* [PATCH v2 1/6] dt-bindings: drm/panel: simple: Add no-hpd property @ 2018-10-25 22:21 Douglas Anderson 2018-10-25 22:21 ` [PATCH v2 5/6] dt-bindings: drm/panel: simple: Innolux TV123WAM is actually P120ZDG-BF1 Douglas Anderson 2018-10-29 16:16 ` [PATCH v2 1/6] dt-bindings: drm/panel: simple: Add no-hpd property Sean Paul 0 siblings, 2 replies; 7+ messages in thread From: Douglas Anderson @ 2018-10-25 22:21 UTC (permalink / raw) To: Sean Paul, Thierry Reding, Sandeep Panda Cc: linux-arm-msm, Laurent Pinchart, jsanka, ryandcase, Douglas Anderson, devicetree, linux-kernel, dri-devel, Rob Herring, David Airlie, Mark Rutland Some eDP panels that are designed to be always connected to a board use their HPD signal to signal that they've finished powering on and they're ready to be talked to. However, for various reasons it's possible that the HPD signal from the panel isn't actually hooked up. In the case where the HPD isn't hooked up you can look at the timing diagram on the panel datasheet and insert a delay for the maximum amount of time that the HPD might take to come up. Let's add a property in the device tree for this concept. Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Sean Paul <sean@poorly.run> Reviewed-by: Rob Herring <robh@kernel.org> --- Changes in v2: None .../devicetree/bindings/display/panel/simple-panel.txt | 3 +++ 1 file changed, 3 insertions(+) diff --git a/Documentation/devicetree/bindings/display/panel/simple-panel.txt b/Documentation/devicetree/bindings/display/panel/simple-panel.txt index 45a457ad38f0..b2b872c710f2 100644 --- a/Documentation/devicetree/bindings/display/panel/simple-panel.txt +++ b/Documentation/devicetree/bindings/display/panel/simple-panel.txt @@ -11,6 +11,9 @@ Optional properties: - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing - enable-gpios: GPIO pin to enable or disable the panel - backlight: phandle of the backlight device attached to the panel +- no-hpd: This panel is supposed to communicate that it's ready via HPD + (hot plug detect) signal, but the signal isn't hooked up so we should + hardcode the max delay from the panel spec when powering up the panel. Example: -- 2.19.1.568.g152ad8e336-goog ^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH v2 5/6] dt-bindings: drm/panel: simple: Innolux TV123WAM is actually P120ZDG-BF1 2018-10-25 22:21 [PATCH v2 1/6] dt-bindings: drm/panel: simple: Add no-hpd property Douglas Anderson @ 2018-10-25 22:21 ` Douglas Anderson 2018-10-26 14:43 ` Sean Paul 2018-10-29 9:10 ` Andrzej Hajda 2018-10-29 16:16 ` [PATCH v2 1/6] dt-bindings: drm/panel: simple: Add no-hpd property Sean Paul 1 sibling, 2 replies; 7+ messages in thread From: Douglas Anderson @ 2018-10-25 22:21 UTC (permalink / raw) To: Sean Paul, Thierry Reding, Sandeep Panda Cc: linux-arm-msm, Laurent Pinchart, jsanka, ryandcase, Douglas Anderson, devicetree, linux-kernel, dri-devel, Rob Herring, David Airlie, Mark Rutland As far as I can tell the bindings that were added in commit 9c04400f7ea6 ("dt-bindings: drm/panel: Document Innolux TV123WAM panel bindings") weren't actually for Innolux TV123WAM but were actually for Innolux P120ZDG-BF1. As far as I can tell the Innolux TV123WAM isn't a real panel and but it's a mosh between the TI TV123WAM and the Innolux P120ZDG-BF1. Let's unmosh. Here's my evidence: * Searching for TV123WAM on the Internet turns up a TI panel. While it's possible that an Innolux panel has the same model number as the TI Panel, it seems a little doubtful. Looking up the datasheet from the TI Panel shows that it's 1920 x 1280 and 259.2 mm x 172.8 mm. * As far as I know, the patch adding the Innolux Panel was supposed to be for the board that's sitting in front of me as I type this (support for that board is not yet upstream). On the back of that panel I see Innolux P120ZDZ-EZ1 rev B1. * Someone pointed me at a datasheet that's supposed to be for the panel in front of me (sorry, I can't share the datasheet). That datasheet has the string "p120zdg-bf1" * If I search for "P120ZDG-BF1" on the Internet I get hits for panels that are 2160x1440. They don't have datasheets, but the fact that the resolution matches is a good sign. While we doing the rename, also mention that no-hpd can be used with this panel. See the previous patch in this series ("drm/panel: simple: Add "no-hpd" delay for Innolux TV123WAM"). Fixes: 9c04400f7ea6 ("dt-bindings: drm/panel: Document Innolux TV123WAM panel bindings") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Rob Herring <robh@kernel.org> Cc: Sandeep Panda <spanda@codeaurora.org> --- Changes in v2: None .../{innolux,tv123wam.txt => innolux,p120zdg-bf1.txt} | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-) rename Documentation/devicetree/bindings/display/panel/{innolux,tv123wam.txt => innolux,p120zdg-bf1.txt} (70%) diff --git a/Documentation/devicetree/bindings/display/panel/innolux,tv123wam.txt b/Documentation/devicetree/bindings/display/panel/innolux,p120zdg-bf1.txt similarity index 70% rename from Documentation/devicetree/bindings/display/panel/innolux,tv123wam.txt rename to Documentation/devicetree/bindings/display/panel/innolux,p120zdg-bf1.txt index a9b35265fa13..513f03466aba 100644 --- a/Documentation/devicetree/bindings/display/panel/innolux,tv123wam.txt +++ b/Documentation/devicetree/bindings/display/panel/innolux,p120zdg-bf1.txt @@ -1,20 +1,22 @@ -Innolux TV123WAM 12.3 inch eDP 2K display panel +Innolux P120ZDG-BF1 12.02 inch eDP 2K display panel This binding is compatible with the simple-panel binding, which is specified in simple-panel.txt in this directory. Required properties: -- compatible: should be "innolux,tv123wam" +- compatible: should be "innolux,p120zdg-bf1" - power-supply: regulator to provide the supply voltage Optional properties: - enable-gpios: GPIO pin to enable or disable the panel - backlight: phandle of the backlight device attached to the panel +- no-hpd: If HPD isn't hooked up; add this property. Example: panel_edp: panel-edp { - compatible = "innolux,tv123wam"; + compatible = "innolux,p120zdg-bf1"; enable-gpios = <&msmgpio 31 GPIO_ACTIVE_LOW>; power-supply = <&pm8916_l2>; backlight = <&backlight>; + no-hpd; }; -- 2.19.1.568.g152ad8e336-goog ^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH v2 5/6] dt-bindings: drm/panel: simple: Innolux TV123WAM is actually P120ZDG-BF1 2018-10-25 22:21 ` [PATCH v2 5/6] dt-bindings: drm/panel: simple: Innolux TV123WAM is actually P120ZDG-BF1 Douglas Anderson @ 2018-10-26 14:43 ` Sean Paul 2018-10-26 14:46 ` Sean Paul 2018-10-29 9:10 ` Andrzej Hajda 1 sibling, 1 reply; 7+ messages in thread From: Sean Paul @ 2018-10-26 14:43 UTC (permalink / raw) To: Douglas Anderson Cc: Sean Paul, Thierry Reding, Sandeep Panda, linux-arm-msm, Laurent Pinchart, jsanka, ryandcase, devicetree, linux-kernel, dri-devel, Rob Herring, David Airlie, Mark Rutland On Thu, Oct 25, 2018 at 03:21:33PM -0700, Douglas Anderson wrote: > As far as I can tell the bindings that were added in commit > 9c04400f7ea6 ("dt-bindings: drm/panel: Document Innolux TV123WAM panel > bindings") weren't actually for Innolux TV123WAM but were actually for > Innolux P120ZDG-BF1. > > As far as I can tell the Innolux TV123WAM isn't a real panel and but > it's a mosh between the TI TV123WAM and the Innolux P120ZDG-BF1. > Let's unmosh. > > Here's my evidence: > > * Searching for TV123WAM on the Internet turns up a TI panel. While > it's possible