[PATCH v3 00/15] Add initial RDA8810PL SoC and Orange Pi boards support

[PATCH v3 00/15] Add initial RDA8810PL SoC and Orange Pi boards support

[Manivannan Sadhasivam]

Hello,

This patchset adds initial RDA8810PL SoC and Orange Pi boards (2G IoT and
i96) support. RDA8810PL is an ARM Cortex A5 based SoC with Vivante's GC860
GPU. The SoC has been added as a new ARM sub architecture with myself
and Andreas as the maintainers.

More information about the boards can be found in below links:

1. Orange Pi 2G-IoT - http://www.orangepi.org/OrangePi2GIOT/
2. Orange Pi i96 - https://www.96boards.org/product/orangepi-i96/

This patchset is based on the initial revision sent out by Andreas long
back (http://lists.infradead.org/pipermail/linux-arm-kernel/2017-June/515951.html).

I have extended his patchset with proper irqchip and UART drivers. Now,
boards can boot into initramfs with console at UART2.

Thanks,
Mani

Changes in v3:

As per Marc's review:

* Removed unused header and defines from irqchip driver.
* Removed setting flow handlers from set_type callback.
* Minor code cleanups.

As per Arnd's review:

* Modified the UART indexes to start from 1 to match the SoC numbering
* Enabled exposed UARTs (all 3 on both boards)
* Modified the serial aliases as per board numbering

* Added Greg's Reviewed-by tag for serial driver.

Changes in v2:

* Used readl/writel_relaxed calls for both irqchip and timer drivers as
  per Marc's review.
* Implemented the logic to prevent counter wrapping during read as
  suggested by Marc.
* Used the timer-of API as per Daniel's suggestion.
* Added description about the timer in both commit log and driver.
* Changed the Vendor name for RDA to Unisoc Communications Inc.
* Removed the soc node level and cleaned up devicetrees as per Rob's
  review.
* Merged interrupt controller DT patch to SoC.
* Moved aliases to board dts as per Arnd's suggestion.
* Removed RDA Micro support mail address and used Unisoc one and added
  my missing signed off by tag as per Andreas's comments.

Andreas Färber (4):
  dt-bindings: Add RDA Micro vendor prefix
  dt-bindings: arm: Document RDA8810PL and reference boards
  ARM: Prepare RDA8810PL SoC
  dt-bindings: serial: Document RDA Micro UART

Manivannan Sadhasivam (11):
  dt-bindings: interrupt-controller: Document RDA8810PL intc
  arm: dts: Add devicetree for RDA8810PL SoC
  arm: dts: Add devicetree for OrangePi 2G IoT board
  arm: dts: Add devicetree for OrangePi i96 board
  irqchip: Add RDA8810PL interrupt driver
  dt-bindings: timer: Document RDA8810PL SoC timer
  arm: dts: rda8810pl: Add timer support
  clocksource: Add clock driver for RDA8810PL SoC
  arm: dts: rda8810pl: Add interrupt support for UART
  tty: serial: Add RDA8810PL UART driver
  MAINTAINERS: Add entry for RDA Micro SoC architecture

 .../admin-guide/kernel-parameters.txt         |   6 +
 Documentation/devicetree/bindings/arm/rda.txt |  17 +
 .../interrupt-controller/rda,8810pl-intc.txt  |  61 ++
 .../bindings/serial/rda,8810pl-uart.txt       |  15 +
 .../bindings/timer/rda,8810pl-timer.txt       |  21 +
 .../devicetree/bindings/vendor-prefixes.txt   |   1 +
 MAINTAINERS                                   |  14 +
 arch/arm/Kconfig                              |   2 +
 arch/arm/Makefile                             |   1 +
 arch/arm/boot/dts/Makefile                    |   3 +
 .../boot/dts/rda8810pl-orangepi-2g-iot.dts    |  50 ++
 arch/arm/boot/dts/rda8810pl-orangepi-i96.dts  |  50 ++
 arch/arm/boot/dts/rda8810pl.dtsi              |  99 +++
 arch/arm/mach-rda/Kconfig                     |   9 +
 arch/arm/mach-rda/Makefile                    |   1 +
 drivers/clocksource/Kconfig                   |   8 +
 drivers/clocksource/Makefile                  |   1 +
 drivers/clocksource/timer-rda.c               | 195 ++++
 drivers/irqchip/Kconfig                       |   4 +
 drivers/irqchip/Makefile                      |   1 +
 drivers/irqchip/irq-rda-intc.c                | 107 +++
 drivers/tty/serial/Kconfig                    |  19 +
 drivers/tty/serial/Makefile                   |   1 +
 drivers/tty/serial/rda-uart.c                 | 831 ++++++++++++++++++
 include/uapi/linux/serial_core.h              |   3 +
 25 files changed, 1520 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/arm/rda.txt
 create mode 100644 Documentation/devicetree/bindings/interrupt-controller/rda,8810pl-intc.txt
 create mode 100644 Documentation/devicetree/bindings/serial/rda,8810pl-uart.txt
 create mode 100644 Documentation/devicetree/bindings/timer/rda,8810pl-timer.txt
 create mode 100644 arch/arm/boot/dts/rda8810pl-orangepi-2g-iot.dts
 create mode 100644 arch/arm/boot/dts/rda8810pl-orangepi-i96.dts
 create mode 100644 arch/arm/boot/dts/rda8810pl.dtsi
 create mode 100644 arch/arm/mach-rda/Kconfig
 create mode 100644 arch/arm/mach-rda/Makefile
 create mode 100644 drivers/clocksource/timer-rda.c
 create mode 100644 drivers/irqchip/irq-rda-intc.c
 create mode 100644 drivers/tty/serial/rda-uart.c

-- 
2.17.1

[PATCH v3 01/15] dt-bindings: Add RDA Micro vendor prefix

[Manivannan Sadhasivam]

From: Andreas Färber <afaerber@suse.de>

Add vendor prefix for RDA Micro which now merged into Unisoc
Communications Inc.

Cc: overseas.sales@unisoc.com
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 4b1a2a8fcc16..37826fac7684 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -320,6 +320,7 @@ ralink	Mediatek/Ralink Technology Corp.
 ramtron	Ramtron International
 raspberrypi	Raspberry Pi Foundation
 raydium	Raydium Semiconductor Corp.
+rda	Unisoc Communications, Inc.
 realtek Realtek Semiconductor Corp.
 renesas	Renesas Electronics Corporation
 richtek	Richtek Technology Corporation
-- 
2.17.1

Re: [PATCH v3 01/15] dt-bindings: Add RDA Micro vendor prefix

[Rob Herring]

On Wed, 28 Nov 2018 19:20:52 +0530, Manivannan Sadhasivam wrote:
> From: Andreas Färber <afaerber@suse.de>
> 
> Add vendor prefix for RDA Micro which now merged into Unisoc
> Communications Inc.
> 
> Cc: overseas.sales@unisoc.com
> Signed-off-by: Andreas Färber <afaerber@suse.de>
> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> ---
>  Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
>  1 file changed, 1 insertion(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

[PATCH v3 02/15] dt-bindings: arm: Document RDA8810PL and reference boards

[Manivannan Sadhasivam]

From: Andreas Färber <afaerber@suse.de>

Add bindings for RDA Micro RDA8810PL SoC and below reference boards:

1. Orange Pi 2G-IoT - http://www.orangepi.org/OrangePi2GIOT/
2. Orange Pi i96 - https://www.96boards.org/product/orangepi-i96/

Cc: overseas.sales@unisoc.com
Cc: zhao_steven@263.net
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 Documentation/devicetree/bindings/arm/rda.txt | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/arm/rda.txt

diff --git a/Documentation/devicetree/bindings/arm/rda.txt b/Documentation/devicetree/bindings/arm/rda.txt
new file mode 100644
index 000000000000..43c80762c428
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/rda.txt
@@ -0,0 +1,17 @@
+RDA Micro platforms device tree bindings
+----------------------------------------
+
+RDA8810PL SoC
+=============
+
+Required root node properties:
+
+ - compatible :  must contain "rda,8810pl"
+
+
+Boards:
+
+Root node property compatible must contain, depending on board:
+
+ - Orange Pi 2G-IoT: "xunlong,orangepi-2g-iot"
+ - Orange Pi i96: "xunlong,orangepi-i96"
-- 
2.17.1

Re: [PATCH v3 02/15] dt-bindings: arm: Document RDA8810PL and reference boards

[Rob Herring]

On Wed, 28 Nov 2018 19:20:53 +0530, Manivannan Sadhasivam wrote:
> From: Andreas Färber <afaerber@suse.de>
> 
> Add bindings for RDA Micro RDA8810PL SoC and below reference boards:
> 
> 1. Orange Pi 2G-IoT - http://www.orangepi.org/OrangePi2GIOT/
> 2. Orange Pi i96 - https://www.96boards.org/product/orangepi-i96/
> 
> Cc: overseas.sales@unisoc.com
> Cc: zhao_steven@263.net
> Signed-off-by: Andreas Färber <afaerber@suse.de>
> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> ---
>  Documentation/devicetree/bindings/arm/rda.txt | 17 +++++++++++++++++
>  1 file changed, 17 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/arm/rda.txt
> 

Reviewed-by: Rob Herring <robh@kernel.org>

[PATCH v3 03/15] ARM: Prepare RDA8810PL SoC

[Manivannan Sadhasivam]

From: Andreas Färber <afaerber@suse.de>

Introduce ARCH_RDA and mach-rda for RDA Micro SoCs.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 arch/arm/Kconfig           | 2 ++
 arch/arm/Makefile          | 1 +
 arch/arm/mach-rda/Kconfig  | 7 +++++++
 arch/arm/mach-rda/Makefile | 1 +
 4 files changed, 11 insertions(+)
 create mode 100644 arch/arm/mach-rda/Kconfig
 create mode 100644 arch/arm/mach-rda/Makefile

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 91be74d8df65..084f0983e6b2 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -804,6 +804,8 @@ source "arch/arm/plat-pxa/Kconfig"
 
 source "arch/arm/mach-qcom/Kconfig"
 
