devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To: Lubomir Rintel <lkundrak@v3.sk>
Cc: Michael Turquette <mturquette@baylibre.com>,
	Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>,
	Stephen Boyd <sboyd@kernel.org>, James Cameron <quozl@laptop.org>,
	linux-input@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-clk@vger.kernel.org
Subject: Re: [PATCH v2 7/8] Input: olpc_apsp: enable the SP clock
Date: Wed, 10 Oct 2018 10:09:01 -0700	[thread overview]
Message-ID: <20181010170901.GC47260@dtor-ws> (raw)
In-Reply-To: <20181010142504.233467-8-lkundrak@v3.sk>

On Wed, Oct 10, 2018 at 04:25:03PM +0200, Lubomir Rintel wrote:
> Without the clock, the keyboard controller won't operate.
> Tested on an OLPC XO 1.75.
> 
> Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
> ---
>  drivers/input/serio/olpc_apsp.c | 13 +++++++++++++
>  1 file changed, 13 insertions(+)
> 
> diff --git a/drivers/input/serio/olpc_apsp.c b/drivers/input/serio/olpc_apsp.c
> index 8b19a47dfa46..fe9e19014e70 100644
> --- a/drivers/input/serio/olpc_apsp.c
> +++ b/drivers/input/serio/olpc_apsp.c
> @@ -23,6 +23,7 @@
>  #include <linux/of.h>
>  #include <linux/slab.h>
>  #include <linux/delay.h>
> +#include <linux/clk.h>
>  
>  /*
>   * The OLPC XO-1.75 and XO-4 laptops do not have a hardware PS/2 controller.
> @@ -74,6 +75,7 @@ struct olpc_apsp {
>  	struct serio *kbio;
>  	struct serio *padio;
>  	void __iomem *base;
> +	struct clk *clk;
>  	int open_count;
>  	int irq;
>  };
> @@ -146,8 +148,13 @@ static int olpc_apsp_open(struct serio *port)
>  	struct olpc_apsp *priv = port->port_data;
>  	unsigned int tmp;
>  	unsigned long l;
> +	int error;
>  
>  	if (priv->open_count++ == 0) {
> +		error = clk_prepare_enable(priv->clk);
> +		if (error)
> +			return error;
> +
>  		l = readl(priv->base + COMMAND_FIFO_STATUS);
>  		if (!(l & CMD_STS_MASK)) {
>  			dev_err(priv->dev, "SP cannot accept commands.\n");

I think you need to disable clock here.

> @@ -171,6 +178,8 @@ static void olpc_apsp_close(struct serio *port)
>  		/* Disable interrupt 0 */
>  		tmp = readl(priv->base + PJ_INTERRUPT_MASK);
>  		writel(tmp | INT_0, priv->base + PJ_INTERRUPT_MASK);
> +
> +		clk_disable_unprepare(priv->clk);
>  	}
>  }
>  
> @@ -198,6 +207,10 @@ static int olpc_apsp_probe(struct platform_device *pdev)
>  	if (priv->irq < 0)
>  		return priv->irq;
>  
> +	priv->clk = devm_clk_get(&pdev->dev, "sp");
> +	if (IS_ERR(priv->clk))
> +		return PTR_ERR(priv->clk);
> +
>  	/* KEYBOARD */
>  	kb_serio = kzalloc(sizeof(struct serio), GFP_KERNEL);
>  	if (!kb_serio)
> -- 
> 2.19.0
> 

-- 
Dmitry

  reply	other threads:[~2018-10-10 17:09 UTC|newest]

Thread overview: 32+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-10-10 14:24 [PATCH v2 0/8] OLPC 1.75 Keyboard/Touchpad fixes Lubomir Rintel
2018-10-10 14:24 ` [PATCH v2 1/8] dt-bindings: olpc,ap-sp: add clock Lubomir Rintel
2018-11-04 11:41   ` Pavel Machek
2018-10-10 14:24 ` [PATCH v2 2/8] dt-bindings: olpc,ap-sp: add GPIO lines Lubomir Rintel
2018-11-04 11:49   ` Pavel Machek
2018-10-10 14:24 ` [PATCH v2 3/8] dt-bindings: marvell,mmp2: Add clock id for the SP clock Lubomir Rintel
2018-11-04 11:48   ` Pavel Machek
2018-10-10 14:25 ` [PATCH v2 4/8] clk: mmp2: add " Lubomir Rintel
2018-11-04 11:48   ` Pavel Machek
2018-10-10 14:25 ` [PATCH v2 5/8] Input: olpc_apsp: depend on CONFIG_OF Lubomir Rintel
2018-10-10 17:18   ` Dmitry Torokhov
2018-11-04 11:50   ` Pavel Machek
2018-10-10 14:25 ` [PATCH v2 6/8] Input: olpc_apsp: check FIFO status on open(), not probe() Lubomir Rintel
2018-10-10 14:25 ` [PATCH v2 7/8] Input: olpc_apsp: enable the SP clock Lubomir Rintel
2018-10-10 17:09   ` Dmitry Torokhov [this message]
2018-11-04 11:53   ` Pavel Machek
2018-10-10 14:25 ` [PATCH v2 8/8] Input: olpc_apsp: allocate the GPIOs used Lubomir Rintel
2018-10-10 17:10   ` Dmitry Torokhov
2018-10-10 17:11     ` Dmitry Torokhov
2018-10-11  8:38   ` Linus Walleij
2018-11-04 11:55   ` Pavel Machek
2018-10-15 19:56 ` [PATCH v2 0/8] OLPC 1.75 Keyboard/Touchpad fixes Pavel Machek
2018-10-16  9:44   ` Lubomir Rintel
2018-10-30 10:01     ` Pavel Machek
2018-10-30 10:26       ` Pavel Machek
2018-10-30 19:40         ` Lubomir Rintel
2018-10-31  3:37           ` James Cameron
2018-10-31 12:46             ` Pavel Machek
2018-10-31 11:54           ` Pavel Machek
2018-11-01 13:47           ` Pavel Machek
2018-10-30 23:54         ` James Cameron
2018-10-31 12:29           ` Pavel Machek

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20181010170901.GC47260@dtor-ws \
    --to=dmitry.torokhov@gmail.com \
    --cc=devicetree@vger.kernel.org \
    --cc=linux-clk@vger.kernel.org \
    --cc=linux-input@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=lkundrak@v3.sk \
    --cc=mark.rutland@arm.com \
    --cc=mturquette@baylibre.com \
    --cc=quozl@laptop.org \
    --cc=robh+dt@kernel.org \
    --cc=sboyd@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).