devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Rob Herring <robh@kernel.org>
To: Biao Huang <biao.huang@mediatek.com>
Cc: mark.rutland@arm.com, devicetree@vger.kernel.org,
	nelson.chang@mediatek.com, andrew@lunn.ch,
	netdev@vger.kernel.org, sean.wang@mediatek.com,
	liguo.zhang@mediatek.com, linux-kernel@vger.kernel.org,
	matthias.bgg@gmail.com, joabreu@synopsys.com,
	linux-mediatek@lists.infradead.org, honghui.zhang@mediatek.com,
	yt.shen@mediatek.com, davem@davemloft.net,
	linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH 2/2] dt-binding: mediatek-dwmac: add binding document for MediaTek MT2712 DWMAC
Date: Mon, 12 Nov 2018 10:22:07 -0600	[thread overview]
Message-ID: <20181112162204.GA8910@bogus> (raw)
In-Reply-To: <1540782294-27721-3-git-send-email-biao.huang@mediatek.com>

On Mon, Oct 29, 2018 at 11:04:54AM +0800, Biao Huang wrote:
> The commit adds the device tree binding documentation for the MediaTek DWMAC
> found on MediaTek MT2712.
> 
> Signed-off-by: Biao Huang <biao.huang@mediatek.com>
> ---
>  .../devicetree/bindings/net/mediatek-dwmac.txt     |   49 ++++++++++++++++++++
>  1 file changed, 49 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/mediatek-dwmac.txt
> 
> diff --git a/Documentation/devicetree/bindings/net/mediatek-dwmac.txt b/Documentation/devicetree/bindings/net/mediatek-dwmac.txt
> new file mode 100644
> index 0000000..8baf0e4
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/mediatek-dwmac.txt
> @@ -0,0 +1,49 @@
> +MediaTek DWMAC glue layer controller
> +
> +This file documents platform glue layer for stmmac.
> +Please see stmmac.txt for the other unchanged properties.
> +
> +The device node has following properties.
> +
> +Required properties:
> +- compatible:  Should be "mediatek,mt2712-gmac" for MT2712 SoC
> +- reg:  Address and length of the register set for the device
> +- interrupts:  Should contain the MAC interrupts
> +- interrupt-names: Should contain a list of interrupt names corresponding to
> +	the interrupts in the interrupts property, if available.
> +	Should be "macirq" for the main MAC IRQ
> +- clocks: Must contain a phandle for each entry in clock-names.
> +- clock-names: the name of the clock listed in the clocks property. These are
> +	"axi", "apb", "mac_ext", "mac_parent", "ptp_ref", "ptp_parent", "ptp_top"
> +	for MT2712 SoC

Clocks should represent the physical clocks connected to a block. Parent 
clocks are not in that category.

> +- mac-address: See ethernet.txt in the same directory
> +- phy-mode: See ethernet.txt in the same directory
> +
> +Example:
> +
> +	eth: ethernet@1101c000 {
> +		compatible = "mediatek,mt2712-gmac";
> +		reg = <0 0x1101c000 0 0x1300>;
> +		interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>;
> +		interrupt-names = "macirq";
> +		phy-mode ="rgmii-id";
> +		mac-address = [00 55 7b b5 7d f7];
> +		clock-names = "axi",
> +			      "apb",
> +			      "mac_ext",
> +			      "mac_parent",
> +			      "ptp_ref",
> +			      "ptp_parent",
> +			      "ptp_top";
> +		clocks = <&pericfg CLK_PERI_GMAC>,
> +			 <&pericfg CLK_PERI_GMAC_PCLK>,
> +			 <&topckgen CLK_TOP_ETHER_125M_SEL>,
> +			 <&topckgen CLK_TOP_ETHERPLL_125M>,
> +			 <&topckgen CLK_TOP_ETHER_50M_SEL>,
> +			 <&topckgen CLK_TOP_APLL1_D3>,
> +			 <&topckgen CLK_TOP_APLL1>;
> +		snps,txpbl = <32>;
> +		snps,rxpbl = <32>;
> +		snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>;
> +		snps,reset-active-low;
> +	};
> -- 
> 1.7.9.5
> 

  reply	other threads:[~2018-11-12 16:22 UTC|newest]

Thread overview: 11+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-10-29  3:04 [v2, PATCH 0/2] add Ethernet driver support for mt2712 Biao Huang
2018-10-29  3:04 ` [PATCH 1/2] net:stmmac: dwmac-mediatek: add " Biao Huang
2018-10-29 10:08   ` Corentin Labbe
2018-10-30  7:16     ` biao huang
2018-10-30 11:56       ` Andrew Lunn
2018-10-29 12:27   ` Andrew Lunn
2018-10-30  7:11     ` biao huang
2018-10-29  3:04 ` [PATCH 2/2] dt-binding: mediatek-dwmac: add binding document for MediaTek MT2712 DWMAC Biao Huang
2018-11-12 16:22   ` Rob Herring [this message]
2018-11-16  6:58     ` biao huang
2018-10-29  3:32 ` [v2, PATCH 0/2] add Ethernet driver support for mt2712 biao huang

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20181112162204.GA8910@bogus \
    --to=robh@kernel.org \
    --cc=andrew@lunn.ch \
    --cc=biao.huang@mediatek.com \
    --cc=davem@davemloft.net \
    --cc=devicetree@vger.kernel.org \
    --cc=honghui.zhang@mediatek.com \
    --cc=joabreu@synopsys.com \
    --cc=liguo.zhang@mediatek.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mediatek@lists.infradead.org \
    --cc=mark.rutland@arm.com \
    --cc=matthias.bgg@gmail.com \
    --cc=nelson.chang@mediatek.com \
    --cc=netdev@vger.kernel.org \
    --cc=sean.wang@mediatek.com \
    --cc=yt.shen@mediatek.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).