+source "arch/arm/mach-rda/Kconfig"
+
 source "arch/arm/mach-realview/Kconfig"
 
 source "arch/arm/mach-rockchip/Kconfig"
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index 05a91d8b89f3..10056ccdb8be 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -202,6 +202,7 @@ machine-$(CONFIG_ARCH_ORION5X)		+= orion5x
 machine-$(CONFIG_ARCH_PICOXCELL)	+= picoxcell
 machine-$(CONFIG_ARCH_PXA)		+= pxa
 machine-$(CONFIG_ARCH_QCOM)		+= qcom
+machine-$(CONFIG_ARCH_RDA)		+= rda
 machine-$(CONFIG_ARCH_REALVIEW)		+= realview
 machine-$(CONFIG_ARCH_ROCKCHIP)		+= rockchip
 machine-$(CONFIG_ARCH_RPC)		+= rpc
diff --git a/arch/arm/mach-rda/Kconfig b/arch/arm/mach-rda/Kconfig
new file mode 100644
index 000000000000..dafab78d7aab
--- /dev/null
+++ b/arch/arm/mach-rda/Kconfig
@@ -0,0 +1,7 @@
+menuconfig ARCH_RDA
+	bool "RDA Micro SoCs"
+	depends on ARCH_MULTI_V7
+	select COMMON_CLK
+	select GENERIC_IRQ_CHIP
+	help
+	  This enables support for the RDA Micro 8810PL SoC family.
diff --git a/arch/arm/mach-rda/Makefile b/arch/arm/mach-rda/Makefile
new file mode 100644
index 000000000000..6bea3d3a2dd7
--- /dev/null
+++ b/arch/arm/mach-rda/Makefile
@@ -0,0 +1 @@
+obj- += dummy.o
-- 
2.17.1

[PATCH v3 04/15] dt-bindings: interrupt-controller: Document RDA8810PL intc

[Manivannan Sadhasivam]

Document interrupt controller in RDA Micro RDA8810PL SoC.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 .../interrupt-controller/rda,8810pl-intc.txt  | 61 +++++++++++++++++++
 1 file changed, 61 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/interrupt-controller/rda,8810pl-intc.txt

diff --git a/Documentation/devicetree/bindings/interrupt-controller/rda,8810pl-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/rda,8810pl-intc.txt
new file mode 100644
index 000000000000..e0062aebf025
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/rda,8810pl-intc.txt
@@ -0,0 +1,61 @@
+RDA Micro RDA8810PL Interrupt Controller
+
+The interrupt controller in RDA8810PL SoC is a custom interrupt controller
+which supports up to 32 interrupts.
+
+Required properties:
+
+- compatible: Should be "rda,8810pl-intc".
+- reg: Specifies base physical address of the registers set.
+- interrupt-controller: Identifies the node as an interrupt controller.
+- #interrupt-cells: Specifies the number of cells needed to encode an
+  interrupt source. The value shall be 2.
+
+The interrupt sources are as follows:
+
+ID	Name
+------------
+0:	PULSE_DUMMY
+1:	I2C
+2:	NAND_NFSC
+3:	SDMMC1
+4:	SDMMC2
+5:	SDMMC3
+6:	SPI1
+7:	SPI2
+8:	SPI3
+9:	UART1
+10:	UART2
+11:	UART3
+12:	GPIO1
+13:	GPIO2
+14:	GPIO3
+15:	KEYPAD
+16:	TIMER
+17:	TIMEROS
+18:	COMREG0
+19:	COMREG1
+20:	USB
+21:	DMC
+22:	DMA
+23:	CAMERA
+24:	GOUDA
+25:	GPU
+26:	VPU_JPG
+27:	VPU_HOST
+28:	VOC
+29:	AUIFC0
+30:	AUIFC1
+31:	L2CC
+
+Example:
+		apb@20800000 {
+			compatible = "simple-bus";
+			...
+			intc: interrupt-controller@0 {
+				compatible = "rda,8810pl-intc";
+				reg = <0x0 0x1000>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+		};
-- 
2.17.1

Re: [PATCH v3 04/15] dt-bindings: interrupt-controller: Document RDA8810PL intc

[Rob Herring]

On Wed, 28 Nov 2018 19:20:55 +0530, Manivannan Sadhasivam wrote:
> Document interrupt controller in RDA Micro RDA8810PL SoC.
> 
> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> ---
>  .../interrupt-controller/rda,8810pl-intc.txt  | 61 +++++++++++++++++++
>  1 file changed, 61 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/interrupt-controller/rda,8810pl-intc.txt
> 

Reviewed-by: Rob Herring <robh@kernel.org>

[PATCH v3 05/15] arm: dts: Add devicetree for RDA8810PL SoC

[Manivannan Sadhasivam]

Add initial device tree for RDA8810PL SoC from RDA Microelectronics.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 arch/arm/boot/dts/rda8810pl.dtsi | 86 ++++++++++++++++++++++++++++++++
 1 file changed, 86 insertions(+)
 create mode 100644 arch/arm/boot/dts/rda8810pl.dtsi

diff --git a/arch/arm/boot/dts/rda8810pl.dtsi b/arch/arm/boot/dts/rda8810pl.dtsi
new file mode 100644
index 000000000000..15547b138977
--- /dev/null
+++ b/arch/arm/boot/dts/rda8810pl.dtsi
@@ -0,0 +1,86 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * RDA8810PL SoC
+ *
+ * Copyright (c) 2017 Andreas Färber
+ * Copyright (c) 2018 Manivannan Sadhasivam
+ */
+
+/ {
+	compatible = "rda,8810pl";
+	interrupt-parent = <&intc>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a5";
+			reg = <0x0>;
+		};
+	};
+
+	sram@100000 {
+		compatible = "mmio-sram";
+		reg = <0x100000 0x10000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+	};
+
+	apb@20800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x20800000 0x100000>;
+
+		intc: interrupt-controller@0 {
+			compatible = "rda,8810pl-intc";
+			reg = <0x0 0x1000>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	apb@20900000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x20900000 0x100000>;
+	};
+
+	apb@20a00000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x20a00000 0x100000>;
+
+		uart1: serial@0 {
+			compatible = "rda,8810pl-uart";
+			reg = <0x0 0x1000>;
+			status = "disabled";
+		};
+
+		uart2: serial@10000 {
+			compatible = "rda,8810pl-uart";
+			reg = <0x10000 0x1000>;
+			status = "disabled";
+		};
+
+		uart3: serial@90000 {
+			compatible = "rda,8810pl-uart";
+			reg = <0x90000 0x1000>;
+			status = "disabled";
+		};
+	};
+
+	l2: cache-controller@21100000 {
+		compatible = "arm,pl310-cache";
+		reg = <0x21100000 0x1000>;
+		cache-unified;
+		cache-level = <2>;
+	};
+};
-- 
2.17.1

[PATCH v3 06/15] arm: dts: Add devicetree for OrangePi 2G IoT board

[Manivannan Sadhasivam]

Add initial devicetree support for OrangePi 2G IoT board from Xunlong.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 arch/arm/boot/dts/Makefile                    |  2 +
 .../boot/dts/rda8810pl-orangepi-2g-iot.dts    | 50 +++++++++++++++++++
 2 files changed, 52 insertions(+)
 create mode 100644 arch/arm/boot/dts/rda8810pl-orangepi-2g-iot.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b0e966d625b9..a0fdad8f10dd 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -806,6 +806,8 @@ dtb-$(CONFIG_ARCH_QCOM) += \
 	qcom-msm8974-sony-xperia-castor.dtb \
 	qcom-msm8974-sony-xperia-honami.dtb \
 	qcom-mdm9615-wp8548-mangoh-green.dtb
+dtb-$(CONFIG_ARCH_RDA) += \
+	rda8810pl-orangepi-2g-iot.dtb
 dtb-$(CONFIG_ARCH_REALVIEW) += \
 	arm-realview-pb1176.dtb \
 	arm-realview-pb11mp.dtb \
diff --git a/arch/arm/boot/dts/rda8810pl-orangepi-2g-iot.dts b/arch/arm/boot/dts/rda8810pl-orangepi-2g-iot.dts
new file mode 100644
index 000000000000..98e34248ae80
--- /dev/null
+++ b/arch/arm/boot/dts/rda8810pl-orangepi-2g-iot.dts
@@ -0,0 +1,50 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 Andreas Färber
+ * Copyright (c) 2018 Manivannan Sadhasivam
+ */
+
+/dts-v1/;
+
+#include "rda8810pl.dtsi"
+
+/ {
+	compatible = "xunlong,orangepi-2g-iot", "rda,8810pl";
+	model = "Orange Pi 2G-IoT";
+
+	aliases {
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial2:921600n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;
+	};
+
+	uart_clk: uart-clk {
+		compatible = "fixed-clock";
+		clock-frequency = <921600>;
+		#clock-cells = <0>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+	clocks = <&uart_clk>;
+};
+
+&uart2 {
+	status = "okay";
+	clocks = <&uart_clk>;
+};
+
+&uart3 {
+	status = "okay";
+	clocks = <&uart_clk>;
+};
-- 
2.17.1

[PATCH v3 07/15] arm: dts: Add devicetree for OrangePi i96 board

[Manivannan Sadhasivam]

Add initial devicetree for Orange Pi i96 board from Xunlong. It
is one of the 96Boards IoT Edition board.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 arch/arm/boot/dts/Makefile                   |  3 +-
 arch/arm/boot/dts/rda8810pl-orangepi-i96.dts | 50 ++++++++++++++++++++
 2 files changed, 52 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/rda8810pl-orangepi-i96.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index a0fdad8f10dd..cfb08ea33872 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -807,7 +807,8 @@ dtb-$(CONFIG_ARCH_QCOM) += \
 	qcom-msm8974-sony-xperia-honami.dtb \
 	qcom-mdm9615-wp8548-mangoh-green.dtb
 dtb-$(CONFIG_ARCH_RDA) += \
-	rda8810pl-orangepi-2g-iot.dtb
+	rda8810pl-orangepi-2g-iot.dtb \
+	rda8810pl-orangepi-i96.dtb
 dtb-$(CONFIG_ARCH_REALVIEW) += \
 	arm-realview-pb1176.dtb \
 	arm-realview-pb11mp.dtb \
diff --git a/arch/arm/boot/dts/rda8810pl-orangepi-i96.dts b/arch/arm/boot/dts/rda8810pl-orangepi-i96.dts
new file mode 100644
index 000000000000..728f76931b99
--- /dev/null
+++ b/arch/arm/boot/dts/rda8810pl-orangepi-i96.dts
@@ -0,0 +1,50 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 Andreas Färber
+ * Copyright (c) 2018 Manivannan Sadhasivam
+ */
+
+/dts-v1/;
+
+#include "rda8810pl.dtsi"
+
+/ {
+	compatible = "xunlong,orangepi-i96", "rda,8810pl";
+	model = "Orange Pi i96";
+
+	aliases {
+		serial0 = &uart2;
+		serial1 = &uart1;
+		serial2 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial2:921600n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;
+	};
+
+	uart_clk: uart-clk {
+		compatible = "fixed-clock";
+		clock-frequency = <921600>;
+		#clock-cells = <0>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+	clocks = <&uart_clk>;
+};
+
+&uart2 {
+	status = "okay";
+	clocks = <&uart_clk>;
+};
+
+&uart3 {
+	status = "okay";
+	clocks = <&uart_clk>;
+};
-- 
2.17.1

