Re: [PATCH v6 02/13] dt-bindings: misc: Add bindings for HiSilicon usb hub and data role switch functionality on HiKey960

[Rob Herring <robh@kernel.org>]

On Sat, Apr 20, 2019 at 02:40:08PM +0800, Yu Chen wrote:
> This patch adds binding documentation to support usb hub and usb
> data role switch of Hisilicon HiKey960 Board.

Sorry I've been slow to really review this, but I needed to look at the 
schematics to see what exactly is going on here.

I think this needs some changes to better reflect the h/w and utilize 
existing bindings. It should really be designed ignoring the muxing to 
start with. Define the binding for the TypeC connector and then the host 
hub and make sure they can coexist. Then overlay what you need to switch 
between the 2 modes which AFAICT is just a single GPIO. 

> 
> Cc: Kishon Vijay Abraham I <kishon@ti.com>
> Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Mark Rutland <mark.rutland@arm.com>
> Cc: John Stultz <john.stultz@linaro.org>
> Cc: Binghui Wang <wangbinghui@hisilicon.com>
> Signed-off-by: Yu Chen <chenyu56@huawei.com>
> ---
> v1:
> * Fix some format errors as suggested by Sergei.
> * Modify gpio description to use gpiod API.
> v2:
> * Remove information about Hikey.
> * Fix gpio description.
> * Remove device_type of endpoint.
> v3:
> * Remove property typec-vbus-enable-val.
> * Add description of pinctrl-names.
> * Add example for "hisilicon,gpio-hubv1"
> * Add flag in gpiod properties.
> ---
> ---
>  .../bindings/misc/hisilicon-hikey-usb.txt          | 52 ++++++++++++++++++++++
>  1 file changed, 52 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/misc/hisilicon-hikey-usb.txt
> 
> diff --git a/Documentation/devicetree/bindings/misc/hisilicon-hikey-usb.txt b/Documentation/devicetree/bindings/misc/hisilicon-hikey-usb.txt
> new file mode 100644
> index 000000000000..422e844df719
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/misc/hisilicon-hikey-usb.txt
> @@ -0,0 +1,52 @@
> +Support usb hub and usb data role switch of Hisilicon HiKey960 Board.
> +
> +-----------------------------
> +
> +Required properties:
> +- compatible: "hisilicon,gpio-hubv1","hisilicon,hikey960-usb"
> +- typec-vbus-gpios: gpio to control the vbus of typeC port

This should be a gpio regulator and then connected to 'vbus-supply' in a 
usb-connector node (see .../bindings/connectors/usb-connector.txt). 

Then you also need the RT1711HWSC TypeC controller in DT. That is 
typically the parent device of the connector node. 

> +- otg-switch-gpios: gpio to switch DP & DM between the hub and typeC port

This probably belongs in USB controller node.

> +- hub-vdd33-en-gpios: gpio to enable the power of hub

This too should be a gpio regulator and then in a hub node. We have 2 
ways to represent hubs. Either as an I2C device or as a child of the 
host controller. The latter is preferred, but I'm not too sure how the 
OF graph connection linking the controller to the TypeC connector will 
work with the usb bus binding.

> +- pinctrl-names: pin configuration state name ("default")
> +- pinctrl-0: pinctrl config
> +
> +Example
> +-----
> +
> +	hisi_hikey_usb: hisi_hikey_usb {
> +		compatible = "hisilicon,hikey960-usb";
> +		typec-vbus-gpios = <&gpio25 2 GPIO_ACTIVE_HIGH>;
> +		otg-switch-gpios = <&gpio25 6 GPIO_ACTIVE_HIGH>;
> +		hub-vdd33-en-gpios = <&gpio5 6 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&usbhub5734_pmx_func>;
> +
> +		port {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			hikey_usb_ep: endpoint@0 {
> +				reg = <0>;
> +				remote-endpoint = <&dwc3_role_switch_notify>;
> +			};
> +		};
> +	};
> +
> +	hisi_hikey_usb: hisi_hikey_usb {

Perhaps doesn't matter with my above feedback, but I don't understand 
the point of this 2nd example.

> +		compatible = "hisilicon,gpio-hubv1";
> +		typec-vbus-gpios = <&gpio25 2 GPIO_ACTIVE_LOW>;
> +		otg-switch-gpios = <&gpio25 6 GPIO_ACTIVE_HIGH>;
> +		hub-vdd33-en-gpios = <&gpio5 6 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&usbhub5734_pmx_func>;
> +
> +		port {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			hikey_usb_ep: endpoint@0 {
> +				reg = <0>;
> +				remote-endpoint = <&dwc3_role_switch_notify>;
> +			};
> +		};
> +	};
> -- 
> 2.15.0-rc2
>