devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: <Codrin.Ciubotariu@microchip.com>
To: <linux-i2c@vger.kernel.org>, <devicetree@vger.kernel.org>,
	<linux-arm-kernel@lists.infradead.org>,
	<linux-kernel@vger.kernel.org>
Cc: <kamel.bouhara@bootlin.com>, <wsa@the-dreams.de>,
	<Nicolas.Ferre@microchip.com>, <alexandre.belloni@bootlin.com>,
	<Ludovic.Desroches@microchip.com>, <robh@kernel.org>,
	<Codrin.Ciubotariu@microchip.com>
Subject: [PATCH v2 2/6] i2c: at91: implement i2c bus recovery
Date: Fri, 3 Jan 2020 09:49:07 +0000	[thread overview]
Message-ID: <20200103094821.13185-3-codrin.ciubotariu@microchip.com> (raw)
In-Reply-To: <20200103094821.13185-1-codrin.ciubotariu@microchip.com>

From: Kamel Bouhara <kamel.bouhara@bootlin.com>

Implement i2c bus recovery when slaves devices might hold SDA low.
In this case re-assign SCL/SDA to gpios and issue 9 dummy clock pulses
until the slave release SDA.

Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
[codrin.ciubotariu@microchip.com: release gpios on error; move i2c_recover_bus]
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
---

Changes in v2:
 - called i2c_recover_bus() after an error occurs, if SDA is down;
 - release gpios if recovery information is incomplete;

 drivers/i2c/busses/i2c-at91-master.c | 79 ++++++++++++++++++++++++++++
 drivers/i2c/busses/i2c-at91.h        |  8 +++
 2 files changed, 87 insertions(+)

diff --git a/drivers/i2c/busses/i2c-at91-master.c b/drivers/i2c/busses/i2c-at91-master.c
index 7a862e00b475..c55e8ff35201 100644
--- a/drivers/i2c/busses/i2c-at91-master.c
+++ b/drivers/i2c/busses/i2c-at91-master.c
@@ -18,11 +18,13 @@
 #include <linux/dma-mapping.h>
 #include <linux/dmaengine.h>
 #include <linux/err.h>
+#include <linux/gpio/consumer.h>
 #include <linux/i2c.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
+#include <linux/pinctrl/consumer.h>
 #include <linux/platform_device.h>
 #include <linux/platform_data/dma-atmel.h>
 #include <linux/pm_runtime.h>
@@ -478,6 +480,7 @@ static int at91_do_twi_transfer(struct at91_twi_dev *dev)
 	unsigned long time_left;
 	bool has_unre_flag = dev->pdata->has_unre_flag;
 	bool has_alt_cmd = dev->pdata->has_alt_cmd;
+	struct i2c_bus_recovery_info *rinfo = &dev->rinfo;
 
 	/*
 	 * WARNING: the TXCOMP bit in the Status Register is NOT a clear on
@@ -637,6 +640,13 @@ static int at91_do_twi_transfer(struct at91_twi_dev *dev)
 		at91_twi_write(dev, AT91_TWI_CR,
 			       AT91_TWI_THRCLR | AT91_TWI_LOCKCLR);
 	}
+
+	if (rinfo->get_sda && !(rinfo->get_sda(&dev->adapter))) {
+		dev_dbg(dev->dev,
+			"SDA is down; clear bus using gpio\n");
+		i2c_recover_bus(&dev->adapter);
+	}
+
 	return ret;
 }
 
@@ -806,6 +816,71 @@ static int at91_twi_configure_dma(struct at91_twi_dev *dev, u32 phy_addr)
 	return ret;
 }
 
+static void at91_prepare_twi_recovery(struct i2c_adapter *adap)
+{
+	struct at91_twi_dev *dev = i2c_get_adapdata(adap);
+
+	pinctrl_select_state(dev->pinctrl, dev->pinctrl_pins_gpio);
+}
+
+static void at91_unprepare_twi_recovery(struct i2c_adapter *adap)
+{
+	struct at91_twi_dev *dev = i2c_get_adapdata(adap);
+
+	pinctrl_select_state(dev->pinctrl, dev->pinctrl_pins_default);
+}
+
+static int at91_init_twi_recovery_info(struct platform_device *pdev,
+				       struct at91_twi_dev *dev)
+{
+	struct i2c_bus_recovery_info *rinfo = &dev->rinfo;
+
+	dev->pinctrl = devm_pinctrl_get(&pdev->dev);
+	if (!dev->pinctrl || IS_ERR(dev->pinctrl)) {
+		dev_info(dev->dev, "can't get pinctrl, bus recovery not supported\n");
+		return PTR_ERR(dev->pinctrl);
+	}
+
+	dev->pinctrl_pins_default = pinctrl_lookup_state(dev->pinctrl,
+							 PINCTRL_STATE_DEFAULT);
+	dev->pinctrl_pins_gpio = pinctrl_lookup_state(dev->pinctrl,
+						      "gpio");
+	rinfo->sda_gpiod = devm_gpiod_get(&pdev->dev, "sda", GPIOD_IN);
+	if (PTR_ERR(rinfo->sda_gpiod) == -EPROBE_DEFER)
+		return -EPROBE_DEFER;
+
+	rinfo->scl_gpiod = devm_gpiod_get(&pdev->dev, "scl",
+					  GPIOD_OUT_HIGH_OPEN_DRAIN);
+	if (PTR_ERR(rinfo->scl_gpiod) == -EPROBE_DEFER)
+		return -EPROBE_DEFER;
+
+	if (IS_ERR(rinfo->sda_gpiod) ||
+	    IS_ERR(rinfo->scl_gpiod) ||
+	    IS_ERR(dev->pinctrl_pins_default) ||
+	    IS_ERR(dev->pinctrl_pins_gpio)) {
+		dev_info(&pdev->dev, "recovery information incomplete\n");
+		if (!IS_ERR(rinfo->sda_gpiod)) {
+			gpiod_put(rinfo->sda_gpiod);
+			rinfo->sda_gpiod = NULL;
+		}
+		if (!IS_ERR(rinfo->scl_gpiod)) {
+			gpiod_put(rinfo->scl_gpiod);
+			rinfo->scl_gpiod = NULL;
+		}
+		return -EINVAL;
+	}
+
+	dev_info(&pdev->dev, "using scl%s for recovery\n",
+		 rinfo->sda_gpiod ? ",sda" : "");
+
+	rinfo->prepare_recovery = at91_prepare_twi_recovery;
+	rinfo->unprepare_recovery = at91_unprepare_twi_recovery;
+	rinfo->recover_bus = i2c_generic_scl_recovery;
+	dev->adapter.bus_recovery_info = rinfo;
+
+	return 0;
+}
+
 int at91_twi_probe_master(struct platform_device *pdev,
 			  u32 phy_addr, struct at91_twi_dev *dev)
 {
@@ -838,6 +913,10 @@ int at91_twi_probe_master(struct platform_device *pdev,
 						     "i2c-analog-filter");
 	at91_calc_twi_clock(dev);
 
