[PATCH AUTOSEL 4.14 023/170] MIPS: Boston: Disable EG20T prefetch

[PATCH AUTOSEL 4.14 023/170] MIPS: Boston: Disable EG20T prefetch

[Sasha Levin]

From: Paul Burton <paul.burton@mips.com>

[ Upstream commit 5ec17af7ead09701e23d2065e16db6ce4e137289 ]

The Intel EG20T Platform Controller Hub used on the MIPS Boston
development board supports prefetching memory to optimize DMA transfers.
Unfortunately for unknown reasons this doesn't work well with some MIPS
CPUs such as the P6600, particularly when using an I/O Coherence Unit
(IOCU) to provide cache-coherent DMA. In these systems it is common for
DMA data to be lost, resulting in broken access to EG20T devices such as
the MMC or SATA controllers.

Support for a DT property to configure the prefetching was added a while
back by commit 549ce8f134bd ("misc: pch_phub: Read prefetch value from
device tree if passed") but we never added the DT snippet to make use of
it. Add that now in order to disable the prefetching & fix DMA on the
affected systems.

Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21068/
Cc: linux-mips@linux-mips.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/mips/boot/dts/img/boston.dts | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/mips/boot/dts/img/boston.dts b/arch/mips/boot/dts/img/boston.dts
index f7aad80c69ab..bebb0fa21369 100644
--- a/arch/mips/boot/dts/img/boston.dts
+++ b/arch/mips/boot/dts/img/boston.dts
@@ -141,6 +141,12 @@
 				#size-cells = <2>;
 				#interrupt-cells = <1>;
 
+				eg20t_phub@2,0,0 {
+					compatible = "pci8086,8801";
+					reg = <0x00020000 0 0 0 0>;
+					intel,eg20t-prefetch = <0>;
+				};
+
 				eg20t_mac@2,0,1 {
 					compatible = "pci8086,8802";
 					reg = <0x00020100 0 0 0 0>;
-- 
2.19.1

[PATCH AUTOSEL 4.14 060/170] ARM: dts: mmp2: fix TWSI2

[Sasha Levin]

From: Lubomir Rintel <lkundrak@v3.sk>

[ Upstream commit 1147e05ac9fc2ef86a3691e7ca5c2db7602d81dd ]

Marvell keeps their MMP2 datasheet secret, but there are good clues
that TWSI2 is not on 0xd4025000 on that platform, not does it use
IRQ 58. In fact, the IRQ 58 on MMP2 seems to be a signal processor:

   arch/arm/mach-mmp/irqs.h:#define IRQ_MMP2_MSP  58

I'm taking a somewhat educated guess that is probably a copy & paste
error from PXA168 or PXA910 and that the real controller in fact hides
at address 0xd4031000 and uses an interrupt line multiplexed via IRQ 17.

I'm also copying some properties from TWSI1 that were missing or
incorrect.

Tested on a OLPC XO 1.75 machine, where the RTC is on TWSI2.

Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/mmp2.dtsi | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/mmp2.dtsi b/arch/arm/boot/dts/mmp2.dtsi
index 766bbb8495b6..47e5b63339d1 100644
--- a/arch/arm/boot/dts/mmp2.dtsi
+++ b/arch/arm/boot/dts/mmp2.dtsi
@@ -220,12 +220,15 @@
 				status = "disabled";
 			};
 
-			twsi2: i2c@d4025000 {
+			twsi2: i2c@d4031000 {
 				compatible = "mrvl,mmp-twsi";
-				reg = <0xd4025000 0x1000>;
-				interrupts = <58>;
+				reg = <0xd4031000 0x1000>;
+				interrupt-parent = <&intcmux17>;
+				interrupts = <0>;
 				clocks = <&soc_clocks MMP2_CLK_TWSI1>;
 				resets = <&soc_clocks MMP2_CLK_TWSI1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 				status = "disabled";
 			};
 
-- 
2.19.1

[PATCH AUTOSEL 4.14 076/170] ARM: dts: Fix OMAP4430 SDP Ethernet startup

[Sasha Levin]

From: Russell King - ARM Linux <linux@armlinux.org.uk>

[ Upstream commit 84fb6c7feb1494ebb7d1ec8b95cfb7ada0264465 ]

It was noticed that unbinding and rebinding the KSZ8851 ethernet
resulted in the driver reporting "failed to read device ID" at probe.
Probing the reset line with a 'scope while repeatedly attempting to
bind the driver in a shell loop revealed that the KSZ8851 RSTN pin is
constantly held at zero, meaning the device is held in reset, and
does not respond on the SPI bus.

Experimentation with the startup delay on the regulator set to 50ms
shows that the reset is positively released after 20ms.

