings Hauke Mehrtens
@ 2018-09-09 20:20 ` Hauke Mehrtens
2018-09-10 13:27 ` Andrew Lunn
1 sibling, 1 reply; 7+ messages in thread
From: Hauke Mehrtens @ 2018-09-09 20:20 UTC (permalink / raw)
To: davem
Cc: netdev, andrew, vivien.didelot, f.fainelli, john, linux-mips, dev,
hauke.mehrtens, devicetree
This adds the DSA driver for the GSWIP Switch found in the VRX200 SoC.
This switch is integrated in the DSL SoC, this SoC uses a GSWIP version
2.1, there are other SoCs using different versions of this IP block, but
this driver was only tested with the version found in the VRX200.
Currently only the basic features are implemented which will forward all
packages to the CPU and let the CPU do the forwarding. The hardware also
support Layer 2 offloading which is not yet implemented in this driver.
The GPHY FW loaded is now done by this driver and not any more by the
separate driver in drivers/soc/lantiq/gphy.c, I will remove this driver
is a separate patch. to make use of the GPHY this switch driver is
needed anyway. Other SoCs have more embedded GPHYs so this driver should
support a variable number of GPHYs. After the firmware was loaded the
GPHY can be probed on the MDIO bus and it behaves like an external GPHY,
without the firmware it can not be probed on the MDIO bus.
The clock names in the sysctrl.c file have to be changed because the
clocks are now used by a different driver. This should be cleaned up and
a real common clock driver should provide the clocks instead.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
---
MAINTAINERS | 2 +
arch/mips/lantiq/xway/sysctrl.c | 8 +-
drivers/net/dsa/Kconfig | 8 +
drivers/net/dsa/Makefile | 1 +
drivers/net/dsa/lantiq_gswip.c | 1169 +++++++++++++++++++++++++++++++++++++++
drivers/net/dsa/lantiq_pce.h | 153 +++++
6 files changed, 1337 insertions(+), 4 deletions(-)
create mode 100644 drivers/net/dsa/lantiq_gswip.c
create mode 100644 drivers/net/dsa/lantiq_pce.h
diff --git a/MAINTAINERS b/MAINTAINERS
index ffff912d31b5..5ae7385840e3 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -8172,6 +8172,8 @@ L: netdev@vger.kernel.org
S: Maintained
F: net/dsa/tag_gswip.c
F: drivers/net/ethernet/lantiq_xrx200.c
+F: drivers/net/dsa/lantiq_pce.h
+F: drivers/net/dsa/intel_gswip.c
LANTIQ MIPS ARCHITECTURE
M: John Crispin <john@phrozen.org>
diff --git a/arch/mips/lantiq/xway/sysctrl.c b/arch/mips/lantiq/xway/sysctrl.c
index eeb89a37e27e..fe25c99089b7 100644
--- a/arch/mips/lantiq/xway/sysctrl.c
+++ b/arch/mips/lantiq/xway/sysctrl.c
@@ -516,8 +516,8 @@ void __init ltq_soc_init(void)
clkdev_add_pmu("1e10b308.eth", NULL, 0, 0, PMU_SWITCH |
PMU_PPE_DP | PMU_PPE_TC);
clkdev_add_pmu("1da00000.usif", "NULL", 1, 0, PMU_USIF);
- clkdev_add_pmu("1f203020.gphy", NULL, 1, 0, PMU_GPHY);
- clkdev_add_pmu("1f203068.gphy", NULL, 1, 0, PMU_GPHY);
+ clkdev_add_pmu("1e108000.gswip", "gphy0", 0, 0, PMU_GPHY);
+ clkdev_add_pmu("1e108000.gswip", "gphy1", 0, 0, PMU_GPHY);
clkdev_add_pmu("1e103100.deu", NULL, 1, 0, PMU_DEU);
clkdev_add_pmu("1e116000.mei", "afe", 1, 2, PMU_ANALOG_DSL_AFE);
clkdev_add_pmu("1e116000.mei", "dfe", 1, 0, PMU_DFE);
@@ -540,8 +540,8 @@ void __init ltq_soc_init(void)
PMU_SWITCH | PMU_PPE_DPLUS | PMU_PPE_DPLUM |
PMU_PPE_EMA | PMU_PPE_TC | PMU_PPE_SLL01 |
PMU_PPE_QSB | PMU_PPE_TOP);
- clkdev_add_pmu("1f203020.gphy", NULL, 0, 0, PMU_GPHY);
- clkdev_add_pmu("1f203068.gphy", NULL, 0, 0, PMU_GPHY);
+ clkdev_add_pmu("1e108000.gswip", "gphy0", 0, 0, PMU_GPHY);
+ clkdev_add_pmu("1e108000.gswip", "gphy1", 0, 0, PMU_GPHY);
clkdev_add_pmu("1e103000.sdio", NULL, 1, 0, PMU_SDIO);
clkdev_add_pmu("1e103100.deu", NULL, 1, 0, PMU_DEU);
clkdev_add_pmu("1e116000.mei", "dfe", 1, 0, PMU_DFE);
diff --git a/drivers/net/dsa/Kconfig b/drivers/net/dsa/Kconfig
index d3ce1e4cb4d3..7c09d8f195ae 100644
--- a/drivers/net/dsa/Kconfig
+++ b/drivers/net/dsa/Kconfig
@@ -23,6 +23,14 @@ config NET_DSA_LOOP
This enables support for a fake mock-up switch chip which
exercises the DSA APIs.
+config NET_DSA_LANTIQ_GSWIP
+ tristate "Lantiq / Intel GSWIP"
+ depends on NET_DSA
+ select NET_DSA_TAG_GSWIP
+ ---help---
+ This enables support for the Lantiq / Intel GSWIP 2.1 found in
+ the xrx200 / VR9 SoC.
+
config NET_DSA_MT7530
tristate "Mediatek MT7530 Ethernet switch support"
depends on NET_DSA
diff --git a/drivers/net/dsa/Makefile b/drivers/net/dsa/Makefile
index 46c1cba91ffe..82e5d794c41f 100644
--- a/drivers/net/dsa/Makefile
+++ b/drivers/net/dsa/Makefile
@@ -5,6 +5,7 @@ obj-$(CONFIG_NET_DSA_LOOP) += dsa_loop.o
ifdef CONFIG_NET_DSA_LOOP
obj-$(CONFIG_FIXED_PHY) += dsa_loop_bdinfo.o
endif
+obj-$(CONFIG_NET_DSA_LANTIQ_GSWIP) += lantiq_gswip.o
obj-$(CONFIG_NET_DSA_MT7530) += mt7530.o
obj-$(CONFIG_NET_DSA_MV88E6060) += mv88e6060.o
obj-$(CONFIG_NET_DSA_QCA8K) += qca8k.o
diff --git a/drivers/net/dsa/lantiq_gswip.c b/drivers/net/dsa/lantiq_gswip.c
new file mode 100644
index 000000000000..9c28d0b2fcdb
--- /dev/null
+++ b/drivers/net/dsa/lantiq_gswip.c
@@ -0,0 +1,1169 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Lantiq / Intel GSWIP switch driver for VRX200 SoCs
+ *
+ * Copyright (C) 2010 Lantiq Deutschland
+ * Copyright (C) 2012 John Crispin <john@phrozen.org>
+ * Copyright (C) 2017 - 2018 Hauke Mehrtens <hauke@hauke-m.de>
+ */
+
+#include <linux/clk.h>
+#include <linux/etherdevice.h>
+#include <linux/firmware.h>
+#include <linux/if_bridge.h>
+#include <linux/if_vlan.h>
+#include <linux/iopoll.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_mdio.h>
+#include <linux/of_net.h>
+#include <linux/of_platform.h>
+#include <linux/phy.h>
+#include <linux/phylink.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <net/dsa.h>
+#include <dt-bindings/mips/lantiq_rcu_gphy.h>
+