+	rc = at91_init_twi_recovery_info(pdev, dev);
+	if (rc == -EPROBE_DEFER)
+		return rc;
+
 	dev->adapter.algo = &at91_twi_algorithm;
 	dev->adapter.quirks = &at91_twi_quirks;
 
diff --git a/drivers/i2c/busses/i2c-at91.h b/drivers/i2c/busses/i2c-at91.h
index 977a67bc0f88..eb335b71e775 100644
--- a/drivers/i2c/busses/i2c-at91.h
+++ b/drivers/i2c/busses/i2c-at91.h
@@ -151,6 +151,10 @@ struct at91_twi_dev {
 	u32 fifo_size;
 	struct at91_twi_dma dma;
 	bool slave_detected;
+	struct i2c_bus_recovery_info rinfo;
+	struct pinctrl *pinctrl;
+	struct pinctrl_state *pinctrl_pins_default;
+	struct pinctrl_state *pinctrl_pins_gpio;
 #ifdef CONFIG_I2C_AT91_SLAVE_EXPERIMENTAL
 	unsigned smr;
 	struct i2c_client *slave;
@@ -171,6 +175,10 @@ void at91_init_twi_bus_master(struct at91_twi_dev *dev);
 int at91_twi_probe_master(struct platform_device *pdev, u32 phy_addr,
 			  struct at91_twi_dev *dev);
 
+void at91_twi_prepare_recovery(struct i2c_adapter *adap);
+void at91_twi_unprepare_recovery(struct i2c_adapter *adap);
+void at91_twi_init_recovery_info(struct at91_twi_dev *dev);
+
 #ifdef CONFIG_I2C_AT91_SLAVE_EXPERIMENTAL
 void at91_init_twi_bus_slave(struct at91_twi_dev *dev);
 int at91_twi_probe_slave(struct platform_device *pdev, u32 phy_addr,
-- 
2.20.1

  parent reply	other threads:[~2020-01-03  9:49 UTC|newest]

Thread overview: 17+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-01-03  9:49 [PATCH v2 0/6] i2c bus recovery for Microchip SoCs Codrin.Ciubotariu
2020-01-03  9:49 ` [PATCH v2 1/6] dt-bindings: i2c: at91: document optional bus recovery properties Codrin.Ciubotariu
2020-01-03 22:29   ` Rob Herring
2020-01-06 16:34     ` Codrin.Ciubotariu
2020-01-03  9:49 ` [PATCH v2 3/6] i2c: at91: Send bus clear command if SCL is down Codrin.Ciubotariu
2020-01-09  7:47   ` Ludovic Desroches
2020-01-09 10:58     ` Codrin.Ciubotariu
2020-01-09 11:05   ` Russell King - ARM Linux admin
2020-01-09 13:29     ` Codrin.Ciubotariu
2020-01-03  9:49 ` Codrin.Ciubotariu [this message]
2020-01-09  7:48   ` [PATCH v2 2/6] i2c: at91: implement i2c bus recovery Ludovic Desroches
2020-01-09 10:54     ` Codrin.Ciubotariu
2020-01-03  9:49 ` [PATCH v2 4/6] ARM: at91/dt: sama5d3: add i2c gpio pinctrl Codrin.Ciubotariu
2020-01-04 22:39   ` Peter Rosin
2020-01-06 16:58     ` Codrin.Ciubotariu
2020-01-03  9:49 ` [PATCH v2 5/6] ARM: at91/dt: sama5d4: " Codrin.Ciubotariu
2020-01-03  9:49 ` [PATCH v2 6/6] ARM: at91/dt: sama5d2: " Codrin.Ciubotariu

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20200103094821.13185-3-codrin.ciubotariu@microchip.com \
    --to=codrin.ciubotariu@microchip.com \
    --cc=Ludovic.Desroches@microchip.com \
    --cc=Nicolas.Ferre@microchip.com \
    --cc=alexandre.belloni@bootlin.com \
    --cc=devicetree@vger.kernel.org \
    --cc=kamel.bouhara@bootlin.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-i2c@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=robh@kernel.org \
    --cc=wsa@the-dreams.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).