[PATCH v3 08/15] irqchip: Add RDA8810PL interrupt driver

[Manivannan Sadhasivam]

Add interrupt driver for RDA Micro RDA8810PL SoC.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 arch/arm/mach-rda/Kconfig      |   1 +
 drivers/irqchip/Kconfig        |   4 ++
 drivers/irqchip/Makefile       |   1 +
 drivers/irqchip/irq-rda-intc.c | 107 +++++++++++++++++++++++++++++++++
 4 files changed, 113 insertions(+)
 create mode 100644 drivers/irqchip/irq-rda-intc.c

diff --git a/arch/arm/mach-rda/Kconfig b/arch/arm/mach-rda/Kconfig
index dafab78d7aab..29012bc68ca4 100644
--- a/arch/arm/mach-rda/Kconfig
+++ b/arch/arm/mach-rda/Kconfig
@@ -3,5 +3,6 @@ menuconfig ARCH_RDA
 	depends on ARCH_MULTI_V7
 	select COMMON_CLK
 	select GENERIC_IRQ_CHIP
+	select RDA_INTC
 	help
 	  This enables support for the RDA Micro 8810PL SoC family.
diff --git a/drivers/irqchip/Kconfig b/drivers/irqchip/Kconfig
index 51a5ef0e96ed..9d54645870ad 100644
--- a/drivers/irqchip/Kconfig
+++ b/drivers/irqchip/Kconfig
@@ -195,6 +195,10 @@ config JCORE_AIC
 	help
 	  Support for the J-Core integrated AIC.
 
+config RDA_INTC
+	bool
+	select IRQ_DOMAIN
+
 config RENESAS_INTC_IRQPIN
 	bool
 	select IRQ_DOMAIN
diff --git a/drivers/irqchip/Makefile b/drivers/irqchip/Makefile
index 794c13d3ac3d..417108027e40 100644
--- a/drivers/irqchip/Makefile
+++ b/drivers/irqchip/Makefile
@@ -43,6 +43,7 @@ obj-$(CONFIG_IMGPDC_IRQ)		+= irq-imgpdc.o
 obj-$(CONFIG_IRQ_MIPS_CPU)		+= irq-mips-cpu.o
 obj-$(CONFIG_SIRF_IRQ)			+= irq-sirfsoc.o
 obj-$(CONFIG_JCORE_AIC)			+= irq-jcore-aic.o
+obj-$(CONFIG_RDA_INTC)			+= irq-rda-intc.o
 obj-$(CONFIG_RENESAS_INTC_IRQPIN)	+= irq-renesas-intc-irqpin.o
 obj-$(CONFIG_RENESAS_IRQC)		+= irq-renesas-irqc.o
 obj-$(CONFIG_VERSATILE_FPGA_IRQ)	+= irq-versatile-fpga.o
diff --git a/drivers/irqchip/irq-rda-intc.c b/drivers/irqchip/irq-rda-intc.c
new file mode 100644
index 000000000000..1176291fdef8
--- /dev/null
+++ b/drivers/irqchip/irq-rda-intc.c
@@ -0,0 +1,107 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * RDA8810PL SoC irqchip driver
+ *
+ * Copyright RDA Microelectronics Company Limited
+ * Copyright (c) 2017 Andreas Färber
+ * Copyright (c) 2018 Manivannan Sadhasivam
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/irqchip.h>
+#include <linux/irqdomain.h>
+#include <linux/of_address.h>
+
+#include <asm/exception.h>
+
+#define RDA_INTC_FINALSTATUS	0x00
+#define RDA_INTC_MASK_SET	0x08
+#define RDA_INTC_MASK_CLR	0x0c
+
+#define RDA_IRQ_MASK_ALL	0xFFFFFFFF
+
+#define RDA_NR_IRQS 32
+
+static void __iomem *rda_intc_base;
+static struct irq_domain *rda_irq_domain;
+
+static void rda_intc_mask_irq(struct irq_data *d)
+{
+	writel_relaxed(BIT(d->hwirq), rda_intc_base + RDA_INTC_MASK_CLR);
+}
+
+static void rda_intc_unmask_irq(struct irq_data *d)
+{
+	writel_relaxed(BIT(d->hwirq), rda_intc_base + RDA_INTC_MASK_SET);
+}
+
+static int rda_intc_set_type(struct irq_data *data, unsigned int flow_type)
+{
+	/* Hardware supports only level triggered interrupts */
+	if ((flow_type & (IRQF_TRIGGER_HIGH | IRQF_TRIGGER_LOW)) == flow_type)
+		return 0;
+
+	return -EINVAL;
+}
+
+static void __exception_irq_entry rda_handle_irq(struct pt_regs *regs)
+{
+	u32 stat = readl_relaxed(rda_intc_base + RDA_INTC_FINALSTATUS);
+	u32 hwirq;
+
+	while (stat) {
+		hwirq = __fls(stat);
+		handle_domain_irq(rda_irq_domain, hwirq, regs);
+		stat &= ~BIT(hwirq);
+	}
+}
+
+static struct irq_chip rda_irq_chip = {
+	.name		= "rda-intc",
+	.irq_mask	= rda_intc_mask_irq,
+	.irq_unmask	= rda_intc_unmask_irq,
+	.irq_set_type	= rda_intc_set_type,
+};
+
+static int rda_irq_map(struct irq_domain *d,
+		       unsigned int virq, irq_hw_number_t hw)
+{
+	irq_set_status_flags(virq, IRQ_LEVEL);
+	irq_set_chip_and_handler(virq, &rda_irq_chip, handle_level_irq);
+	irq_set_chip_data(virq, d->host_data);
+	irq_set_probe(virq);
+
+	return 0;
+}
+
+static const struct irq_domain_ops rda_irq_domain_ops = {
+	.map = rda_irq_map,
+	.xlate = irq_domain_xlate_onecell,
+};
+
+static int __init rda8810_intc_init(struct device_node *node,
+				    struct device_node *parent)
+{
+	rda_intc_base = of_io_request_and_map(node, 0, "rda-intc");
+	if (!rda_intc_base)
+		return -ENXIO;
+
+	/* Mask all interrupt sources */
+	writel_relaxed(RDA_IRQ_MASK_ALL, rda_intc_base + RDA_INTC_MASK_CLR);
+
+	rda_irq_domain = irq_domain_create_linear(&node->fwnode, RDA_NR_IRQS,
+						  &rda_irq_domain_ops,
+						  rda_intc_base);
+	if (!rda_irq_domain) {
+		iounmap(rda_intc_base);
+		return -ENOMEM;
+	}
+
+	set_handle_irq(rda_handle_irq);
+
+	return 0;
+}
+
+IRQCHIP_DECLARE(rda_intc, "rda,8810pl-intc", rda8810_intc_init);
-- 
2.17.1

Re: [PATCH v3 08/15] irqchip: Add RDA8810PL interrupt driver

[Marc Zyngier]

On 28/11/2018 13:50, Manivannan Sadhasivam wrote:
> Add interrupt driver for RDA Micro RDA8810PL SoC.
> 
> Signed-off-by: Andreas Färber <afaerber@suse.de>
> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>

Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>

Given the dependency on the platform Kconfig entry, how do you want this
to be merged?

Thanks,

	M.
-- 
Jazz is not dead. It just smells funny...

Re: [PATCH v3 08/15] irqchip: Add RDA8810PL interrupt driver

[Manivannan Sadhasivam]

Hi Marc,

On Mon, Dec 10, 2018 at 09:39:13AM +0000, Marc Zyngier wrote:
> On 28/11/2018 13:50, Manivannan Sadhasivam wrote:
> > Add interrupt driver for RDA Micro RDA8810PL SoC.
> > 
> > Signed-off-by: Andreas Färber <afaerber@suse.de>
> > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> 
> Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
> 
> Given the dependency on the platform Kconfig entry, how do you want this
> to be merged?
> 

Hmmm, I think I can just move the platform Kconfig change to SoC changes
in next revision so that you can apply the driver independently.

Regards,
Mani

> Thanks,
> 
> 	M.
> -- 
> Jazz is not dead. It just smells funny...

Re: [PATCH v3 08/15] irqchip: Add RDA8810PL interrupt driver

[Marc Zyngier]

On 10/12/2018 09:56, Manivannan Sadhasivam wrote:
> Hi Marc,
> 
> On Mon, Dec 10, 2018 at 09:39:13AM +0000, Marc Zyngier wrote:
>> On 28/11/2018 13:50, Manivannan Sadhasivam wrote:
>>> Add interrupt driver for RDA Micro RDA8810PL SoC.
>>>
>>> Signed-off-by: Andreas Färber <afaerber@suse.de>
>>> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
>>
>> Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
>>
>> Given the dependency on the platform Kconfig entry, how do you want this
>> to be merged?
>>
> 
> Hmmm, I think I can just move the platform Kconfig change to SoC changes
> in next revision so that you can apply the driver independently.
That would work for me.

