[PATCH v4 0/2] Add basic support for pico-pi-imx8m

devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed

* [PATCH v4 0/2] Add basic support for pico-pi-imx8m
@ 2019-07-19 10:48 andradanciu1997
  2019-07-19 10:48 ` [PATCH v4 1/2] arm64: dts: fsl: pico-pi: Add a device tree for the PICO-PI-IMX8M andradanciu1997
  2019-07-19 10:48 ` [PATCH v4 2/2] dt-bindings: arm: fsl: Add the pico-pi-imx8m board andradanciu1997
  0 siblings, 2 replies; 6+ messages in thread
From: andradanciu1997 @ 2019-07-19 10:48 UTC (permalink / raw)
  To: shawnguo
  Cc: robh+dt, mark.rutland, s.hauer, kernel, festevam, linux-imx,
	andrew.smirnov, manivannan.sadhasivam, ping.bai, Michal.Vokac,
	leoyang.li, sriram.dash, l.stach, vabhav.sharma, bhaskar.upadhaya,
	pramod.kumar_1, pankaj.bansal, aisheng.dong, angus, richard.hu,
	andradanciu1997, devicetree, linux-kernel, linux-arm-kernel

Add support for TechNexion PICO-PI-IMX8M based on patches from Richard Hu
Datasheet is at: https://s3.us-east-2.amazonaws.com/technexion/datasheets/picopiimx8m.pdf

Changes since v3:
 - renamed pico-pi-8m.dts to imx8mq-pico-pi.dts
 - moved iomuxc node as the last one
 - removed pinctrl-assert-gpios property from fec1 node
 - removed at803x,led-act-blind-workaround, at803x,eee-disabled
   properties from mdio node
 - added pinctrl-names = "default" to i2c1 node
 - changed bd71837 pmic support properties according to
   Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt
 - removed A53_0 node

Changes since v2:
 - changed PICO-PI-8M bord compatible from wand,imx8mq-pico-pi to
   technexion,pico-pi-imx8m
 - removed bootargs property
 - removed regulators node and put fixed regulator directly under root node
 - changed node name from usb_otg_vbus to regulator-usb-otg-vbus
 - removed pinctrl-names property from iomuxc node
 - removed wand-pi-8m container node
 - sorted pinctrl nodes alphabetically
 - removed tusb320_irqgrp, tusb320_irqgrp nodes because there is no upstream
   driver
 - changed properties' order in usb_dwc3_1 node

Changes since v1:
 - renamed wandboard-pi-8m.dts to pico-pi-8m.dts
 - removed pinctrl_csi1, pinctrl_wifi_ctrl
 - used generic name for pmic
 - removed gpo node
 - delete regulator-virtuals node
 - remove always-on property from buck1-8 and ldo3-7
 - remove pmic-buck-uses-i2c-dvs property for buck1-4

Andra Danciu (1):
  dt-bindings: arm: fsl: Add the pico-pi-imx8m board

Richard Hu (1):
  arm64: dts: fsl: pico-pi: Add a device tree for the PICO-PI-IMX8M

 Documentation/devicetree/bindings/arm/fsl.yaml   |   1 +
 arch/arm64/boot/dts/freescale/Makefile           |   1 +
 arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts | 417 +++++++++++++++++++++++
 3 files changed, 419 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts

-- 
2.11.0

^ permalink raw reply	[flat|nested] 6+ messages in thread

* [PATCH v4 1/2] arm64: dts: fsl: pico-pi: Add a device tree for the PICO-PI-IMX8M
  2019-07-19 10:48 [PATCH v4 0/2] Add basic support for pico-pi-imx8m andradanciu1997
@ 2019-07-19 10:48 ` andradanciu1997
  2019-07-19 11:19   ` Fabio Estevam
  2019-07-19 10:48 ` [PATCH v4 2/2] dt-bindings: arm: fsl: Add the pico-pi-imx8m board andradanciu1997
  1 sibling, 1 reply; 6+ messages in thread
From: andradanciu1997 @ 2019-07-19 10:48 UTC (permalink / raw)
  To: shawnguo
  Cc: robh+dt, mark.rutland, s.hauer, kernel, festevam, linux-imx,
	andrew.smirnov, manivannan.sadhasivam, ping.bai, Michal.Vokac,
	leoyang.li, sriram.dash, l.stach, vabhav.sharma, bhaskar.upadhaya,
	pramod.kumar_1, pankaj.bansal, aisheng.dong, angus, richard.hu,
	andradanciu1997, devicetree, linux-kernel, linux-arm-kernel

From: Richard Hu <richard.hu@technexion.com>

TechNexion PICO-PI-IMX8M-DEV evaluation and development kit based on
NXP i.MX8M Quad applications processor. Datasheet can be found at:

https://s3.us-east-2.amazonaws.com/technexion/datasheets/picopiimx8m.pdf

The current level of support yields a working console and is able to boot
userspace from NFS or init ramdisk.

Additional subsystems that are active :
	- Ethernet
	- USB

Cc: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Richard Hu <richard.hu@technexion.com>
Signed-off-by: Andra Danciu <andradanciu1997@gmail.com>
---
 arch/arm64/boot/dts/freescale/Makefile           |   1 +
 arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts | 417 +++++++++++++++++++++++
 2 files changed, 418 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index c043aca66572..99627a499a73 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -23,6 +23,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mq-pico-pi.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts b/arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts
new file mode 100644
index 000000000000..179b213a816f
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts
@@ -0,0 +1,417 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2018 Wandboard, Org.
+ * Copyright 2017 NXP
+ *
+ * Author: Richard Hu <hakahu@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "imx8mq.dtsi"
+
+/ {
+	model = "TechNexion PICO-PI-8M";
+	compatible = "technexion,pico-pi-imx8m", "fsl,imx8mq";
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	pmic_osc: clock-pmic {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "pmic_osc";
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_otg_vbus>;
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 14 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1 &pinctrl_enet_3v3>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	pmic: pmic@4b {
+		reg = <0x4b>;
+		compatible = "rohm,bd71837";
+		/* PMIC BD71837 PMIC_nINT GPIO1_IO12 */
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		clocks = <&pmic_osc>;
+		clock-names = "osc";
+		clock-output-names = "pmic_clk";
+		interrupt-parent = <&gpio1>;
+		interrupts = <3 GPIO_ACTIVE_LOW>;
+		interrupt-names = "irq";
+
+		regulators {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			buck1: BUCK1 {
+				regulator-name = "buck1";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				regulator-ramp-delay = <1250>;
+				rohm,dvs-run-voltage = <900000>;
+				rohm,dvs-idle-voltage = <850000>;
+				rohm,dvs-suspend-voltage = <800000>;
+			};
+
+			buck2: BUCK2 {
+				regulator-name = "buck2";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				regulator-ramp-delay = <1250>;
+				rohm,dvs-run-voltage = <1000000>;
+				rohm,dvs-idle-voltage = <900000>;
+			};
+
+			buck3: BUCK3 {
+				regulator-name = "buck3";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				rohm,dvs-run-voltage = <1000000>;
+			};
+
+			buck4: BUCK4 {
+				regulator-name = "buck4";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				rohm,dvs-run-voltage = <1000000>;
+			};
+
+			buck5: BUCK5 {
+				regulator-name = "buck5";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-boot-on;
+			};
+
+			buck6: BUCK6 {
+				regulator-name = "buck6";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+			};
+
+			buck7: BUCK7 {
+				regulator-name = "buck7";
+				regulator-min-microvolt = <1605000>;
+				regulator-max-microvolt = <1995000>;
+				regulator-boot-on;
+			};
+
+			buck8: BUCK8 {
+				regulator-name = "buck8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-boot-on;
+			};
+
+			ldo1: LDO1 {
+				regulator-name = "ldo1";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2: LDO2 {
+				regulator-name = "ldo2";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo3: LDO3 {
+				regulator-name = "ldo3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+			};
+
+			ldo4: LDO4 {
+				regulator-name = "ldo4";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+			};
+
+			ldo5: LDO5 {
+				regulator-name = "ldo5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+			};
+
+			ldo6: LDO6 {
+				regulator-name = "ldo6";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+			};
+
+			ldo7: LDO7 {
+				regulator-name = "ldo7";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+			};
+		};
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&uart1 { /* console */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	bus-width = <4>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&usb3_phy0 {
+	status = "okay";
+};
+
+&usb3_phy1 {
+	status = "okay";
+};
+
+&usb_dwc3_1 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_enet_3v3: enet3v3grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_GPIO1_IO00_GPIO1_IO0	0x19
+		>;
+	};
+
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC		0x3
+			MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO	0x23
+			MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3	0x1f
+			MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2	0x1f
+			MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1	0x1f
+			MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0	0x1f
+			MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3	0x91
+			MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2	0x91
+			MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1	0x91
+			MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0	0x91
+			MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC	0x1f
+			MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC	0x91
+			MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
+			MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
+			MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9	0x19
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL			0x4000007f
+			MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA			0x4000007f
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL			0x4000007f
+			MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA			0x4000007f
+		>;
+	};
+
+	pinctrl_otg_vbus: otgvbusgrp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_NAND_DQS_GPIO3_IO14		0x19   /* USB OTG VBUS Enable */
+		>;
+	};
+
+	pinctrl_pmic: pmicirq {
+		fsl,pins = <
+			MX8MQ_IOMUXC_GPIO1_IO03_GPIO1_IO3	0x41
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX		0x49
+			MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX		0x49
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX		0x49
+			MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX		0x49
+			MX8MQ_IOMUXC_UART4_RXD_UART2_DCE_CTS_B		0x49
+			MX8MQ_IOMUXC_UART4_TXD_UART2_DCE_RTS_B		0x49
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x83
+			MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xc3
+			MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0		0xc3
+			MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1		0xc3
+			MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2		0xc3
+			MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3		0xc3
+			MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4		0xc3
+			MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5		0xc3
+			MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6		0xc3
+			MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7		0xc3
+			MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x83
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x85
+			MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xc5
+			MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0		0xc5
+			MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1		0xc5
+			MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2		0xc5
+			MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3		0xc5
+			MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4		0xc5
+			MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5		0xc5
+			MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6		0xc5
+			MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7		0xc5
+			MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x85
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x87
+			MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xc7
+			MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0		0xc7
+			MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1		0xc7
+			MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2		0xc7
+			MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3		0xc7
+			MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4		0xc7
+			MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5		0xc7
+			MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6		0xc7
+			MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7		0xc7
+			MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x87
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2grpgpio {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12	0x41
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x83
+			MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xc3
+			MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0		0xc3
+			MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1		0xc3
+			MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2		0xc3
+			MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3		0xc3
+			MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xc1
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x85
+			MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xc5
+			MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0		0xc5
+			MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1		0xc5
+			MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2		0xc5
+			MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3		0xc5
+			MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xc1
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x87
+			MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xc7
+			MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0		0xc7
+			MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1		0xc7
+			MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2		0xc7
+			MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3		0xc7
+			MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xc1
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
+		>;
+	};
+};
-- 
2.11.0

^ permalink raw reply related	[flat|nested] 6+ messages in thread

* Re: [PATCH v4 1/2] arm64: dts: fsl: pico-pi: Add a device tree for the PICO-PI-IMX8M
  2019-07-19 10:48 ` [PATCH v4 1/2] arm64: dts: fsl: pico-pi: Add a device tree for the PICO-PI-IMX8M andradanciu1997
@ 2019-07-19 11:19   ` Fabio Estevam
  2019-07-19 11:49     ` Andra Danciu
  2019-07-19 12:04     ` Daniel Baluta
  0 siblings, 2 replies; 6+ messages in thread
From: Fabio Estevam @ 2019-07-19 11:19 UTC (permalink / raw)
  To: andradanciu1997
  Cc: Shawn Guo, Rob Herring, Mark Rutland, Sascha Hauer, Sascha Hauer,
	NXP Linux Team, Andrey Smirnov, Manivannan Sadhasivam, Ping Bai,
	Michal Vokáč, Li Yang, sriram.dash, Lucas Stach,
	Vabhav Sharma, Bhaskar Upadhaya, Pramod Kumar, pankaj.bansal,
	Dong Aisheng, Angus Ainslie (Purism), Richard Hu

Hi Andra,

On Fri, Jul 19, 2019 at 7:48 AM andradanciu1997
<andradanciu1997@gmail.com> wrote:

> +       pmic: pmic@4b {
> +               reg = <0x4b>;
> +               compatible = "rohm,bd71837";
> +               /* PMIC BD71837 PMIC_nINT GPIO1_IO12 */
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&pinctrl_pmic>;
> +               clocks = <&pmic_osc>;
> +               clock-names = "osc";
> +               clock-output-names = "pmic_clk";
> +               interrupt-parent = <&gpio1>;
> +               interrupts = <3 GPIO_ACTIVE_LOW>;
> +               interrupt-names = "irq";
> +
> +               regulators {
> +                       #address-cells = <1>;
> +                       #size-cells = <0>;

#address-cells and  #size-cells are not needed and they cause warnings with W=1:

  DTC     arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dtb
arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts:77.14-196.5: Warning
(avoid_unnecessary_addr_size):
/soc@0/bus@30800000/i2c@30a20000/pmic@4b/regulators: unnecessary
#address-cells/#size-cells without "ranges" or child "reg" property

Please remove them.

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH v4 1/2] arm64: dts: fsl: pico-pi: Add a device tree for the PICO-PI-IMX8M
  2019-07-19 11:19   ` Fabio Estevam
@ 2019-07-19 11:49     ` Andra Danciu
  2019-07-19 12:04     ` Daniel Baluta
  1 sibling, 0 replies; 6+ messages in thread
From: Andra Danciu @ 2019-07-19 11:49 UTC (permalink / raw)
  To: Fabio Estevam
  Cc: Shawn Guo, Rob Herring, Mark Rutland, Sascha Hauer, Sascha Hauer,
	NXP Linux Team, Andrey Smirnov, Manivannan Sadhasivam, Ping Bai,
	Michal Vokáč, Li Yang, sriram.dash, Lucas Stach,
	Vabhav Sharma, Bhaskar Upadhaya, Pramod Kumar, pankaj.bansal,
	Dong Aisheng, Angus Ainslie (Purism), Richard Hu

Hi Fabio,

I compiled with W=1 and you are right, they cause warning. I will remove them.

În vin., 19 iul. 2019 la 14:19, Fabio Estevam <festevam@gmail.com> a scris:
>
> Hi Andra,
>
> On Fri, Jul 19, 2019 at 7:48 AM andradanciu1997
> <andradanciu1997@gmail.com> wrote:
>
> > +       pmic: pmic@4b {
> > +               reg = <0x4b>;
> > +               compatible = "rohm,bd71837";
> > +               /* PMIC BD71837 PMIC_nINT GPIO1_IO12 */
> > +               pinctrl-names = "default";
> > +               pinctrl-0 = <&pinctrl_pmic>;
> > +               clocks = <&pmic_osc>;
> > +               clock-names = "osc";
> > +               clock-output-names = "pmic_clk";
> > +               interrupt-parent = <&gpio1>;
> > +               interrupts = <3 GPIO_ACTIVE_LOW>;
> > +               interrupt-names = "irq";
> > +
> > +               regulators {
> > +                       #address-cells = <1>;
> > +                       #size-cells = <0>;
>
> #address-cells and  #size-cells are not needed and they cause warnings with W=1:
>
>   DTC     arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dtb
> arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts:77.14-196.5: Warning
> (avoid_unnecessary_addr_size):
> /soc@0/bus@30800000/i2c@30a20000/pmic@4b/regulators: unnecessary
> #address-cells/#size-cells without "ranges" or child "reg" property
>
> Please remove them.

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH v4 1/2] arm64: dts: fsl: pico-pi: Add a device tree for the PICO-PI-IMX8M
  2019-07-19 11:19   ` Fabio Estevam
  2019-07-19 11:49     ` Andra Danciu
@ 2019-07-19 12:04     ` Daniel Baluta
  1 sibling, 0 replies; 6+ messages in thread
From: Daniel Baluta @ 2019-07-19 12:04 UTC (permalink / raw)
  To: Fabio Estevam
  Cc: andradanciu1997, Shawn Guo, Rob Herring, Mark Rutland,
	Sascha Hauer, Sascha Hauer, NXP Linux Team, Andrey Smirnov,
	Manivannan Sadhasivam, Ping Bai, Michal Vokáč, Li Yang,
	sriram.dash, Lucas Stach, Vabhav Sharma, Bhaskar Upadhaya,
	Pramod Kumar, pankaj.bansal, Dong Aisheng, Angus Ainslie (Purism)

