* [PATCH] ARM: dts: imx: Add dummy PHYs for HSIC-only USB controllers
@ 2018-10-18 7:45 Frieder Schrempf
2018-10-25 13:08 ` Fabio Estevam
` (2 more replies)
0 siblings, 3 replies; 6+ messages in thread
From: Frieder Schrempf @ 2018-10-18 7:45 UTC (permalink / raw)
To: devicetree, peter.chen
Cc: Frieder Schrempf, Shawn Guo, Sascha Hauer,
Pengutronix Kernel Team, Fabio Estevam, NXP Linux Team,
Rob Herring, Mark Rutland, linux-arm-kernel, linux-kernel
Some SOCs in the i.MX6 family have a USB host controller that is
only capable of the HSIC interface and has no on-board PHY.
To be able to use these controllers, we need to add "usb-nop-xceiv"
dummy PHYs.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
arch/arm/boot/dts/imx6qdl.dtsi | 14 ++++++++++++++
arch/arm/boot/dts/imx6sl.dtsi | 7 +++++++
arch/arm/boot/dts/imx6sx.dtsi | 6 ++++++
3 files changed, 27 insertions(+)
diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi
index 61d2d26..d3404d1 100644
--- a/arch/arm/boot/dts/imx6qdl.dtsi
+++ b/arch/arm/boot/dts/imx6qdl.dtsi
@@ -139,6 +139,16 @@
interrupts = <0 94 IRQ_TYPE_LEVEL_HIGH>;
};
+ usbphynop1: usbphynop1 {
+ compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
+ };
+
+ usbphynop2: usbphynop2 {
+ compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
+ };
+
soc {
#address-cells = <1>;
#size-cells = <1>;
@@ -981,6 +991,8 @@
reg = <0x02184400 0x200>;
interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6QDL_CLK_USBOH3>;
+ fsl,usbphy = <&usbphynop1>;
+ phy_type = "hsic";
fsl,usbmisc = <&usbmisc 2>;
dr_mode = "host";
ahb-burst-config = <0x0>;
@@ -994,6 +1006,8 @@
reg = <0x02184600 0x200>;
interrupts = <0 42 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6QDL_CLK_USBOH3>;
+ fsl,usbphy = <&usbphynop2>;
+ phy_type = "hsic";
fsl,usbmisc = <&usbmisc 3>;
dr_mode = "host";
ahb-burst-config = <0x0>;
diff --git a/arch/arm/boot/dts/imx6sl.dtsi b/arch/arm/boot/dts/imx6sl.dtsi
index 7a4f5da..81edcdc 100644
--- a/arch/arm/boot/dts/imx6sl.dtsi
+++ b/arch/arm/boot/dts/imx6sl.dtsi
@@ -110,6 +110,11 @@
interrupts = <0 94 IRQ_TYPE_LEVEL_HIGH>;
};
+ usbphynop1: usbphynop1 {
+ compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
+ };
+
soc {
#address-cells = <1>;
#size-cells = <1>;
@@ -815,6 +820,8 @@
reg = <0x02184400 0x200>;
interrupts = <0 40 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6SL_CLK_USBOH3>;
+ fsl,usbphy = <&usbphynop1>;
+ phy_type = "hsic";
fsl,usbmisc = <&usbmisc 2>;
dr_mode = "host";
ahb-burst-config = <0x0>;
diff --git a/arch/arm/boot/dts/imx6sx.dtsi b/arch/arm/boot/dts/imx6sx.dtsi
index 844caa3..07ed417 100644
--- a/arch/arm/boot/dts/imx6sx.dtsi
+++ b/arch/arm/boot/dts/imx6sx.dtsi
@@ -159,6 +159,11 @@
interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
};
+ usbphynop1: usbphynop1 {
+ compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
+ };
+
soc {
#address-cells = <1>;
#size-cells = <1>;