+#include "lantiq_pce.h"
+
+/* GSWIP MDIO Registers */
+#define GSWIP_MDIO_GLOB 0x00
+#define GSWIP_MDIO_GLOB_ENABLE BIT(15)
+#define GSWIP_MDIO_CTRL 0x08
+#define GSWIP_MDIO_CTRL_BUSY BIT(12)
+#define GSWIP_MDIO_CTRL_RD BIT(11)
+#define GSWIP_MDIO_CTRL_WR BIT(10)
+#define GSWIP_MDIO_CTRL_PHYAD_MASK 0x1f
+#define GSWIP_MDIO_CTRL_PHYAD_SHIFT 5
+#define GSWIP_MDIO_CTRL_REGAD_MASK 0x1f
+#define GSWIP_MDIO_READ 0x09
+#define GSWIP_MDIO_WRITE 0x0A
+#define GSWIP_MDIO_MDC_CFG0 0x0B
+#define GSWIP_MDIO_MDC_CFG1 0x0C
+#define GSWIP_MDIO_PHYp(p) (0x15 - (p))
+#define GSWIP_MDIO_PHY_LINK_MASK 0x6000
+#define GSWIP_MDIO_PHY_LINK_AUTO 0x0000
+#define GSWIP_MDIO_PHY_LINK_DOWN 0x4000
+#define GSWIP_MDIO_PHY_LINK_UP 0x2000
+#define GSWIP_MDIO_PHY_SPEED_MASK 0x1800
+#define GSWIP_MDIO_PHY_SPEED_AUTO 0x1800
+#define GSWIP_MDIO_PHY_SPEED_M10 0x0000
+#define GSWIP_MDIO_PHY_SPEED_M100 0x0800
+#define GSWIP_MDIO_PHY_SPEED_G1 0x1000
+#define GSWIP_MDIO_PHY_FDUP_MASK 0x0600
+#define GSWIP_MDIO_PHY_FDUP_AUTO 0x0000
+#define GSWIP_MDIO_PHY_FDUP_EN 0x0200
+#define GSWIP_MDIO_PHY_FDUP_DIS 0x0600
+#define GSWIP_MDIO_PHY_FCONTX_MASK 0x0180
+#define GSWIP_MDIO_PHY_FCONTX_AUTO 0x0000
+#define GSWIP_MDIO_PHY_FCONTX_EN 0x0100
+#define GSWIP_MDIO_PHY_FCONTX_DIS 0x0180
+#define GSWIP_MDIO_PHY_FCONRX_MASK 0x0060
+#define GSWIP_MDIO_PHY_FCONRX_AUTO 0x0000
+#define GSWIP_MDIO_PHY_FCONRX_EN 0x0020
+#define GSWIP_MDIO_PHY_FCONRX_DIS 0x0060
+#define GSWIP_MDIO_PHY_ADDR_MASK 0x001f
+#define GSWIP_MDIO_PHY_MASK (GSWIP_MDIO_PHY_ADDR_MASK | \
+ GSWIP_MDIO_PHY_FCONRX_MASK | \
+ GSWIP_MDIO_PHY_FCONTX_MASK | \
+ GSWIP_MDIO_PHY_LINK_MASK | \
+ GSWIP_MDIO_PHY_SPEED_MASK | \
+ GSWIP_MDIO_PHY_FDUP_MASK)
+
+/* GSWIP MII Registers */
+#define GSWIP_MII_CFG0 0x00
+#define GSWIP_MII_CFG1 0x02
+#define GSWIP_MII_CFG5 0x04
+#define GSWIP_MII_CFG_EN BIT(14)
+#define GSWIP_MII_CFG_LDCLKDIS BIT(12)
+#define GSWIP_MII_CFG_MODE_MIIP 0x0
+#define GSWIP_MII_CFG_MODE_MIIM 0x1
+#define GSWIP_MII_CFG_MODE_RMIIP 0x2
+#define GSWIP_MII_CFG_MODE_RMIIM 0x3
+#define GSWIP_MII_CFG_MODE_RGMII 0x4
+#define GSWIP_MII_CFG_MODE_MASK 0xf
+#define GSWIP_MII_CFG_RATE_M2P5 0x00
+#define GSWIP_MII_CFG_RATE_M25 0x10
+#define GSWIP_MII_CFG_RATE_M125 0x20
+#define GSWIP_MII_CFG_RATE_M50 0x30
+#define GSWIP_MII_CFG_RATE_AUTO 0x40
+#define GSWIP_MII_CFG_RATE_MASK 0x70
+#define GSWIP_MII_PCDU0 0x01
+#define GSWIP_MII_PCDU1 0x03
+#define GSWIP_MII_PCDU5 0x05
+#define GSWIP_MII_PCDU_TXDLY_MASK GENMASK(2, 0)
+#define GSWIP_MII_PCDU_RXDLY_MASK GENMASK(9, 7)
+
+/* GSWIP Core Registers */
+#define GSWIP_SWRES 0x000
+#define GSWIP_SWRES_R1 BIT(1) /* GSWIP Software reset */
+#define GSWIP_SWRES_R0 BIT(0) /* GSWIP Hardware reset */
+#define GSWIP_VERSION 0x013
+#define GSWIP_VERSION_REV_SHIFT 0
+#define GSWIP_VERSION_REV_MASK GENMASK(7, 0)
+#define GSWIP_VERSION_MOD_SHIFT 8
+#define GSWIP_VERSION_MOD_MASK GENMASK(15, 8)
+#define GSWIP_VERSION_2_0 0x100
+#define GSWIP_VERSION_2_1 0x021
+#define GSWIP_VERSION_2_2 0x122
+#define GSWIP_VERSION_2_2_ETC 0x022
+
+#define GSWIP_BM_RAM_VAL(x) (0x043 - (x))
+#define GSWIP_BM_RAM_ADDR 0x044
+#define GSWIP_BM_RAM_CTRL 0x045
+#define GSWIP_BM_RAM_CTRL_BAS BIT(15)
+#define GSWIP_BM_RAM_CTRL_OPMOD BIT(5)
+#define GSWIP_BM_RAM_CTRL_ADDR_MASK GENMASK(4, 0)
+#define GSWIP_BM_QUEUE_GCTRL 0x04A
+#define GSWIP_BM_QUEUE_GCTRL_GL_MOD BIT(10)
+/* buffer management Port Configuration Register */
+#define GSWIP_BM_PCFGp(p) (0x080 + ((p) * 2))
+#define GSWIP_BM_PCFG_CNTEN BIT(0) /* RMON Counter Enable */
+#define GSWIP_BM_PCFG_IGCNT BIT(1) /* Ingres Special Tag RMON count */
+/* buffer management Port Control Register */
+#define GSWIP_BM_RMON_CTRLp(p) (0x81 + ((p) * 2))
+#define GSWIP_BM_CTRL_RMON_RAM1_RES BIT(0) /* Software Reset for RMON RAM 1 */
+#define GSWIP_BM_CTRL_RMON_RAM2_RES BIT(1) /* Software Reset for RMON RAM 2 */
+
+/* PCE */
+#define GSWIP_PCE_TBL_KEY(x) (0x447 - (x))
+#define GSWIP_PCE_TBL_MASK 0x448
+#define GSWIP_PCE_TBL_VAL(x) (0x44D - (x))
+#define GSWIP_PCE_TBL_ADDR 0x44E
+#define GSWIP_PCE_TBL_CTRL 0x44F
+#define GSWIP_PCE_TBL_CTRL_BAS BIT(15)
+#define GSWIP_PCE_TBL_CTRL_TYPE BIT(13)
+#define GSWIP_PCE_TBL_CTRL_VLD BIT(12)
+#define GSWIP_PCE_TBL_CTRL_KEYFORM BIT(11)
+#define GSWIP_PCE_TBL_CTRL_GMAP_MASK GENMASK(10, 7)
+#define GSWIP_PCE_TBL_CTRL_OPMOD_MASK GENMASK(6, 5)
+#define GSWIP_PCE_TBL_CTRL_OPMOD_ADRD 0x00
+#define GSWIP_PCE_TBL_CTRL_OPMOD_ADWR 0x20
+#define GSWIP_PCE_TBL_CTRL_OPMOD_KSRD 0x40
+#define GSWIP_PCE_TBL_CTRL_OPMOD_KSWR 0x60
+#define GSWIP_PCE_TBL_CTRL_ADDR_MASK GENMASK(4, 0)
+#define GSWIP_PCE_PMAP1 0x453 /* Monitoring port map */
+#define GSWIP_PCE_PMAP2 0x454 /* Default Multicast port map */
+#define GSWIP_PCE_PMAP3 0x455 /* Default Unknown Unicast port map */
+#define GSWIP_PCE_GCTRL_0 0x456
+#define GSWIP_PCE_GCTRL_0_MC_VALID BIT(3)
+#define GSWIP_PCE_GCTRL_0_VLAN BIT(14) /* VLAN aware Switching */
+#define GSWIP_PCE_GCTRL_1 0x457
+#define GSWIP_PCE_GCTRL_1_MAC_GLOCK BIT(2) /* MAC Address table lock */
+#define GSWIP_PCE_GCTRL_1_MAC_GLOCK_MOD BIT(3) /* Mac address table lock forwarding mode */
+#define GSWIP_PCE_PCTRL_0p(p) (0x480 + ((p) * 0xA))
+#define GSWIP_PCE_PCTRL_0_INGRESS BIT(11)
+#define GSWIP_PCE_PCTRL_0_PSTATE_LISTEN 0x0
+#define GSWIP_PCE_PCTRL_0_PSTATE_RX 0x1
+#define GSWIP_PCE_PCTRL_0_PSTATE_TX 0x2
+#define GSWIP_PCE_PCTRL_0_PSTATE_LEARNING 0x3
+#define GSWIP_PCE_PCTRL_0_PSTATE_FORWARDING 0x7
+#define GSWIP_PCE_PCTRL_0_PSTATE_MASK GENMASK(2, 0)
+
+#define GSWIP_MAC_FLEN 0x8C5
+#define GSWIP_MAC_CTRL_2p(p) (0x905 + ((p) * 0xC))
+#define GSWIP_MAC_CTRL_2_MLEN BIT(3) /* Maximum Untagged Frame Lnegth */
+
+/* Ethernet Switch Fetch DMA Port Control Register */
