From: Marco Felsch <m.felsch@pengutronix.de>
To: robh+dt@kernel.org, shawnguo@kernel.org, linux-imx@nxp.com
Cc: Stefan.Nickl@kontron.com, Gilles.Buloz@kontron.com,
Michael.Brunner@kontron.com, thomas.schaefer@kontron.com,
frieder.schrempf@kontron.de, kernel@pengutronix.de,
devicetree@vger.kernel.org
Subject: [PATCH 00/17] Add Support for Kontron SMARC-sAMX6i
Date: Thu, 9 May 2019 17:58:17 +0200 [thread overview]
Message-ID: <20190509155834.22838-1-m.felsch@pengutronix.de> (raw)
Hi,
this series adds the Kontron SoM 'SMARC-sAMX6i' which is compatible to
the SMARC 1.1 standard [1]. Most of the muxing can be done within the
SoM dtsi since the standard defines a unique SoM hardware interface.
This series is based on Priit Laes initial commit [2] which adds the
initial support. I addressed the comments and changed the copyright
since there where a lot of fixes.
Testers are welcome :) since I used a custome baseboard which doesn't
use all of the interfaces.
[1] https://sget.org/standards/smarc
[2] https://lore.kernel.org/patchwork/patch/762261/
Marco Felsch (14):
dt-bindings: add Kontron vendor prefix
ARCH: arm: dts: imx6qdl-kontron-samx6i: add SMARC SDIO interface
ARCH: arm: dts: imx6qdl-kontron-samx6i: add SMARC LCD interface
ARCH: arm: dts: imx6qdl-kontron-samx6i: add SMARC Management pins
ARCH: arm: dts: imx6qdl-kontron-samx6i: add SMARC GPIO interface
ARCH: arm: dts: imx6qdl-kontron-samx6i: add SMARC HDMI interface
ARCH: arm: dts: imx6qdl-kontron-samx6i: add SMARC CSI Camera interface
ARCH: arm: dts: imx6qdl-kontron-samx6i: add SMARC I2S interface
ARCH: arm: dts: imx6qdl-kontron-samx6i: add SMARC SPI1 interface
ARCH: arm: dts: imx6qdl-kontron-samx6i: add SMARC Watchdog
ARCH: arm: dts: imx6qdl-kontron-samx6i: add SMARC module eeprom
ARCH: arm: dts: imx6qdl-kontron-samx6i: add power management support
ARCH: arm: dts: imx6q-kontron-samx6i: add Kontron SMARC Quad/Dual SoM
ARCH: arm: dts: imx6dl-kontron-samx6i: add Kontron SMARC
Dual-Lite/Solo SoM
Michael Grzeschik (2):
ARCH: arm: dts: imx6qdl-kontron-samx6i: add SMARC SPI0 interface
ARCH: arm: dts: imx6qdl-kontron-samx6i: add boot spi-nor
Priit Laes (1):
ARCH: arm: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron
SMARC-sAMX6i module
.../devicetree/bindings/vendor-prefixes.txt | 1 +
arch/arm/boot/dts/imx6dl-kontron-samx6i.dtsi | 12 +
arch/arm/boot/dts/imx6q-kontron-samx6i.dtsi | 36 +
arch/arm/boot/dts/imx6qdl-kontron-samx6i.dtsi | 812 ++++++++++++++++++
4 files changed, 861 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-kontron-samx6i.dtsi
create mode 100644 arch/arm/boot/dts/imx6q-kontron-samx6i.dtsi
create mode 100644 arch/arm/boot/dts/imx6qdl-kontron-samx6i.dtsi
--
2.20.1
next reply other threads:[~2019-05-09 15:58 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-05-09 15:58 Marco Felsch [this message]