@@ -877,6 +882,7 @@
reg = <0x02184400 0x200>;
interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6SX_CLK_USBOH3>;
+ fsl,usbphy = <&usbphynop1>;
fsl,usbmisc = <&usbmisc 2>;
phy_type = "hsic";
fsl,anatop = <&anatop>;
--
2.7.4
^ permalink raw reply related [flat|nested] 6+ messages in thread* Re: [PATCH] ARM: dts: imx: Add dummy PHYs for HSIC-only USB controllers
2018-10-18 7:45 [PATCH] ARM: dts: imx: Add dummy PHYs for HSIC-only USB controllers Frieder Schrempf
@ 2018-10-25 13:08 ` Fabio Estevam
2018-10-31 7:31 ` Shawn Guo
2018-11-26 14:02 ` Shawn Guo
2 siblings, 0 replies; 6+ messages in thread
From: Fabio Estevam @ 2018-10-25 13:08 UTC (permalink / raw)
To: frieder.schrempf
Cc: open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Peter Chen, Shawn Guo, Sascha Hauer, Sascha Hauer, Fabio Estevam,
NXP Linux Team, Rob Herring, Mark Rutland,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE,
linux-kernel
On Thu, Oct 18, 2018 at 5:00 AM Frieder Schrempf
<frieder.schrempf@kontron.de> wrote:
>
> Some SOCs in the i.MX6 family have a USB host controller that is
> only capable of the HSIC interface and has no on-board PHY.
>
> To be able to use these controllers, we need to add "usb-nop-xceiv"
> dummy PHYs.
>
> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] ARM: dts: imx: Add dummy PHYs for HSIC-only USB controllers
2018-10-18 7:45 [PATCH] ARM: dts: imx: Add dummy PHYs for HSIC-only USB controllers Frieder Schrempf
2018-10-25 13:08 ` Fabio Estevam
@ 2018-10-31 7:31 ` Shawn Guo
2018-11-22 6:48 ` PETER CHEN
2018-11-26 14:02 ` Shawn Guo
2 siblings, 1 reply; 6+ messages in thread
From: Shawn Guo @ 2018-10-31 7:31 UTC (permalink / raw)
To: Frieder Schrempf, peter.chen
Cc: devicetree, Mark Rutland, Sascha Hauer, linux-kernel, Rob Herring,
NXP Linux Team, Pengutronix Kernel Team, Fabio Estevam,
linux-arm-kernel
On Thu, Oct 18, 2018 at 09:45:04AM +0200, Frieder Schrempf wrote:
> Some SOCs in the i.MX6 family have a USB host controller that is
> only capable of the HSIC interface and has no on-board PHY.
>
> To be able to use these controllers, we need to add "usb-nop-xceiv"
> dummy PHYs.
>
> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
@Peter, looks good to you?
Shawn
> ---
> arch/arm/boot/dts/imx6qdl.dtsi | 14 ++++++++++++++
> arch/arm/boot/dts/imx6sl.dtsi | 7 +++++++
> arch/arm/boot/dts/imx6sx.dtsi | 6 ++++++
> 3 files changed, 27 insertions(+)
>
> diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi
> index 61d2d26..d3404d1 100644
> --- a/arch/arm/boot/dts/imx6qdl.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl.dtsi
> @@ -139,6 +139,16 @@
> interrupts = <0 94 IRQ_TYPE_LEVEL_HIGH>;
> };
>
> + usbphynop1: usbphynop1 {
> + compatible = "usb-nop-xceiv";
> + #phy-cells = <0>;
> + };
> +
> + usbphynop2: usbphynop2 {
> + compatible = "usb-nop-xceiv";
> + #phy-cells = <0>;
> + };
> +
> soc {
> #address-cells = <1>;
> #size-cells = <1>;