+#define GSWIP_FDMA_PCTRLp(p) (0xA80 + ((p) * 0x6))
+#define GSWIP_FDMA_PCTRL_EN BIT(0) /* FDMA Port Enable */
+#define GSWIP_FDMA_PCTRL_STEN BIT(1) /* Special Tag Insertion Enable */
+#define GSWIP_FDMA_PCTRL_VLANMOD_MASK GENMASK(4, 3) /* VLAN Modification Control */
+#define GSWIP_FDMA_PCTRL_VLANMOD_SHIFT 3 /* VLAN Modification Control */
+#define GSWIP_FDMA_PCTRL_VLANMOD_DIS (0x0 << GSWIP_FDMA_PCTRL_VLANMOD_SHIFT)
+#define GSWIP_FDMA_PCTRL_VLANMOD_PRIO (0x1 << GSWIP_FDMA_PCTRL_VLANMOD_SHIFT)
+#define GSWIP_FDMA_PCTRL_VLANMOD_ID (0x2 << GSWIP_FDMA_PCTRL_VLANMOD_SHIFT)
+#define GSWIP_FDMA_PCTRL_VLANMOD_BOTH (0x3 << GSWIP_FDMA_PCTRL_VLANMOD_SHIFT)
+
+/* Ethernet Switch Store DMA Port Control Register */
+#define GSWIP_SDMA_PCTRLp(p) (0xBC0 + ((p) * 0x6))
+#define GSWIP_SDMA_PCTRL_EN BIT(0) /* SDMA Port Enable */
+#define GSWIP_SDMA_PCTRL_FCEN BIT(1) /* Flow Control Enable */
+#define GSWIP_SDMA_PCTRL_PAUFWD BIT(1) /* Pause Frame Forwarding */
+
+#define XRX200_GPHY_FW_ALIGN (16 * 1024)
+
+struct gswip_hw_info {
+ int max_ports;
+ int cpu_port;
+};
+
+struct xway_gphy_match_data {
+ char *fe_firmware_name;
+ char *ge_firmware_name;
+};
+
+struct gswip_gphy_fw {
+ struct clk *clk_gate;
+ struct reset_control *reset;
+ u32 fw_addr_offset;
+ char *fw_name;
+};
+
+struct gswip_priv {
+ __iomem void *gswip;
+ __iomem void *mdio;
+ __iomem void *mii;
+ const struct gswip_hw_info *hw_info;
+ const struct xway_gphy_match_data *gphy_fw_name_cfg;
+ struct dsa_switch *ds;
+ struct device *dev;
+ struct regmap *rcu_regmap;
+ int num_gphy_fw;
+ struct gswip_gphy_fw *gphy_fw;
+};
+
+struct gswip_rmon_cnt_desc {
+ unsigned int size;
+ unsigned int offset;
+ const char *name;
+};
+
+#define MIB_DESC(_size, _offset, _name) {.size = _size, .offset = _offset, .name = _name}
+
+static const struct gswip_rmon_cnt_desc gswip_rmon_cnt[] = {
+ /** Receive Packet Count (only packets that are accepted and not discarded). */
+ MIB_DESC(1, 0x1F, "RxGoodPkts"),
+ MIB_DESC(1, 0x23, "RxUnicastPkts"),
+ MIB_DESC(1, 0x22, "RxMulticastPkts"),
+ MIB_DESC(1, 0x21, "RxFCSErrorPkts"),
+ MIB_DESC(1, 0x1D, "RxUnderSizeGoodPkts"),
+ MIB_DESC(1, 0x1E, "RxUnderSizeErrorPkts"),
+ MIB_DESC(1, 0x1B, "RxOversizeGoodPkts"),
+ MIB_DESC(1, 0x1C, "RxOversizeErrorPkts"),
+ MIB_DESC(1, 0x20, "RxGoodPausePkts"),
+ MIB_DESC(1, 0x1A, "RxAlignErrorPkts"),
+ MIB_DESC(1, 0x12, "Rx64BytePkts"),
+ MIB_DESC(1, 0x13, "Rx127BytePkts"),
+ MIB_DESC(1, 0x14, "Rx255BytePkts"),
+ MIB_DESC(1, 0x15, "Rx511BytePkts"),
+ MIB_DESC(1, 0x16, "Rx1023BytePkts"),
+ /** Receive Size 1024-1522 (or more, if configured) Packet Count. */
+ MIB_DESC(1, 0x17, "RxMaxBytePkts"),
+ MIB_DESC(1, 0x18, "RxDroppedPkts"),
+ MIB_DESC(1, 0x19, "RxFilteredPkts"),
+ MIB_DESC(2, 0x24, "RxGoodBytes"),
+ MIB_DESC(2, 0x26, "RxBadBytes"),
+ MIB_DESC(1, 0x11, "TxAcmDroppedPkts"),
+ MIB_DESC(1, 0x0C, "TxGoodPkts"),
+ MIB_DESC(1, 0x06, "TxUnicastPkts"),
+ MIB_DESC(1, 0x07, "TxMulticastPkts"),
+ MIB_DESC(1, 0x00, "Tx64BytePkts"),
+ MIB_DESC(1, 0x01, "Tx127BytePkts"),
+ MIB_DESC(1, 0x02, "Tx255BytePkts"),
+ MIB_DESC(1, 0x03, "Tx511BytePkts"),
+ MIB_DESC(1, 0x04, "Tx1023BytePkts"),
+ /** Transmit Size 1024-1522 (or more, if configured) Packet Count. */
+ MIB_DESC(1, 0x05, "TxMaxBytePkts"),
+ MIB_DESC(1, 0x08, "TxSingleCollCount"),
+ MIB_DESC(1, 0x09, "TxMultCollCount"),
+ MIB_DESC(1, 0x0A, "TxLateCollCount"),
+ MIB_DESC(1, 0x0B, "TxExcessCollCount"),
+ MIB_DESC(1, 0x0D, "TxPauseCount"),
+ MIB_DESC(1, 0x10, "TxDroppedPkts"),
+ MIB_DESC(2, 0x0E, "TxGoodBytes"),
+};
+
+static u32 gswip_switch_r(struct gswip_priv *priv, u32 offset)
+{
+ return __raw_readl(priv->gswip + (offset * 4));
+}
+
+static void gswip_switch_w(struct gswip_priv *priv, u32 val, u32 offset)
+{
+ __raw_writel(val, priv->gswip + (offset * 4));
+}
+
+static void gswip_switch_mask(struct gswip_priv *priv, u32 clear, u32 set,
+ u32 offset)
+{
+ u32 val = gswip_switch_r(priv, offset);
+
+ val &= ~(clear);
+ val |= set;
+ gswip_switch_w(priv, val, offset);
+}
+
+static u32 gswip_switch_r_timeout(struct gswip_priv *priv, u32 offset,
+ u32 cleared)
+{
+ u32 val;
+
+ return readx_poll_timeout(__raw_readl, priv->gswip + (offset * 4), val,
+ (val & cleared) == 0, 20, 50000);
+}
+
+static u32 gswip_mdio_r(struct gswip_priv *priv, u32 offset)
+{
+ return __raw_readl(priv->mdio + (offset * 4));
+}
+
+static void gswip_mdio_w(struct gswip_priv *priv, u32 val, u32 offset)
+{
+ __raw_writel(val, priv->mdio + (offset * 4));
+}
+
+static void gswip_mdio_mask(struct gswip_priv *priv, u32 clear, u32 set,
+ u32 offset)
+{
+ u32 val = gswip_mdio_r(priv, offset);
+
+ val &= ~(clear);
+ val |= set;
+ gswip_mdio_w(priv, val, offset);
+}
+
+static u32 gswip_mii_r(struct gswip_priv *priv, u32 offset)
+{
+ return __raw_readl(priv->mii + (offset * 4));
+}
+
+static void gswip_mii_w(struct gswip_priv *priv, u32 val, u32 offset)
+{
+ __raw_writel(val, priv->mii + (offset * 4));
+}
+
+static void gswip_mii_mask(struct gswip_priv *priv, u32 clear, u32 set,
+ u32 offset)
+{
+ u32 val = gswip_mii_r(priv, offset);
+
+ val &= ~(clear);
+ val |= set;
+ gswip_mii_w(priv, val, offset);
+}
+
+static void gswip_mii_mask_cfg(struct gswip_priv *priv, u32 clear, u32 set,
+ int port)
+{
+ switch (port) {
+ case 0:
+ gswip_mii_mask(priv, clear, set, GSWIP_MII_CFG0);
+ break;
+ case 1:
+ gswip_mii_mask(priv, clear, set, GSWIP_MII_CFG1);
+ break;
+ case 5:
+ gswip_mii_mask(priv, clear, set, GSWIP_MII_CFG5);
+ break;
+ }
+}
+
+static void gswip_mii_mask_pcdu(struct gswip_priv *priv, u32 clear, u32 set,
+ int port)
+{
+ switch (port) {
+ case 0:
+ gswip_mii_mask(priv, clear, set, GSWIP_MII_PCDU0);
+ break;
+ case 1:
+ gswip_mii_mask(priv, clear, set, GSWIP_MII_PCDU1);