2019-05-09 15:58 ` [PATCH 01/17] dt-bindings: add Kontron vendor prefix Marco Felsch
2019-05-17 2:31 ` Rob Herring
2019-05-09 15:58 ` [PATCH 02/17] ARCH: arm: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module Marco Felsch
2019-05-15 16:51 ` Priit Laes
2019-05-16 15:47 ` Marco Felsch
2019-05-16 16:44 ` Priit Laes
2019-05-20 2:11 ` Shawn Guo
2019-05-09 15:58 ` [PATCH 03/17] ARCH: arm: dts: imx6qdl-kontron-samx6i: add SMARC SPI0 interface Marco Felsch
2019-05-09 15:58 ` [PATCH 04/17] ARCH: arm: dts: imx6qdl-kontron-samx6i: add SMARC SDIO interface Marco Felsch
2019-05-09 15:58 ` [PATCH 05/17] ARCH: arm: dts: imx6qdl-kontron-samx6i: add SMARC LCD interface Marco Felsch
2019-05-09 15:58 ` [PATCH 06/17] ARCH: arm: dts: imx6qdl-kontron-samx6i: add SMARC Management pins Marco Felsch
2019-05-09 15:58 ` [PATCH 07/17] ARCH: arm: dts: imx6qdl-kontron-samx6i: add SMARC GPIO interface Marco Felsch
2019-05-09 15:58 ` [PATCH 08/17] ARCH: arm: dts: imx6qdl-kontron-samx6i: add SMARC HDMI interface Marco Felsch
2019-05-09 15:58 ` [PATCH 09/17] ARCH: arm: dts: imx6qdl-kontron-samx6i: add SMARC CSI Camera interface Marco Felsch
2019-05-09 15:58 ` [PATCH 10/17] ARCH: arm: dts: imx6qdl-kontron-samx6i: add SMARC I2S interface Marco Felsch
2019-05-09 15:58 ` [PATCH 11/17] ARCH: arm: dts: imx6qdl-kontron-samx6i: add SMARC SPI1 interface Marco Felsch
2019-05-16 11:43 ` Fabio Estevam
2019-05-16 11:43 ` Fabio Estevam
2019-05-16 15:47 ` Marco Felsch
2019-05-09 15:58 ` [PATCH 12/17] ARCH: arm: dts: imx6qdl-kontron-samx6i: add SMARC Watchdog Marco Felsch
2019-05-09 15:58 ` [PATCH 13/17] ARCH: arm: dts: imx6qdl-kontron-samx6i: add SMARC module eeprom Marco Felsch
2019-05-09 15:58 ` [PATCH 14/17] ARCH: arm: dts: imx6qdl-kontron-samx6i: add boot spi-nor Marco Felsch
2019-05-09 15:58 ` [PATCH 15/17] ARCH: arm: dts: imx6qdl-kontron-samx6i: add power management support Marco Felsch
2019-05-09 15:58 ` [PATCH 16/17] ARCH: arm: dts: imx6q-kontron-samx6i: add Kontron SMARC Quad/Dual SoM Marco Felsch
2019-05-09 15:58 ` [PATCH 17/17] ARCH: arm: dts: imx6dl-kontron-samx6i: add Kontron SMARC Dual-Lite/Solo SoM Marco Felsch
2019-05-20 1:29 ` [PATCH 00/17] Add Support for Kontron SMARC-sAMX6i Shawn Guo
2019-05-20 2:16 ` Shawn Guo
2019-05-21 8:29 ` Marco Felsch
2019-05-21 9:11 ` Shawn Guo
2019-05-22 10:57 ` Marco Felsch
2019-05-23 0:24 ` Shawn Guo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190509155834.22838-1-m.felsch@pengutronix.de \
--to=m.felsch@pengutronix.de \
--cc=Gilles.Buloz@kontron.com \
--cc=Michael.Brunner@kontron.com \
--cc=Stefan.Nickl@kontron.com \
--cc=devicetree@vger.kernel.org \
--cc=frieder.schrempf@kontron.de \
--cc=kernel@pengutronix.de \
--cc=linux-imx@nxp.com \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
--cc=thomas.schaefer@kontron.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).