* [PATCH v3 2/2] arm64: dts: Add support for NXP LS1028A SoC
2018-11-14 5:30 [PATCH v3 1/2] dt-bindings: Add compatible string for LS1028A-QDS Bhaskar Upadhaya
@ 2018-11-14 5:30 ` Bhaskar Upadhaya
2018-11-26 14:42 ` Shawn Guo
2018-11-28 2:41 ` [PATCH v3 1/2] dt-bindings: Add compatible string for LS1028A-QDS Shawn Guo
1 sibling, 1 reply; 6+ messages in thread
From: Bhaskar Upadhaya @ 2018-11-14 5:30 UTC (permalink / raw)
To: devicetree@vger.kernel.org, shawnguo@kernel.org
Cc: Harninder Rai, Sudhanshu Gupta,
linux-arm-kernel@lists.infradead.org, Leo Li
LS1028A contains two ARM v8 CortexA72 processor cores
with 32 KB L1-D cache and 48 KB L1-I cache
Features summary
Two 32-bit / 64-bit ARM v8 Cortex-A72 CPUs
- Arranged as single clusters of two cores sharing a 1 MB L2 cache
- Speed Up to 1.3 GHz
- Support for cluster power-gating.
Cache coherent interconnect (CCI-400)
- Hardware-managed data coherency
- Up to 400 MHz
32-bit DDR4 SDRAM memory controller with ECC
Two PCIe 3.0 controllers
One serial ATA (SATA 3.0) controller
Two high-speed USB 3.0 controllers with integrated PHY
Following levels of DTSI/DTS files have been created for the LS1028A
SoC family:
- fsl-ls1028a.dtsi:
DTS-Include file for NXP LS1028A SoC.
- fsl-ls1028a-qds.dts:
DTS file for NXP LS1028A QDS board.
- fsl-ls1028a-rdb.dts:
DTS file for NXP LS1028A RDB board
Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@nxp.com>
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
---
changes in v3:
- provide spaces between child node and property
- move memory node from silicon file to board level DTS
- use macro IRQ_TYPE_LEVEL_HIGH instead of numbers
arch/arm64/boot/dts/freescale/Makefile | 2 +
arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts | 93 ++++++
arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts | 73 +++++
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 339 ++++++++++++++++++++++
4 files changed, 507 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 9a88530..7748e6d 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -3,6 +3,8 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-frdm.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-frwy.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-rdb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-rdb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-rdb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-qds.dtb
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
new file mode 100644
index 0000000..14c79f4
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
@@ -0,0 +1,93 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for NXP LS1028A QDS Board.
+ *
+ * Copyright 2018 NXP
+ *
+ * Harninder Rai <harninder.rai@nxp.com>
+ *
+ */
+
+/dts-v1/;
+
+#include "fsl-ls1028a.dtsi"
+
+/ {
+ model = "LS1028A QDS Board";
+ compatible = "fsl,ls1028a-qds", "fsl,ls1028a";
+
+ aliases {
+ gpio0 = &gpio1;
+ gpio1 = &gpio2;
+ gpio2 = &gpio3;
+ serial0 = &duart0;
+ serial1 = &duart1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x0 0x80000000 0x1 0x00000000>;
+ };
+};
+
+&duart0 {
+ status = "okay";
+};
+
+&duart1 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ i2c-mux@77 {
+ compatible = "nxp,pca9847";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x2>;
+
+ current-monitor@40 {
+ compatible = "ti,ina220";
+ reg = <0x40>;
+ shunt-resistor = <1000>;
+ };
+
+ current-monitor@41 {
+ compatible = "ti,ina220";
+ reg = <0x41>;
+ shunt-resistor = <1000>;
+ };
+ };
+
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x3>;
+
+ rtc@51 {
+ compatible = "nxp,pcf2129";
+ reg = <0x51>;
+ };
+
+ eeprom@56 {
+ compatible = "atmel,24c512";
+ reg = <0x56>;
+ };
+
+ eeprom@57 {
+ compatible = "atmel,24c512";
+ reg = <0x57>;
+ };
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
new file mode 100644
index 0000000..fdeb417
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
@@ -0,0 +1,73 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for NXP LS1028A RDB Board.
+ *
+ * Copyright 2018 NXP
+ *
+ * Harninder Rai <harninder.rai@nxp.com>
+ *
+ */
+
+/dts-v1/;
+#include "fsl-ls1028a.dtsi"
+
+/ {
+ model = "LS1028A RDB Board";
+ compatible = "fsl,ls1028a-rdb", "fsl,ls1028a";
+
+ aliases {
+ serial0 = &duart0;
+ serial1 = &duart1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x0 0x80000000 0x1 0x0000000>;
+ };
+};
+
+&i2c0 {
+ status = "okay";
+
+ i2c-mux@77 {
+ compatible = "nxp,pca9847";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x02>;
+
+ current-monitor@40 {
+ compatible = "ti,ina220";
+ reg = <0x40>;
+ shunt-resistor = <500>;
+ };
+ };
+
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x3>;
+
+ rtc@51 {
+ compatible = "nxp,pcf2129";
+ reg = <0x51>;
+ };
+ };
+ };
+};
+
+&duart0 {
+ status = "okay";
+};
+
+&duart1 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
new file mode 100644
index 0000000..a8cf92a
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
@@ -0,0 +1,339 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree Include file for NXP Layerscape-1028A family SoC.