+ break;
+ case 5:
+ gswip_mii_mask(priv, clear, set, GSWIP_MII_PCDU5);
+ break;
+ }
+}
+
+static int gswip_mdio_poll(struct gswip_priv *priv)
+{
+ int cnt = 100;
+
+ while (likely(cnt--)) {
+ u32 ctrl = gswip_mdio_r(priv, GSWIP_MDIO_CTRL);
+
+ if ((ctrl & GSWIP_MDIO_CTRL_BUSY) == 0)
+ return 0;
+ usleep_range(20, 40);
+ }
+
+ return -ETIMEDOUT;
+}
+
+static int gswip_mdio_wr(struct mii_bus *bus, int addr, int reg, u16 val)
+{
+ struct gswip_priv *priv = bus->priv;
+ int err;
+
+ err = gswip_mdio_poll(priv);
+ if (err) {
+ dev_err(&bus->dev, "waiting for MDIO bus busy timed out\n");
+ return err;
+ }
+
+ gswip_mdio_w(priv, val, GSWIP_MDIO_WRITE);
+ gswip_mdio_w(priv, GSWIP_MDIO_CTRL_BUSY | GSWIP_MDIO_CTRL_WR |
+ ((addr & GSWIP_MDIO_CTRL_PHYAD_MASK) << GSWIP_MDIO_CTRL_PHYAD_SHIFT) |
+ (reg & GSWIP_MDIO_CTRL_REGAD_MASK),
+ GSWIP_MDIO_CTRL);
+
+ return 0;
+}
+
+static int gswip_mdio_rd(struct mii_bus *bus, int addr, int reg)
+{
+ struct gswip_priv *priv = bus->priv;
+ int err;
+
+ err = gswip_mdio_poll(priv);
+ if (err) {
+ dev_err(&bus->dev, "waiting for MDIO bus busy timed out\n");
+ return err;
+ }
+
+ gswip_mdio_w(priv, GSWIP_MDIO_CTRL_BUSY | GSWIP_MDIO_CTRL_RD |
+ ((addr & GSWIP_MDIO_CTRL_PHYAD_MASK) << GSWIP_MDIO_CTRL_PHYAD_SHIFT) |
+ (reg & GSWIP_MDIO_CTRL_REGAD_MASK),
+ GSWIP_MDIO_CTRL);
+
+ err = gswip_mdio_poll(priv);
+ if (err) {
+ dev_err(&bus->dev, "waiting for MDIO bus busy timed out\n");
+ return err;
+ }
+
+ return gswip_mdio_r(priv, GSWIP_MDIO_READ);
+}
+
+static int gswip_mdio(struct gswip_priv *priv, struct device_node *mdio_np)
+{
+ struct dsa_switch *ds = priv->ds;
+
+ ds->slave_mii_bus = devm_mdiobus_alloc(priv->dev);
+ if (!ds->slave_mii_bus)
+ return -ENOMEM;
+
+ ds->slave_mii_bus->priv = priv;
+ ds->slave_mii_bus->read = gswip_mdio_rd;
+ ds->slave_mii_bus->write = gswip_mdio_wr;
+ ds->slave_mii_bus->name = "lantiq,xrx200-mdio";
+ snprintf(ds->slave_mii_bus->id, MII_BUS_ID_SIZE, "%s-mii",
+ dev_name(priv->dev));
+ ds->slave_mii_bus->parent = priv->dev;
+ ds->slave_mii_bus->phy_mask = ~ds->phys_mii_mask;
+
+ return of_mdiobus_register(ds->slave_mii_bus, mdio_np);
+}
+
+static int gswip_port_enable(struct dsa_switch *ds, int port,
+ struct phy_device *phydev)
+{
+ struct gswip_priv *priv = ds->priv;
+
+ /* RMON Counter Enable for port */
+ gswip_switch_w(priv, GSWIP_BM_PCFG_CNTEN, GSWIP_BM_PCFGp(port));
+
+ /* enable port fetch/store dma & VLAN Modification */
+ gswip_switch_mask(priv, 0, GSWIP_FDMA_PCTRL_EN |
+ GSWIP_FDMA_PCTRL_VLANMOD_BOTH,
+ GSWIP_FDMA_PCTRLp(port));
+ gswip_switch_mask(priv, 0, GSWIP_SDMA_PCTRL_EN,
+ GSWIP_SDMA_PCTRLp(port));
+ gswip_switch_mask(priv, 0, GSWIP_PCE_PCTRL_0_INGRESS,
+ GSWIP_PCE_PCTRL_0p(port));
+
+ if (!dsa_is_cpu_port(ds, port)) {
+ u32 macconf = GSWIP_MDIO_PHY_LINK_AUTO |
+ GSWIP_MDIO_PHY_SPEED_AUTO |
+ GSWIP_MDIO_PHY_FDUP_AUTO |
+ GSWIP_MDIO_PHY_FCONTX_AUTO |
+ GSWIP_MDIO_PHY_FCONRX_AUTO |
+ (phydev->mdio.addr & GSWIP_MDIO_PHY_ADDR_MASK);
+
+ gswip_mdio_w(priv, macconf, GSWIP_MDIO_PHYp(port));
+ /* Activate MDIO auto polling */
+ gswip_mdio_mask(priv, 0, BIT(port), GSWIP_MDIO_MDC_CFG0);
+ }
+
+ return 0;
+}
+
+static void gswip_port_disable(struct dsa_switch *ds, int port,
+ struct phy_device *phy)
+{
+ struct gswip_priv *priv = ds->priv;
+
+ if (!dsa_is_cpu_port(ds, port)) {
+ gswip_mdio_mask(priv, GSWIP_MDIO_PHY_LINK_DOWN,
+ GSWIP_MDIO_PHY_LINK_MASK,
+ GSWIP_MDIO_PHYp(port));
+ /* Deactivate MDIO auto polling */
+ gswip_mdio_mask(priv, BIT(port), 0, GSWIP_MDIO_MDC_CFG0);
+ }
+
+ gswip_switch_mask(priv, GSWIP_FDMA_PCTRL_EN, 0,
+ GSWIP_FDMA_PCTRLp(port));
+ gswip_switch_mask(priv, GSWIP_SDMA_PCTRL_EN, 0,
+ GSWIP_SDMA_PCTRLp(port));
+}
+
+static int gswip_pce_load_microcode(struct gswip_priv *priv)
+{
+ int i;
+ int err;
+
+ gswip_switch_mask(priv, GSWIP_PCE_TBL_CTRL_ADDR_MASK |
+ GSWIP_PCE_TBL_CTRL_OPMOD_MASK,
+ GSWIP_PCE_TBL_CTRL_OPMOD_ADWR, GSWIP_PCE_TBL_CTRL);
+ gswip_switch_w(priv, 0, GSWIP_PCE_TBL_MASK);
+
+ for (i = 0; i < ARRAY_SIZE(gswip_pce_microcode); i++) {
+ gswip_switch_w(priv, i, GSWIP_PCE_TBL_ADDR);
+ gswip_switch_w(priv, gswip_pce_microcode[i].val_0,
+ GSWIP_PCE_TBL_VAL(0));
+ gswip_switch_w(priv, gswip_pce_microcode[i].val_1,
+ GSWIP_PCE_TBL_VAL(1));
+ gswip_switch_w(priv, gswip_pce_microcode[i].val_2,
+ GSWIP_PCE_TBL_VAL(2));
+ gswip_switch_w(priv, gswip_pce_microcode[i].val_3,
+ GSWIP_PCE_TBL_VAL(3));
+
+ /* start the table access: */
+ gswip_switch_mask(priv, 0, GSWIP_PCE_TBL_CTRL_BAS,
+ GSWIP_PCE_TBL_CTRL);
+ err = gswip_switch_r_timeout(priv, GSWIP_PCE_TBL_CTRL,
+ GSWIP_PCE_TBL_CTRL_BAS);
+ if (err)
+ return err;
+ }
+
+ /* tell the switch that the microcode is loaded */
+ gswip_switch_mask(priv, 0, GSWIP_PCE_GCTRL_0_MC_VALID,
+ GSWIP_PCE_GCTRL_0);
+
+ return 0;
+}
+
+static int gswip_setup(struct dsa_switch *ds)
+{
+ struct gswip_priv *priv = ds->priv;
+ unsigned int cpu_port = priv->hw_info->cpu_port;
+ int i;
+ int err;
+
+ gswip_switch_w(priv, GSWIP_SWRES_R0, GSWIP_SWRES);
+ usleep_range(5000, 10000);
+ gswip_switch_w(priv, 0, GSWIP_SWRES);
+
+ /* disable port fetch/store dma on all ports */
+ for (i = 0; i < priv->hw_info->max_ports; i++)
+ gswip_port_disable(ds, i, NULL);
+
+ /* enable Switch */
+ gswip_mdio_mask(priv, 0, GSWIP_MDIO_GLOB_ENABLE, GSWIP_MDIO_GLOB);
+
+ err = gswip_pce_load_microcode(priv);
+ if (err) {
+ dev_err(priv->dev, "writing PCE microcode failed, %i", err);
+ return err;
+ }
+
+ /* Default unknown Broadcast/Multicast/Unicast port maps */
+ gswip_switch_w(priv, BIT(cpu_port), GSWIP_PCE_PMAP1);
+ gswip_switch_w(priv, BIT(cpu_port), GSWIP_PCE_PMAP2);
+ gswip_switch_w(priv, BIT(cpu_port), GSWIP_PCE_PMAP3);
+
+ /* disable PHY auto polling */
