* [PATCH v4 2/4] usb: chipidea: imx: add HSIC support
2018-12-09 5:40 [PATCH v4 0/4] usb: chipidea: imx: add HSIC support Peter Chen
2018-12-09 5:40 ` [PATCH v4 1/4] usb: chipidea: add flag for imx hsic implementation Peter Chen
@ 2018-12-09 5:40 ` Peter Chen
2018-12-09 5:40 ` [PATCH v4 3/4] usb: chipidea: host: override ehci->hub_control Peter Chen
2018-12-09 5:40 ` [PATCH v4 4/4] doc: usb: ci-hdrc-usb2: Add pinctrl properties for HSIC pin groups Peter Chen
3 siblings, 0 replies; 8+ messages in thread
From: Peter Chen @ 2018-12-09 5:40 UTC (permalink / raw)
To: linux-usb@vger.kernel.org
Cc: dl-linux-imx, robh+dt@kernel.org, devicetree@vger.kernel.org,
frieder.schrempf@exceet.de, festevam@gmail.com, Peter Chen
To support imx HSIC, there are some special requirement:
- The HSIC pad is 1.2v, it may need to supply from external
- The data/strobe pin needs to be pulled down first, and after
host mode is initialized, the strobe pin needs to be pulled up
- During the USB suspend/resume, special setting is needed
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
---
drivers/usb/chipidea/ci_hdrc_imx.c | 140 ++++++++++++++++++++++++++++++++-----
drivers/usb/chipidea/ci_hdrc_imx.h | 9 ++-
drivers/usb/chipidea/usbmisc_imx.c | 140 +++++++++++++++++++++++++++++++++++++
3 files changed, 270 insertions(+), 19 deletions(-)
diff --git a/drivers/usb/chipidea/ci_hdrc_imx.c b/drivers/usb/chipidea/ci_hdrc_imx.c
index 09b37c0d075d..56781c329db0 100644
--- a/drivers/usb/chipidea/ci_hdrc_imx.c
+++ b/drivers/usb/chipidea/ci_hdrc_imx.c
@@ -14,6 +14,7 @@
#include <linux/usb/chipidea.h>
#include <linux/usb/of.h>
#include <linux/clk.h>
+#include <linux/pinctrl/consumer.h>
#include "ci.h"
#include "ci_hdrc_imx.h"
@@ -85,6 +86,9 @@ struct ci_hdrc_imx_data {
bool supports_runtime_pm;
bool override_phy_control;
bool in_lpm;
+ struct pinctrl *pinctrl;
+ struct pinctrl_state *pinctrl_hsic_active;
+ struct regulator *hsic_pad_regulator;
/* SoC before i.mx6 (except imx23/imx28) needs three clks */
bool need_three_clks;
struct clk *clk_ipg;
@@ -245,19 +249,49 @@ static void imx_disable_unprepare_clks(struct device *dev)
}
}
+static int ci_hdrc_imx_notify_event(struct ci_hdrc *ci, unsigned int event)
+{
+ struct device *dev = ci->dev->parent;
+ struct ci_hdrc_imx_data *data = dev_get_drvdata(dev);
+ int ret = 0;
+
+ switch (event) {
+ case CI_HDRC_IMX_HSIC_ACTIVE_EVENT:
+ ret = pinctrl_select_state(data->pinctrl,
+ data->pinctrl_hsic_active);
+ if (ret)
+ dev_err(dev, "hsic_active select failed, err=%d\n",
+ ret);
+ break;
+ case CI_HDRC_IMX_HSIC_SUSPEND_EVENT:
+ ret = imx_usbmisc_hsic_set_connect(data->usbmisc_data);
+ if (ret)
+ dev_err(dev,
+ "hsic_set_connect failed, err=%d\n", ret);
+ break;
+ default:
+ break;
+ }
+
+ return ret;
+}
+
static int ci_hdrc_imx_probe(struct platform_device *pdev)
{
struct ci_hdrc_imx_data *data;
struct ci_hdrc_platform_data pdata = {
.name = dev_name(&pdev->dev),
.capoffset = DEF_CAPOFFSET,
+ .notify_event = ci_hdrc_imx_notify_event,
};