Thanks,

	M.
-- 
Jazz is not dead. It just smells funny...

[PATCH v3 09/15] dt-bindings: timer: Document RDA8810PL SoC timer

[Manivannan Sadhasivam]

Document RDA Micro RDA8810PL SoC timer.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 .../bindings/timer/rda,8810pl-timer.txt       | 21 +++++++++++++++++++
 1 file changed, 21 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/timer/rda,8810pl-timer.txt

diff --git a/Documentation/devicetree/bindings/timer/rda,8810pl-timer.txt b/Documentation/devicetree/bindings/timer/rda,8810pl-timer.txt
new file mode 100644
index 000000000000..06cc2b00be12
--- /dev/null
+++ b/Documentation/devicetree/bindings/timer/rda,8810pl-timer.txt
@@ -0,0 +1,21 @@
+RDA Micro RDA8810PL Timer
+
+Required properties:
+- compatible      :  "rda,8810pl-timer"
+- reg             :  Offset and length of the register set for the device.
+- interrupts      :  Should contain the interrupts.
+- interrupt-names :  Valid names are: "hwtimer", "ostimer".
+                     See ../resource-names.txt
+
+Example:
+
+		apb@20900000 {
+			compatible = "simple-bus";
+			...
+			timer@10000 {
+				compatible = "rda,8810pl-timer";
+				reg = <0x10000 0x1000>;
+				interrupts = <16 IRQ_TYPE_LEVEL_HIGH>,
+					     <17 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "hwtimer", "ostimer";
+			};
-- 
2.17.1

Re: [PATCH v3 09/15] dt-bindings: timer: Document RDA8810PL SoC timer

[Rob Herring]

On Wed, Nov 28, 2018 at 07:21:00PM +0530, Manivannan Sadhasivam wrote:
> Document RDA Micro RDA8810PL SoC timer.
> 
> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> ---
>  .../bindings/timer/rda,8810pl-timer.txt       | 21 +++++++++++++++++++
>  1 file changed, 21 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/timer/rda,8810pl-timer.txt
> 
> diff --git a/Documentation/devicetree/bindings/timer/rda,8810pl-timer.txt b/Documentation/devicetree/bindings/timer/rda,8810pl-timer.txt
> new file mode 100644
> index 000000000000..06cc2b00be12
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/timer/rda,8810pl-timer.txt
> @@ -0,0 +1,21 @@
> +RDA Micro RDA8810PL Timer
> +
> +Required properties:
> +- compatible      :  "rda,8810pl-timer"
> +- reg             :  Offset and length of the register set for the device.
> +- interrupts      :  Should contain the interrupts.

How many?

> +- interrupt-names :  Valid names are: "hwtimer", "ostimer".

It's more than just valid names, but rather must be those 2 strings.

> +                     See ../resource-names.txt
> +
> +Example:
> +
> +		apb@20900000 {
> +			compatible = "simple-bus";
> +			...
> +			timer@10000 {
> +				compatible = "rda,8810pl-timer";
> +				reg = <0x10000 0x1000>;
> +				interrupts = <16 IRQ_TYPE_LEVEL_HIGH>,
> +					     <17 IRQ_TYPE_LEVEL_HIGH>;
> +				interrupt-names = "hwtimer", "ostimer";
> +			};
> -- 
> 2.17.1
> 

[PATCH v3 10/15] arm: dts: rda8810pl: Add timer support

[Manivannan Sadhasivam]

Add timer support for RDA Micro RDA8810PL SoC.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 arch/arm/boot/dts/rda8810pl.dtsi | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/arm/boot/dts/rda8810pl.dtsi b/arch/arm/boot/dts/rda8810pl.dtsi
index 15547b138977..84baa4c0a14c 100644
--- a/arch/arm/boot/dts/rda8810pl.dtsi
+++ b/arch/arm/boot/dts/rda8810pl.dtsi
@@ -6,6 +6,8 @@
  * Copyright (c) 2018 Manivannan Sadhasivam
  */
 
+#include <dt-bindings/interrupt-controller/irq.h>
+
 / {
 	compatible = "rda,8810pl";
 	interrupt-parent = <&intc>;
@@ -50,6 +52,14 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x0 0x20900000 0x100000>;
+
+		timer@10000 {
+			compatible = "rda,8810pl-timer";
+			reg = <0x10000 0x1000>;
+			interrupts = <16 IRQ_TYPE_LEVEL_HIGH>,
+				     <17 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hwtimer", "ostimer";
+		};
 	};
 
 	apb@20a00000 {
-- 
2.17.1

[PATCH v3 11/15] clocksource: Add clock driver for RDA8810PL SoC

[Manivannan Sadhasivam]

Add clock driver for RDA Micro RDA8810PL SoC supporting OSTIMER
and HWTIMER.

RDA8810PL has two independent timers: OSTIMER (56 bit) and HWTIMER
(64 bit). Each timer provides optional interrupt support. In this
driver, OSTIMER is used for clockevents and HWTIMER is used for
clocksource.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 arch/arm/mach-rda/Kconfig       |   1 +
 drivers/clocksource/Kconfig     |   8 ++
 drivers/clocksource/Makefile    |   1 +
 drivers/clocksource/timer-rda.c | 195 ++++++++++++++++++++++++++++++++
 4 files changed, 205 insertions(+)
 create mode 100644 drivers/clocksource/timer-rda.c

diff --git a/arch/arm/mach-rda/Kconfig b/arch/arm/mach-rda/Kconfig
index 29012bc68ca4..1ea753f57b2d 100644
--- a/arch/arm/mach-rda/Kconfig
+++ b/arch/arm/mach-rda/Kconfig
@@ -4,5 +4,6 @@ menuconfig ARCH_RDA
 	select COMMON_CLK
 	select GENERIC_IRQ_CHIP
 	select RDA_INTC
+	select RDA_TIMER
 	help
 	  This enables support for the RDA Micro 8810PL SoC family.
diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
index 55c77e44bb2d..598b592e03d7 100644
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -105,6 +105,14 @@ config OWL_TIMER
 	help
 	  Enables the support for the Actions Semi Owl timer driver.
 
+config RDA_TIMER
+	bool "RDA timer driver" if COMPILE_TEST
+	depends on GENERIC_CLOCKEVENTS
+	select CLKSRC_MMIO
+	select TIMER_OF
+	help
+	  Enables the support for the RDA Micro timer driver.
+
 config SUN4I_TIMER
 	bool "Sun4i timer driver" if COMPILE_TEST
 	depends on HAS_IOMEM
diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile
index dd9138104568..150020a90707 100644
--- a/drivers/clocksource/Makefile
+++ b/drivers/clocksource/Makefile
@@ -57,6 +57,7 @@ obj-$(CONFIG_OXNAS_RPS_TIMER)	+= timer-oxnas-rps.o
 obj-$(CONFIG_OWL_TIMER)		+= timer-owl.o
 obj-$(CONFIG_SPRD_TIMER)	+= timer-sprd.o
 obj-$(CONFIG_NPCM7XX_TIMER)	+= timer-npcm7xx.o
+obj-$(CONFIG_RDA_TIMER)		+= timer-rda.o
 
 obj-$(CONFIG_ARC_TIMERS)		+= arc_timer.o
 obj-$(CONFIG_ARM_ARCH_TIMER)		+= arm_arch_timer.o
diff --git a/drivers/clocksource/timer-rda.c b/drivers/clocksource/timer-rda.c
new file mode 100644
index 000000000000..fd1199c189bf
--- /dev/null
+++ b/drivers/clocksource/timer-rda.c
@@ -0,0 +1,195 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * RDA8810PL SoC timer driver
+ *
+ * Copyright RDA Microelectronics Company Limited
+ * Copyright (c) 2017 Andreas Färber
+ * Copyright (c) 2018 Manivannan Sadhasivam
+ *
+ * RDA8810PL has two independent timers: OSTIMER (56 bit) and HWTIMER (64 bit).
+ * Each timer provides optional interrupt support. In this driver, OSTIMER is
+ * used for clockevents and HWTIMER is used for clocksource.
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+
+#include "timer-of.h"
+
+#define RDA_OSTIMER_LOADVAL_L	0x000
+#define RDA_OSTIMER_CTRL	0x004
+#define RDA_HWTIMER_LOCKVAL_L	0x024
+#define RDA_HWTIMER_LOCKVAL_H	0x028
+#define RDA_TIMER_IRQ_MASK_SET	0x02c
+#define RDA_TIMER_IRQ_MASK_CLR	0x030
+#define RDA_TIMER_IRQ_CLR	0x034
+
+#define RDA_OSTIMER_CTRL_ENABLE		BIT(24)
+#define RDA_OSTIMER_CTRL_REPEAT		BIT(28)
+#define RDA_OSTIMER_CTRL_LOAD		BIT(30)
+
+#define RDA_TIMER_IRQ_MASK_OSTIMER	BIT(0)
+
+#define RDA_TIMER_IRQ_CLR_OSTIMER	BIT(0)
+
+static int rda_ostimer_start(void __iomem *base, bool periodic, u64 cycles)
+{
+	u32 ctrl, load_l;
+
+	load_l = (u32)cycles;
+	ctrl = ((cycles >> 32) & 0xffffff);
+	ctrl |= RDA_OSTIMER_CTRL_LOAD | RDA_OSTIMER_CTRL_ENABLE;
+	if (periodic)
+		ctrl |= RDA_OSTIMER_CTRL_REPEAT;
+
+	/* Enable ostimer interrupt first */
+	writel_relaxed(RDA_TIMER_IRQ_MASK_OSTIMER,
+		       base + RDA_TIMER_IRQ_MASK_SET);
+
+	/* Write low 32 bits first, high 24 bits are with ctrl */
+	writel_relaxed(load_l, base + RDA_OSTIMER_LOADVAL_L);
+	writel_relaxed(ctrl, base + RDA_OSTIMER_CTRL);
+
+	return 0;
+}
+
+static int rda_ostimer_stop(void __iomem *base)
+{
+	/* Disable ostimer interrupt first */
+	writel_relaxed(RDA_TIMER_IRQ_MASK_OSTIMER,
+		       base + RDA_TIMER_IRQ_MASK_CLR);
+
+	writel_relaxed(0, base + RDA_OSTIMER_CTRL);
+
+	return 0;
+}
+
+static int rda_ostimer_set_state_shutdown(struct clock_event_device *evt)
+{
+	struct timer_of *to = to_timer_of(evt);
+
+	rda_ostimer_stop(timer_of_base(to));
+
+	return 0;
+}
+
+static int rda_ostimer_set_state_oneshot(struct clock_event_device *evt)
+{
+	struct timer_of *to = to_timer_of(evt);
+
+	rda_ostimer_stop(timer_of_base(to));
+
+	return 0;
+}
+
+static int rda_ostimer_set_state_periodic(struct clock_event_device *evt)
+{
+	struct timer_of *to = to_timer_of(evt);
+	unsigned long cycles_per_jiffy;
+
+	rda_ostimer_stop(timer_of_base(to));
+
+	cycles_per_jiffy = ((unsigned long long)NSEC_PER_SEC / HZ *
+			     evt->mult) >> evt->shift;
+	rda_ostimer_start(timer_of_base(to), true, cycles_per_jiffy);
+
+	return 0;
+}
+
+static int rda_ostimer_tick_resume(struct clock_event_device *evt)
+{
+	return 0;
+}
+
+static int rda_ostimer_set_next_event(unsigned long evt,
+				      struct clock_event_device *ev)
+{
+	struct timer_of *to = to_timer_of(ev);
+
+	rda_ostimer_start(timer_of_base(to), false, evt);
+
+	return 0;
+}
+
+static irqreturn_t rda_ostimer_interrupt(int irq, void *dev_id)
+{
+	struct clock_event_device *evt = dev_id;
+	struct timer_of *to = to_timer_of(evt);
+
+	/* clear timer int */
+	writel_relaxed(RDA_TIMER_IRQ_CLR_OSTIMER,
+		       timer_of_base(to) + RDA_TIMER_IRQ_CLR);
+
+	if (evt->event_handler)
+		evt->event_handler(evt);
+
+	return IRQ_HANDLED;
+}
+
+static struct timer_of rda_ostimer_of = {
+	.flags = TIMER_OF_IRQ | TIMER_OF_BASE,
+
+	.clkevt = {
+		.name = "rda-ostimer",
+		.rating = 250,
+		.features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT |
+			    CLOCK_EVT_FEAT_DYNIRQ,
+		.set_state_shutdown = rda_ostimer_set_state_shutdown,
+		.set_state_oneshot = rda_ostimer_set_state_oneshot,
+		.set_state_periodic = rda_ostimer_set_state_periodic,
+		.tick_resume = rda_ostimer_tick_resume,
+		.set_next_event	= rda_ostimer_set_next_event,
+	},
+
+	.of_base = {
+		.name = "rda-timer",
+		.index = 0,
+	},
+
+	.of_irq = {
+		.name = "ostimer",
+		.handler = rda_ostimer_interrupt,
+		.flags = IRQF_TIMER,
+	},
+};
+
+static u64 rda_hwtimer_read(struct clocksource *cs)
+{
+	void __iomem *base = timer_of_base(&rda_ostimer_of);
+	u32 lo, hi;
+
+	/* Always read low 32 bits first */
+	do {
+		lo = readl_relaxed(base + RDA_HWTIMER_LOCKVAL_L);
+		hi = readl_relaxed(base + RDA_HWTIMER_LOCKVAL_H);
+	} while (hi != readl_relaxed(base + RDA_HWTIMER_LOCKVAL_H));
+
+	return ((u64)hi << 32) | lo;
+}
+
+static struct clocksource rda_hwtimer_clocksource = {
+	.name           = "rda-timer",
+	.rating         = 400,
+	.read           = rda_hwtimer_read,
+	.mask           = CLOCKSOURCE_MASK(64),
+	.flags          = CLOCK_SOURCE_IS_CONTINUOUS,
+};
+
+static int __init rda_timer_init(struct device_node *np)
+{
+	unsigned long rate = 2000000;
+	int ret;
+
+	ret = timer_of_init(np, &rda_ostimer_of);
+	if (ret)
+		return ret;
+
+	clocksource_register_hz(&rda_hwtimer_clocksource, rate);
+
+	clockevents_config_and_register(&rda_ostimer_of.clkevt, rate,
+					0x2, UINT_MAX);
+
+	return 0;
+}
+
+TIMER_OF_DECLARE(rda8810pl, "rda,8810pl-timer", rda_timer_init);
-- 
2.17.1

