[PATCH v2 7/9] tty: serial: fsl_lpuart: add LS1028A earlycon support

[Michael Walle <michael@walle.cc>]

Add a early_console_setup() for the LS1028A SoC with 32bit, little
endian access. If the bootloader does a fixup of the clock-frequency
node the baudrate divisor register will automatically be set.

Signed-off-by: Michael Walle <michael@walle.cc>
---
 drivers/tty/serial/fsl_lpuart.c | 51 +++++++++++++++++++++++++++------
 1 file changed, 43 insertions(+), 8 deletions(-)

diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c
index d5a67e02f06a..e8e5c60e5b71 100644
--- a/drivers/tty/serial/fsl_lpuart.c
+++ b/drivers/tty/serial/fsl_lpuart.c
@@ -1841,11 +1841,12 @@ lpuart_set_termios(struct uart_port *port, struct ktermios *termios,
 	spin_unlock_irqrestore(&sport->port.lock, flags);
 }
 
-static void
-lpuart32_serial_setbrg(struct lpuart_port *sport, unsigned int baudrate)
+static void __lpuart32_serial_setbrg(struct uart_port *port,
+				     unsigned int baudrate, bool use_rx_dma,
+				     bool use_tx_dma)
 {
 	u32 sbr, osr, baud_diff, tmp_osr, tmp_sbr, tmp_diff, tmp;
-	u32 clk = sport->port.uartclk;
+	u32 clk = port->uartclk;
 
 	/*
 	 * The idea is to use the best OSR (over-sampling rate) possible.
@@ -1891,10 +1892,10 @@ lpuart32_serial_setbrg(struct lpuart_port *sport, unsigned int baudrate)
 
 	/* handle buadrate outside acceptable rate */
 	if (baud_diff > ((baudrate / 100) * 3))
-		dev_warn(sport->port.dev,
+		dev_warn(port->dev,
 			 "unacceptable baud rate difference of more than 3%%\n");
 
-	tmp = lpuart32_read(&sport->port, UARTBAUD);
+	tmp = lpuart32_read(port, UARTBAUD);
 
 	if ((osr > 3) && (osr < 8))
 		tmp |= UARTBAUD_BOTHEDGE;
@@ -1905,14 +1906,23 @@ lpuart32_serial_setbrg(struct lpuart_port *sport, unsigned int baudrate)
 	tmp &= ~UARTBAUD_SBR_MASK;
 	tmp |= sbr & UARTBAUD_SBR_MASK;
 
-	if (!sport->lpuart_dma_rx_use)
+	if (!use_rx_dma)
 		tmp &= ~UARTBAUD_RDMAE;
-	if (!sport->lpuart_dma_tx_use)
+	if (!use_tx_dma)
 		tmp &= ~UARTBAUD_TDMAE;
 
-	lpuart32_write(&sport->port, tmp, UARTBAUD);
+	lpuart32_write(port, tmp, UARTBAUD);
+}
+
+static void lpuart32_serial_setbrg(struct lpuart_port *sport,
+				   unsigned int baudrate)
+{
+	__lpuart32_serial_setbrg(&sport->port, baudrate,
+				 sport->lpuart_dma_rx_use,
+				 sport->lpuart_dma_tx_use);
 }
 
+
 static void
 lpuart32_set_termios(struct uart_port *port, struct ktermios *termios,
 		   struct ktermios *old)
@@ -2406,6 +2416,30 @@ static int __init lpuart32_early_console_setup(struct earlycon_device *device,
 	return 0;
 }
 
+static int __init ls1028a_early_console_setup(struct earlycon_device *device,
+					      const char *opt)
+{
+	u32 cr;
+
+	if (!device->port.membase)
+		return -ENODEV;
+
+	device->port.iotype = UPIO_MEM32;
+	device->con->write = lpuart32_early_write;
+
+	/* set the baudrate */
+	if (device->port.uartclk && device->baud)
+		__lpuart32_serial_setbrg(&device->port, device->baud,
+					 false, false);
+
+	/* enable transmitter */
+	cr = lpuart32_read(&device->port, UARTCTRL);
+	cr |= UARTCTRL_TE;
+	lpuart32_write(&device->port, cr, UARTCTRL);
+
+	return 0;
+}
+
 static int __init lpuart32_imx_early_console_setup(struct earlycon_device *device,
 						   const char *opt)
 {
@@ -2420,6 +2454,7 @@ static int __init lpuart32_imx_early_console_setup(struct earlycon_device *devic
 }
 OF_EARLYCON_DECLARE(lpuart, "fsl,vf610-lpuart", lpuart_early_console_setup);
 OF_EARLYCON_DECLARE(lpuart32, "fsl,ls1021a-lpuart", lpuart32_early_console_setup);
+OF_EARLYCON_DECLARE(lpuart32, "fsl,ls1028a-lpuart", ls1028a_early_console_setup);
 OF_EARLYCON_DECLARE(lpuart32, "fsl,imx7ulp-lpuart", lpuart32_imx_early_console_setup);
 EARLYCON_DECLARE(lpuart, lpuart_early_console_setup);
 EARLYCON_DECLARE(lpuart32, lpuart32_early_console_setup);
-- 
2.20.1