int ret;
const struct of_device_id *of_id;
const struct ci_hdrc_imx_platform_flag *imx_platform_flag;
struct device_node *np = pdev->dev.of_node;
+ struct device *dev = &pdev->dev;
+ struct pinctrl_state *pinctrl_hsic_idle;
- of_id = of_match_device(ci_hdrc_imx_dt_ids, &pdev->dev);
+ of_id = of_match_device(ci_hdrc_imx_dt_ids, dev);
if (!of_id)
return -ENODEV;
@@ -268,19 +302,73 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev)
return -ENOMEM;
platform_set_drvdata(pdev, data);
- data->usbmisc_data = usbmisc_get_init_data(&pdev->dev);
+ data->usbmisc_data = usbmisc_get_init_data(dev);
if (IS_ERR(data->usbmisc_data))
return PTR_ERR(data->usbmisc_data);
- ret = imx_get_clks(&pdev->dev);
+ if (of_usb_get_phy_mode(dev->of_node) == USBPHY_INTERFACE_MODE_HSIC) {
+ pdata.flags |= CI_HDRC_IMX_IS_HSIC;
+ data->usbmisc_data->hsic = 1;
+ data->pinctrl = devm_pinctrl_get(dev);
+ if (IS_ERR(data->pinctrl)) {
+ dev_err(dev, "pinctrl get failed, err=%ld\n",
+ PTR_ERR(data->pinctrl));
+ return PTR_ERR(data->pinctrl);
+ }
+
+ pinctrl_hsic_idle = pinctrl_lookup_state(data->pinctrl, "idle");
+ if (IS_ERR(pinctrl_hsic_idle)) {
+ dev_err(dev,
+ "pinctrl_hsic_idle lookup failed, err=%ld\n",
+ PTR_ERR(pinctrl_hsic_idle));
+ return PTR_ERR(pinctrl_hsic_idle);
+ }
+
+ ret = pinctrl_select_state(data->pinctrl, pinctrl_hsic_idle);
+ if (ret) {
+ dev_err(dev, "hsic_idle select failed, err=%d\n", ret);
+ return ret;
+ }
+
+ data->pinctrl_hsic_active = pinctrl_lookup_state(data->pinctrl,
+ "active");
+ if (IS_ERR(data->pinctrl_hsic_active)) {
+ dev_err(dev,
+ "pinctrl_hsic_active lookup failed, err=%ld\n",
+ PTR_ERR(data->pinctrl_hsic_active));
+ return PTR_ERR(data->pinctrl_hsic_active);
+ }
+
+ data->hsic_pad_regulator = devm_regulator_get(dev, "hsic");
+ if (PTR_ERR(data->hsic_pad_regulator) == -EPROBE_DEFER) {
+ return -EPROBE_DEFER;
+ } else if (PTR_ERR(data->hsic_pad_regulator) == -ENODEV) {
+ /* no pad regualator is needed */
+ data->hsic_pad_regulator = NULL;
+ } else if (IS_ERR(data->hsic_pad_regulator)) {
+ dev_err(dev, "Get HSIC pad regulator error: %ld\n",
+ PTR_ERR(data->hsic_pad_regulator));
+ return PTR_ERR(data->hsic_pad_regulator);
+ }
+
+ if (data->hsic_pad_regulator) {
+ ret = regulator_enable(data->hsic_pad_regulator);
+ if (ret) {
+ dev_err(dev,
+ "Failed to enable HSIC pad regulator\n");
+ return ret;
+ }
+ }
+ }
+ ret = imx_get_clks(dev);
if (ret)
- return ret;
+ goto disable_hsic_regulator;
- ret = imx_prepare_enable_clks(&pdev->dev);
+ ret = imx_prepare_enable_clks(dev);
if (ret)
- return ret;
+ goto disable_hsic_regulator;
- data->phy = devm_usb_get_phy_by_phandle(&pdev->dev, "fsl,usbphy", 0);
+ data->phy = devm_usb_get_phy_by_phandle(dev, "fsl,usbphy", 0);
if (IS_ERR(data->phy)) {
ret = PTR_ERR(data->phy);
/* Return -EINVAL if no usbphy is available */
@@ -305,40 +393,43 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev)
ret = imx_usbmisc_init(data->usbmisc_data);
if (ret) {
- dev_err(&pdev->dev, "usbmisc init failed, ret=%d\n", ret);
