[PATCH v3 0/2] Enable wm8524 codec on i.MX8MM EVK

[PATCH v3 0/2] Enable wm8524 codec on i.MX8MM EVK

[Daniel Baluta]

This patch series introduces the SAI nodes on i.MX8MM EVK then
creates the wm8524 codec node and finally uses simple card machine
driver to create a sound card.

Changes since v2:
	- place compatible strings one a single lines
	- move GPIO pinctrl in a node of its own
	- remove codec phandle

Changes since v1:
        - use "fsl,imx8mm-sai", "fsl,imx8mq-sai" compatbile strings and
          remove "fsl,imx6sx-sai" because SAI module on i.MX8M is not
          compatbile with SAI modules form i.MX6

Daniel Baluta (2):
  arm64: dts: imx8mm: Add SAI nodes
  arm64: dts: imx8mm-evk: Enable audio codec wm8524

 arch/arm64/boot/dts/freescale/imx8mm-evk.dts | 55 ++++++++++++++++
 arch/arm64/boot/dts/freescale/imx8mm.dtsi    | 66 ++++++++++++++++++++
 2 files changed, 121 insertions(+)

-- 
2.17.1

[PATCH v3 1/2] arm64: dts: imx8mm: Add SAI nodes

[Daniel Baluta]

i.MX8MM has 5 SAI instances with the following base
addresses according to RM.

SAI1 base address: 3001_0000h
SAI2 base address: 3002_0000h
SAI3 base address: 3003_0000h
SAI5 base address: 3005_0000h
SAI6 base address: 3006_0000h

Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
---
 arch/arm64/boot/dts/freescale/imx8mm.dtsi | 66 +++++++++++++++++++++++
 1 file changed, 66 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
index 6b407a94c06e..52abe2d03f31 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
@@ -201,6 +201,72 @@
 			#size-cells = <1>;
 			ranges;
 
+			sai1: sai@30010000 {
+				compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+				reg = <0x30010000 0x10000>;
+				interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX8MM_CLK_SAI1_IPG>,
+					 <&clk IMX8MM_CLK_SAI1_ROOT>,
+					 <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>;
+				clock-names = "bus", "mclk1", "mclk2", "mclk3";
+				dmas = <&sdma2 0 2 0>, <&sdma2 1 2 0>;
+				dma-names = "rx", "tx";
+				status = "disabled";
+			};
+
+			sai2: sai@30020000 {
+				compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+				reg = <0x30020000 0x10000>;
+				interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX8MM_CLK_SAI2_IPG>,
+					<&clk IMX8MM_CLK_SAI2_ROOT>,
+					<&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>;
+				clock-names = "bus", "mclk1", "mclk2", "mclk3";
+				dmas = <&sdma2 2 2 0>, <&sdma2 3 2 0>;
+				dma-names = "rx", "tx";
+				status = "disabled";
+			};
+
+			sai3: sai@30030000 {
+				#sound-dai-cells = <0>;
+				compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+				reg = <0x30030000 0x10000>;
+				interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX8MM_CLK_SAI3_IPG>,
+					 <&clk IMX8MM_CLK_SAI3_ROOT>,
+					 <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>;
+				clock-names = "bus", "mclk1", "mclk2", "mclk3";
+				dmas = <&sdma2 4 2 0>, <&sdma2 5 2 0>;
+				dma-names = "rx", "tx";
+				status = "disabled";
+			};
+
+			sai5: sai@30050000 {
+				compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+				reg = <0x30050000 0x10000>;
+				interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX8MM_CLK_SAI5_IPG>,
+					 <&clk IMX8MM_CLK_SAI5_ROOT>,
+					 <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>;
+				clock-names = "bus", "mclk1", "mclk2", "mclk3";
+				dmas = <&sdma2 8 2 0>, <&sdma2 9 2 0>;
+				dma-names = "rx", "tx";
+				status = "disabled";
+			};
+
+			sai6: sai@30060000 {
+				compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+				reg = <0x30060000 0x10000>;
+				interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX8MM_CLK_SAI6_IPG>,
+					 <&clk IMX8MM_CLK_SAI6_ROOT>,
+					 <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>;
+				clock-names = "bus", "mclk1", "mclk2", "mclk3";
+				dmas = <&sdma2 10 2 0>, <&sdma2 11 2 0>;
+				dma-names = "rx", "tx";
+				status = "disabled";
+			};
+
 			gpio1: gpio@30200000 {
 				compatible = "fsl,imx8mm-gpio", "fsl,imx35-gpio";
 				reg = <0x30200000 0x10000>;
-- 
2.17.1

