Re: [PATCH] ARM: sun8i: h3: bluetooth for Banana Pi M2 Zero board

[Andreas Kemnade <andreas@kemnade.info>]

[-- Attachment #1: Type: text/plain, Size: 2207 bytes --]

On Fri, 1 Mar 2019 15:36:32 +0100
Maxime Ripard <maxime.ripard@bootlin.com> wrote:

> Hi,
> 
> Thanks for your patch
> 
> On Thu, Feb 28, 2019 at 10:28:40PM +0100, Andreas Kemnade wrote:
> > The Banana Pi M2 Zero board has an AP6212 BT+Wifi combo chip
> > with broadcom internals attached to UART1 and some gpios.
> > This addition is in line with similar boards
> > 
> > Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
> > ---
> >  .../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts    | 29 ++++++++++++++++++++++
> >  1 file changed, 29 insertions(+)
> > 
> > diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> > index 1db2541135a7..39e206fac4e3 100644
> > --- a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> > +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> > @@ -69,6 +69,8 @@
> >  		compatible = "mmc-pwrseq-simple";
> >  		pinctrl-names = "default";
> >  		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
> > +		clocks = <&rtc 1>;
> > +		clock-names = "ext_clock";
> >  	};
> >  };
> >  
> > @@ -122,7 +124,34 @@
> >  &uart1 {
> >  	pinctrl-names = "default";
> >  	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
> > +	uart-has-rtscts;
> >  	status = "okay";
> > +
> > +	bluetooth {
> > +		compatible = "brcm,bcm43438-bt";
> > +		pinctrl-names = "default";
> > +		pinctrl-0 = <&bt_pins_out>, <&bt_pins_in>;
> > +		clocks = <&rtc 1>;
> > +		clock-names = "lpo";
> > +		vbat-supply = <&reg_vcc3v3>;
> > +		vddio-supply = <&reg_vcc3v3>;
> > +		device-wakeup-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
> > +		host-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
> > +		shutdown-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
> > +	};
> > +
> > +};
> > +
> > +&pio {
> > +	bt_pins_out: bt_out {
> > +		pins = "PG12", "PG13";
> > +		function = "gpio_out";
> > +	};
> > +
> > +	bt_pins_in: bt_in {
> > +		pins = "PG11";
> > +		function = "gpio_in";
> > +	};  
> 
> You don't need any of those pinctrl nodes, GPIOs work fine without.
> 
ok, that makes things easier. I will resend a v2 without them.

Regards,
Andreas

[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 833 bytes --]