+ dev_err(dev, "usbmisc init failed, ret=%d\n", ret);
goto err_clk;
}
- data->ci_pdev = ci_hdrc_add_device(&pdev->dev,
+ data->ci_pdev = ci_hdrc_add_device(dev,
pdev->resource, pdev->num_resources,
&pdata);
if (IS_ERR(data->ci_pdev)) {
ret = PTR_ERR(data->ci_pdev);
if (ret != -EPROBE_DEFER)
- dev_err(&pdev->dev,
- "ci_hdrc_add_device failed, err=%d\n", ret);
+ dev_err(dev, "ci_hdrc_add_device failed, err=%d\n",
+ ret);
goto err_clk;
}
ret = imx_usbmisc_init_post(data->usbmisc_data);
if (ret) {
- dev_err(&pdev->dev, "usbmisc post failed, ret=%d\n", ret);
+ dev_err(dev, "usbmisc post failed, ret=%d\n", ret);
goto disable_device;
}
if (data->supports_runtime_pm) {
- pm_runtime_set_active(&pdev->dev);
- pm_runtime_enable(&pdev->dev);
+ pm_runtime_set_active(dev);
+ pm_runtime_enable(dev);
}
- device_set_wakeup_capable(&pdev->dev, true);
+ device_set_wakeup_capable(dev, true);
return 0;
disable_device:
ci_hdrc_remove_device(data->ci_pdev);
err_clk:
- imx_disable_unprepare_clks(&pdev->dev);
+ imx_disable_unprepare_clks(dev);
+disable_hsic_regulator:
+ if (data->hsic_pad_regulator)
+ ret = regulator_disable(data->hsic_pad_regulator);
return ret;
}
@@ -355,6 +446,8 @@ static int ci_hdrc_imx_remove(struct platform_device *pdev)
if (data->override_phy_control)
usb_phy_shutdown(data->phy);
imx_disable_unprepare_clks(&pdev->dev);
+ if (data->hsic_pad_regulator)
+ regulator_disable(data->hsic_pad_regulator);
return 0;
}
@@ -367,9 +460,16 @@ static void ci_hdrc_imx_shutdown(struct platform_device *pdev)
static int __maybe_unused imx_controller_suspend(struct device *dev)
{
struct ci_hdrc_imx_data *data = dev_get_drvdata(dev);
+ int ret = 0;
dev_dbg(dev, "at %s\n", __func__);
+ ret = imx_usbmisc_hsic_set_clk(data->usbmisc_data, false);
+ if (ret) {
+ dev_err(dev, "usbmisc hsic_set_clk failed, ret=%d\n", ret);
+ return ret;
+ }
+
imx_disable_unprepare_clks(dev);
data->in_lpm = true;
@@ -400,8 +500,16 @@ static int __maybe_unused imx_controller_resume(struct device *dev)
goto clk_disable;
}
+ ret = imx_usbmisc_hsic_set_clk(data->usbmisc_data, true);
+ if (ret) {
+ dev_err(dev, "usbmisc hsic_set_clk failed, ret=%d\n", ret);
+ goto hsic_set_clk_fail;
+ }
+
return 0;
+hsic_set_clk_fail:
+ imx_usbmisc_set_wakeup(data->usbmisc_data, true);
clk_disable:
imx_disable_unprepare_clks(dev);
return ret;
diff --git a/drivers/usb/chipidea/ci_hdrc_imx.h b/drivers/usb/chipidea/ci_hdrc_imx.h
index 204275f47573..fcecab478934 100644
--- a/drivers/usb/chipidea/ci_hdrc_imx.h
+++ b/drivers/usb/chipidea/ci_hdrc_imx.h
@@ -14,10 +14,13 @@ struct imx_usbmisc_data {
unsigned int oc_polarity:1; /* over current polarity if oc enabled */
unsigned int evdo:1; /* set external vbus divider option */
unsigned int ulpi:1; /* connected to an ULPI phy */
+ unsigned int hsic:1; /* HSIC controlller */
};
-int imx_usbmisc_init(struct imx_usbmisc_data *);
-int imx_usbmisc_init_post(struct imx_usbmisc_data *);
-int imx_usbmisc_set_wakeup(struct imx_usbmisc_data *, bool);
+int imx_usbmisc_init(struct imx_usbmisc_data *data);