that an Innolux panel has the same model number as the > TI Panel, it seems a little doubtful. Looking up the datasheet from > the TI Panel shows that it's 1920 x 1280 and 259.2 mm x 172.8 mm. > > * As far as I know, the patch adding the Innolux Panel was supposed to > be for the board that's sitting in front of me as I type this > (support for that board is not yet upstream). On the back of that > panel I see Innolux P120ZDZ-EZ1 rev B1. > > * Someone pointed me at a datasheet that's supposed to be for the > panel in front of me (sorry, I can't share the datasheet). That > datasheet has the string "p120zdg-bf1" > > * If I search for "P120ZDG-BF1" on the Internet I get hits for panels > that are 2160x1440. They don't have datasheets, but the fact that > the resolution matches is a good sign. > > While we doing the rename, also mention that no-hpd can be used with > this panel. See the previous patch in this series ("drm/panel: > simple: Add "no-hpd" delay for Innolux TV123WAM"). > > Fixes: 9c04400f7ea6 ("dt-bindings: drm/panel: Document Innolux TV123WAM panel bindings") > Signed-off-by: Douglas Anderson <dianders@chromium.org> > Reviewed-by: Rob Herring <robh@kernel.org> I didn't see your v2 when I replied to the v1 patch, so for the record, Reviewed-by: Sean Paul <sean@poorly.run> Also note to whoever applies this to -misc, v1 also had Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> Sean > Cc: Sandeep Panda <spanda@codeaurora.org> > --- > > Changes in v2: None > > .../{innolux,tv123wam.txt => innolux,p120zdg-bf1.txt} | 8 +++++--- > 1 file changed, 5 insertions(+), 3 deletions(-) > rename Documentation/devicetree/bindings/display/panel/{innolux,tv123wam.txt => innolux,p120zdg-bf1.txt} (70%) > > diff --git a/Documentation/devicetree/bindings/display/panel/innolux,tv123wam.txt b/Documentation/devicetree/bindings/display/panel/innolux,p120zdg-bf1.txt > similarity index 70% > rename from Documentation/devicetree/bindings/display/panel/innolux,tv123wam.txt > rename to Documentation/devicetree/bindings/display/panel/innolux,p120zdg-bf1.txt > index a9b35265fa13..513f03466aba 100644 > --- a/Documentation/devicetree/bindings/display/panel/innolux,tv123wam.txt > +++ b/Documentation/devicetree/bindings/display/panel/innolux,p120zdg-bf1.txt > @@ -1,20 +1,22 @@ > -Innolux TV123WAM 12.3 inch eDP 2K display panel > +Innolux P120ZDG-BF1 12.02 inch eDP 2K display panel > > This binding is compatible with the simple-panel binding, which is specified > in simple-panel.txt in this directory. > > Required properties: > -- compatible: should be "innolux,tv123wam" > +- compatible: should be "innolux,p120zdg-bf1" > - power-supply: regulator to provide the supply voltage > > Optional properties: > - enable-gpios: GPIO pin to enable or disable the panel > - backlight: phandle of the backlight device attached to the panel > +- no-hpd: If HPD isn't hooked up; add this property. > > Example: > panel_edp: panel-edp { > - compatible = "innolux,tv123wam"; > + compatible = "innolux,p120zdg-bf1"; > enable-gpios = <&msmgpio 31 GPIO_ACTIVE_LOW>; > power-supply = <&pm8916_l2>; > backlight = <&backlight>; > + no-hpd; > }; > -- > 2.19.1.568.g152ad8e336-goog > -- Sean Paul, Software Engineer, Google / Chromium OS ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v2 5/6] dt-bindings: drm/panel: simple: Innolux TV123WAM is actually P120ZDG-BF1 2018-10-26 14:43 ` Sean Paul @ 2018-10-26 14:46 ` Sean Paul 2018-10-26 15:01 ` Doug Anderson 0 siblings, 1 reply; 7+ messages in thread From: Sean Paul @ 2018-10-26 14:46 UTC (permalink / raw) To: Douglas Anderson Cc: Mark Rutland, devicetree, David Airlie, linux-arm-msm, Sandeep Panda, dri-devel, linux-kernel, Rob Herring, Thierry