> @@ -981,6 +991,8 @@
> reg = <0x02184400 0x200>;
> interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&clks IMX6QDL_CLK_USBOH3>;
> + fsl,usbphy = <&usbphynop1>;
> + phy_type = "hsic";
> fsl,usbmisc = <&usbmisc 2>;
> dr_mode = "host";
> ahb-burst-config = <0x0>;
> @@ -994,6 +1006,8 @@
> reg = <0x02184600 0x200>;
> interrupts = <0 42 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&clks IMX6QDL_CLK_USBOH3>;
> + fsl,usbphy = <&usbphynop2>;
> + phy_type = "hsic";
> fsl,usbmisc = <&usbmisc 3>;
> dr_mode = "host";
> ahb-burst-config = <0x0>;
> diff --git a/arch/arm/boot/dts/imx6sl.dtsi b/arch/arm/boot/dts/imx6sl.dtsi
> index 7a4f5da..81edcdc 100644
> --- a/arch/arm/boot/dts/imx6sl.dtsi
> +++ b/arch/arm/boot/dts/imx6sl.dtsi
> @@ -110,6 +110,11 @@
> interrupts = <0 94 IRQ_TYPE_LEVEL_HIGH>;
> };
>
> + usbphynop1: usbphynop1 {
> + compatible = "usb-nop-xceiv";
> + #phy-cells = <0>;
> + };
> +
> soc {
> #address-cells = <1>;
> #size-cells = <1>;
> @@ -815,6 +820,8 @@
> reg = <0x02184400 0x200>;
> interrupts = <0 40 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&clks IMX6SL_CLK_USBOH3>;
> + fsl,usbphy = <&usbphynop1>;
> + phy_type = "hsic";
> fsl,usbmisc = <&usbmisc 2>;
> dr_mode = "host";
> ahb-burst-config = <0x0>;
> diff --git a/arch/arm/boot/dts/imx6sx.dtsi b/arch/arm/boot/dts/imx6sx.dtsi
> index 844caa3..07ed417 100644
> --- a/arch/arm/boot/dts/imx6sx.dtsi
> +++ b/arch/arm/boot/dts/imx6sx.dtsi
> @@ -159,6 +159,11 @@
> interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
> };
>
> + usbphynop1: usbphynop1 {
> + compatible = "usb-nop-xceiv";
> + #phy-cells = <0>;
> + };
> +
> soc {
> #address-cells = <1>;
> #size-cells = <1>;
> @@ -877,6 +882,7 @@
> reg = <0x02184400 0x200>;
> interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&clks IMX6SX_CLK_USBOH3>;
> + fsl,usbphy = <&usbphynop1>;
> fsl,usbmisc = <&usbmisc 2>;
> phy_type = "hsic";
> fsl,anatop = <&anatop>;
> --
> 2.7.4
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 6+ messages in thread* RE: [PATCH] ARM: dts: imx: Add dummy PHYs for HSIC-only USB controllers
2018-10-31 7:31 ` Shawn Guo
@ 2018-11-22 6:48 ` PETER CHEN
2018-11-22 7:41 ` Schrempf Frieder
0 siblings, 1 reply; 6+ messages in thread
From: PETER CHEN @ 2018-11-22 6:48 UTC (permalink / raw)
To: Shawn Guo, Frieder Schrempf
Cc: devicetree@vger.kernel.org, Mark Rutland, Sascha Hauer,
linux-kernel@vger.kernel.org, Rob Herring, dl-linux-imx,
Pengutronix Kernel Team, Fabio Estevam,
linux-arm-kernel@lists.infradead.org
>
> On Thu, Oct 18, 2018 at 09:45:04AM +0200, Frieder Schrempf wrote:
> > Some SOCs in the i.MX6 family have a USB host controller that is only
> > capable of the HSIC interface and has no on-board PHY.
> >
> > To be able to use these controllers, we need to add "usb-nop-xceiv"
> > dummy PHYs.
> >
> > Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
>
> @Peter, looks good to you?