+int imx_usbmisc_init_post(struct imx_usbmisc_data *data);
+int imx_usbmisc_set_wakeup(struct imx_usbmisc_data *data, bool enabled);
+int imx_usbmisc_hsic_set_connect(struct imx_usbmisc_data *data);
+int imx_usbmisc_hsic_set_clk(struct imx_usbmisc_data *data, bool on);
#endif /* __DRIVER_USB_CHIPIDEA_CI_HDRC_IMX_H */
diff --git a/drivers/usb/chipidea/usbmisc_imx.c b/drivers/usb/chipidea/usbmisc_imx.c
index def80ff547e4..43a15a6e86f5 100644
--- a/drivers/usb/chipidea/usbmisc_imx.c
+++ b/drivers/usb/chipidea/usbmisc_imx.c
@@ -64,10 +64,22 @@
#define MX6_BM_OVER_CUR_DIS BIT(7)
#define MX6_BM_OVER_CUR_POLARITY BIT(8)
#define MX6_BM_WAKEUP_ENABLE BIT(10)
+#define MX6_BM_UTMI_ON_CLOCK BIT(13)
#define MX6_BM_ID_WAKEUP BIT(16)
#define MX6_BM_VBUS_WAKEUP BIT(17)
#define MX6SX_BM_DPDM_WAKEUP_EN BIT(29)
#define MX6_BM_WAKEUP_INTR BIT(31)
+
+#define MX6_USB_HSIC_CTRL_OFFSET 0x10
+/* Send resume signal without 480Mhz PHY clock */
+#define MX6SX_BM_HSIC_AUTO_RESUME BIT(23)
+/* set before portsc.suspendM = 1 */
+#define MX6_BM_HSIC_DEV_CONN BIT(21)
+/* HSIC enable */
+#define MX6_BM_HSIC_EN BIT(12)
+/* Force HSIC module 480M clock on, even when in Host is in suspend mode */
+#define MX6_BM_HSIC_CLK_ON BIT(11)
+
#define MX6_USB_OTG1_PHY_CTRL 0x18
/* For imx6dql, it is host-only controller, for later imx6, it is otg's */
#define MX6_USB_OTG2_PHY_CTRL 0x1c
@@ -94,6 +106,10 @@ struct usbmisc_ops {
int (*post)(struct imx_usbmisc_data *data);
/* It's called when we need to enable/disable usb wakeup */
int (*set_wakeup)(struct imx_usbmisc_data *data, bool enabled);
+ /* It's called before setting portsc.suspendM */
+ int (*hsic_set_connect)(struct imx_usbmisc_data *data);
+ /* It's called during suspend/resume */
+ int (*hsic_set_clk)(struct imx_usbmisc_data *data, bool enabled);
};
struct imx_usbmisc {
@@ -353,6 +369,18 @@ static int usbmisc_imx6q_init(struct imx_usbmisc_data *data)
writel(reg | MX6_BM_NON_BURST_SETTING,
usbmisc->base + data->index * 4);
+ /* For HSIC controller */
+ if (data->hsic) {
+ reg = readl(usbmisc->base + data->index * 4);
+ writel(reg | MX6_BM_UTMI_ON_CLOCK,
+ usbmisc->base + data->index * 4);
+ reg = readl(usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET
+ + (data->index - 2) * 4);
+ reg |= MX6_BM_HSIC_EN | MX6_BM_HSIC_CLK_ON;
+ writel(reg, usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET
+ + (data->index - 2) * 4);
+ }
+
spin_unlock_irqrestore(&usbmisc->lock, flags);
usbmisc_imx6q_set_wakeup(data, false);
@@ -360,6 +388,79 @@ static int usbmisc_imx6q_init(struct imx_usbmisc_data *data)
return 0;
}
+static int usbmisc_imx6_hsic_get_reg_offset(struct imx_usbmisc_data *data)
+{
+ int offset, ret = 0;
+
+ if (data->index == 2 || data->index == 3) {
+ offset = (data->index - 2) * 4;
+ } else if (data->index == 0) {
+ /*
+ * For SoCs like i.MX7D and later, each USB controller has
+ * its own non-core register region. For SoCs before i.MX7D,
+ * the first two USB controllers are non-HSIC controllers.