[PATCH v3 12/15] dt-bindings: serial: Document RDA Micro UART

[Manivannan Sadhasivam]

From: Andreas Färber <afaerber@suse.de>

Add an initial binding for the UART in RDA Micro RDA8810PL SoC.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 .../bindings/serial/rda,8810pl-uart.txt           | 15 +++++++++++++++
 1 file changed, 15 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/serial/rda,8810pl-uart.txt

diff --git a/Documentation/devicetree/bindings/serial/rda,8810pl-uart.txt b/Documentation/devicetree/bindings/serial/rda,8810pl-uart.txt
new file mode 100644
index 000000000000..ee03116d7415
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/rda,8810pl-uart.txt
@@ -0,0 +1,15 @@
+RDA Micro UART
+
+Required properties:
+- compatible :  "rda,8810pl-uart" for RDA8810PL SoCs.
+- reg        :  Offset and length of the register set for the device.
+- interrupts :  Should contain UART interrupt.
+
+
+Example:
+
+		uart2: serial@20a90000 {
+			compatible = "rda,8810pl-uart";
+			reg = <0x20a90000 0x1000>;
+			interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
+		};
-- 
2.17.1

Re: [PATCH v3 12/15] dt-bindings: serial: Document RDA Micro UART

[Rob Herring]

On Wed, Nov 28, 2018 at 07:21:03PM +0530, Manivannan Sadhasivam wrote:
> From: Andreas Färber <afaerber@suse.de>
> 
> Add an initial binding for the UART in RDA Micro RDA8810PL SoC.
> 
> Signed-off-by: Andreas Färber <afaerber@suse.de>
> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> ---
>  .../bindings/serial/rda,8810pl-uart.txt           | 15 +++++++++++++++
>  1 file changed, 15 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/serial/rda,8810pl-uart.txt
> 
> diff --git a/Documentation/devicetree/bindings/serial/rda,8810pl-uart.txt b/Documentation/devicetree/bindings/serial/rda,8810pl-uart.txt
> new file mode 100644
> index 000000000000..ee03116d7415
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/serial/rda,8810pl-uart.txt
> @@ -0,0 +1,15 @@
> +RDA Micro UART
> +
> +Required properties:
> +- compatible :  "rda,8810pl-uart" for RDA8810PL SoCs.
> +- reg        :  Offset and length of the register set for the device.
> +- interrupts :  Should contain UART interrupt.

Uarts generally need a clock.

> +
> +
> +Example:
> +
> +		uart2: serial@20a90000 {
> +			compatible = "rda,8810pl-uart";
> +			reg = <0x20a90000 0x1000>;
> +			interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
> +		};
> -- 
> 2.17.1
> 

[PATCH v3 13/15] arm: dts: rda8810pl: Add interrupt support for UART

[Manivannan Sadhasivam]

Add interrupt support for UART in RDA Micro RDA8810PL SoC.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 arch/arm/boot/dts/rda8810pl.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/rda8810pl.dtsi b/arch/arm/boot/dts/rda8810pl.dtsi
index 84baa4c0a14c..19cde895bf65 100644
--- a/arch/arm/boot/dts/rda8810pl.dtsi
+++ b/arch/arm/boot/dts/rda8810pl.dtsi
@@ -71,18 +71,21 @@
 		uart1: serial@0 {
 			compatible = "rda,8810pl-uart";
 			reg = <0x0 0x1000>;
+			interrupts = <9 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 		};
 
 		uart2: serial@10000 {
 			compatible = "rda,8810pl-uart";
 			reg = <0x10000 0x1000>;
+			interrupts = <10 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 		};
 
 		uart3: serial@90000 {
 			compatible = "rda,8810pl-uart";
 			reg = <0x90000 0x1000>;
+			interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 		};
 	};
-- 
2.17.1

[PATCH v3 14/15] tty: serial: Add RDA8810PL UART driver

[Manivannan Sadhasivam]

Add UART driver for RDA Micro RDA8810PL SoC.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 .../admin-guide/kernel-parameters.txt         |   6 +
 drivers/tty/serial/Kconfig                    |  19 +
 drivers/tty/serial/Makefile                   |   1 +
 drivers/tty/serial/rda-uart.c                 | 831 ++++++++++++++++++
 include/uapi/linux/serial_core.h              |   3 +
 5 files changed, 860 insertions(+)
 create mode 100644 drivers/tty/serial/rda-uart.c

diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt
index 81d1d5a74728..07078880f7fd 100644
--- a/Documentation/admin-guide/kernel-parameters.txt
+++ b/Documentation/admin-guide/kernel-parameters.txt
@@ -1020,6 +1020,12 @@
 			specified address. The serial port must already be
 			setup and configured. Options are not yet supported.
 
+		rda,<addr>
+			Start an early, polled-mode console on a serial port
+			of an RDA Micro SoC, such as RDA8810PL, at the
+			specified address. The serial port must already be
+			setup and configured. Options are not yet supported.
+
 		smh	Use ARM semihosting calls for early console.
 
 		s3c2410,<addr>
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 32886c304641..67b9bf3b500e 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -1529,6 +1529,25 @@ config SERIAL_OWL_CONSOLE
 	  Say 'Y' here if you wish to use Actions Semiconductor S500/S900 UART
 	  as the system console.
 
+config SERIAL_RDA
+	bool "RDA Micro serial port support"
+	depends on ARCH_RDA || COMPILE_TEST
+	select SERIAL_CORE
+	help
+	  This driver is for RDA8810PL SoC's UART.
+	  Say 'Y' here if you wish to use the on-board serial port.
+	  Otherwise, say 'N'.
+
+config SERIAL_RDA_CONSOLE
+	bool "Console on RDA Micro serial port"
+	depends on SERIAL_RDA=y
+	select SERIAL_CORE_CONSOLE
+	select SERIAL_EARLYCON
+	default y
+	help
+	  Say 'Y' here if you wish to use the RDA8810PL UART as the system
+	  console. Only earlycon is implemented currently.
+
 endmenu
 
 config SERIAL_MCTRL_GPIO
diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
index daac675612df..8c303736b7e8 100644
--- a/drivers/tty/serial/Makefile
+++ b/drivers/tty/serial/Makefile
@@ -89,6 +89,7 @@ obj-$(CONFIG_SERIAL_MVEBU_UART)	+= mvebu-uart.o
 obj-$(CONFIG_SERIAL_PIC32)	+= pic32_uart.o
 obj-$(CONFIG_SERIAL_MPS2_UART)	+= mps2-uart.o
 obj-$(CONFIG_SERIAL_OWL)	+= owl-uart.o
+obj-$(CONFIG_SERIAL_RDA)	+= rda-uart.o
 