>
> Shawn
>
> > ---
> > arch/arm/boot/dts/imx6qdl.dtsi | 14 ++++++++++++++
> > arch/arm/boot/dts/imx6sl.dtsi | 7 +++++++
> > arch/arm/boot/dts/imx6sx.dtsi | 6 ++++++
> > 3 files changed, 27 insertions(+)
> >
> > diff --git a/arch/arm/boot/dts/imx6qdl.dtsi
> > b/arch/arm/boot/dts/imx6qdl.dtsi index 61d2d26..d3404d1 100644
> > --- a/arch/arm/boot/dts/imx6qdl.dtsi
> > +++ b/arch/arm/boot/dts/imx6qdl.dtsi
> > @@ -139,6 +139,16 @@
> > interrupts = <0 94 IRQ_TYPE_LEVEL_HIGH>;
> > };
> >
> > + usbphynop1: usbphynop1 {
> > + compatible = "usb-nop-xceiv";
> > + #phy-cells = <0>;
> > + };
> > +
Why #phy-cells property is needed? Others are ok for me.
Peter
> > + usbphynop2: usbphynop2 {
> > + compatible = "usb-nop-xceiv";
> > + #phy-cells = <0>;
> > + };
> > +
> > soc {
> > #address-cells = <1>;
> > #size-cells = <1>;
> > @@ -981,6 +991,8 @@
> > reg = <0x02184400 0x200>;
> > interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>;
> > clocks = <&clks IMX6QDL_CLK_USBOH3>;
> > + fsl,usbphy = <&usbphynop1>;
> > + phy_type = "hsic";
> > fsl,usbmisc = <&usbmisc 2>;
> > dr_mode = "host";
> > ahb-burst-config = <0x0>;
> > @@ -994,6 +1006,8 @@
> > reg = <0x02184600 0x200>;
> > interrupts = <0 42 IRQ_TYPE_LEVEL_HIGH>;
> > clocks = <&clks IMX6QDL_CLK_USBOH3>;
> > + fsl,usbphy = <&usbphynop2>;
> > + phy_type = "hsic";
> > fsl,usbmisc = <&usbmisc 3>;
> > dr_mode = "host";
> > ahb-burst-config = <0x0>;
> > diff --git a/arch/arm/boot/dts/imx6sl.dtsi
> > b/arch/arm/boot/dts/imx6sl.dtsi index 7a4f5da..81edcdc 100644
> > --- a/arch/arm/boot/dts/imx6sl.dtsi
> > +++ b/arch/arm/boot/dts/imx6sl.dtsi
> > @@ -110,6 +110,11 @@
> > interrupts = <0 94 IRQ_TYPE_LEVEL_HIGH>;
> > };
> >
> > + usbphynop1: usbphynop1 {
> > + compatible = "usb-nop-xceiv";
> > + #phy-cells = <0>;
> > + };
> > +
> > soc {
> > #address-cells = <1>;
> > #size-cells = <1>;
> > @@ -815,6 +820,8 @@
> > reg = <0x02184400 0x200>;
> > interrupts = <0 40 IRQ_TYPE_LEVEL_HIGH>;
> > clocks = <&clks IMX6SL_CLK_USBOH3>;
> > + fsl,usbphy = <&usbphynop1>;
> > + phy_type = "hsic";
> > fsl,usbmisc = <&usbmisc 2>;
> > dr_mode = "host";
> > ahb-burst-config = <0x0>;
> > diff --git a/arch/arm/boot/dts/imx6sx.dtsi
> > b/arch/arm/boot/dts/imx6sx.dtsi index 844caa3..07ed417 100644
> > --- a/arch/arm/boot/dts/imx6sx.dtsi
> > +++ b/arch/arm/boot/dts/imx6sx.dtsi
> > @@ -159,6 +159,11 @@
> > interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
> > };
> >
> > + usbphynop1: usbphynop1 {
> > + compatible = "usb-nop-xceiv";
> > + #phy-cells = <0>;
> > + };
> > +
> > soc {
> > #address-cells = <1>;
> > #size-cells = <1>;
> > @@ -877,6 +882,7 @@
> > reg = <0x02184400 0x200>;
> > interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
> > clocks = <&clks IMX6SX_CLK_USBOH3>;