+ gswip_mdio_w(priv, 0x0, GSWIP_MDIO_MDC_CFG0);
+ /* Configure the MDIO Clock 2.5 MHz */
+ gswip_mdio_mask(priv, 0xff, 0x09, GSWIP_MDIO_MDC_CFG1);
+
+ /* Disable the xMII link */
+ gswip_mii_mask_cfg(priv, GSWIP_MII_CFG_EN, 0, 0);
+ gswip_mii_mask_cfg(priv, GSWIP_MII_CFG_EN, 0, 1);
+ gswip_mii_mask_cfg(priv, GSWIP_MII_CFG_EN, 0, 5);
+
+ /* enable special tag insertion on cpu port */
+ gswip_switch_mask(priv, 0, GSWIP_FDMA_PCTRL_STEN,
+ GSWIP_FDMA_PCTRLp(cpu_port));
+
+ gswip_switch_mask(priv, 0, GSWIP_MAC_CTRL_2_MLEN,
+ GSWIP_MAC_CTRL_2p(cpu_port));
+ gswip_switch_w(priv, VLAN_ETH_FRAME_LEN + 8, GSWIP_MAC_FLEN);
+ gswip_switch_mask(priv, 0, GSWIP_BM_QUEUE_GCTRL_GL_MOD,
+ GSWIP_BM_QUEUE_GCTRL);
+
+ /* VLAN aware Switching */
+ gswip_switch_mask(priv, 0, GSWIP_PCE_GCTRL_0_VLAN, GSWIP_PCE_GCTRL_0);
+
+ /* Mac Address Table Lock */
+ gswip_switch_mask(priv, 0, GSWIP_PCE_GCTRL_1_MAC_GLOCK |
+ GSWIP_PCE_GCTRL_1_MAC_GLOCK_MOD,
+ GSWIP_PCE_GCTRL_1);
+
+ gswip_port_enable(ds, cpu_port, NULL);
+ return 0;
+}
+
+static enum dsa_tag_protocol gswip_get_tag_protocol(struct dsa_switch *ds,
+ int port)
+{
+ return DSA_TAG_PROTO_GSWIP;
+}
+
+static void gswip_phylink_validate(struct dsa_switch *ds, int port,
+ unsigned long *supported,
+ struct phylink_link_state *state)
+{
+ __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
+
+ switch (port) {
+ case 0:
+ case 1:
+ if (!phy_interface_mode_is_rgmii(state->interface) &&
+ state->interface != PHY_INTERFACE_MODE_MII &&
+ state->interface != PHY_INTERFACE_MODE_REVMII &&
+ state->interface != PHY_INTERFACE_MODE_RMII) {
+ bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
+ dev_err(ds->dev,
+ "Unsupported interface: %d\n", state->interface);
+ return;
+ }
+ break;
+ case 2:
+ case 3:
+ case 4:
+ if (state->interface != PHY_INTERFACE_MODE_INTERNAL) {
+ bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
+ dev_err(ds->dev,
+ "Unsupported interface: %d\n", state->interface);
+ return;
+ }
+ break;
+ case 5:
+ if (!phy_interface_mode_is_rgmii(state->interface) &&
+ state->interface != PHY_INTERFACE_MODE_INTERNAL) {
+ bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
+ dev_err(ds->dev,
+ "Unsupported interface: %d\n", state->interface);
+ return;
+ }
+ break;
+ }
+
+ /* Allow all the expected bits */
+ phylink_set(mask, Autoneg);
+ phylink_set_port_modes(mask);
+ phylink_set(mask, Pause);
+ phylink_set(mask, Asym_Pause);
+
+ /* With the exclusion of MII and Reverse MII, we support Gigabit,
+ * including Half duplex
+ */
+ if (state->interface != PHY_INTERFACE_MODE_MII &&
+ state->interface != PHY_INTERFACE_MODE_REVMII) {
+ phylink_set(mask, 1000baseT_Full);
+ phylink_set(mask, 1000baseT_Half);
+ }
+
+ phylink_set(mask, 10baseT_Half);
+ phylink_set(mask, 10baseT_Full);
+ phylink_set(mask, 100baseT_Half);
+ phylink_set(mask, 100baseT_Full);
+
+ bitmap_and(supported, supported, mask,
+ __ETHTOOL_LINK_MODE_MASK_NBITS);
+ bitmap_and(state->advertising, state->advertising, mask,
+ __ETHTOOL_LINK_MODE_MASK_NBITS);
+}
+
+static void gswip_phylink_mac_config(struct dsa_switch *ds, int port,
+ unsigned int mode,
+ const struct phylink_link_state *state)
+{
+ struct gswip_priv *priv = ds->priv;
+ u32 miicfg = 0;
+
+ miicfg |= GSWIP_MII_CFG_LDCLKDIS;
+
+ switch (state->interface) {
+ case PHY_INTERFACE_MODE_MII:
+ case PHY_INTERFACE_MODE_INTERNAL:
+ miicfg |= GSWIP_MII_CFG_MODE_MIIM;
+ break;
+ case PHY_INTERFACE_MODE_REVMII:
+ miicfg |= GSWIP_MII_CFG_MODE_MIIP;
+ break;
+ case PHY_INTERFACE_MODE_RMII:
+ miicfg |= GSWIP_MII_CFG_MODE_RMIIM;
+ break;
+ case PHY_INTERFACE_MODE_RGMII:
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ miicfg |= GSWIP_MII_CFG_MODE_RGMII;
+ break;
+ default:
+ dev_err(ds->dev,
+ "Unsupported interface: %d\n", state->interface);
+ return;
+ }
+ gswip_mii_mask_cfg(priv, GSWIP_MII_CFG_MODE_MASK, miicfg, port);
+
+ switch (state->interface) {
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ gswip_mii_mask_pcdu(priv, GSWIP_MII_PCDU_TXDLY_MASK |
+ GSWIP_MII_PCDU_RXDLY_MASK, 0, port);
+ break;
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ gswip_mii_mask_pcdu(priv, GSWIP_MII_PCDU_RXDLY_MASK, 0, port);
+ break;
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ gswip_mii_mask_pcdu(priv, GSWIP_MII_PCDU_TXDLY_MASK, 0, port);
+ break;
+ default:
+ break;
+ }
+}
+
+static void gswip_phylink_mac_link_down(struct dsa_switch *ds, int port,
+ unsigned int mode,
+ phy_interface_t interface)
+{
+ struct gswip_priv *priv = ds->priv;
+
+ gswip_mii_mask_cfg(priv, GSWIP_MII_CFG_EN, 0, port);
+}
+
+static void gswip_phylink_mac_link_up(struct dsa_switch *ds, int port,
+ unsigned int mode,
+ phy_interface_t interface,
+ struct phy_device *phydev)
+{
+ struct gswip_priv *priv = ds->priv;
+
+ /* Enable the xMII interface only for the external PHY */
+ if (interface != PHY_INTERFACE_MODE_INTERNAL)
+ gswip_mii_mask_cfg(priv, 0, GSWIP_MII_CFG_EN, port);
+}
+
+static void gswip_get_strings(struct dsa_switch *ds, int port, u32 stringset,
+ uint8_t *data)
+{
+ int i;
+
+ if (stringset != ETH_SS_STATS)
+ return;
+
+ for (i = 0; i < ARRAY_SIZE(gswip_rmon_cnt); i++)
+ strncpy(data + i * ETH_GSTRING_LEN, gswip_rmon_cnt[i].name,
+ ETH_GSTRING_LEN);
+}
+
+static u32 gswip_bcm_ram_entry_read(struct gswip_priv *priv, u32 table,
+ u32 index)
+{
+ u32 result;
+ int err;
+
+ gswip_switch_w(priv, index, GSWIP_BM_RAM_ADDR);
+ gswip_switch_mask(priv, GSWIP_BM_RAM_CTRL_ADDR_MASK |
+ GSWIP_BM_RAM_CTRL_OPMOD,
+ table | GSWIP_BM_RAM_CTRL_BAS,
+ GSWIP_BM_RAM_CTRL);
+
+ err = gswip_switch_r_timeout(priv, GSWIP_BM_RAM_CTRL,
+ GSWIP_BM_RAM_CTRL_BAS);
+ if (err) {
+ dev_err(priv->dev, "timeout while reading table: %u, index: %u",
+ table, index);
+ return 0;
+ }
+
+ result = gswip_switch_r(priv, GSWIP_BM_RAM_VAL(0));
+ result |= gswip_switch_r(priv, GSWIP_BM_RAM_VAL(1)) << 16;
+
+ return result;
+}
+
+static void gswip_get_ethtool_stats(struct dsa_switch *ds, int port,
+ uint64_t *data)
+{
+ struct gswip_priv *priv = ds->priv;
+ const struct gswip_rmon_cnt_desc *rmon_cnt;
+ int i;
+ u64 high;
+
+ for (i = 0; i < ARRAY_SIZE(gswip_rmon_cnt); i++) {
+ rmon_cnt = &gswip_rmon_cnt[i];
+
+ data[i] = gswip_bcm_ram_entry_read(priv, port,
+ rmon_cnt->offset);
+ if (rmon_cnt->size == 2) {
+ high = gswip_bcm_ram_entry_read(priv, port,
+ rmon_cnt->offset + 1);
+ data[i] |= high << 32;
+ }
+ }
+}
+
+static int gswip_get_sset_count(struct dsa_switch *ds, int port, int sset)
+{
+ if (sset != ETH_SS_STATS)
+ return 0;
+
+ return ARRAY_SIZE(gswip_rmon_cnt);
+}
+
+static const struct dsa_switch_ops gswip_switch_ops = {
+ .get_tag_protocol = gswip_get_tag_protocol,
+ .setup = gswip_setup,
+ .port_enable = gswip_port_enable,
+ .port_disable = gswip_port_disable,
+ .phylink_validate = gswip_phylink_validate,
+ .phylink_mac_config = gswip_phylink_mac_config,
+ .phylink_mac_link_down = gswip_phylink_mac_link_down,
+ .phylink_mac_link_up = gswip_phylink_mac_link_up,
+ .get_strings = gswip_get_strings,
+ .get_ethtool_stats = gswip_get_ethtool_stats,
+ .get_sset_count = gswip_get_sset_count,
+};
+
+static const struct xway_gphy_match_data xrx200a1x_gphy_data = {
+ .fe_firmware_name = "lantiq/xrx200_phy22f_a14.bin",
+ .ge_firmware_name = "lantiq/xrx200_phy11g_a14.bin",
+};
+
+static const struct xway_gphy_match_data xrx200a2x_gphy_data = {
+ .fe_firmware_name = "lantiq/xrx200_phy22f_a22.bin",
+ .ge_firmware_name = "lantiq/xrx200_phy11g_a22.bin",
+};
+
+static const struct xway_gphy_match_data xrx300_gphy_data = {
+ .fe_firmware_name = "lantiq/xrx300_phy22f_a21.bin",
+ .ge_firmware_name = "lantiq/xrx300_phy11g_a21.bin",
+};
+
+static const struct of_device_id xway_gphy_match[] = {
+ { .compatible = "lantiq,xrx200-gphy-fw", .data = NULL },
+ { .compatible = "lantiq,xrx200a1x-gphy-fw", .data = &xrx200a1x_gphy_data },
+ { .compatible = "lantiq,xrx200a2x-gphy-fw", .data = &xrx200a2x_gphy_data },
+ { .compatible = "lantiq,xrx300-gphy-fw", .data = &xrx300_gphy_data },
+ { .compatible = "lantiq,xrx330-gphy-fw", .data = &xrx300_gphy_data },
+ {},
+};
+
+static int gswip_gphy_fw_load(struct gswip_priv *priv, struct gswip_gphy_fw *gphy_fw)
+{
+ struct device *dev = priv->dev;
+ const struct firmware *fw;
+ void *fw_addr;
+ dma_addr_t dma_addr;
+ dma_addr_t dev_addr;
+ size_t size;
+ int ret;
+
+ ret = clk_prepare_enable(gphy_fw->clk_gate);
+ if (ret)
+ return ret;
+
+ reset_control_assert(gphy_fw->reset);
+
+ ret = request_firmware(&fw, gphy_fw->fw_name, dev);
+ if (ret) {
+ dev_err(dev, "failed to load firmware: %s, error: %i\n",
+ gphy_fw->fw_name, ret);
+ return ret;
+ }
+
+ /* GPHY cores need the firmware code in a persistent and contiguous
+ * memory area with a 16 kB boundary aligned start address.
+ */
+ size = fw->size + XRX200_GPHY_FW_ALIGN;
+
+ fw_addr = dmam_alloc_coherent(dev, size, &dma_addr, GFP_KERNEL);
+ if (fw_addr) {
+ fw_addr = PTR_ALIGN(fw_addr, XRX200_GPHY_FW_ALIGN);
+ dev_addr = ALIGN(dma_addr, XRX200_GPHY_FW_ALIGN);
+ memcpy(fw_addr, fw->data, fw->size);
+ } else {
+ dev_err(dev, "failed to alloc firmware memory\n");
+ release_firmware(fw);
+ return -ENOMEM;
+ }
+
+ release_firmware(fw);
+
+ ret = regmap_write(priv->rcu_regmap, gphy_fw->fw_addr_offset, dev_addr);
+ if (ret)
+ return ret;
+
+ reset_control_deassert(gphy_fw->reset);
+
+ return ret;
+}
+
+static int gswip_gphy_fw_probe(struct gswip_priv *priv,
+ struct gswip_gphy_fw *gphy_fw,
+ struct device_node *gphy_fw_np, int i)
+{
+ struct device *dev = priv->dev;
+ u32 gphy_mode;
+ int ret;
+ char gphyname[10];
+
+ snprintf(gphyname, sizeof(gphyname), "gphy%d", i);
+
+ gphy_fw->clk_gate = devm_clk_get(dev, gphyname);
+ if (IS_ERR(gphy_fw->clk_gate)) {
+ dev_err(dev, "Failed to lookup gate clock\n");
+ return PTR_ERR(gphy_fw->clk_gate);
+ }
+
+ ret = of_property_read_u32(gphy_fw_np, "reg", &gphy_fw->fw_addr_offset);
+ if (ret)
+ return ret;
+
+ ret = of_property_read_u32(gphy_fw_np, "lantiq,gphy-mode", &gphy_mode);
+ /* Default to GE mode */
+ if (ret)
+ gphy_mode = GPHY_MODE_GE;
+
+ switch (gphy_mode) {
+ case GPHY_MODE_FE:
+ gphy_fw->fw_name = priv->gphy_fw_name_cfg->fe_firmware_name;
+ break;
+ case GPHY_MODE_GE:
+ gphy_fw->fw_name = priv->gphy_fw_name_cfg->ge_firmware_name;
+ break;
+ default:
+ dev_err(dev, "Unknown GPHY mode %d\n", gphy_mode);
+ return -EINVAL;
+ }
+
+ gphy_fw->reset = of_reset_control_array_get_exclusive(gphy_fw_np);
+ if (IS_ERR(priv->gphy_fw)) {
+ if (PTR_ERR(priv->gphy_fw) != -EPROBE_DEFER)
+ dev_err(dev, "Failed to lookup gphy reset\n");
+ return PTR_ERR(priv->gphy_fw);
+ }
+
+ return gswip_gphy_fw_load(priv, gphy_fw);
+}
+
+static void gswip_gphy_fw_remove(struct gswip_priv *priv,
+ struct gswip_gphy_fw *gphy_fw)
+{
+ int ret;
+
+ /* check if the device was fully probed */
+ if (!gphy_fw->fw_name)
+ return;
+
+ ret = regmap_write(priv->rcu_regmap, gphy_fw->fw_addr_offset, 0);
+ if (ret)
+ dev_err(priv->dev, "can not reset GPHY FW pointer");
+
+ clk_disable_unprepare(gphy_fw->clk_gate);
+
+ reset_control_put(gphy_fw->reset);
+}
+
+static int gswip_gphy_fw_list(struct gswip_priv *priv,
+ struct device_node *gphy_fw_list_np, u32 version)
+{
+ struct device *dev = priv->dev;
+ struct device_node *gphy_fw_np;
+ const struct of_device_id *match;
+ int err;
+ int i = 0;
+
+ /* The The VRX200 rev 1.1 uses the GSWIP 2.0 and needs the older
+ * GPHY firmware. The VRX200 rev 1.2 uses the GSWIP 2.1 and also
+ * needs a different GPHY firmware.
+ */
+ if (of_device_is_compatible(gphy_fw_list_np, "lantiq,xrx200-gphy-fw")) {
+ switch (version) {
+ case GSWIP_VERSION_2_0:
+ priv->gphy_fw_name_cfg = &xrx200a1x_gphy_data;
+ break;
+ case GSWIP_VERSION_2_1:
+ priv->gphy_fw_name_cfg = &xrx200a2x_gphy_data;
+ break;
+ default:
+ dev_err(dev, "unknown GSWIP version: 0x%x", version);
+ return -ENOENT;
+ }
+ }
+
+ match = of_match_node(xway_gphy_match, gphy_fw_list_np);
+ if (match && match->data)
+ priv->gphy_fw_name_cfg = match->data;
+
+ if (!priv->gphy_fw_name_cfg) {
+ dev_err(dev, "GPHY compatible type not supported");
+ return -ENOENT;
+ }
+
+ priv->num_gphy_fw = of_get_available_child_count(gphy_fw_list_np);
+ if (!priv->num_gphy_fw)
+ return -ENOENT;
+
+ priv->rcu_regmap = syscon_regmap_lookup_by_phandle(gphy_fw_list_np,
+ "lantiq,rcu");
+ if (IS_ERR(priv->rcu_regmap))
+ return PTR_ERR(priv->rcu_regmap);
+
+ priv->gphy_fw = devm_kmalloc_array(dev, priv->num_gphy_fw,
+ sizeof(*priv->gphy_fw),
+ GFP_KERNEL | __GFP_ZERO);
+ if (!priv->gphy_fw)
+ return -ENOMEM;
+
+ for_each_available_child_of_node(gphy_fw_list_np, gphy_fw_np) {
+ err = gswip_gphy_fw_probe(priv, &priv->gphy_fw[i],
+ gphy_fw_np, i);
+ if (err)
+ goto remove_gphy;
+ i++;
+ }
+
+ return 0;
+
+remove_gphy:
+ for (i = 0; i < priv->num_gphy_fw; i++)
+ gswip_gphy_fw_remove(priv, &priv->gphy_fw[i]);
+ return err;
+}
+
+static int gswip_probe(struct platform_device *pdev)
+{
+ struct gswip_priv *priv;
+ struct resource *gswip_res, *mdio_res, *mii_res;
+ struct device_node *mdio_np, *gphy_fw_np;
+ struct device *dev = &pdev->dev;
+ int err;
+ int i;
+ u32 version;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ gswip_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ priv->gswip = devm_ioremap_resource(dev, gswip_res);
+ if (!priv->gswip)
+ return -ENOMEM;
+
+ mdio_res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ priv->mdio = devm_ioremap_resource(dev, mdio_res);
+ if (!priv->mdio)
+ return -ENOMEM;
+
+ mii_res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
+ priv->mii = devm_ioremap_resource(dev, mii_res);
+ if (!priv->mii)
+ return -ENOMEM;
+
+ priv->hw_info = of_device_get_match_data(dev);
+ if (!priv->hw_info)
+ return -EINVAL;
+
+ priv->ds = dsa_switch_alloc(dev, priv->hw_info->max_ports);
+ if (!priv->ds)
+ return -ENOMEM;
+
+ priv->ds->priv = priv;
+ priv->ds->ops = &gswip_switch_ops;
+ priv->dev = dev;
+ version = gswip_switch_r(priv, GSWIP_VERSION);
+
+ /* bring up the mdio bus */
+ gphy_fw_np = of_find_compatible_node(pdev->dev.of_node, NULL,
+ "lantiq,gphy-fw");
+ if (gphy_fw_np) {
+ err = gswip_gphy_fw_list(priv, gphy_fw_np, version);
+ if (err) {
+ dev_err(dev, "gphy fw probe failed\n");
+ return err;
+ }
+ }
+
+ /* bring up the mdio bus */
+ mdio_np = of_find_compatible_node(pdev->dev.of_node, NULL,
+ "lantiq,xrx200-mdio");
+ if (mdio_np) {
+ err = gswip_mdio(priv, mdio_np);
+ if (err) {
+ dev_err(dev, "mdio probe failed\n");
+ goto gphy_fw;
+ }
+ }
+
+ err = dsa_register_switch(priv->ds);
+ if (err) {
+ dev_err(dev, "dsa switch register failed: %i\n", err);
+ goto mdio_bus;
+ }
+ if (priv->ds->dst->cpu_dp->index != priv->hw_info->cpu_port) {
+ dev_err(dev, "wrong CPU port defined, HW only supports port: %i",
+ priv->hw_info->cpu_port);
+ err = -EINVAL;
+ goto mdio_bus;
+ }
+
+ platform_set_drvdata(pdev, priv);
+
+ dev_info(dev, "probed GSWIP version %lx mod %lx\n",
+ (version & GSWIP_VERSION_REV_MASK) >> GSWIP_VERSION_REV_SHIFT,
+ (version & GSWIP_VERSION_MOD_MASK) >> GSWIP_VERSION_MOD_SHIFT);
+ return 0;
+
+mdio_bus:
+ if (mdio_np)
+ mdiobus_unregister(priv->ds->slave_mii_bus);
+gphy_fw:
+ for (i = 0; i < priv->num_gphy_fw; i++)
+ gswip_gphy_fw_remove(priv, &priv->gphy_fw[i]);
+ return err;
+}
+
+static int gswip_remove(struct platform_device *pdev)
+{
+ struct gswip_priv *priv = platform_get_drvdata(pdev);
+ int i;
+
+ if (!priv)
+ return 0;
+
+ /* disable the switch */
+ gswip_mdio_mask(priv, GSWIP_MDIO_GLOB_ENABLE, 0, GSWIP_MDIO_GLOB);
+
+ dsa_unregister_switch(priv->ds);
+
+ if (priv->ds->slave_mii_bus)
+ mdiobus_unregister(priv->ds->slave_mii_bus);
+
+ for (i = 0; i < priv->num_gphy_fw; i++)
+ gswip_gphy_fw_remove(priv, &priv->gphy_fw[i]);
+
+ return 0;
+}
+
+static const struct gswip_hw_info gswip_xrx200 = {
+ .max_ports = 7,
+ .cpu_port = 6,
+};
+
+static const struct of_device_id gswip_of_match[] = {
+ { .compatible = "lantiq,xrx200-gswip", .data = &gswip_xrx200 },
+ {},
+};
+MODULE_DEVICE_TABLE(of, gswip_of_match);
+
+static struct platform_driver gswip_driver = {
+ .probe = gswip_probe,
+ .remove = gswip_remove,
+ .driver = {
+ .name = "gswip",
+ .of_match_table = gswip_of_match,
+ },
+};
+
+module_platform_driver(gswip_driver);
+
+MODULE_AUTHOR("Hauke Mehrtens <hauke@hauke-m.de>");
+MODULE_DESCRIPTION("Lantiq / Intel GSWIP driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/net/dsa/lantiq_pce.h b/drivers/net/dsa/lantiq_pce.h
new file mode 100644
index 000000000000..180663138e75
--- /dev/null
+++ b/drivers/net/dsa/lantiq_pce.h
@@ -0,0 +1,153 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * PCE microcode extracted from UGW 7.1.1 switch api
+ *
+ * Copyright (c) 2012, 2014, 2015 Lantiq Deutschland GmbH
+ * Copyright (C) 2012 John Crispin <john@phrozen.org>
+ * Copyright (C) 2017 - 2018 Hauke Mehrtens <hauke@hauke-m.de>
+ */
+
+enum {
+ OUT_MAC0 = 0,
+ OUT_MAC1,
+ OUT_MAC2,
+ OUT_MAC3,
+ OUT_MAC4,
+ OUT_MAC5,
+ OUT_ETHTYP,
+ OUT_VTAG0,
+ OUT_VTAG1,
+ OUT_ITAG0,
+ OUT_ITAG1, /*10 */
+ OUT_ITAG2,
+ OUT_ITAG3,
+ OUT_IP0,
+ OUT_IP1,
+ OUT_IP2,
+ OUT_IP3,
+ OUT_SIP0,
+ OUT_SIP1,
+ OUT_SIP2,