 # GPIOLIB helpers for modem control lines
 obj-$(CONFIG_SERIAL_MCTRL_GPIO)	+= serial_mctrl_gpio.o
diff --git a/drivers/tty/serial/rda-uart.c b/drivers/tty/serial/rda-uart.c
new file mode 100644
index 000000000000..284623eefaeb
--- /dev/null
+++ b/drivers/tty/serial/rda-uart.c
@@ -0,0 +1,831 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * RDA8810PL serial device driver
+ *
+ * Copyright RDA Microelectronics Company Limited
+ * Copyright (c) 2017 Andreas Färber
+ * Copyright (c) 2018 Manivannan Sadhasivam
+ */
+
+#include <linux/clk.h>
+#include <linux/console.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/serial.h>
+#include <linux/serial_core.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+
+#define RDA_UART_PORT_NUM 3
+#define RDA_UART_DEV_NAME "ttyRDA"
+
+#define RDA_UART_CTRL		0x00
+#define RDA_UART_STATUS		0x04
+#define RDA_UART_RXTX_BUFFER	0x08
+#define RDA_UART_IRQ_MASK	0x0c
+#define RDA_UART_IRQ_CAUSE	0x10
+#define RDA_UART_IRQ_TRIGGERS	0x14
+#define RDA_UART_CMD_SET	0x18
+#define RDA_UART_CMD_CLR	0x1c
+
+/* UART_CTRL Bits */
+#define RDA_UART_ENABLE			BIT(0)
+#define RDA_UART_DBITS_8		BIT(1)
+#define RDA_UART_TX_SBITS_2		BIT(2)
+#define RDA_UART_PARITY_EN		BIT(3)
+#define RDA_UART_PARITY(x)		(((x) & 0x3) << 4)
+#define RDA_UART_PARITY_ODD		RDA_UART_PARITY(0)
+#define RDA_UART_PARITY_EVEN		RDA_UART_PARITY(1)
+#define RDA_UART_PARITY_SPACE		RDA_UART_PARITY(2)
+#define RDA_UART_PARITY_MARK		RDA_UART_PARITY(3)
+#define RDA_UART_DIV_MODE		BIT(20)
+#define RDA_UART_IRDA_EN		BIT(21)
+#define RDA_UART_DMA_EN			BIT(22)
+#define RDA_UART_FLOW_CNT_EN		BIT(23)
+#define RDA_UART_LOOP_BACK_EN		BIT(24)
+#define RDA_UART_RX_LOCK_ERR		BIT(25)
+#define RDA_UART_RX_BREAK_LEN(x)	(((x) & 0xf) << 28)
+
+/* UART_STATUS Bits */
+#define RDA_UART_RX_FIFO(x)		(((x) & 0x7f) << 0)
+#define RDA_UART_RX_FIFO_MASK		(0x7f << 0)
+#define RDA_UART_TX_FIFO(x)		(((x) & 0x1f) << 8)
+#define RDA_UART_TX_FIFO_MASK		(0x1f << 8)
+#define RDA_UART_TX_ACTIVE		BIT(14)
+#define RDA_UART_RX_ACTIVE		BIT(15)
+#define RDA_UART_RX_OVERFLOW_ERR	BIT(16)
+#define RDA_UART_TX_OVERFLOW_ERR	BIT(17)
+#define RDA_UART_RX_PARITY_ERR		BIT(18)
+#define RDA_UART_RX_FRAMING_ERR		BIT(19)
+#define RDA_UART_RX_BREAK_INT		BIT(20)
+#define RDA_UART_DCTS			BIT(24)
+#define RDA_UART_CTS			BIT(25)
+#define RDA_UART_DTR			BIT(28)
+#define RDA_UART_CLK_ENABLED		BIT(31)
+
+/* UART_RXTX_BUFFER Bits */
+#define RDA_UART_RX_DATA(x)		(((x) & 0xff) << 0)
+#define RDA_UART_TX_DATA(x)		(((x) & 0xff) << 0)
+
+/* UART_IRQ_MASK Bits */
+#define RDA_UART_TX_MODEM_STATUS	BIT(0)
+#define RDA_UART_RX_DATA_AVAILABLE	BIT(1)
+#define RDA_UART_TX_DATA_NEEDED		BIT(2)
+#define RDA_UART_RX_TIMEOUT		BIT(3)
+#define RDA_UART_RX_LINE_ERR		BIT(4)
+#define RDA_UART_TX_DMA_DONE		BIT(5)
+#define RDA_UART_RX_DMA_DONE		BIT(6)
+#define RDA_UART_RX_DMA_TIMEOUT		BIT(7)
+#define RDA_UART_DTR_RISE		BIT(8)
+#define RDA_UART_DTR_FALL		BIT(9)
+
+/* UART_IRQ_CAUSE Bits */
+#define RDA_UART_TX_MODEM_STATUS_U	BIT(16)
+#define RDA_UART_RX_DATA_AVAILABLE_U	BIT(17)
+#define RDA_UART_TX_DATA_NEEDED_U	BIT(18)
+#define RDA_UART_RX_TIMEOUT_U		BIT(19)
+#define RDA_UART_RX_LINE_ERR_U		BIT(20)
+#define RDA_UART_TX_DMA_DONE_U		BIT(21)
+#define RDA_UART_RX_DMA_DONE_U		BIT(22)
+#define RDA_UART_RX_DMA_TIMEOUT_U	BIT(23)
+#define RDA_UART_DTR_RISE_U		BIT(24)
+#define RDA_UART_DTR_FALL_U		BIT(25)
+
+/* UART_TRIGGERS Bits */
+#define RDA_UART_RX_TRIGGER(x)		(((x) & 0x1f) << 0)
+#define RDA_UART_TX_TRIGGER(x)		(((x) & 0xf) << 8)
+#define RDA_UART_AFC_LEVEL(x)		(((x) & 0x1f) << 16)
+
+/* UART_CMD_SET Bits */
+#define RDA_UART_RI			BIT(0)
+#define RDA_UART_DCD			BIT(1)
+#define RDA_UART_DSR			BIT(2)
+#define RDA_UART_TX_BREAK_CONTROL	BIT(3)
+#define RDA_UART_TX_FINISH_N_WAIT	BIT(4)
+#define RDA_UART_RTS			BIT(5)
+#define RDA_UART_RX_FIFO_RESET		BIT(6)
+#define RDA_UART_TX_FIFO_RESET		BIT(7)
+
+#define RDA_UART_TX_FIFO_SIZE	16
+
+static struct uart_driver rda_uart_driver;
+
+struct rda_uart_port {
+	struct uart_port port;
+	struct clk *clk;
+};
+
+#define to_rda_uart_port(port) container_of(port, struct rda_uart_port, port)
+
+static struct rda_uart_port *rda_uart_ports[RDA_UART_PORT_NUM];
+
+static inline void rda_uart_write(struct uart_port *port, u32 val,
+				  unsigned int off)
+{
+	writel(val, port->membase + off);
+}
+
+static inline u32 rda_uart_read(struct uart_port *port, unsigned int off)
+{
+	return readl(port->membase + off);
+}
+
+static unsigned int rda_uart_tx_empty(struct uart_port *port)
+{
+	unsigned long flags;
+	unsigned int ret;
+	u32 val;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	val = rda_uart_read(port, RDA_UART_STATUS);
+	ret = (val & RDA_UART_TX_FIFO_MASK) ? TIOCSER_TEMT : 0;
+
+	spin_unlock_irqrestore(&port->lock, flags);
+
+	return ret;
+}
+
+static unsigned int rda_uart_get_mctrl(struct uart_port *port)
+{
+	unsigned int mctrl = 0;
+	u32 cmd_set, status;
+
+	cmd_set = rda_uart_read(port, RDA_UART_CMD_SET);
+	status = rda_uart_read(port, RDA_UART_STATUS);
+	if (cmd_set & RDA_UART_RTS)
+		mctrl |= TIOCM_RTS;
+	if (!(status & RDA_UART_CTS))
+		mctrl |= TIOCM_CTS;
+
+	return mctrl;
+}
+
+static void rda_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+	u32 val;
+
+	if (mctrl & TIOCM_RTS) {
+		val = rda_uart_read(port, RDA_UART_CMD_SET);
+		rda_uart_write(port, (val | RDA_UART_RTS), RDA_UART_CMD_SET);
+	} else {
+		/* Clear RTS to stop to receive. */
+		val = rda_uart_read(port, RDA_UART_CMD_CLR);
+		rda_uart_write(port, (val | RDA_UART_RTS), RDA_UART_CMD_CLR);
+	}
+
+	val = rda_uart_read(port, RDA_UART_CTRL);
+
+	if (mctrl & TIOCM_LOOP)
+		val |= RDA_UART_LOOP_BACK_EN;
+	else
+		val &= ~RDA_UART_LOOP_BACK_EN;
+
+	rda_uart_write(port, val, RDA_UART_CTRL);
+}
+
+static void rda_uart_stop_tx(struct uart_port *port)
+{
+	u32 val;
+
+	val = rda_uart_read(port, RDA_UART_IRQ_MASK);
+	val &= ~RDA_UART_TX_DATA_NEEDED;
+	rda_uart_write(port, val, RDA_UART_IRQ_MASK);
+
+	val = rda_uart_read(port, RDA_UART_CMD_SET);
+	val |= RDA_UART_TX_FIFO_RESET;
+	rda_uart_write(port, val, RDA_UART_CMD_SET);
+}
+
+static void rda_uart_stop_rx(struct uart_port *port)
+{
+	u32 val;
+
+	val = rda_uart_read(port, RDA_UART_IRQ_MASK);
+	val &= ~(RDA_UART_RX_DATA_AVAILABLE | RDA_UART_RX_TIMEOUT);
+	rda_uart_write(port, val, RDA_UART_IRQ_MASK);
+
+	/* Read Rx buffer before reset to avoid Rx timeout interrupt */
+	val = rda_uart_read(port, RDA_UART_RXTX_BUFFER);
+
+	val = rda_uart_read(port, RDA_UART_CMD_SET);
+	val |= RDA_UART_RX_FIFO_RESET;
+	rda_uart_write(port, val, RDA_UART_CMD_SET);
+}
+
+static void rda_uart_start_tx(struct uart_port *port)
+{
+	u32 val;
+
+	if (uart_tx_stopped(port)) {
+		rda_uart_stop_tx(port);
+		return;
+	}
+
+	val = rda_uart_read(port, RDA_UART_IRQ_MASK);
+	val |= RDA_UART_TX_DATA_NEEDED;
+	rda_uart_write(port, val, RDA_UART_IRQ_MASK);
+}
+
+static void rda_uart_change_baudrate(struct rda_uart_port *rda_port,
+				     unsigned long baud)
+{
+	clk_set_rate(rda_port->clk, baud * 8);
+}
+
+static void rda_uart_set_termios(struct uart_port *port,
+				 struct ktermios *termios,
+				 struct ktermios *old)
+{
+	struct rda_uart_port *rda_port = to_rda_uart_port(port);
+	unsigned long flags;
+	unsigned int ctrl, cmd_set, cmd_clr, triggers;
+	unsigned int baud;
+	u32 irq_mask;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	baud = uart_get_baud_rate(port, termios, old, 9600, port->uartclk / 4);
+	rda_uart_change_baudrate(rda_port, baud);
+
+	ctrl = rda_uart_read(port, RDA_UART_CTRL);
+	cmd_set = rda_uart_read(port, RDA_UART_CMD_SET);
+	cmd_clr = rda_uart_read(port, RDA_UART_CMD_CLR);
+
+	switch (termios->c_cflag & CSIZE) {
+	case CS5:
+	case CS6:
+		dev_warn(port->dev, "bit size not supported, using 7 bits\n");
+		/* Fall through */
+	case CS7:
+		ctrl &= ~RDA_UART_DBITS_8;
+		break;
+	default:
+		ctrl |= RDA_UART_DBITS_8;
+		break;
+	}
+
+	/* stop bits */
+	if (termios->c_cflag & CSTOPB)
+		ctrl |= RDA_UART_TX_SBITS_2;
+	else
+		ctrl &= ~RDA_UART_TX_SBITS_2;
+
+	/* parity check */
+	if (termios->c_cflag & PARENB) {
+		ctrl |= RDA_UART_PARITY_EN;
+
+		/* Mark or Space parity */
+		if (termios->c_cflag & CMSPAR) {
+			if (termios->c_cflag & PARODD)
+				ctrl |= RDA_UART_PARITY_MARK;
+			else
+				ctrl |= RDA_UART_PARITY_SPACE;
+		} else if (termios->c_cflag & PARODD) {
+			ctrl |= RDA_UART_PARITY_ODD;
+		} else {
+			ctrl |= RDA_UART_PARITY_EVEN;
+		}
+	} else {
+		ctrl &= ~RDA_UART_PARITY_EN;
+	}
+
+	/* Hardware handshake (RTS/CTS) */
+	if (termios->c_cflag & CRTSCTS) {
+		ctrl   |= RDA_UART_FLOW_CNT_EN;
+		cmd_set |= RDA_UART_RTS;
+	} else {
+		ctrl   &= ~RDA_UART_FLOW_CNT_EN;
+		cmd_clr |= RDA_UART_RTS;
+	}
+
+	ctrl |= RDA_UART_ENABLE;
+	ctrl &= ~RDA_UART_DMA_EN;
+
+	triggers  = (RDA_UART_AFC_LEVEL(20) | RDA_UART_RX_TRIGGER(16));
+	irq_mask = rda_uart_read(port, RDA_UART_IRQ_MASK);
+	rda_uart_write(port, 0, RDA_UART_IRQ_MASK);
+
+	rda_uart_write(port, triggers, RDA_UART_IRQ_TRIGGERS);
+	rda_uart_write(port, ctrl, RDA_UART_CTRL);
+	rda_uart_write(port, cmd_set, RDA_UART_CMD_SET);
+	rda_uart_write(port, cmd_clr, RDA_UART_CMD_CLR);
+
+	rda_uart_write(port, irq_mask, RDA_UART_IRQ_MASK);
+
+	/* Don't rewrite B0 */
+	if (tty_termios_baud_rate(termios))
+		tty_termios_encode_baud_rate(termios, baud, baud);
+
+	/* update the per-port timeout */
+	uart_update_timeout(port, termios->c_cflag, baud);
+
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static void rda_uart_send_chars(struct uart_port *port)
+{
+	struct circ_buf *xmit = &port->state->xmit;
+	unsigned int ch;
+	u32 val;
+
+	if (uart_tx_stopped(port))
+		return;
+
+	if (port->x_char) {
+		while (!(rda_uart_read(port, RDA_UART_STATUS) &
+			 RDA_UART_TX_FIFO_MASK))
+			cpu_relax();
+
+		rda_uart_write(port, port->x_char, RDA_UART_RXTX_BUFFER);
+		port->icount.tx++;
+		port->x_char = 0;
+	}
+
+	while (rda_uart_read(port, RDA_UART_STATUS) & RDA_UART_TX_FIFO_MASK) {
+		if (uart_circ_empty(xmit))
+			break;
+
+		ch = xmit->buf[xmit->tail];
+		rda_uart_write(port, ch, RDA_UART_RXTX_BUFFER);
+		xmit->tail = (xmit->tail + 1) & (SERIAL_XMIT_SIZE - 1);
+		port->icount.tx++;
+	}
+
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+		uart_write_wakeup(port);
+
+	if (!uart_circ_empty(xmit)) {
+		/* Re-enable Tx FIFO interrupt */
+		val = rda_uart_read(port, RDA_UART_IRQ_MASK);
+		val |= RDA_UART_TX_DATA_NEEDED;
+		rda_uart_write(port, val, RDA_UART_IRQ_MASK);
+	}
+}
+
+static void rda_uart_receive_chars(struct uart_port *port)
+{
+	u32 status, val;
+
+	status = rda_uart_read(port, RDA_UART_STATUS);
+	while ((status & RDA_UART_RX_FIFO_MASK)) {
+		char flag = TTY_NORMAL;
+
+		if (status & RDA_UART_RX_PARITY_ERR) {
+			port->icount.parity++;
+			flag = TTY_PARITY;
+		}
+
+		if (status & RDA_UART_RX_FRAMING_ERR) {
+			port->icount.frame++;
+			flag = TTY_FRAME;
+		}
+
+		if (status & RDA_UART_RX_OVERFLOW_ERR) {
+			port->icount.overrun++;
+			flag = TTY_OVERRUN;
+		}
+
+		val = rda_uart_read(port, RDA_UART_RXTX_BUFFER);
+		val &= 0xff;
+
+		port->icount.rx++;
+		tty_insert_flip_char(&port->state->port, val, flag);
+
+		status = rda_uart_read(port, RDA_UART_STATUS);
+	}
+
+	spin_unlock(&port->lock);
+	tty_flip_buffer_push(&port->state->port);
+	spin_lock(&port->lock);
+}
+
+static irqreturn_t rda_interrupt(int irq, void *dev_id)
+{
+	struct uart_port *port = dev_id;
+	unsigned long flags;
+	u32 val, irq_mask;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	/* Clear IRQ cause */
+	val = rda_uart_read(port, RDA_UART_IRQ_CAUSE);
+	rda_uart_write(port, val, RDA_UART_IRQ_CAUSE);
+
+	if (val & (RDA_UART_RX_DATA_AVAILABLE | RDA_UART_RX_TIMEOUT))
+		rda_uart_receive_chars(port);
+
+	if (val & (RDA_UART_TX_DATA_NEEDED)) {
+		irq_mask = rda_uart_read(port, RDA_UART_IRQ_MASK);
+		irq_mask &= ~RDA_UART_TX_DATA_NEEDED;
+		rda_uart_write(port, irq_mask, RDA_UART_IRQ_MASK);
+
+		rda_uart_send_chars(port);
+	}
+
+	spin_unlock_irqrestore(&port->lock, flags);
+
+	return IRQ_HANDLED;
+}
+
+static int rda_uart_startup(struct uart_port *port)
+{
+	unsigned long flags;
+	int ret;
+	u32 val;
+
+	spin_lock_irqsave(&port->lock, flags);
+	rda_uart_write(port, 0, RDA_UART_IRQ_MASK);
+	spin_unlock_irqrestore(&port->lock, flags);
+
+	ret = request_irq(port->irq, rda_interrupt, IRQF_NO_SUSPEND,
+			  "rda-uart", port);
+	if (ret)
+		return ret;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	val = rda_uart_read(port, RDA_UART_CTRL);
+	val |= RDA_UART_ENABLE;
+	rda_uart_write(port, val, RDA_UART_CTRL);
+
+	/* enable rx interrupt */
+	val = rda_uart_read(port, RDA_UART_IRQ_MASK);
+	val |= (RDA_UART_RX_DATA_AVAILABLE | RDA_UART_RX_TIMEOUT);
+	rda_uart_write(port, val, RDA_UART_IRQ_MASK);
+
+	spin_unlock_irqrestore(&port->lock, flags);
+
+	return 0;
+}
+
+static void rda_uart_shutdown(struct uart_port *port)
+{
+	unsigned long flags;
+	u32 val;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	rda_uart_stop_tx(port);
+	rda_uart_stop_rx(port);
+
+	val = rda_uart_read(port, RDA_UART_CTRL);
+	val &= ~RDA_UART_ENABLE;
+	rda_uart_write(port, val, RDA_UART_CTRL);
+
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static const char *rda_uart_type(struct uart_port *port)
+{
+	return (port->type == PORT_RDA) ? "rda-uart" : NULL;
+}
+
+static int rda_uart_request_port(struct uart_port *port)
+{
+	struct platform_device *pdev = to_platform_device(port->dev);
+	struct resource *res;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res)
+		return -ENXIO;
+
+	if (!devm_request_mem_region(port->dev, port->mapbase,
+				     resource_size(res), dev_name(port->dev)))
+		return -EBUSY;
+
+	if (port->flags & UPF_IOREMAP) {
+		port->membase = devm_ioremap_nocache(port->dev, port->mapbase,
+						     resource_size(res));
+		if (!port->membase)
+			return -EBUSY;
+	}
+
+	return 0;
+}
+
+static void rda_uart_config_port(struct uart_port *port, int flags)
+{
+	unsigned long irq_flags;
+
+	if (flags & UART_CONFIG_TYPE) {
+		port->type = PORT_RDA;
+		rda_uart_request_port(port);
+	}
+
+	spin_lock_irqsave(&port->lock, irq_flags);
+
+	/* Clear mask, so no surprise interrupts. */
+	rda_uart_write(port, 0, RDA_UART_IRQ_MASK);
+
+	/* Clear status register */
+	rda_uart_write(port, 0, RDA_UART_STATUS);
+
+	spin_unlock_irqrestore(&port->lock, irq_flags);
+}
+
+static void rda_uart_release_port(struct uart_port *port)
+{
+	struct platform_device *pdev = to_platform_device(port->dev);
+	struct resource *res;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res)
+		return;
+
+	if (port->flags & UPF_IOREMAP) {
+		devm_release_mem_region(port->dev, port->mapbase,
+					resource_size(res));
+		devm_iounmap(port->dev, port->membase);
+		port->membase = NULL;
+	}
+}
+
+static int rda_uart_verify_port(struct uart_port *port,
+				struct serial_struct *ser)
+{
+	if (port->type != PORT_RDA)
+		return -EINVAL;
+
+	if (port->irq != ser->irq)
+		return -EINVAL;
+
+	return 0;
+}
+
+static const struct uart_ops rda_uart_ops = {
+	.tx_empty       = rda_uart_tx_empty,
+	.get_mctrl      = rda_uart_get_mctrl,
+	.set_mctrl      = rda_uart_set_mctrl,
+	.start_tx       = rda_uart_start_tx,
+	.stop_tx        = rda_uart_stop_tx,
+	.stop_rx        = rda_uart_stop_rx,
+	.startup        = rda_uart_startup,
+	.shutdown       = rda_uart_shutdown,
+	.set_termios    = rda_uart_set_termios,
+	.type           = rda_uart_type,
+	.request_port	= rda_uart_request_port,
+	.release_port	= rda_uart_release_port,
+	.config_port	= rda_uart_config_port,
+	.verify_port	= rda_uart_verify_port,
+};
+
+#ifdef CONFIG_SERIAL_RDA_CONSOLE
+
+static void rda_console_putchar(struct uart_port *port, int ch)
+{
+	if (!port->membase)
+		return;
+
+	while (!(rda_uart_read(port, RDA_UART_STATUS) & RDA_UART_TX_FIFO_MASK))
+		cpu_relax();
+
+	rda_uart_write(port, ch, RDA_UART_RXTX_BUFFER);
+}
+
+static void rda_uart_port_write(struct uart_port *port, const char *s,
+				u_int count)
+{
+	u32 old_irq_mask;
+	unsigned long flags;
+	int locked;
+
+	local_irq_save(flags);
+
+	if (port->sysrq) {
+		locked = 0;
+	} else if (oops_in_progress) {
+		locked = spin_trylock(&port->lock);
+	} else {
+		spin_lock(&port->lock);
+		locked = 1;
+	}
+
+	old_irq_mask = rda_uart_read(port, RDA_UART_IRQ_MASK);
+	rda_uart_write(port, 0, RDA_UART_IRQ_MASK);
+
+	uart_console_write(port, s, count, rda_console_putchar);
+
+	/* wait until all contents have been sent out */
+	while (!(rda_uart_read(port, RDA_UART_STATUS) & RDA_UART_TX_FIFO_MASK))
+		cpu_relax();
+
+	rda_uart_write(port, old_irq_mask, RDA_UART_IRQ_MASK);
+
+	if (locked)
+		spin_unlock(&port->lock);
+
+	local_irq_restore(flags);
+}
+
+static void rda_uart_console_write(struct console *co, const char *s,
+				   u_int count)
+{
+	struct rda_uart_port *rda_port;
+
+	rda_port = rda_uart_ports[co->index];
+	if (!rda_port)
+		return;
+
+	rda_uart_port_write(&rda_port->port, s, count);
+}
+
+static int rda_uart_console_setup(struct console *co, char *options)
+{
+	struct rda_uart_port *rda_port;
+	int baud = 921600;
+	int bits = 8;
+	int parity = 'n';
+	int flow = 'n';
+
+	if (co->index < 0 || co->index >= RDA_UART_PORT_NUM)
+		return -EINVAL;
+
+	rda_port = rda_uart_ports[co->index];
+	if (!rda_port || !rda_port->port.membase)
+		return -ENODEV;
+
+	if (options)
+		uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+	return uart_set_options(&rda_port->port, co, baud, parity, bits, flow);
+}
+
+static struct console rda_uart_console = {
+	.name = RDA_UART_DEV_NAME,
+	.write = rda_uart_console_write,
+	.device = uart_console_device,
+	.setup = rda_uart_console_setup,
+	.flags = CON_PRINTBUFFER,
+	.index = -1,
+	.data = &rda_uart_driver,
+};
+
+static int __init rda_uart_console_init(void)
+{
+	register_console(&rda_uart_console);
+
+	return 0;
+}
+console_initcall(rda_uart_console_init);
+
+static void rda_uart_early_console_write(struct console *co,
+					 const char *s,
+					 u_int count)
+{
+	struct earlycon_device *dev = co->data;
+
+	rda_uart_port_write(&dev->port, s, count);
+}
+
+static int __init
+rda_uart_early_console_setup(struct earlycon_device *device, const char *opt)
+{
+	if (!device->port.membase)
+		return -ENODEV;
+
+	device->con->write = rda_uart_early_console_write;
+
+	return 0;
+}
+
+OF_EARLYCON_DECLARE(rda, "rda,8810pl-uart",
+		    rda_uart_early_console_setup);
+
+#define RDA_UART_CONSOLE (&rda_uart_console)
+#else
+#define RDA_UART_CONSOLE NULL
+#endif /* CONFIG_SERIAL_RDA_CONSOLE */
+
+static struct uart_driver rda_uart_driver = {
+	.owner = THIS_MODULE,
+	.driver_name = "rda-uart",
+	.dev_name = RDA_UART_DEV_NAME,
+	.nr = RDA_UART_PORT_NUM,
+	.cons = RDA_UART_CONSOLE,
+};
+
+static const struct of_device_id rda_uart_dt_matches[] = {
+	{ .compatible = "rda,8810pl-uart" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, rda_uart_dt_matches);
+
+static int rda_uart_probe(struct platform_device *pdev)
+{
+	struct resource *res_mem;
+	struct rda_uart_port *rda_port;
+	int ret, irq;
+
+	if (pdev->dev.of_node)
+		pdev->id = of_alias_get_id(pdev->dev.of_node, "serial");
+
+	if (pdev->id < 0 || pdev->id >= RDA_UART_PORT_NUM) {
+		dev_err(&pdev->dev, "id %d out of range\n", pdev->id);
+		return -EINVAL;
+	}
+
+	res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res_mem) {
+		dev_err(&pdev->dev, "could not get mem\n");
+		return -ENODEV;
+	}
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(&pdev->dev, "could not get irq\n");
+		return irq;
+	}
+
+	if (rda_uart_ports[pdev->id]) {
+		dev_err(&pdev->dev, "port %d already allocated\n", pdev->id);
+		return -EBUSY;
+	}
+
+	rda_port = devm_kzalloc(&pdev->dev, sizeof(*rda_port), GFP_KERNEL);
+	if (!rda_port)
+		return -ENOMEM;
+
+	rda_port->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(rda_port->clk)) {
+		dev_err(&pdev->dev, "could not get clk\n");
+		return PTR_ERR(rda_port->clk);
+	}
+
+	rda_port->port.dev = &pdev->dev;
+	rda_port->port.regshift = 0;
+	rda_port->port.line = pdev->id;
+	rda_port->port.type = PORT_RDA;
+	rda_port->port.iotype = UPIO_MEM;
+	rda_port->port.mapbase = res_mem->start;
+	rda_port->port.irq = irq;
+	rda_port->port.uartclk = clk_get_rate(rda_port->clk);
+	if (rda_port->port.uartclk == 0) {
+		dev_err(&pdev->dev, "clock rate is zero\n");
+		return -EINVAL;
+	}
+	rda_port->port.flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP |
+			       UPF_LOW_LATENCY;
+	rda_port->port.x_char = 0;
+	rda_port->port.fifosize = RDA_UART_TX_FIFO_SIZE;
+	rda_port->port.ops = &rda_uart_ops;
+
+	rda_uart_ports[pdev->id] = rda_port;
+	platform_set_drvdata(pdev, rda_port);
+
+	ret = uart_add_one_port(&rda_uart_driver, &rda_port->port);
+	if (ret)
+		rda_uart_ports[pdev->id] = NULL;
+
+	return ret;
+}
+
+static int rda_uart_remove(struct platform_device *pdev)
+{
+	struct rda_uart_port *rda_port = platform_get_drvdata(pdev);
+
+	uart_remove_one_port(&rda_uart_driver, &rda_port->port);
+	rda_uart_ports[pdev->id] = NULL;
+
+	return 0;
+}
+
+static struct platform_driver rda_uart_platform_driver = {
+	.probe = rda_uart_probe,
+	.remove = rda_uart_remove,
+	.driver = {
+		.name = "rda-uart",
+		.of_match_table = rda_uart_dt_matches,
+	},
+};
+
+static int __init rda_uart_init(void)
+{
+	int ret;
+
+	ret = uart_register_driver(&rda_uart_driver);
+	if (ret)
+		return ret;
+
+	ret = platform_driver_register(&rda_uart_platform_driver);
+	if (ret)
+		uart_unregister_driver(&rda_uart_driver);
+
+	return ret;
+}
+
+static void __init rda_uart_exit(void)
+{
+	platform_driver_unregister(&rda_uart_platform_driver);
+	uart_unregister_driver(&rda_uart_driver);
+}
+
+module_init(rda_uart_init);
+module_exit(rda_uart_exit);
+
+MODULE_AUTHOR("Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>");
+MODULE_DESCRIPTION("RDA8810PL serial device driver");
+MODULE_LICENSE("GPL");
diff --git a/include/uapi/linux/serial_core.h b/include/uapi/linux/serial_core.h
index dce5f9dae121..df4a7534e239 100644
--- a/include/uapi/linux/serial_core.h
+++ b/include/uapi/linux/serial_core.h
@@ -281,4 +281,7 @@
 /* MediaTek BTIF */
 #define PORT_MTK_BTIF	117
 
+/* RDA UART */
+#define PORT_RDA	118
+
 #endif /* _UAPILINUX_SERIAL_CORE_H */
-- 
2.17.1

[PATCH v3 15/15] MAINTAINERS: Add entry for RDA Micro SoC architecture

[Manivannan Sadhasivam]

Add MAINTAINERS entry for RDA Micro SoC architecture with myself
and Andreas Färber as the maintainers.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 MAINTAINERS | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index 6c3fbbb361f8..7a5ae685a638 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1945,6 +1945,20 @@ M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 
+ARM/RDA MICRO ARCHITECTURE
+M:	Andreas Färber <afaerber@suse.de>
+M:	Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+S:	Maintained
+F:	arch/arm/boot/dts/rda8810pl-*
+F:	drivers/clocksource/timer-rda.c
+F:	drivers/irqchip/irq-rda-intc.c
+F:	drivers/tty/serial/rda-uart.c
+F:	Documentation/devicetree/bindings/arm/rda.txt
+F:	Documentation/devicetree/bindings/interrupt-controller/rda,8810pl-intc.txt
+F:	Documentation/devicetree/bindings/serial/rda,8810pl-uart.txt
+F:	Documentation/devicetree/bindings/timer/rda,8810pl-timer.txt
+
 ARM/REALTEK ARCHITECTURE
 M:	Andreas Färber <afaerber@suse.de>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-- 
2.17.1