+ */
+ offset = 0;
+ } else {
+ dev_err(data->dev, "index is error for usbmisc\n");
+ ret = -EINVAL;
+ }
+
+ return ret ? ret : offset;
+}
+
+static int usbmisc_imx6_hsic_set_connect(struct imx_usbmisc_data *data)
+{
+ unsigned long flags;
+ u32 val;
+ struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
+ int offset;
+
+ spin_lock_irqsave(&usbmisc->lock, flags);
+ offset = usbmisc_imx6_hsic_get_reg_offset(data);
+ if (offset < 0) {
+ spin_unlock_irqrestore(&usbmisc->lock, flags);
+ return offset;
+ }
+
+ val = readl(usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET + offset);
+ if (!(val & MX6_BM_HSIC_DEV_CONN))
+ writel(val | MX6_BM_HSIC_DEV_CONN,
+ usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET + offset);
+
+ spin_unlock_irqrestore(&usbmisc->lock, flags);
+
+ return 0;
+}
+
+static int usbmisc_imx6_hsic_set_clk(struct imx_usbmisc_data *data, bool on)
+{
+ unsigned long flags;
+ u32 val;
+ struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
+ int offset;
+
+ spin_lock_irqsave(&usbmisc->lock, flags);
+ offset = usbmisc_imx6_hsic_get_reg_offset(data);
+ if (offset < 0) {
+ spin_unlock_irqrestore(&usbmisc->lock, flags);
+ return offset;
+ }
+
+ val = readl(usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET + offset);
+ val |= MX6_BM_HSIC_EN | MX6_BM_HSIC_CLK_ON;
+ if (on)
+ val |= MX6_BM_HSIC_CLK_ON;
+ else
+ val &= ~MX6_BM_HSIC_CLK_ON;
+
+ writel(val, usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET + offset);
+ spin_unlock_irqrestore(&usbmisc->lock, flags);
+
+ return 0;
+}
+
+
static int usbmisc_imx6sx_init(struct imx_usbmisc_data *data)
{
void __iomem *reg = NULL;
@@ -385,6 +486,13 @@ static int usbmisc_imx6sx_init(struct imx_usbmisc_data *data)
spin_unlock_irqrestore(&usbmisc->lock, flags);
}
+ /* For HSIC controller */
+ if (data->hsic) {
+ val = readl(usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET);
+ val |= MX6SX_BM_HSIC_AUTO_RESUME;
+ writel(val, usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET);
+ }
+
return 0;
}
@@ -454,6 +562,7 @@ static int usbmisc_imx7d_init(struct imx_usbmisc_data *data)
reg &= ~MX7D_USB_VBUS_WAKEUP_SOURCE_MASK;
writel(reg | MX7D_USB_VBUS_WAKEUP_SOURCE_BVALID,
usbmisc->base + MX7D_USBNC_USB_CTRL2);
+
spin_unlock_irqrestore(&usbmisc->lock, flags);
usbmisc_imx7d_set_wakeup(data, false);
@@ -481,6 +590,8 @@ static const struct usbmisc_ops imx53_usbmisc_ops = {
