From: Igor Opaniuk <igor.opaniuk@gmail.com>
To: devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org
Cc: robh+dt@kernel.org, mark.rutland@arm.com, shawnguo@kernel.org,
s.hauer@pengutronix.de, kernel@pengutronix.de,
festevam@gmail.com, linux-imx@nxp.com, marcel@ziswiler.com,
marcel.ziswiler@toradex.com, stefan@agner.ch
Subject: [PATCH 1/1] ARM: dts: imx6ull-colibri: enable UHS-I for USDHC1
Date: Thu, 6 Jun 2019 12:06:12 +0300 [thread overview]
Message-ID: <20190606090612.16685-1-igor.opaniuk@gmail.com> (raw)
From: Igor Opaniuk <igor.opaniuk@toradex.com>
Allows to use the SD interface at a higher speed mode if the card
supports it. For this the signaling voltage is switched from 3.3V to
1.8V under the usdhc1's drivers control.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
---
arch/arm/boot/dts/imx6ul.dtsi | 4 ++++
arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi | 11 +++++++++--
arch/arm/boot/dts/imx6ull-colibri.dtsi | 6 ++++++
3 files changed, 19 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/imx6ul.dtsi b/arch/arm/boot/dts/imx6ul.dtsi
index fc388b84bf22..91a0ced44e27 100644
--- a/arch/arm/boot/dts/imx6ul.dtsi
+++ b/arch/arm/boot/dts/imx6ul.dtsi
@@ -857,6 +857,8 @@
<&clks IMX6UL_CLK_USDHC1>,
<&clks IMX6UL_CLK_USDHC1>;
clock-names = "ipg", "ahb", "per";
+ fsl,tuning-step= <2>;
+ fsl,tuning-start-tap = <20>;
bus-width = <4>;
status = "disabled";
};
@@ -870,6 +872,8 @@
<&clks IMX6UL_CLK_USDHC2>;
clock-names = "ipg", "ahb", "per";
bus-width = <4>;
+ fsl,tuning-step= <2>;
+ fsl,tuning-start-tap = <20>;
status = "disabled";
};
diff --git a/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi b/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
index 006690ea98c0..7dc7770cf52c 100644
--- a/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
+++ b/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
@@ -145,13 +145,20 @@
};
&usdhc1 {
- pinctrl-names = "default";
+ pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_snvs_usdhc1_cd>;
- no-1-8-v;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_snvs_usdhc1_cd>;
+ pinctrl-2 = <&pinctrl_usdhc1_100mhz &pinctrl_snvs_usdhc1_cd>;
+ pinctrl-3 = <&pinctrl_usdhc1 &pinctrl_snvs_usdhc1_sleep_cd>;
cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
disable-wp;
wakeup-source;
keep-power-in-suspend;
vmmc-supply = <®_3v3>;
+ vqmmc-supply = <®_sd1_vmmc>;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
status = "okay";
};
diff --git a/arch/arm/boot/dts/imx6ull-colibri.dtsi b/arch/arm/boot/dts/imx6ull-colibri.dtsi
index 9ad1da159768..d56728f03c35 100644
--- a/arch/arm/boot/dts/imx6ull-colibri.dtsi
+++ b/arch/arm/boot/dts/imx6ull-colibri.dtsi
@@ -545,6 +545,12 @@
>;
};
+ pinctrl_snvs_usdhc1_sleep_cd: snvs-usdhc1-cd-grp-slp {
+ fsl,pins = <
+ MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x0
+ >;
+ };
+
pinctrl_snvs_wifi_pdn: snvs-wifi-pdn-grp {
fsl,pins = <
MX6ULL_PAD_BOOT_MODE1__GPIO5_IO11 0x14
--
2.17.1
next reply other threads:[~2019-06-06 9:06 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-06-06 9:06 Igor Opaniuk [this message]
2019-06-06 10:31 ` [PATCH 1/1] ARM: dts: imx6ull-colibri: enable UHS-I for USDHC1 Marcel Ziswiler
2019-06-12 10:45 ` Shawn Guo
2019-06-12 12:17 ` Stefan Agner
2019-06-12 12:49 ` Igor Opaniuk
2019-06-12 13:38 ` Shawn Guo
2019-06-12 14:29 ` Igor Opaniuk
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190606090612.16685-1-igor.opaniuk@gmail.com \
--to=igor.opaniuk@gmail.com \
--cc=devicetree@vger.kernel.org \
--cc=festevam@gmail.com \
--cc=kernel@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-imx@nxp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=marcel.ziswiler@toradex.com \
--cc=marcel@ziswiler.com \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=s.hauer@pengutronix.de \
--cc=shawnguo@kernel.org \
--cc=stefan@agner.ch \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).