+ OUT_SIP3, /*20*/
+ OUT_SIP4,
+ OUT_SIP5,
+ OUT_SIP6,
+ OUT_SIP7,
+ OUT_DIP0,
+ OUT_DIP1,
+ OUT_DIP2,
+ OUT_DIP3,
+ OUT_DIP4,
+ OUT_DIP5, /*30*/
+ OUT_DIP6,
+ OUT_DIP7,
+ OUT_SESID,
+ OUT_PROT,
+ OUT_APP0,
+ OUT_APP1,
+ OUT_IGMP0,
+ OUT_IGMP1,
+ OUT_IPOFF, /*39*/
+ OUT_NONE = 63,
+};
+
+/* parser's microcode length type */
+#define INSTR 0
+#define IPV6 1
+#define LENACCU 2
+
+/* parser's microcode flag type */
+enum {
+ FLAG_ITAG = 0,
+ FLAG_VLAN,
+ FLAG_SNAP,
+ FLAG_PPPOE,
+ FLAG_IPV6,
+ FLAG_IPV6FL,
+ FLAG_IPV4,
+ FLAG_IGMP,
+ FLAG_TU,
+ FLAG_HOP,
+ FLAG_NN1, /*10 */
+ FLAG_NN2,
+ FLAG_END,
+ FLAG_NO, /*13*/
+};
+
+struct gswip_pce_microcode {
+ u16 val_3;
+ u16 val_2;
+ u16 val_1;
+ u16 val_0;
+};
+
+#define MC_ENTRY(val, msk, ns, out, len, type, flags, ipv4_len) \
+ { val, msk, ((ns) << 10 | (out) << 4 | (len) >> 1),\
+ ((len) & 1) << 15 | (type) << 13 | (flags) << 9 | (ipv4_len) << 8 }
+static const struct gswip_pce_microcode gswip_pce_microcode[] = {
+ /* value mask ns fields L type flags ipv4_len */
+ MC_ENTRY(0x88c3, 0xFFFF, 1, OUT_ITAG0, 4, INSTR, FLAG_ITAG, 0),
+ MC_ENTRY(0x8100, 0xFFFF, 2, OUT_VTAG0, 2, INSTR, FLAG_VLAN, 0),
+ MC_ENTRY(0x88A8, 0xFFFF, 1, OUT_VTAG0, 2, INSTR, FLAG_VLAN, 0),
+ MC_ENTRY(0x8100, 0xFFFF, 1, OUT_VTAG0, 2, INSTR, FLAG_VLAN, 0),
+ MC_ENTRY(0x8864, 0xFFFF, 17, OUT_ETHTYP, 1, INSTR, FLAG_NO, 0),
+ MC_ENTRY(0x0800, 0xFFFF, 21, OUT_ETHTYP, 1, INSTR, FLAG_NO, 0),
+ MC_ENTRY(0x86DD, 0xFFFF, 22, OUT_ETHTYP, 1, INSTR, FLAG_NO, 0),
+ MC_ENTRY(0x8863, 0xFFFF, 16, OUT_ETHTYP, 1, INSTR, FLAG_NO, 0),
+ MC_ENTRY(0x0000, 0xF800, 10, OUT_NONE, 0, INSTR, FLAG_NO, 0),
+ MC_ENTRY(0x0000, 0x0000, 40, OUT_ETHTYP, 1, INSTR, FLAG_NO, 0),
+ MC_ENTRY(0x0600, 0x0600, 40, OUT_ETHTYP, 1, INSTR, FLAG_NO, 0),
+ MC_ENTRY(0x0000, 0x0000, 12, OUT_NONE, 1, INSTR, FLAG_NO, 0),
+ MC_ENTRY(0xAAAA, 0xFFFF, 14, OUT_NONE, 1, INSTR, FLAG_NO, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE, 0, INSTR, FLAG_NO, 0),
+ MC_ENTRY(0x0300, 0xFF00, 41, OUT_NONE, 0, INSTR, FLAG_SNAP, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE, 0, INSTR, FLAG_NO, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_DIP7, 3, INSTR, FLAG_NO, 0),
+ MC_ENTRY(0x0000, 0x0000, 18, OUT_DIP7, 3, INSTR, FLAG_PPPOE, 0),
+ MC_ENTRY(0x0021, 0xFFFF, 21, OUT_NONE, 1, INSTR, FLAG_NO, 0),
+ MC_ENTRY(0x0057, 0xFFFF, 22, OUT_NONE, 1, INSTR, FLAG_NO, 0),
+ MC_ENTRY(0x0000, 0x0000, 40, OUT_NONE, 0, INSTR, FLAG_NO, 0),
+ MC_ENTRY(0x4000, 0xF000, 24, OUT_IP0, 4, INSTR, FLAG_IPV4, 1),
+ MC_ENTRY(0x6000, 0xF000, 27, OUT_IP0, 3, INSTR, FLAG_IPV6, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE, 0, INSTR, FLAG_NO, 0),
+ MC_ENTRY(0x0000, 0x0000, 25, OUT_IP3, 2, INSTR, FLAG_NO, 0),
+ MC_ENTRY(0x0000, 0x0000, 26, OUT_SIP0, 4, INSTR, FLAG_NO, 0),
+ MC_ENTRY(0x0000, 0x0000, 40, OUT_NONE, 0, LENACCU, FLAG_NO, 0),
+ MC_ENTRY(0x1100, 0xFF00, 39, OUT_PROT, 1, INSTR, FLAG_NO, 0),
+ MC_ENTRY(0x0600, 0xFF00, 39, OUT_PROT, 1, INSTR, FLAG_NO, 0),
+ MC_ENTRY(0x0000, 0xFF00, 33, OUT_IP3, 17, INSTR, FLAG_HOP, 0),
+ MC_ENTRY(0x2B00, 0xFF00, 33, OUT_IP3, 17, INSTR, FLAG_NN1, 0),
+ MC_ENTRY(0x3C00, 0xFF00, 33, OUT_IP3, 17, INSTR, FLAG_NN2, 0),
+ MC_ENTRY(0x0000, 0x0000, 39, OUT_PROT, 1, INSTR, FLAG_NO, 0),
+ MC_ENTRY(0x0000, 0x00E0, 35, OUT_NONE, 0, INSTR, FLAG_NO, 0),
+ MC_ENTRY(0x0000, 0x0000, 40, OUT_NONE, 0, INSTR, FLAG_NO, 0),
+ MC_ENTRY(0x0000, 0xFF00, 33, OUT_NONE, 0, IPV6, FLAG_HOP, 0),
+ MC_ENTRY(0x2B00, 0xFF00, 33, OUT_NONE, 0, IPV6, FLAG_NN1, 0),
+ MC_ENTRY(0x3C00, 0xFF00, 33, OUT_NONE, 0, IPV6, FLAG_NN2, 0),
+ MC_ENTRY(0x0000, 0x0000, 40, OUT_PROT, 1, IPV6, FLAG_NO, 0),
+ MC_ENTRY(0x0000, 0x0000, 40, OUT_SIP0, 16, INSTR, FLAG_NO, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_APP0, 4, INSTR, FLAG_IGMP, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE, 0, INSTR, FLAG_END, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE, 0, INSTR, FLAG_END, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE, 0, INSTR, FLAG_END, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE, 0, INSTR, FLAG_END, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE, 0, INSTR, FLAG_END, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE, 0, INSTR, FLAG_END, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE, 0, INSTR, FLAG_END, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE, 0, INSTR, FLAG_END, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE, 0, INSTR, FLAG_END, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE, 0, INSTR, FLAG_END, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE, 0, INSTR, FLAG_END, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE, 0, INSTR, FLAG_END, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE, 0, INSTR, FLAG_END, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE, 0, INSTR, FLAG_END, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE, 0, INSTR, FLAG_END, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE, 0, INSTR, FLAG_END, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE, 0, INSTR, FLAG_END, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE, 0, INSTR, FLAG_END, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE, 0, INSTR, FLAG_END, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE, 0, INSTR, FLAG_END, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE, 0, INSTR, FLAG_END, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE, 0, INSTR, FLAG_END, 0),
+ MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE, 0, INSTR, FLAG_END, 0),
+};
--
2.11.0
^ permalink raw reply related [flat|nested] 7+ messages in thread