Re: [PATCH v2 2/2] drm/panel: Add driver for Samsung S6E63M0 panel

[Sam Ravnborg <sam@ravnborg.org>]

Hi Paweł

Looks good, thanks for addressing all the review feedback.

On Fri, Feb 01, 2019 at 06:28:52PM +0100, Paweł Chmiel wrote:
> This patch adds Samsung S6E63M0 AMOLED LCD panel driver, connected over
> spi. It's based on already removed, non dt s6e63m0 driver and
> panel-samsung-ld9040. It can be found for example in some of Samsung
> Aries based phones.
> 
> Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
If you consider (do not change unless you think it better) the
following nits than you can add my:

Reviewed-by: Sam Ravnborg <sam@ravnborg.org>

	Sam

> diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
> index 3f3537719beb..be05ed5218eb 100644
> --- a/drivers/gpu/drm/panel/Kconfig
> +++ b/drivers/gpu/drm/panel/Kconfig
> @@ -158,6 +158,13 @@ config DRM_PANEL_SAMSUNG_S6E63J0X03
>  	depends on BACKLIGHT_CLASS_DEVICE
>  	select VIDEOMODE_HELPERS
>  
> +config DRM_PANEL_SAMSUNG_S6E63M0
> +	tristate "Samsung S6E63M0 RGB/SPI panel"
> +	depends on OF
> +	depends on SPI
> +	depends on BACKLIGHT_CLASS_DEVICE
> +	select VIDEOMODE_HELPERS
With the use of display_mode the above "select VIDEOMODE_HELPERS"
is likely no longer required. Please check.

A help text would be nice.

> +
>  config DRM_PANEL_SAMSUNG_S6E8AA0
>  	tristate "Samsung S6E8AA0 DSI video mode panel"
>  	depends on OF


> +#include <video/of_videomode.h>
> +#include <video/videomode.h>
Please check if these two files are required.

> +struct s6e63m0 {
> +	struct device *dev;
> +	struct drm_panel panel;
> +	struct backlight_device *bl_dev;
> +
> +	struct regulator_bulk_data supplies[2];
> +	struct gpio_desc *reset_gpio;
> +	struct videomode vm;
vm is no longer used - delete it.

> +
> +	bool prepared;
> +	bool enabled;
> +
> +	/*
> +	 * This field is tested by functions directly accessing bus before
> +	 * transfer, transfer is skipped if it is set. In case of transfer
> +	 * failure or unexpected response the field is set to error value.
> +	 * Such construct allows to eliminate many checks in higher level
> +	 * functions.
> +	 */
> +	int error;
> +};
> +

> +static int s6e63m0_get_modes(struct drm_panel *panel)
> +{
> +	struct drm_connector *connector = panel->connector;
> +	struct drm_display_mode *mode;
> +
> +	mode = drm_mode_duplicate(panel->drm, &default_mode);
> +	if (!mode) {
> +		DRM_ERROR("failed to add mode %ux%ux@%u\n",
> +			  default_mode.hdisplay, default_mode.vdisplay,
> +			  default_mode.vrefresh);
I recall I have seen a generic way to print the above,
but I have failed to find it.
Maybe it is just my memory that fools me.

The above is fine.

> +
> +	s6e63m0_backlight_register(ctx);

Is it correct that we continue even if we fail to register backlight?


> +
> +	return 0;
> +}
> +
> +
> +static const struct of_device_id s6e63m0_of_match[] = {
> +	{ .compatible = "samsung,s6e63m0" },
> +	{ }

Add /* sentinel */ comment?

> +};

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel