From: "Angus Ainslie (Purism)" <angus@akkea.ca>
To: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>, Shawn Guo <shawnguo@kernel.org>,
Fabio Estevam <festevam@gmail.com>,
kernel@pengutronix.de, Lucas Stach <l.stach@pengutronix.de>,
abel.vesa@nxp.com, daniel.baluta@nxp.com, agx@sigxcpu.org,
linux-imx@nxp.com, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
"Angus Ainslie (Purism)" <angus@akkea.ca>
Subject: [PATCH] arm64: dts: fsl: imx8mq: enable the thermal management unit (TMU)
Date: Mon, 11 Mar 2019 14:31:24 -0700 [thread overview]
Message-ID: <20190311213124.29325-1-angus@akkea.ca> (raw)
These are the TMU nodes from the NXP vendor kernel
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
---
arch/arm64/boot/dts/freescale/imx8mq.dtsi | 83 +++++++++++++++++++++++
1 file changed, 83 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
index 9155bd4784eb..087620c6e17f 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
@@ -8,6 +8,7 @@
#include <dt-bindings/power/imx8mq-power.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/thermal/thermal.h>
#include "imx8mq-pinfunc.h"
/ {
@@ -89,6 +90,7 @@
reg = <0x0>;
enable-method = "psci";
next-level-cache = <&A53_L2>;
+ #cooling-cells = <2>;
};
A53_1: cpu@1 {
@@ -210,6 +212,87 @@
#interrupt-cells = <2>;
};
+ tmu: tmu@30260000 {
+ compatible = "fsl,imx8mq-tmu";
+ reg = <0x30260000 0x10000>;
+ interrupt = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+ little-endian;
+ fsl,tmu-range = <0xb0000 0xa0026 0x80048 0x70061>;
+ fsl,tmu-calibration = <0x00000000 0x00000023
+ 0x00000001 0x00000029
+ 0x00000002 0x0000002f
+ 0x00000003 0x00000035
+ 0x00000004 0x0000003d
+ 0x00000005 0x00000043
+ 0x00000006 0x0000004b
+ 0x00000007 0x00000051
+ 0x00000008 0x00000057
+ 0x00000009 0x0000005f
+ 0x0000000a 0x00000067
+ 0x0000000b 0x0000006f
+
+ 0x00010000 0x0000001b
+ 0x00010001 0x00000023
+ 0x00010002 0x0000002b
+ 0x00010003 0x00000033
+ 0x00010004 0x0000003b
+ 0x00010005 0x00000043
+ 0x00010006 0x0000004b
+ 0x00010007 0x00000055
+ 0x00010008 0x0000005d
+ 0x00010009 0x00000067
+ 0x0001000a 0x00000070
+
+ 0x00020000 0x00000017
+ 0x00020001 0x00000023
+ 0x00020002 0x0000002d
+ 0x00020003 0x00000037
+ 0x00020004 0x00000041
+ 0x00020005 0x0000004b
+ 0x00020006 0x00000057
+ 0x00020007 0x00000063
+ 0x00020008 0x0000006f
+
+ 0x00030000 0x00000015
+ 0x00030001 0x00000021
+ 0x00030002 0x0000002d
+ 0x00030003 0x00000039
+ 0x00030004 0x00000045
+ 0x00030005 0x00000053
+ 0x00030006 0x0000005f
+ 0x00030007 0x00000071>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ thermal-zones {
+ cpu-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <2000>;
+ thermal-sensors = <&tmu>;
+
+ trips {
+ cpu_alert0: trip0 {
+ temperature = <85000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu_crit0: trip1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert0>;
+ cooling-device = <&A53_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+ };
+
wdog1: watchdog@30280000 {
compatible = "fsl,imx8mq-wdt", "fsl,imx21-wdt";
reg = <0x30280000 0x10000>;
--
2.17.1
next reply other threads:[~2019-03-11 21:31 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-03-11 21:31 Angus Ainslie (Purism) [this message]
2019-03-12 2:35 ` [PATCH] arm64: dts: fsl: imx8mq: enable the thermal management unit (TMU) Andrey Smirnov
2019-03-12 12:54 ` Angus Ainslie
2019-03-12 20:18 ` Angus Ainslie
2019-03-12 20:32 ` Fabio Estevam
2019-03-13 0:31 ` Andrey Smirnov
2019-03-18 15:48 ` [PATCH v2] " Angus Ainslie (Purism)
2019-03-18 16:04 ` [PATCH] arm64: dts: fsl: imx8mq: enable the multi sensor TMU Angus Ainslie (Purism)
2019-03-18 16:52 ` Fabio Estevam
2019-03-18 18:46 ` [PATCH v2] " Angus Ainslie (Purism)
2019-03-19 11:46 ` Lucas Stach
2019-03-19 15:10 ` [PATCH v3] " Angus Ainslie (Purism)
2019-03-19 16:18 ` Fabio Estevam
2019-03-21 12:52 ` [PATCH v4] " Angus Ainslie (Purism)
2019-03-21 14:48 ` Lucas Stach
2019-03-22 2:11 ` Shawn Guo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190311213124.29325-1-angus@akkea.ca \
--to=angus@akkea.ca \
--cc=abel.vesa@nxp.com \
--cc=agx@sigxcpu.org \
--cc=daniel.baluta@nxp.com \
--cc=devicetree@vger.kernel.org \
--cc=festevam@gmail.com \
--cc=kernel@pengutronix.de \
--cc=l.stach@pengutronix.de \
--cc=linux-imx@nxp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).