+ *
+ * Copyright 2018 NXP
+ *
+ * Harninder Rai <harninder.rai@nxp.com>
+ *
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+ compatible = "fsl,ls1028a";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72";
+ reg = <0x0>;
+ enable-method = "psci";
+ clocks = <&clockgen 1 0>;
+ next-level-cache = <&l2>;
+ cpu-idle-states = <&CPU_PH20>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72";
+ reg = <0x1>;
+ enable-method = "psci";
+ clocks = <&clockgen 1 0>;
+ next-level-cache = <&l2>;
+ cpu-idle-states = <&CPU_PH20>;
+ };
+
+ l2: l2-cache {
+ compatible = "cache";
+ };
+ };
+
+ idle-states {
+ /*
+ * PSCI node is not added default, U-boot will add missing
+ * parts if it determines to use PSCI.
+ */
+ entry-method = "arm,psci";
+
+ CPU_PH20: cpu-ph20 {
+ compatible = "arm,idle-state";
+ idle-state-name = "PH20";
+ arm,psci-suspend-param = <0x00010000>;
+ entry-latency-us = <1000>;
+ exit-latency-us = <1000>;
+ min-residency-us = <3000>;
+ };
+ };
+
+ sysclk: clock-sysclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ clock-output-names = "sysclk";
+ };
+
+ reboot {
+ compatible ="syscon-reboot";
+ regmap = <&dcfg>;
+ offset = <0xb0>;
+ mask = <0x02>;
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
+ IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) |
+ IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) |
+ IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) |
+ IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ gic: interrupt-controller@6000000 {
+ compatible= "arm,gic-v3";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ reg= <0x0 0x06000000 0 0x10000>, /* GIC Dist */
+ <0x0 0x06040000 0 0x40000>; /* GIC Redistributor */
+ #interrupt-cells= <3>;
+ interrupt-controller;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_RAW(0xf) |
+ IRQ_TYPE_LEVEL_LOW)>;
+ its: gic-its@6020000 {
+ compatible = "arm,gic-v3-its";
+ msi-controller;
+ reg = <0x0 0x06020000 0 0x20000>;/* GIC Translater */
+ };
+ };
+
+ soc: soc {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ ddr: memory-controller@1080000 {
+ compatible = "fsl,qoriq-memory-controller";
+ reg = <0x0 0x1080000 0x0 0x1000>;
+ interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
+ big-endian;
+ };
+
+ dcfg: syscon@1e00000 {
+ compatible = "fsl,ls1028a-dcfg", "syscon";
+ reg = <0x0 0x1e00000 0x0 0x10000>;
+ big-endian;
+ };
+
+ scfg: syscon@1fc0000 {
+ compatible = "fsl,ls1028a-scfg", "syscon";
+ reg = <0x0 0x1fc0000 0x0 0x10000>;
+ big-endian;
+ };
+
+ clockgen: clock-controller@1300000 {
+ compatible = "fsl,ls1028a-clockgen";
+ reg = <0x0 0x1300000 0x0 0xa0000>;
+ #clock-cells = <2>;
+ clocks = <&sysclk>;
+ };
+
+ i2c0: i2c@2000000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2000000 0x0 0x10000>;
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 1>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@2010000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2010000 0x0 0x10000>;
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 1>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@2020000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2020000 0x0 0x10000>;
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 1>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@2030000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2030000 0x0 0x10000>;
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 1>;
+ status = "disabled";
+ };
+
+ i2c4: i2c@2040000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2040000 0x0 0x10000>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 1>;
+ status = "disabled";
+ };
+
+ i2c5: i2c@2050000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2050000 0x0 0x10000>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 1>;
+ status = "disabled";
+ };
+
+ i2c6: i2c@2060000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2060000 0x0 0x10000>;
+ interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 1>;
+ status = "disabled";
+ };
+
+ i2c7: i2c@2070000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2070000 0x0 0x10000>;
+ interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 1>;
+ status = "disabled";
+ };
+
+ duart0: serial@21c0500 {
+ compatible = "fsl,ns16550", "ns16550a";
+ reg = <0x00 0x21c0500 0x0 0x100>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 1>;
+ status = "disabled";
+ };
+
+ duart1: serial@21c0600 {
+ compatible = "fsl,ns16550", "ns16550a";
+ reg = <0x00 0x21c0600 0x0 0x100>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 1>;
+ status = "disabled";
+ };
+
+ gpio1: gpio@2300000 {
+ compatible = "fsl,qoriq-gpio";
+ reg = <0x0 0x2300000 0x0 0x10000>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio2: gpio@2310000 {
+ compatible = "fsl,qoriq-gpio";
+ reg = <0x0 0x2310000 0x0 0x10000>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio3: gpio@2320000 {
+ compatible = "fsl,qoriq-gpio";
+ reg = <0x0 0x2320000 0x0 0x10000>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ wdog0: watchdog@23c0000 {
+ compatible = "fsl,ls1028a-wdt", "fsl,imx21-wdt";
+ reg = <0x0 0x23c0000 0x0 0x10000>;
+ interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 1>;
+ big-endian;
+ status = "disabled";
+ };
+
+ sata: sata@3200000 {
+ compatible = "fsl,ls1028a-ahci";
+ reg = <0x0 0x3200000 0x0 0x10000>,
+ <0x0 0x20140520 0x0 0x4>;
+ reg-names = "ahci", "sata-ecc";
+ interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 1>;
+ status = "disabled";
+ };
+
+ smmu: iommu@5000000 {
+ compatible = "arm,mmu-500";
+ reg = <0 0x5000000 0 0x800000>;
+ #global-interrupts = <8>;
+ #iommu-cells = <1>;
+ stream-match-mask = <0x7c00>;
+ /* global secure fault */
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+ /* combined secure interrupt */
+ <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+ /* global non-secure fault */
+ <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+ /* combined non-secure interrupt */
+ <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+ /* performance counter interrupts 0-7 */
+ <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>,
+ /* per context interrupt, 64 interrupts */
+ <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+};
--
1.9.1
^ permalink raw reply related [flat|nested] 6+ messages in thread