static const struct usbmisc_ops imx6q_usbmisc_ops = {
.set_wakeup = usbmisc_imx6q_set_wakeup,
.init = usbmisc_imx6q_init,
+ .hsic_set_connect = usbmisc_imx6_hsic_set_connect,
+ .hsic_set_clk = usbmisc_imx6_hsic_set_clk,
};
static const struct usbmisc_ops vf610_usbmisc_ops = {
@@ -490,6 +601,8 @@ static const struct usbmisc_ops vf610_usbmisc_ops = {
static const struct usbmisc_ops imx6sx_usbmisc_ops = {
.set_wakeup = usbmisc_imx6q_set_wakeup,
.init = usbmisc_imx6sx_init,
+ .hsic_set_connect = usbmisc_imx6_hsic_set_connect,
+ .hsic_set_clk = usbmisc_imx6_hsic_set_clk,
};
static const struct usbmisc_ops imx7d_usbmisc_ops = {
@@ -546,6 +659,33 @@ int imx_usbmisc_set_wakeup(struct imx_usbmisc_data *data, bool enabled)
}
EXPORT_SYMBOL_GPL(imx_usbmisc_set_wakeup);
+int imx_usbmisc_hsic_set_connect(struct imx_usbmisc_data *data)
+{
+ struct imx_usbmisc *usbmisc;
+
+ if (!data)
+ return 0;
+
+ usbmisc = dev_get_drvdata(data->dev);
+ if (!usbmisc->ops->hsic_set_connect || !data->hsic)
+ return 0;
+ return usbmisc->ops->hsic_set_connect(data);
+}
+EXPORT_SYMBOL_GPL(imx_usbmisc_hsic_set_connect);
+
+int imx_usbmisc_hsic_set_clk(struct imx_usbmisc_data *data, bool on)
+{
+ struct imx_usbmisc *usbmisc;
+
+ if (!data)
+ return 0;
+
+ usbmisc = dev_get_drvdata(data->dev);
+ if (!usbmisc->ops->hsic_set_clk || !data->hsic)
+ return 0;
+ return usbmisc->ops->hsic_set_clk(data, on);
+}
+EXPORT_SYMBOL_GPL(imx_usbmisc_hsic_set_clk);
static const struct of_device_id usbmisc_imx_dt_ids[] = {
{
.compatible = "fsl,imx25-usbmisc",
--
2.14.1
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH v4 3/4] usb: chipidea: host: override ehci->hub_control
2018-12-09 5:40 [PATCH v4 0/4] usb: chipidea: imx: add HSIC support Peter Chen
2018-12-09 5:40 ` [PATCH v4 1/4] usb: chipidea: add flag for imx hsic implementation Peter Chen
2018-12-09 5:40 ` [PATCH v4 2/4] usb: chipidea: imx: add HSIC support Peter Chen
@ 2018-12-09 5:40 ` Peter Chen
2018-12-09 5:40 ` [PATCH v4 4/4] doc: usb: ci-hdrc-usb2: Add pinctrl properties for HSIC pin groups Peter Chen
3 siblings, 0 replies; 8+ messages in thread
From: Peter Chen @ 2018-12-09 5:40 UTC (permalink / raw)
To: linux-usb@vger.kernel.org
Cc: dl-linux-imx, robh+dt@kernel.org, devicetree@vger.kernel.org,
frieder.schrempf@exceet.de, festevam@gmail.com, Peter Chen
The chipidea controller has some special requirements during
suspend/resume, override common ehci->hub_control to implement
it.