> > + fsl,usbphy = <&usbphynop1>;
> > fsl,usbmisc = <&usbmisc 2>;
> > phy_type = "hsic";
> > fsl,anatop = <&anatop>;
> > --
> > 2.7.4
> >
^ permalink raw reply [flat|nested] 6+ messages in thread* Re: [PATCH] ARM: dts: imx: Add dummy PHYs for HSIC-only USB controllers
2018-11-22 6:48 ` PETER CHEN
@ 2018-11-22 7:41 ` Schrempf Frieder
0 siblings, 0 replies; 6+ messages in thread
From: Schrempf Frieder @ 2018-11-22 7:41 UTC (permalink / raw)
To: PETER CHEN, Shawn Guo
Cc: devicetree@vger.kernel.org, Mark Rutland, Sascha Hauer,
linux-kernel@vger.kernel.org, Rob Herring, dl-linux-imx,
Pengutronix Kernel Team, Fabio Estevam,
linux-arm-kernel@lists.infradead.org
On 22.11.18 07:48, PETER CHEN wrote:
>
>>
>> On Thu, Oct 18, 2018 at 09:45:04AM +0200, Frieder Schrempf wrote:
>>> Some SOCs in the i.MX6 family have a USB host controller that is only
>>> capable of the HSIC interface and has no on-board PHY.
>>>
>>> To be able to use these controllers, we need to add "usb-nop-xceiv"
>>> dummy PHYs.
>>>
>>> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
>>
>> @Peter, looks good to you?
>>
>> Shawn
>>
>>> ---
>>> arch/arm/boot/dts/imx6qdl.dtsi | 14 ++++++++++++++
>>> arch/arm/boot/dts/imx6sl.dtsi | 7 +++++++
>>> arch/arm/boot/dts/imx6sx.dtsi | 6 ++++++
>>> 3 files changed, 27 insertions(+)
>>>
>>> diff --git a/arch/arm/boot/dts/imx6qdl.dtsi
>>> b/arch/arm/boot/dts/imx6qdl.dtsi index 61d2d26..d3404d1 100644
>>> --- a/arch/arm/boot/dts/imx6qdl.dtsi
>>> +++ b/arch/arm/boot/dts/imx6qdl.dtsi
>>> @@ -139,6 +139,16 @@
>>> interrupts = <0 94 IRQ_TYPE_LEVEL_HIGH>;
>>> };
>>>
>>> + usbphynop1: usbphynop1 {
>>> + compatible = "usb-nop-xceiv";
>>> + #phy-cells = <0>;
>>> + };
>>> +
>
> Why #phy-cells property is needed? Others are ok for me.
From Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt:
Required properties:
- compatible: should be usb-nop-xceiv
- #phy-cells: Must be 0
>
> Peter
>
>>> + usbphynop2: usbphynop2 {
>>> + compatible = "usb-nop-xceiv";
>>> + #phy-cells = <0>;
>>> + };
>>> +
>>> soc {
>>> #address-cells = <1>;
>>> #size-cells = <1>;
>>> @@ -981,6 +991,8 @@
>>> reg = <0x02184400 0x200>;
>>> interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>;
>>> clocks = <&clks IMX6QDL_CLK_USBOH3>;
>>> + fsl,usbphy = <&usbphynop1>;
>>> + phy_type = "hsic";
>>> fsl,usbmisc = <&usbmisc 2>;
>>> dr_mode = "host";
>>> ahb-burst-config = <0x0>;
>>> @@ -994,6 +1006,8 @@
>>> reg = <0x02184600 0x200>;
>>> interrupts = <0 42 IRQ_TYPE_LEVEL_HIGH>;
>>> clocks = <&clks IMX6QDL_CLK_USBOH3>;
>>> + fsl,usbphy = <&usbphynop2>;
>>> + phy_type = "hsic";
>>> fsl,usbmisc = <&usbmisc 3>;
>>> dr_mode = "host";
>>> ahb-burst-config = <0x0>;
>>> diff --git a/arch/arm/boot/dts/imx6sl.dtsi
>>> b/arch/arm/boot/dts/imx6sl.dtsi index 7a4f5da..81edcdc 100644