Schematics for this board are not available, and the traces are buried
in the inner layers of the board which makes tracing where the RSTN pin
extremely difficult.  We can only guess that the RSTN pin is wired to a
reset generator chip driven off the ethernet supply, which fits the
observed behaviour.

Include this delay in the regulator startup delay - effectively
treating the reset as a "supply stable" indicator.

This can not be modelled as a delay in the KSZ8851 driver since the
reset generation is board specific - if the RSTN pin had been wired to
a GPIO, reset could be released earlier via the already provided support
in the KSZ8851 driver.

This also got confirmed by Peter Ujfalusi <peter.ujfalusi@ti.com> based
on Blaze schematics that should be very close to SDP4430:

TPS22902YFPR is used as the regulator switch (gpio48 controlled):
Convert arm boot_lock to raw The VOUT is routed to TPS3808G01DBV.
(SCH Note: Threshold set at 90%. Vsense: 0.405V).

According to the TPS3808 data sheet the RESET delay time when Ct is
open (this is the case in the schema): MIN/TYP/MAX: 12/20/28 ms.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated with notes from schematics from Peter]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/omap4-sdp.dts | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts
index 280d92d42bf1..bfad6aadfe88 100644
--- a/arch/arm/boot/dts/omap4-sdp.dts
+++ b/arch/arm/boot/dts/omap4-sdp.dts
@@ -33,6 +33,7 @@
 		gpio = <&gpio2 16 GPIO_ACTIVE_HIGH>;  /* gpio line 48 */
 		enable-active-high;
 		regulator-boot-on;
+		startup-delay-us = <25000>;
 	};
 
 	vbat: fixedregulator-vbat {
-- 
2.19.1

[PATCH AUTOSEL 4.14 079/170] ARM: dts: Fix up the D-Link DIR-685 MTD partition info

[Sasha Levin]

From: Linus Walleij <linus.walleij@linaro.org>

[ Upstream commit 738a05e673435afb986b53da43befd83ad87ec3b ]

The vendor firmware was analyzed to get the right idea about
this flash layout. /proc/mtd contains:

dev:    size   erasesize  name
mtd0: 01e7ff40 00020000 "rootfs"
mtd1: 01f40000 00020000 "upgrade"
mtd2: 00040000 00020000 "rgdb"
mtd3: 00020000 00020000 "nvram"
mtd4: 00040000 00020000 "RedBoot"
mtd5: 00020000 00020000 "LangPack"
mtd6: 02000000 00020000 "flash"

Here "flash" is obviously the whole device and we know "rootfs"
is a bogus hack to point to a squashfs rootfs inside of the main
"upgrade partition". We know "RedBoot" is the first 0x40000 of
the flash and the "upgrade" partition follows from 0x40000 to
0x1f8000. So we have mtd0, 1, 4 and 6 covered.

Remains:
mtd2: 00040000 00020000 "rgdb"
mtd3: 00020000 00020000 "nvram"
mtd5: 00020000 00020000 "LangPack"

Inspecting the flash at 0x1f8000 and 0x1fa000 reveals each of
these starting with "RGCFG1" so we assume 0x1f8000-1fbfff is
"rgdb" of 0x40000.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/gemini-dlink-dir-685.dts | 16 ++++++----------
 1 file changed, 6 insertions(+), 10 deletions(-)

diff --git a/arch/arm/boot/dts/gemini-dlink-dir-685.dts b/arch/arm/boot/dts/gemini-dlink-dir-685.dts
index e75e2d44371c..d6f752ab07bb 100644
--- a/arch/arm/boot/dts/gemini-dlink-dir-685.dts
+++ b/arch/arm/boot/dts/gemini-dlink-dir-685.dts
@@ -128,20 +128,16 @@
 				read-only;
 			};
 			/*
-			 * Between the boot loader and the rootfs is the kernel
-			 * in a custom Storlink format flashed from the boot
-			 * menu. The rootfs is in squashfs format.
+			 * This firmware image contains the kernel catenated
+			 * with the squashfs root filesystem. For some reason
+			 * this is called "upgrade" on the vendor system.
 			 */
-			partition@1800c0 {
-				label = "rootfs";
-				reg = <0x001800c0 0x01dbff40>;
-				read-only;
-			};
-			partition@1f40000 {
+			partition@40000 {
 				label = "upgrade";
-				reg = <0x01f40000 0x00040000>;
+				reg = <0x00040000 0x01f40000>;
 				read-only;
 			};
+			/* RGDB, Residental Gateway Database? */
 			partition@1f80000 {
 				label = "rgdb";
 				reg = <0x01f80000 0x00040000>;
-- 
2.19.1