Reding, Sean Paul, Laurent Pinchart, ryandcase On Fri, Oct 26, 2018 at 10:43:56AM -0400, Sean Paul wrote: > On Thu, Oct 25, 2018 at 03:21:33PM -0700, Douglas Anderson wrote: > > As far as I can tell the bindings that were added in commit > > 9c04400f7ea6 ("dt-bindings: drm/panel: Document Innolux TV123WAM panel > > bindings") weren't actually for Innolux TV123WAM but were actually for > > Innolux P120ZDG-BF1. > > > > As far as I can tell the Innolux TV123WAM isn't a real panel and but > > it's a mosh between the TI TV123WAM and the Innolux P120ZDG-BF1. > > Let's unmosh. > > > > Here's my evidence: > > > > * Searching for TV123WAM on the Internet turns up a TI panel. While > > it's possible that an Innolux panel has the same model number as the > > TI Panel, it seems a little doubtful. Looking up the datasheet from > > the TI Panel shows that it's 1920 x 1280 and 259.2 mm x 172.8 mm. > > > > * As far as I know, the patch adding the Innolux Panel was supposed to > > be for the board that's sitting in front of me as I type this > > (support for that board is not yet upstream). On the back of that > > panel I see Innolux P120ZDZ-EZ1 rev B1. > > > > * Someone pointed me at a datasheet that's supposed to be for the > > panel in front of me (sorry, I can't share the datasheet). That > > datasheet has the string "p120zdg-bf1" > > > > * If I search for "P120ZDG-BF1" on the Internet I get hits for panels > > that are 2160x1440. They don't have datasheets, but the fact that > > the resolution matches is a good sign. > > > > While we doing the rename, also mention that no-hpd can be used with > > this panel. See the previous patch in this series ("drm/panel: > > simple: Add "no-hpd" delay for Innolux TV123WAM"). > > > > Fixes: 9c04400f7ea6 ("dt-bindings: drm/panel: Document Innolux TV123WAM panel bindings") > > Signed-off-by: Douglas Anderson <dianders@chromium.org> > > Reviewed-by: Rob Herring <robh@kernel.org> > > I didn't see your v2 when I replied to the v1 patch, so for the record, > > Reviewed-by: Sean Paul <sean@poorly.run> > > Also note to whoever applies this to -misc, v1 also had > > Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> And I just realized that patches 5 & 6 were swapped in v2. So nevermind this, Doug's v2 tags are correct. Dear coffee, please kick in soon. Sean > > > Sean > > > Cc: Sandeep Panda <spanda@codeaurora.org> > > --- > > > > Changes in v2: None > > > > .../{innolux,tv123wam.txt => innolux,p120zdg-bf1.txt} | 8 +++++--- > > 1 file changed, 5 insertions(+), 3 deletions(-) > > rename Documentation/devicetree/bindings/display/panel/{innolux,tv123wam.txt => innolux,p120zdg-bf1.txt} (70%) > > > > diff --git a/Documentation/devicetree/bindings/display/panel/innolux,tv123wam.txt b/Documentation/devicetree/bindings/display/panel/innolux,p120zdg-bf1.txt > > similarity index 70% > > rename from Documentation/devicetree/bindings/display/panel/innolux,tv123wam.txt > > rename to Documentation/devicetree/bindings/display/panel/innolux,p120zdg-bf1.txt > > index a9b35265fa13..513f03466aba 100644 > > --- a/Documentation/devicetree/bindings/display/panel/innolux,tv123wam.txt > > +++ b/Documentation/devicetree/bindings/display/panel/innolux,p120zdg-bf1.txt > > @@ -1,20 +1,22 @@ > > -Innolux TV123WAM 12.3 inch eDP 2K display panel > > +Innolux P120ZDG-BF1 12.02 inch eDP 2K display panel > > > > This binding is compatible with the simple-panel binding, which is specified > > in simple-panel.txt in this directory. > > > > Required properties: > > -- compatible: should be "innolux,tv123wam" > > +- compatible: should be "innolux,p120zdg-bf1" > > - power-supply: regulator to provide the supply voltage > > > > Optional properties: > > - enable-gpios: GPIO pin to enable or disable the panel > > - backlight: phandle of the backlight device attached to the panel > > +- no-hpd: If HPD isn't hooked up; add this property. > > > > Example: > > panel_edp: panel-edp { > > - compatible = "innolux,tv123wam"; > > + compatible = "innolux,p120zdg-bf1"; > > enable-gpios = <&msmgpio 31 GPIO_ACTIVE_LOW>; > > power-supply = <&pm8916_l2>; > > backlight = <&backlight>; > > + no-hpd; > > }; > > -- > > 2.19.1.568.g152ad8e336-goog > > > > -- > Sean Paul, Software Engineer, Google / Chromium OS -- Sean Paul, Software Engineer, Google / Chromium OS _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v2 5/6] dt-bindings: drm/panel: simple: Innolux TV123WAM is actually P120ZDG-BF1 2018-10-26 14:46 ` Sean Paul @ 2018-10-26 15:01 ` Doug Anderson 0 siblings, 0 replies; 7+ messages in thread From: Doug Anderson @ 2018-10-26 15:01 UTC (permalink / raw) To: sean Cc: Sean Paul, Thierry Reding, Sandeep Panda, linux-arm-msm, Laurent Pinchart, Jeykumar Sankaran, ryandcase, devicetree, LKML, dri-devel, Rob Herring, David Airlie, Mark Rutland Sean, On Fri, Oct 26, 2018 at 7:47 AM Sean Paul <sean@poorly.run> wrote: > > I didn't see your v2 when I replied to the v1 patch, so for the record, > > > > Reviewed-by: Sean Paul <sean@poorly.run> > > > > Also note to whoever applies this to -misc, v1 also had > > > > Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> > > And I just realized that patches 5 & 6 were swapped in v2. So nevermind this, > Doug's v2 tags are correct. > > Dear coffee, please kick in soon. Sorry about that--I should have mentioned it in the notes. I realized that the bindings were supposed to land before the code so I swapped them. Thanks for your review! -Doug ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v2 5/6] dt-bindings: drm/panel: simple: Innolux TV123WAM is actually P120ZDG-BF1 2018-10-25 22:21 ` [PATCH v2 5/6] dt-bindings: drm/panel: simple: Innolux TV123WAM is actually P120ZDG-BF1 Douglas Anderson 2018-10-26 14:43 ` Sean Paul @ 2018-10-29 9:10 ` Andrzej Hajda 1 sibling, 0 replies; 7+ messages in thread From: Andrzej Hajda @ 2018-10-29 9:10 UTC (permalink / raw) To: Douglas Anderson, Sean Paul, Thierry Reding, Sandeep Panda Cc: Mark Rutland, devicetree, David Airlie, linux-arm-msm, dri-devel, linux-kernel, Rob Herring, ryandcase, Laurent Pinchart On 26.10.2018 00:21, Douglas Anderson wrote: > As far as I can tell the bindings that were added in commit > 9c04400f7ea6 ("dt-bindings: drm/panel: Document Innolux TV123WAM panel > bindings") weren't actually for Innolux TV123WAM but were actually for > Innolux P120ZDG-BF1. > > As far as I can tell the Innolux TV123WAM isn't a real panel and but > it's a mosh between the TI TV123WAM and the Innolux P120ZDG-BF1. > Let's unmosh. > > Here's my evidence: > > * Searching for TV123WAM on the Internet turns up a TI panel. While > it's possible that an Innolux panel has the same model number as the > TI Panel, it seems a little doubtful. Looking up the datasheet from > the TI Panel shows that it's 1920 x 1280 and 259.2 mm x 172.8 mm. > > * As far as I know, the patch adding the Innolux Panel was supposed to > be for the board that's sitting in front of me as I type this > (support for that board is not yet upstream). On the back of that > panel I see Innolux P120ZDZ-EZ1 rev B1. > > * Someone pointed me at a datasheet that's supposed to be for the > panel in front of me (sorry, I can't share the datasheet). That > datasheet has the string "p120zdg-bf1" > > * If I search for "P120ZDG-BF1" on the Internet I get hits for panels > that are 2160x1440. They don't have datasheets, but the fact that > the resolution matches is a good sign. > > While we doing the rename, also mention that no-hpd can be used with > this panel. See the previous patch in this series ("drm/panel: > simple: Add "no-hpd" delay for Innolux TV123WAM"). > > Fixes: 9c04400f7ea6 ("dt-bindings: drm/panel: Document Innolux TV123WAM panel bindings") > Signed-off-by: Douglas Anderson <dianders@chromium.org> > Reviewed-by: Rob Herring <robh@kernel.org> > Cc: Sandeep Panda <spanda@codeaurora.org> Grats for good deduction. Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> -- Regards Andrzej ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v2 1/6] dt-bindings: drm/panel: simple: Add no-hpd property 2018-10-25 22:21 [PATCH v2 1/6] dt-bindings: drm/panel: simple: Add no-hpd property Douglas Anderson 2018-10-25 22:21 ` [PATCH v2 5/6] dt-bindings: drm/panel: simple: Innolux TV123WAM is actually P120ZDG-BF1 Douglas Anderson @ 2018-10-29 16:16 ` Sean Paul 1 sibling, 0 replies; 7+ messages in thread From: Sean Paul @ 2018-10-29 16:16 UTC (permalink / raw) To: Douglas Anderson Cc: Sean Paul, Thierry Reding, Sandeep Panda, linux-arm-msm, Laurent Pinchart, jsanka, ryandcase, devicetree, linux-kernel, dri-devel, Rob Herring, David Airlie, Mark Rutland On Thu, Oct 25, 2018 at 03:21:29PM -0700, Douglas Anderson wrote: > Some eDP panels that are designed to be always connected to a board > use their HPD signal to signal that they've finished powering on and > they're ready to be talked to. > > However, for various reasons it's possible that the HPD signal from > the panel isn't actually hooked up. In the case where the HPD isn't > hooked up you can look at the timing diagram on the panel datasheet > and insert a delay for the maximum amount of time that the HPD might > take to come up. > > Let's add a property in the device tree for this concept. > > Signed-off-by: Douglas Anderson <dianders@chromium.org> Thanks for the series, Doug, I've applied it all to drm-misc-next-fixes for 4.20. Sean > Reviewed-by: Sean Paul <sean@poorly.run> > Reviewed-by: Rob Herring <robh@kernel.org> > --- > > Changes in v2: None > > .../devicetree/bindings/display/panel/simple-panel.txt | 3 +++ > 1 file changed, 3 insertions(+) > > diff --git a/Documentation/devicetree/bindings/display/panel/simple-panel.txt b/Documentation/devicetree/bindings/display/panel/simple-panel.txt > index 45a457ad38f0..b2b872c710f2 100644 > --- a/Documentation/devicetree/bindings/display/panel/simple-panel.txt > +++ b/Documentation/devicetree/bindings/display/panel/simple-panel.txt > @@ -11,6 +11,9 @@ Optional properties: > - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing > - enable-gpios: GPIO pin to enable or disable the panel > - backlight: phandle of the backlight device attached to the panel > +- no-hpd: This panel is supposed to communicate that it's ready via HPD > + (hot plug detect) signal, but the signal isn't hooked up so we should > + hardcode the max delay from the panel spec when powering up the panel. > > Example: > > -- > 2.19.1.568.g152ad8e336-goog > -- Sean Paul, Software Engineer, Google / Chromium OS ^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2018-10-29 16:16 UTC | newest] Thread overview: 7+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2018-10-25 22:21 [PATCH v2 1/6] dt-bindings: drm/panel: simple: Add no-hpd property Douglas Anderson 2018-10-25 22:21 ` [PATCH v2 5/6] dt-bindings: drm/panel: simple: Innolux TV123WAM is actually P120ZDG-BF1 Douglas Anderson 2018-10-26 14:43 ` Sean Paul 2018-10-26 14:46 ` Sean Paul 2018-10-26 15:01 ` Doug Anderson 2018-10-29 9:10 ` Andrzej Hajda 2018-10-29 16:16 ` [PATCH v2 1/6] dt-bindings: drm/panel: simple: Add no-hpd property Sean Paul
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).