[PATCH AUTOSEL 4.14 02/32] dt-bindings: reset: meson8b: fix duplicate reset IDs

[PATCH AUTOSEL 4.14 02/32] dt-bindings: reset: meson8b: fix duplicate reset IDs

[Sasha Levin]

From: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

[ Upstream commit 4881873f4cc1460f63d85fa81363d56be328ccdc ]

According to the public S805 datasheet the RESET2 register uses the
following bits for the PIC_DC, PSC and NAND reset lines:
- PIC_DC is at bit 3 (meaning: RESET_VD_RMEM + 3)
- PSC is at bit 4 (meaning: RESET_VD_RMEM + 4)
- NAND is at bit 5 (meaning: RESET_VD_RMEM + 4)

Update the reset IDs of these three reset lines so they don't conflict
with PIC_DC and map to the actual hardware reset lines.

Fixes: 79795e20a184eb ("dt-bindings: reset: Add bindings for the Meson SoC Reset Controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 include/dt-bindings/reset/amlogic,meson8b-reset.h | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/include/dt-bindings/reset/amlogic,meson8b-reset.h b/include/dt-bindings/reset/amlogic,meson8b-reset.h
index 614aff2c7affe..a03e86fe2c570 100644
--- a/include/dt-bindings/reset/amlogic,meson8b-reset.h
+++ b/include/dt-bindings/reset/amlogic,meson8b-reset.h
@@ -95,9 +95,9 @@
 #define RESET_VD_RMEM			64
 #define RESET_AUDIN			65
 #define RESET_DBLK			66
-#define RESET_PIC_DC			66
-#define RESET_PSC			66
-#define RESET_NAND			66
+#define RESET_PIC_DC			67
+#define RESET_PSC			68
+#define RESET_NAND			69
 #define RESET_GE2D			70
 #define RESET_PARSER_REG		71
 #define RESET_PARSER_FETCH		72
-- 
2.20.1

[PATCH AUTOSEL 4.14 03/32] ARM: dts: sun8i: a83t: Correct USB3503 GPIOs polarity

[Sasha Levin]

From: Marek Szyprowski <m.szyprowski@samsung.com>

[ Upstream commit 1c226017d3ec93547b58082bdf778d9db7401c95 ]

Current USB3503 driver ignores GPIO polarity and always operates as if the
GPIO lines were flagged as ACTIVE_HIGH. Fix the polarity for the existing
USB3503 chip applications to match the chip specification and common
convention for naming the pins. The only pin, which has to be ACTIVE_LOW
is the reset pin. The remaining are ACTIVE_HIGH. This change allows later
to fix the USB3503 driver to properly use generic GPIO bindings and read
polarity from DT.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
index 716a205c6dbbe..1fed3231f5c18 100644
--- a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
+++ b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
@@ -90,7 +90,7 @@
 		initial-mode = <1>; /* initialize in HUB mode */
 		disabled-ports = <1>;
 		intn-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
-		reset-gpios = <&pio 4 16 GPIO_ACTIVE_HIGH>; /* PE16 */
+		reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */
 		connect-gpios = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */
 		refclk-frequency = <19200000>;
 	};
-- 
2.20.1

[PATCH AUTOSEL 4.14 04/32] ARM: dts: beagle-x15-common: Model 5V0 regulator

[Sasha Levin]

From: Kishon Vijay Abraham I <kishon@ti.com>

[ Upstream commit e17e7c498d4f734df93c300441e100818ed58168 ]

On am57xx-beagle-x15, 5V0 is connected to P16, P17, P18 and P19
connectors. On am57xx-evm, 5V0 regulator is used to get 3V6 regulator
which is connected to the COMQ port. Model 5V0 regulator here in order
for it to be used in am57xx-evm to model 3V6 regulator.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../boot/dts/am57xx-beagle-x15-common.dtsi    | 21 +++++++++++++++++++
 1 file changed, 21 insertions(+)

diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
index 49aeecd312b4b..d578a9f7e1a0e 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
+++ b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
@@ -32,6 +32,27 @@
 		reg = <0x0 0x80000000 0x0 0x80000000>;
 	};
 
+	main_12v0: fixedregulator-main_12v0 {
+		/* main supply */
+		compatible = "regulator-fixed";
+		regulator-name = "main_12v0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	evm_5v0: fixedregulator-evm_5v0 {
+		/* Output of TPS54531D */
+		compatible = "regulator-fixed";
+		regulator-name = "evm_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&main_12v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
 	vdd_3v3: fixedregulator-vdd_3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_3v3";
-- 
2.20.1