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
---
drivers/usb/chipidea/host.c | 75 +++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 75 insertions(+)
diff --git a/drivers/usb/chipidea/host.c b/drivers/usb/chipidea/host.c
index 028a3574266a..b45ceb91c735 100644
--- a/drivers/usb/chipidea/host.c
+++ b/drivers/usb/chipidea/host.c
@@ -220,6 +220,80 @@ void ci_hdrc_host_destroy(struct ci_hdrc *ci)
host_stop(ci);
}
+/* The below code is based on tegra ehci driver */
+static int ci_ehci_hub_control(
+ struct usb_hcd *hcd,
+ u16 typeReq,
+ u16 wValue,
+ u16 wIndex,
+ char *buf,
+ u16 wLength
+)
+{
+ struct ehci_hcd *ehci = hcd_to_ehci(hcd);
+ u32 __iomem *status_reg;
+ u32 temp;
+ unsigned long flags;
+ int retval = 0;
+ struct device *dev = hcd->self.controller;
+ struct ci_hdrc *ci = dev_get_drvdata(dev);
+
+ status_reg = &ehci->regs->port_status[(wIndex & 0xff) - 1];
+
+ spin_lock_irqsave(&ehci->lock, flags);
+
+ if (typeReq == SetPortFeature && wValue == USB_PORT_FEAT_SUSPEND) {
+ temp = ehci_readl(ehci, status_reg);
+ if ((temp & PORT_PE) == 0 || (temp & PORT_RESET) != 0) {
+ retval = -EPIPE;
+ goto done;
+ }
+
+ temp &= ~(PORT_RWC_BITS | PORT_WKCONN_E);
+ temp |= PORT_WKDISC_E | PORT_WKOC_E;
+ ehci_writel(ehci, temp | PORT_SUSPEND, status_reg);
+
+ /*
+ * If a transaction is in progress, there may be a delay in
+ * suspending the port. Poll until the port is suspended.
+ */
+ if (ehci_handshake(ehci, status_reg, PORT_SUSPEND,
+ PORT_SUSPEND, 5000))
+ ehci_err(ehci, "timeout waiting for SUSPEND\n");
+
+ if (ci->platdata->flags & CI_HDRC_IMX_IS_HSIC) {
+ if (ci->platdata->notify_event)
+ ci->platdata->notify_event(ci,
+ CI_HDRC_IMX_HSIC_SUSPEND_EVENT);
+
+ temp = ehci_readl(ehci, status_reg);
+ temp &= ~(PORT_WKDISC_E | PORT_WKCONN_E);
+ ehci_writel(ehci, temp, status_reg);
+ }
+
+ set_bit((wIndex & 0xff) - 1, &ehci->suspended_ports);
+ goto done;
+ }
+
+ /*
+ * After resume has finished, it needs do some post resume
+ * operation for some SoCs.
+ */
+ else if (typeReq == ClearPortFeature &&
+ wValue == USB_PORT_FEAT_C_SUSPEND) {
+ /* Make sure the resume has finished, it should be finished */
+ if (ehci_handshake(ehci, status_reg, PORT_RESUME, 0, 25000))
+ ehci_err(ehci, "timeout waiting for resume\n");
+ }
+
+ spin_unlock_irqrestore(&ehci->lock, flags);
+
+ /* Handle the hub control events here */
+ return ehci_hub_control(hcd, typeReq, wValue, wIndex, buf, wLength);
+done:
+ spin_unlock_irqrestore(&ehci->lock, flags);
+ return retval;
+}
static int ci_ehci_bus_suspend(struct usb_hcd *hcd)
{
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
@@ -298,4 +372,5 @@ void ci_hdrc_host_driver_init(void)
ehci_init_driver(&ci_ehci_hc_driver, &ehci_ci_overrides);
orig_bus_suspend = ci_ehci_hc_driver.bus_suspend;
ci_ehci_hc_driver.bus_suspend = ci_ehci_bus_suspend;
+ ci_ehci_hc_driver.hub_control = ci_ehci_hub_control;
}
--
2.14.1
^ permalink raw reply related [flat|nested] 8+ messages in thread