From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: pillair@codeaurora.org
Cc: devicetree@vger.kernel.org, linux-arm-msm@vger.kernel.org,
linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node
Date: Wed, 18 Dec 2019 23:20:31 -0800 [thread overview]
Message-ID: <20191219072031.GH448416@yoga> (raw)
In-Reply-To: <000b01d5b631$30ae26f0$920a74d0$@codeaurora.org>
On Wed 18 Dec 21:57 PST 2019, pillair@codeaurora.org wrote:
> I will raise the next patchset with the comments addressed.
>
> > -----Original Message-----
> > From: Bjorn Andersson <bjorn.andersson@linaro.org>
> > Sent: Wednesday, December 11, 2019 12:51 PM
> > To: Rakesh Pillai <pillair@codeaurora.org>
> > Cc: devicetree@vger.kernel.org; linux-arm-msm@vger.kernel.org; linux-
> > kernel@vger.kernel.org; linux-arm-kernel@lists.infradead.org
> > Subject: Re: [PATCH] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module
> > device node
> >
> > On Wed 04 Dec 00:48 PST 2019, Rakesh Pillai wrote:
> >
> > > Add device node for the ath10k SNOC platform driver probe
> > > and add resources required for WCN3990 on sc7180 soc.
> > >
> > > Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
> > > ---
> > > This change is dependent on the below set of changes
> > > arm64: dts: sc7180: Add qupv3_0 and qupv3_1
> > (https://lore.kernel.org/patchwork/patch/1150367/)
> >
> > Why?
>
> The mentioned series of patchset brings the DTSI for sc7180.
> Hence the addition of wifi node is dependent on this series
> https://lore.kernel.org/patchwork/patch/1150367/
>
I see, this should all be settled now. Looking forward to v2.
Thanks,
Bjorn
>
> >
> > > ---
> > > arch/arm64/boot/dts/qcom/sc7180-idp.dts | 4 ++++
> > > arch/arm64/boot/dts/qcom/sc7180.dtsi | 27
> > +++++++++++++++++++++++++++
> > > 2 files changed, 31 insertions(+)
> > >
> > > diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> > b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> > > index 189254f..8a6a760 100644
> > > --- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> > > +++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> > > @@ -248,6 +248,10 @@
> > > status = "okay";
> > > };
> > >
> > > +&wifi {
> > > + status = "okay";
> >
> > Please conclude on the representation of the "skip-hyp-mem-assign" and
> > add it here, rather than in a subsequent patch - which implies that this
> > patch doesn't work on its own.
>
>
> Sure, I will update the next patchset.
>
>
> >
> > > +};
> > > +
> > > /* PINCTRL - additions to nodes defined in sc7180.dtsi */
> > >
> > > &qup_i2c2_default {
> > > diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> > b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> > > index 666e9b9..40c9971 100644
> > > --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> > > +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> > > @@ -42,6 +42,12 @@
> > > compatible = "qcom,cmd-db";
> > > no-map;
> > > };
> > > +
> > > + wlan_fw_mem: wlan_fw_region@93900000 {
> >
> > wlan_fw_mem: memory@93900000 {
> >
> > > + compatible = "removed-dma-pool";
> > > + no-map;
> > > + reg = <0 0x93900000 0 0x200000>;
> > > + };
> > > };
> > >
> > > cpus {
> > > @@ -1119,6 +1125,27 @@
> > > #clock-cells = <1>;
> > > };
> > > };
> > > +
> > > + wifi: wifi@18800000 {
> > > + status = "disabled";
> > > + compatible = "qcom,wcn3990-wifi";
> > > + reg = <0 0x18800000 0 0x800000>;
> > > + reg-names = "membase";
> > > + interrupts =
> > > + <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH /* CE0
> > */ >,
> > > + <GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH /* CE1
> > */ >,
> > > + <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH /* CE2
> > */ >,
> > > + <GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH /* CE3
> > */ >,
> > > + <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH /* CE4
> > */ >,
> > > + <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH /* CE5
> > */ >,
> > > + <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH /* CE6
> > */ >,
> > > + <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH /* CE7
> > */ >,
> > > + <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH /* CE8
> > */ >,
> > > + <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH /* CE9
> > */ >,
> > > + <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH /* CE10
> > */>,
> > > + <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH /* CE11
> > */>;
> > > + memory-region = <&wlan_fw_mem>;
> >
> > No iommus in sc7180?
> >
> > Regards,
> > Bjorn
> >
> > > + };
> > > };
> > >
> > > timer {
> > > --
> > > 2.7.4
> > >
> > >
> > > _______________________________________________
> > > linux-arm-kernel mailing list
> > > linux-arm-kernel@lists.infradead.org
> > > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2019-12-19 7:20 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <0101016ed018cde9-da3dc3e0-de6e-4b18-9add-bc6f88511ab2-000000@us-west-2.amazonses.com>
2019-12-11 7:20 ` [PATCH] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node Bjorn Andersson
2019-12-19 5:57 ` pillair
2019-12-19 7:20 ` Bjorn Andersson [this message]
2019-12-04 8:48 Rakesh Pillai
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191219072031.GH448416@yoga \
--to=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=pillair@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).