Re: [PATCH 1/1] ARM: dts: imx6ull-colibri: enable UHS-I for USDHC1

[Shawn Guo <shawnguo@kernel.org>]

On Wed, Jun 12, 2019 at 03:49:03PM +0300, Igor Opaniuk wrote:
> Hi Stefan,
> 
> On Wed, Jun 12, 2019 at 3:17 PM Stefan Agner <stefan@agner.ch> wrote:
> >
> > On 06.06.2019 11:06, Igor Opaniuk wrote:
> > > From: Igor Opaniuk <igor.opaniuk@toradex.com>
> > >
> > > Allows to use the SD interface at a higher speed mode if the card
> > > supports it. For this the signaling voltage is switched from 3.3V to
> > > 1.8V under the usdhc1's drivers control.
> > >
> > > Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
> > > ---
> > >  arch/arm/boot/dts/imx6ul.dtsi                  |  4 ++++
> > >  arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi | 11 +++++++++--
> > >  arch/arm/boot/dts/imx6ull-colibri.dtsi         |  6 ++++++
> > >  3 files changed, 19 insertions(+), 2 deletions(-)
> > >
> > > diff --git a/arch/arm/boot/dts/imx6ul.dtsi b/arch/arm/boot/dts/imx6ul.dtsi
> > > index fc388b84bf22..91a0ced44e27 100644
> > > --- a/arch/arm/boot/dts/imx6ul.dtsi
> > > +++ b/arch/arm/boot/dts/imx6ul.dtsi
> > > @@ -857,6 +857,8 @@
> > >                                        <&clks IMX6UL_CLK_USDHC1>,
> > >                                        <&clks IMX6UL_CLK_USDHC1>;
> > >                               clock-names = "ipg", "ahb", "per";
> > > +                             fsl,tuning-step= <2>;
> > > +                             fsl,tuning-start-tap = <20>;
> > >                               bus-width = <4>;
> > >                               status = "disabled";
> > >                       };
> > > @@ -870,6 +872,8 @@
> > >                                        <&clks IMX6UL_CLK_USDHC2>;
> > >                               clock-names = "ipg", "ahb", "per";
> > >                               bus-width = <4>;
> > > +                             fsl,tuning-step= <2>;
> > > +                             fsl,tuning-start-tap = <20>;
> > >                               status = "disabled";
> > >                       };
> > >
> > > diff --git a/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
> > > b/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
> > > index 006690ea98c0..7dc7770cf52c 100644
> > > --- a/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
> > > +++ b/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
> > > @@ -145,13 +145,20 @@
> > >  };
> > >
> > >  &usdhc1 {
> > > -     pinctrl-names = "default";
> > > +     pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
> > >       pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_snvs_usdhc1_cd>;
> > > -     no-1-8-v;
> > > +     pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_snvs_usdhc1_cd>;
> > > +     pinctrl-2 = <&pinctrl_usdhc1_100mhz &pinctrl_snvs_usdhc1_cd>;
> >
> > Should that not be pinctrl_usdhc1_200mhz?
> >
> 
> Correct, thanks for pointing this out.
> Taking into account that the patch was already accepted by Shawn, will
> send another to fix this typo ASAP (added to my todo list).

I just fixed it up on my branch.

Shawn