Re: [PATCH v2 2/9] dt/bindings: drm/komeda: Add DT bindings for ARM display processor D71

["james qian wang (Arm Technology China)" <james.qian.wang@arm.com>]

On Wed, Dec 19, 2018 at 07:55:44AM -0600, Rob Herring wrote:
> On Wed, Dec 19, 2018 at 6:33 AM james qian wang (Arm Technology China)
> <james.qian.wang@arm.com> wrote:
> >
> > Add DT bindings documentation for the ARM display processor D71 and later
> > IPs.
> >
> > Signed-off-by: James (Qian) Wang <james.qian.wang@arm.com>
> > ---
> >  .../bindings/display/arm/arm,komeda.txt       | 87 +++++++++++++++++++
> >  1 file changed, 87 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/display/arm/arm,komeda.txt
> >
> > diff --git a/Documentation/devicetree/bindings/display/arm/arm,komeda.txt b/Documentation/devicetree/bindings/display/arm/arm,komeda.txt
> > new file mode 100644
> > index 000000000000..d4b53c11b2a2
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/display/arm/arm,komeda.txt
> > @@ -0,0 +1,87 @@
> > +Device Tree bindings for ARM Komeda display driver
> > +
> > +Required properties:
> > +- compatible: Should be "arm,mali-d71"
> > +- reg: Physical base address and length of the registers in the system
> > +- interrupts: the interrupt line numbers of the device in the system
> 
> How many?

Sorry, only one interrupt. will fix it in the next version. 

> > +- interrupt-names: contains the names of the IRQs in the order they were
> > +    provided in the "interrupts" property. Must contain: "DPU".
> 
> There's no point in *-names when there is only one entry.
> 
> > +- clocks: A list of phandle + clock-specifier pairs, one for each entry
> > +    in 'clock-names'
> > +- clock-names: A list of clock names. It should contain:
> > +      - "pclk": for the APB interface clock
> > +      - "mclk": for the main processor clock
> 
> The order here doesn't match the example.

will fix it.

> 
> > +- #address-cells: Must be 1
> > +- #size-cells: Must be 0
> > +
> > +Required properties for sub-node: pipeline@nq
> > +Each device contains one or two pipeline sub-nodes (at least one), each
> > +pipeline node should provide properties:
> > +- reg: Zero-indexed identifier for the pipeline
> > +- clocks: A list of phandle + clock-specifier pairs, one for each entry
> > +    in 'clock-names'
> > +- clock-names: should contain:
> > +      - "aclk": AXI interface clock
> > +      - "pxclk": pixel clock
> 
> The order here doesn't match the example.
>

will fix it in the next version.

> > +
> > +- port: each pipeline connect to an encoder input port. The connection is
> > +    modelled using the OF graph bindings specified in
> 
> modeled

will fix it.

> 
> > +    Documentation/devicetree/bindings/graph.txt
> > +
> > +Optional properties:
> > +  - memory-region: phandle to a node describing memory (see
> > +    Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt)
> > +    to be used for the framebuffer; if not present, the framebuffer may
> > +    be located anywhere in memory.
> > +
> > +Example:
> > +/ {
> > +       ...
> > +
> > +       dp0: display@c00000 {
> > +               #address-cells = <1>;
> > +               #size-cells = <0>;
> > +               compatible = "arm,mali-d71";
> > +               reg = <0xc00000 0x20000>;
> > +               interrupts = <0 168 4>;
> > +               interrupt-names = "DPU";
> > +               clocks = <&dpu_mclk>, <&dpu_aclk>;
> > +               clock-names = "mclk", "pclk";
> > +
> > +               pl0: pipeline@0 {
> > +                       clocks = <&fpgaosc2>, <&dpu_aclk>;
> > +                       clock-names = "pxclk", "aclk";
> > +                       reg = <0>;
> 
> Is there a register range for each pipeline? If so, using that here
> would be better than index.

Sorry, there is no register range for the pipeline.

> 
> > +
> > +                       ports {
> > +                               #address-cells = <1>;
> > +                               #size-cells = <0>;
> > +
> > +                               port@0 {
> > +                                       reg = <0>;
> 
> You can drop 'ports' moving port up a level. And for a single port,
> you don't need reg.

you're right will fix it.
> 
> > +                                       dp0_pl0_out: endpoint {
> > +                                               remote-endpoint = <&db_dvi0_in>;
> > +                                       };
> > +                               };
> > +                       };
> > +               };
> > +               pl1: pipeline@1 {
> > +                       clocks = <&fpgaosc2>, <&dpu_aclk>;
> > +                       clock-names = "pxclk", "aclk";
> > +                       reg = <1>;
> > +
> > +                       ports {
> > +                               #address-cells = <1>;
> > +                               #size-cells = <0>;
> > +
> > +                               port@0 {
> > +                                       reg = <0>;
> > +                                       dp0_pl1_out: endpoint {
> > +                                               remote-endpoint = <&db_dvi1_in>;
> > +                                       };
> > +                               };
> > +                       };
> > +               };
> > +       };
> > +       ...
> > +};
> > --
> > 2.17.1
> >
> > _______________________________________________
> > dri-devel mailing list
> > dri-devel@lists.freedesktop.org
> > https://lists.freedesktop.org/mailman/listinfo/dri-devel
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel