* Re: [PATCH] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node
[not found] <0101016ed018cde9-da3dc3e0-de6e-4b18-9add-bc6f88511ab2-000000@us-west-2.amazonses.com>
@ 2019-12-11 7:20 ` Bjorn Andersson
2019-12-19 5:57 ` pillair
0 siblings, 1 reply; 4+ messages in thread
From: Bjorn Andersson @ 2019-12-11 7:20 UTC (permalink / raw)
To: Rakesh Pillai; +Cc: devicetree, linux-arm-msm, linux-kernel, linux-arm-kernel
On Wed 04 Dec 00:48 PST 2019, Rakesh Pillai wrote:
> Add device node for the ath10k SNOC platform driver probe
> and add resources required for WCN3990 on sc7180 soc.
>
> Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
> ---
> This change is dependent on the below set of changes
> arm64: dts: sc7180: Add qupv3_0 and qupv3_1 (https://lore.kernel.org/patchwork/patch/1150367/)
Why?
> ---
> arch/arm64/boot/dts/qcom/sc7180-idp.dts | 4 ++++
> arch/arm64/boot/dts/qcom/sc7180.dtsi | 27 +++++++++++++++++++++++++++
> 2 files changed, 31 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> index 189254f..8a6a760 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> +++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> @@ -248,6 +248,10 @@
> status = "okay";
> };
>
> +&wifi {
> + status = "okay";
Please conclude on the representation of the "skip-hyp-mem-assign" and
add it here, rather than in a subsequent patch - which implies that this
patch doesn't work on its own.
> +};
> +
> /* PINCTRL - additions to nodes defined in sc7180.dtsi */
>
> &qup_i2c2_default {
> diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> index 666e9b9..40c9971 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> @@ -42,6 +42,12 @@
> compatible = "qcom,cmd-db";
> no-map;
> };
> +
> + wlan_fw_mem: wlan_fw_region@93900000 {
wlan_fw_mem: memory@93900000 {
> + compatible = "removed-dma-pool";
> + no-map;
> + reg = <0 0x93900000 0 0x200000>;
> + };
> };
>
> cpus {
> @@ -1119,6 +1125,27 @@
> #clock-cells = <1>;
> };
> };
> +
> + wifi: wifi@18800000 {
> + status = "disabled";
> + compatible = "qcom,wcn3990-wifi";
> + reg = <0 0x18800000 0 0x800000>;
> + reg-names = "membase";
> + interrupts =
> + <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH /* CE0 */ >,
> + <GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH /* CE1 */ >,
> + <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH /* CE2 */ >,
> + <GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH /* CE3 */ >,
> + <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH /* CE4 */ >,
> + <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH /* CE5 */ >,
> + <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH /* CE6 */ >,
> + <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH /* CE7 */ >,
> + <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH /* CE8 */ >,
> + <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH /* CE9 */ >,
> + <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH /* CE10 */>,
> + <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH /* CE11 */>;
> + memory-region = <&wlan_fw_mem>;
No iommus in sc7180?
Regards,
Bjorn
> + };
> };
>
> timer {
> --
> 2.7.4
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 4+ messages in thread* RE: [PATCH] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node
2019-12-11 7:20 ` [PATCH] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node Bjorn Andersson
@ 2019-12-19 5:57 ` pillair
2019-12-19 7:20 ` Bjorn Andersson
0 siblings, 1 reply; 4+ messages in thread
From: pillair @ 2019-12-19 5:57 UTC (permalink / raw)
To: 'Bjorn Andersson'
Cc: devicetree, linux-arm-msm, linux-kernel, linux-arm-kernel
I will raise the next patchset with the comments addressed.
> -----Original Message-----
> From: Bjorn Andersson <bjorn.andersson@linaro.org>
> Sent: Wednesday, December 11, 2019 12:51 PM
> To: Rakesh Pillai <pillair@codeaurora.org>
> Cc: devicetree@vger.kernel.org; linux-arm-msm@vger.kernel.org; linux-
> kernel@vger.kernel.org; linux-arm-kernel@lists.infradead.org
> Subject: Re: [PATCH] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module
> device node
>
> On Wed 04 Dec 00:48 PST 2019, Rakesh Pillai wrote:
>
> > Add device node for the ath10k SNOC platform driver probe
> > and add resources required for WCN3990 on sc7180 soc.
> >
> > Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
> > ---
> > This change is dependent on the below set of changes
> > arm64: dts: sc7180: Add qupv3_0 and qupv3_1
> (https://lore.kernel.org/patchwork/patch/1150367/)
>
> Why?
The mentioned series of patchset brings the DTSI for sc7180.
Hence the addition of wifi node is dependent on this series
https://lore.kernel.org/patchwork/patch/1150367/
>
> > ---
> > arch/arm64/boot/dts/qcom/sc7180-idp.dts | 4 ++++
> > arch/arm64/boot/dts/qcom/sc7180.dtsi | 27
> +++++++++++++++++++++++++++
> > 2 files changed, 31 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> > index 189254f..8a6a760 100644
> > --- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> > +++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> > @@ -248,6 +248,10 @@
> > status = "okay";
> > };
> >
> > +&wifi {
> > + status = "okay";
>
> Please conclude on the representation of the "skip-hyp-mem-assign" and
> add it here, rather than in a subsequent patch - which implies that this
> patch doesn't work on its own.
Sure, I will update the next patchset.
>
> > +};
> > +
> > /* PINCTRL - additions to nodes defined in sc7180.dtsi */
> >
> > &qup_i2c2_default {
> > diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> > index 666e9b9..40c9971 100644
> > --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> > @@ -42,6 +42,12 @@
> > compatible = "qcom,cmd-db";
> > no-map;
> > };
> > +
> > + wlan_fw_mem: wlan_fw_region@93900000 {
>
> wlan_fw_mem: memory@93900000 {
>
> > + compatible = "removed-dma-pool";
> > + no-map;
> > + reg = <0 0x93900000 0 0x200000>;
> > + };
> > };
> >
> > cpus {
> > @@ -1119,6 +1125,27 @@
> > #clock-cells = <1>;
> > };
> > };
> > +
> > + wifi: wifi@18800000 {
> > + status = "disabled";
> > + compatible = "qcom,wcn3990-wifi";
> > + reg = <0 0x18800000 0 0x800000>;
> > + reg-names = "membase";
> > + interrupts =
> > + <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH /* CE0
> */ >,
> > + <GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH /* CE1
> */ >,
> > + <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH /* CE2
> */ >,
> > + <GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH /* CE3
> */ >,
> > + <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH /* CE4
> */ >,
> > + <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH /* CE5
> */ >,
> > + <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH /* CE6
> */ >,
> > + <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH /* CE7
> */ >,
> > + <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH /* CE8
> */ >,
> > + <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH /* CE9
> */ >,
> > + <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH /* CE10
> */>,
> > + <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH /* CE11
> */>;
> > + memory-region = <&wlan_fw_mem>;
>
> No iommus in sc7180?
>
> Regards,
> Bjorn
>
> > + };
> > };
> >
> > timer {
> > --
> > 2.7.4
> >
> >
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel@lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 4+ messages in thread* Re: [PATCH] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node
2019-12-19 5:57 ` pillair
@ 2019-12-19 7:20 ` Bjorn Andersson
0 siblings, 0 replies; 4+ messages in thread
From: Bjorn Andersson @ 2019-12-19 7:20 UTC (permalink / raw)
To: pillair; +Cc: devicetree, linux-arm-msm, linux-kernel, linux-arm-kernel
On Wed 18 Dec 21:57 PST 2019, pillair@codeaurora.org wrote:
> I will raise the next patchset with the comments addressed.
>
> > -----Original Message-----
> > From: Bjorn Andersson <bjorn.andersson@linaro.org>
> > Sent: Wednesday, December 11, 2019 12:51 PM
> > To: Rakesh Pillai <pillair@codeaurora.org>
> > Cc: devicetree@vger.kernel.org; linux-arm-msm@vger.kernel.org; linux-
> > kernel@vger.kernel.org; linux-arm-kernel@lists.infradead.org
> > Subject: Re: [PATCH] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module
> > device node
> >
> > On Wed 04 Dec 00:48 PST 2019, Rakesh Pillai wrote:
> >
> > > Add device node for the ath10k SNOC platform driver probe
> > > and add resources required for WCN3990 on sc7180 soc.
> > >
> > > Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
> > > ---
> > > This change is dependent on the below set of changes
> > > arm64: dts: sc7180: Add qupv3_0 and qupv3_1
> > (https://lore.kernel.org/patchwork/patch/1150367/)
> >
> > Why?
>
> The mentioned series of patchset brings the DTSI for sc7180.
> Hence the addition of wifi node is dependent on this series
> https://lore.kernel.org/patchwork/patch/1150367/
>
I see, this should all be settled now. Looking forward to v2.
Thanks,
Bjorn
>
> >
> > > ---
> > > arch/arm64/boot/dts/qcom/sc7180-idp.dts | 4 ++++
> > > arch/arm64/boot/dts/qcom/sc7180.dtsi | 27
> > +++++++++++++++++++++++++++
> > > 2 files changed, 31 insertions(+)
> > >
> > > diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> > b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> > > index 189254f..8a6a760 100644
> > > --- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> > > +++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> > > @@ -248,6 +248,10 @@
> > > status = "okay";
> > > };
> > >
> > > +&wifi {
> > > + status = "okay";
> >
> > Please conclude on the representation of the "skip-hyp-mem-assign" and
> > add it here, rather than in a subsequent patch - which implies that this
> > patch doesn't work on its own.
>
>
> Sure, I will update the next patchset.
>
>
> >
> > > +};
> > > +
> > > /* PINCTRL - additions to nodes defined in sc7180.dtsi */
> > >
> > > &qup_i2c2_default {
> > > diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> > b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> > > index 666e9b9..40c9971 100644
> > > --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> > > +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> > > @@ -42,6 +42,12 @@
> > > compatible = "qcom,cmd-db";
> > > no-map;
> > > };
> > > +
> > > + wlan_fw_mem: wlan_fw_region@93900000 {
> >
> > wlan_fw_mem: memory@93900000 {
> >
> > > + compatible = "removed-dma-pool";
> > > + no-map;
> > > + reg = <0 0x93900000 0 0x200000>;
> > > + };
> > > };
> > >
> > > cpus {
> > > @@ -1119,6 +1125,27 @@
> > > #clock-cells = <1>;
> > > };
> > > };
> > > +
> > > + wifi: wifi@18800000 {
> > > + status = "disabled";
> > > + compatible = "qcom,wcn3990-wifi";
> > > + reg = <0 0x18800000 0 0x800000>;
> > > + reg-names = "membase";
> > > + interrupts =
> > > + <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH /* CE0
> > */ >,
> > > + <GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH /* CE1
> > */ >,
> > > + <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH /* CE2
> > */ >,
> > > + <GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH /* CE3
> > */ >,
> > > + <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH /* CE4
> > */ >,
> > > + <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH /* CE5
> > */ >,
> > > + <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH /* CE6
> > */ >,
> > > + <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH /* CE7
> > */ >,
> > > + <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH /* CE8
> > */ >,
> > > + <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH /* CE9
> > */ >,
> > > + <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH /* CE10
> > */>,
> > > + <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH /* CE11
> > */>;
> > > + memory-region = <&wlan_fw_mem>;
> >
> > No iommus in sc7180?
> >
> > Regards,
> > Bjorn
> >
> > > + };
> > > };
> > >
> > > timer {
> > > --
> > > 2.7.4
> > >
> > >
> > > _______________________________________________
> > > linux-arm-kernel mailing list
> > > linux-arm-kernel@lists.infradead.org
> > > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node
@ 2019-12-04 8:48 Rakesh Pillai
0 siblings, 0 replies; 4+ messages in thread
From: Rakesh Pillai @ 2019-12-04 8:48 UTC (permalink / raw)
To: devicetree; +Cc: linux-arm-kernel, linux-kernel, linux-arm-msm, Rakesh Pillai
Add device node for the ath10k SNOC platform driver probe
and add resources required for WCN3990 on sc7180 soc.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
---
This change is dependent on the below set of changes
arm64: dts: sc7180: Add qupv3_0 and qupv3_1 (https://lore.kernel.org/patchwork/patch/1150367/)
---
arch/arm64/boot/dts/qcom/sc7180-idp.dts | 4 ++++
arch/arm64/boot/dts/qcom/sc7180.dtsi | 27 +++++++++++++++++++++++++++
2 files changed, 31 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
index 189254f..8a6a760 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
@@ -248,6 +248,10 @@
status = "okay";
};
+&wifi {
+ status = "okay";
+};
+
/* PINCTRL - additions to nodes defined in sc7180.dtsi */
&qup_i2c2_default {
diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
index 666e9b9..40c9971 100644
--- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
@@ -42,6 +42,12 @@
compatible = "qcom,cmd-db";
no-map;
};
+
+ wlan_fw_mem: wlan_fw_region@93900000 {
+ compatible = "removed-dma-pool";
+ no-map;
+ reg = <0 0x93900000 0 0x200000>;
+ };
};
cpus {
@@ -1119,6 +1125,27 @@
#clock-cells = <1>;
};
};
+
+ wifi: wifi@18800000 {
+ status = "disabled";
+ compatible = "qcom,wcn3990-wifi";
+ reg = <0 0x18800000 0 0x800000>;
+ reg-names = "membase";
+ interrupts =
+ <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH /* CE0 */ >,
+ <GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH /* CE1 */ >,
+ <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH /* CE2 */ >,
+ <GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH /* CE3 */ >,
+ <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH /* CE4 */ >,
+ <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH /* CE5 */ >,
+ <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH /* CE6 */ >,
+ <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH /* CE7 */ >,
+ <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH /* CE8 */ >,
+ <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH /* CE9 */ >,
+ <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH /* CE10 */>,
+ <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH /* CE11 */>;
+ memory-region = <&wlan_fw_mem>;
+ };
};
timer {
--
2.7.4
^ permalink raw reply related [flat|nested] 4+ messages in thread
end of thread, other threads:[~2019-12-19 7:20 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <0101016ed018cde9-da3dc3e0-de6e-4b18-9add-bc6f88511ab2-000000@us-west-2.amazonses.com>
2019-12-11 7:20 ` [PATCH] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node Bjorn Andersson
2019-12-19 5:57 ` pillair
2019-12-19 7:20 ` Bjorn Andersson
2019-12-04 8:48 Rakesh Pillai
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).