On Fri, Jul 19, 2019 at 2:22 PM Fabio Estevam <festevam@gmail.com> wrote:
>
> Hi Andra,
>
> On Fri, Jul 19, 2019 at 7:48 AM andradanciu1997
> <andradanciu1997@gmail.com> wrote:
>
> > +       pmic: pmic@4b {
> > +               reg = <0x4b>;
> > +               compatible = "rohm,bd71837";
> > +               /* PMIC BD71837 PMIC_nINT GPIO1_IO12 */
> > +               pinctrl-names = "default";
> > +               pinctrl-0 = <&pinctrl_pmic>;
> > +               clocks = <&pmic_osc>;
> > +               clock-names = "osc";
> > +               clock-output-names = "pmic_clk";
> > +               interrupt-parent = <&gpio1>;
> > +               interrupts = <3 GPIO_ACTIVE_LOW>;
> > +               interrupt-names = "irq";
> > +
> > +               regulators {
> > +                       #address-cells = <1>;
> > +                       #size-cells = <0>;
>
> #address-cells and  #size-cells are not needed and they cause warnings with W=1:
>
>   DTC     arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dtb
> arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts:77.14-196.5: Warning
> (avoid_unnecessary_addr_size):
> /soc@0/bus@30800000/i2c@30a20000/pmic@4b/regulators: unnecessary
> #address-cells/#size-cells without "ranges" or child "reg" property
>
> Please remove them.

Thanks Fabio for review, we learned something new today :).

Daniel.

^ permalink raw reply	[flat|nested] 6+ messages in thread

* [PATCH v4 2/2] dt-bindings: arm: fsl: Add the pico-pi-imx8m board
  2019-07-19 10:48 [PATCH v4 0/2] Add basic support for pico-pi-imx8m andradanciu1997
  2019-07-19 10:48 ` [PATCH v4 1/2] arm64: dts: fsl: pico-pi: Add a device tree for the PICO-PI-IMX8M andradanciu1997
@ 2019-07-19 10:48 ` andradanciu1997
  1 sibling, 0 replies; 6+ messages in thread
From: andradanciu1997 @ 2019-07-19 10:48 UTC (permalink / raw)
  To: shawnguo
  Cc: robh+dt, mark.rutland, s.hauer, kernel, festevam, linux-imx,
	andrew.smirnov, manivannan.sadhasivam, ping.bai, Michal.Vokac,
	leoyang.li, sriram.dash, l.stach, vabhav.sharma, bhaskar.upadhaya,
	pramod.kumar_1, pankaj.bansal, aisheng.dong, angus, richard.hu,
	andradanciu1997, devicetree, linux-kernel, linux-arm-kernel

From: Andra Danciu <andradanciu1997@gmail.com>

Add an entry for TechNexion PICO-PI-IMX8M board based on i.MX8MQ SoC
Datasheet can be found at:
https://s3.us-east-2.amazonaws.com/technexion/datasheets/picopiimx8m.pdf

Cc: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Andra Danciu <andradanciu1997@gmail.com>
---
 Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 7294ac36f4c0..54c094341121 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -219,6 +219,7 @@ properties:
           - enum:
               - fsl,imx8mq-evk            # i.MX8MQ EVK Board
               - purism,librem5-devkit     # Purism Librem5 devkit
+              - technexion,pico-pi-imx8m  # TechNexion PICO-PI-8M evk
           - const: fsl,imx8mq
 
       - description: i.MX8QXP based Boards
-- 
2.11.0

^ permalink raw reply related	[flat|nested] 6+ messages in thread

end of thread, other threads:[~2019-07-19 12:04 UTC | newest]

Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2019-07-19 10:48 [PATCH v4 0/2] Add basic support for pico-pi-imx8m andradanciu1997
2019-07-19 10:48 ` [PATCH v4 1/2] arm64: dts: fsl: pico-pi: Add a device tree for the PICO-PI-IMX8M andradanciu1997
2019-07-19 11:19   ` Fabio Estevam
2019-07-19 11:49     ` Andra Danciu
2019-07-19 12:04     ` Daniel Baluta
2019-07-19 10:48 ` [PATCH v4 2/2] dt-bindings: arm: fsl: Add the pico-pi-imx8m board andradanciu1997

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).