>>> --- a/arch/arm/boot/dts/imx6sl.dtsi
>>> +++ b/arch/arm/boot/dts/imx6sl.dtsi
>>> @@ -110,6 +110,11 @@
>>> interrupts = <0 94 IRQ_TYPE_LEVEL_HIGH>;
>>> };
>>>
>>> + usbphynop1: usbphynop1 {
>>> + compatible = "usb-nop-xceiv";
>>> + #phy-cells = <0>;
>>> + };
>>> +
>>> soc {
>>> #address-cells = <1>;
>>> #size-cells = <1>;
>>> @@ -815,6 +820,8 @@
>>> reg = <0x02184400 0x200>;
>>> interrupts = <0 40 IRQ_TYPE_LEVEL_HIGH>;
>>> clocks = <&clks IMX6SL_CLK_USBOH3>;
>>> + fsl,usbphy = <&usbphynop1>;
>>> + phy_type = "hsic";
>>> fsl,usbmisc = <&usbmisc 2>;
>>> dr_mode = "host";
>>> ahb-burst-config = <0x0>;
>>> diff --git a/arch/arm/boot/dts/imx6sx.dtsi
>>> b/arch/arm/boot/dts/imx6sx.dtsi index 844caa3..07ed417 100644
>>> --- a/arch/arm/boot/dts/imx6sx.dtsi
>>> +++ b/arch/arm/boot/dts/imx6sx.dtsi
>>> @@ -159,6 +159,11 @@
>>> interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
>>> };
>>>
>>> + usbphynop1: usbphynop1 {
>>> + compatible = "usb-nop-xceiv";
>>> + #phy-cells = <0>;
>>> + };
>>> +
>>> soc {
>>> #address-cells = <1>;
>>> #size-cells = <1>;
>>> @@ -877,6 +882,7 @@
>>> reg = <0x02184400 0x200>;
>>> interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
>>> clocks = <&clks IMX6SX_CLK_USBOH3>;
>>> + fsl,usbphy = <&usbphynop1>;
>>> fsl,usbmisc = <&usbmisc 2>;
>>> phy_type = "hsic";
>>> fsl,anatop = <&anatop>;
>>> --
>>> 2.7.4
>>>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] ARM: dts: imx: Add dummy PHYs for HSIC-only USB controllers
2018-10-18 7:45 [PATCH] ARM: dts: imx: Add dummy PHYs for HSIC-only USB controllers Frieder Schrempf
2018-10-25 13:08 ` Fabio Estevam
2018-10-31 7:31 ` Shawn Guo
@ 2018-11-26 14:02 ` Shawn Guo
2 siblings, 0 replies; 6+ messages in thread
From: Shawn Guo @ 2018-11-26 14:02 UTC (permalink / raw)
To: Frieder Schrempf
Cc: devicetree, peter.chen, Mark Rutland, Sascha Hauer, linux-kernel,
Rob Herring, NXP Linux Team, Pengutronix Kernel Team,
Fabio Estevam, linux-arm-kernel
On Thu, Oct 18, 2018 at 09:45:04AM +0200, Frieder Schrempf wrote:
> Some SOCs in the i.MX6 family have a USB host controller that is
> only capable of the HSIC interface and has no on-board PHY.
>
> To be able to use these controllers, we need to add "usb-nop-xceiv"
> dummy PHYs.
>
> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Applied, thanks.
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2018-11-26 14:02 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2018-10-18 7:45 [PATCH] ARM: dts: imx: Add dummy PHYs for HSIC-only USB controllers Frieder Schrempf
2018-10-25 13:08 ` Fabio Estevam
2018-10-31 7:31 ` Shawn Guo
2018-11-22 6:48 ` PETER CHEN
2018-11-22 7:41 ` Schrempf Frieder
2018-11-26 14:02 ` Shawn Guo
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).