[PATCH v3 2/2] arm64: dts: imx8mm-evk: Enable audio codec wm8524

[Daniel Baluta]

i.MX8MM has one wm8524 audio codec connected with
SAI3 digital audio interface.

This patch uses simple-card machine driver in order
to enable wm8524 codec.

We need to set:
	* SAI3 pinctrl configuration
	* codec reset gpio pinctrl configuration
	* clock hierarchy
	* codec node
	* simple-card configuration

Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
---
 arch/arm64/boot/dts/freescale/imx8mm-evk.dts | 55 ++++++++++++++++++++
 1 file changed, 55 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
index 2d5d89475b76..7c578d8762b9 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
@@ -37,6 +37,37 @@
 		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 	};
+
+	wm8524: audio-codec {
+		#sound-dai-cells = <0>;
+		compatible = "wlf,wm8524";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_wlf>;
+		wlf,mute-gpios = <&gpio5 21 GPIO_ACTIVE_LOW>;
+	};
+
+	sound-wm8524 {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "wm8524-audio";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,frame-master = <&cpudai>;
+		simple-audio-card,bitclock-master = <&cpudai>;
+		simple-audio-card,widgets =
+			"Line", "Left Line Out Jack",
+			"Line", "Right Line Out Jack";
+		simple-audio-card,routing =
+			"Left Line Out Jack", "LINEVOUTL",
+			"Right Line Out Jack", "LINEVOUTR";
+
+		cpudai: simple-audio-card,cpu {
+			sound-dai = <&sai3>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&wm8524>;
+			clocks = <&clk IMX8MM_CLK_SAI3_ROOT>;
+		};
+	};
 };
 
 &fec1 {
@@ -61,6 +92,15 @@
 	};
 };
 
+&sai3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai3>;
+	assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
+	assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
+	assigned-clock-rates = <24576000>;
+	status = "okay";
+};
+
 &uart2 { /* console */
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart2>;
@@ -124,12 +164,27 @@
 		>;
 	};
 
+	pinctrl_gpio_wlf: gpiowlfgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C4_SDA_GPIO5_IO21        0xd6
+		>;
+	};
+
 	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
 		fsl,pins = <
 			MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19	0x41
 		>;
 	};
 
+	pinctrl_sai3: sai3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC     0xd6
+			MX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK      0xd6
+			MX8MM_IOMUXC_SAI3_MCLK_SAI3_MCLK        0xd6
+			MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0     0xd6
+		>;
+	};
+
 	pinctrl_uart2: uart2grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX	0x140
-- 
2.17.1

Re: [PATCH v3 0/2] Enable wm8524 codec on i.MX8MM EVK

[Shawn Guo]

On Wed, Apr 24, 2019 at 03:04:12PM +0000, Daniel Baluta wrote:
> This patch series introduces the SAI nodes on i.MX8MM EVK then
> creates the wm8524 codec node and finally uses simple card machine
> driver to create a sound card.
> 
> Changes since v2:
> 	- place compatible strings one a single lines
> 	- move GPIO pinctrl in a node of its own
> 	- remove codec phandle
> 
> Changes since v1:
>         - use "fsl,imx8mm-sai", "fsl,imx8mq-sai" compatbile strings and
>           remove "fsl,imx6sx-sai" because SAI module on i.MX8M is not
>           compatbile with SAI modules form i.MX6
> 
> Daniel Baluta (2):
>   arm64: dts: imx8mm: Add SAI nodes
>   arm64: dts: imx8mm-evk: Enable audio codec wm8524

Hi Marco,

Are you fine with this version?

Shawn