From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: Andy Gross <andy.gross@linaro.org>, David Brown <david.brown@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
linux-arm-msm@vger.kernel.org, linux-soc@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH 2/3] arm64: dts: qcom: qcs404: Define remaining UARTs
Date: Sun, 18 Nov 2018 12:01:34 -0800 [thread overview]
Message-ID: <20181118200135.25258-3-bjorn.andersson@linaro.org> (raw)
In-Reply-To: <20181118200135.25258-1-bjorn.andersson@linaro.org>
Add the BLSP2 BAM and add the remaining four UARTs found on the QCS404
platform.
Note that these has not been tested.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
arch/arm64/boot/dts/qcom/qcs404.dtsi | 84 ++++++++++++++++++++++++++++
1 file changed, 84 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi
index 9ec5c85fcb81..ca00987d6400 100644
--- a/arch/arm64/boot/dts/qcom/qcs404.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi
@@ -273,6 +273,16 @@
interrupt-controller;
#interrupt-cells = <2>;
+ blsp1_uart0_default: blsp1-uart0-default {
+ pins = "gpio30", "gpio31", "gpio32", "gpio33";
+ function = "blsp_uart0";
+ };
+
+ blsp1_uart1_default: blsp1-uart1-default {
+ pins = "gpio22", "gpio23";
+ function = "blsp_uart1";
+ };
+
blsp1_uart2_default: blsp1-uart2-default {
rx {
pins = "gpio18";
@@ -284,6 +294,16 @@
function = "blsp_uart_tx_a2";
};
};
+
+ blsp1_uart3_default: blsp1-uart3-default {
+ pins = "gpio82", "gpio83", "gpio84", "gpio85";
+ function = "blsp_uart3";
+ };
+
+ blsp2_uart0_default: blsp2-uart0-default {
+ pins = "gpio26", "gpio27", "gpio28", "gpio29";
+ function = "blsp_uart5";
+ };
};
gcc: clock-controller@1800000 {
@@ -347,6 +367,32 @@
status = "okay";
};
+ blsp1_uart0: serial@78af000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x078af000 0x200>;
+ interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_UART0_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp1_dma 1>, <&blsp1_dma 0>;
+ dma-names = "rx", "tx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_uart0_default>;
+ status = "disabled";
+ };
+
+ blsp1_uart1: serial@78b0000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x078b0000 0x200>;
+ interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp1_dma 3>, <&blsp1_dma 2>;
+ dma-names = "rx", "tx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_uart1_default>;
+ status = "disabled";
+ };
+
blsp1_uart2: serial@78b1000 {
compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
reg = <0x078b1000 0x200>;
@@ -360,6 +406,44 @@
status = "okay";
};
+ blsp1_uart3: serial@78b2000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x078b2000 0x200>;
+ interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp1_dma 7>, <&blsp1_dma 6>;
+ dma-names = "rx", "tx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_uart3_default>;
+ status = "disabled";
+ };
+
+ blsp2_dma: dma@7ac4000 {
+ compatible = "qcom,bam-v1.7.0";
+ reg = <0x07ac4000 0x17000>;
+ interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP2_AHB_CLK>;
+ clock-names = "bam_clk";
+ #dma-cells = <1>;
+ qcom,controlled-remotely = <1>;
+ qcom,ee = <0>;
+ status = "disabled";
+ };
+
+ blsp2_uart0: serial@7aef000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x07aef000 0x200>;
+ interrupts = <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP2_UART0_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp2_dma 1>, <&blsp2_dma 0>;
+ dma-names = "rx", "tx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp2_uart0_default>;
+ status = "disabled";
+ };
+
intc: interrupt-controller@b000000 {
compatible = "qcom,msm-qgic2";
interrupt-controller;
--
2.18.0
next prev parent reply other threads:[~2018-11-18 20:01 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-11-18 20:01 [PATCH 0/3] arm64: dts: qcom: QCS404 BLSP nodes Bjorn Andersson
2018-11-18 20:01 ` [PATCH 1/3] arm64: dts: qcom: qcs404: Specify pinctrl state for UART Bjorn Andersson
2018-11-18 20:01 ` Bjorn Andersson [this message]
2018-11-18 20:01 ` [PATCH 3/3] arm64: dts: qcom: qcs404: Add QUP I2C and SPI nodes Bjorn Andersson
2018-11-29 14:34 ` [PATCH 0/3] arm64: dts: qcom: QCS404 BLSP nodes Vinod Koul
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181118200135.25258-3-bjorn.andersson@linaro.org \
--to=bjorn.andersson@linaro.org \
--cc=andy.gross@linaro.org \
--cc=david.brown@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-soc@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox