[PATCH AUTOSEL 4.9 01/29] ARM: dts: bcm283x: Fix hdmi hpd gpio pull

[PATCH AUTOSEL 4.9 01/29] ARM: dts: bcm283x: Fix hdmi hpd gpio pull

[Sasha Levin]

From: Helen Koike <helen.koike@collabora.com>

[ Upstream commit 544e784188f1dd7c797c70b213385e67d92005b6 ]

Raspberry pi board model B revison 2 have the hot plug detector gpio
active high (and not low as it was in the dts).

Signed-off-by: Helen Koike <helen.koike@collabora.com>
Fixes: 49ac67e0c39c ("ARM: bcm2835: Add VC4 to the device tree.")
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
index 84df85ea6296..7efde03daadd 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
@@ -26,5 +26,5 @@
 };
 
 &hdmi {
-	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
 };
-- 
2.19.1

[PATCH AUTOSEL 4.9 11/29] ARM: dts: pfla02: increase phy reset duration

[Sasha Levin]

From: Marco Felsch <m.felsch@pengutronix.de>

[ Upstream commit 032f85c9360fb1a08385c584c2c4ed114b33c260 ]

Increase the reset duration to ensure correct phy functionality. The
reset duration is taken from barebox commit 52fdd510de ("ARM: dts:
pfla02: use long enough reset for ethernet phy"):

  Use a longer reset time for ethernet phy Micrel KSZ9031RNX. Otherwise a
  small percentage of modules have 'transmission timeouts' errors like

  barebox@Phytec phyFLEX-i.MX6 Quad Carrier-Board:/ ifup eth0
  warning: No MAC address set. Using random address 7e:94:4d:02:f8:f3
  eth0: 1000Mbps full duplex link detected
  eth0: transmission timeout
  T eth0: transmission timeout
  T eth0: transmission timeout
  T eth0: transmission timeout
  T eth0: transmission timeout

Cc: Stefan Christ <s.christ@phytec.de>
Cc: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Fixes: 3180f956668e ("ARM: dts: Phytec imx6q pfla02 and pbab01 support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi
index e0280cac2484..fed72a5f3ffa 100644
--- a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi
@@ -90,6 +90,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
+	phy-reset-duration = <10>; /* in msecs */
 	phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
 	phy-supply = <&vdd_eth_io_reg>;
 	status = "disabled";
-- 
2.19.1