[PATCH devicetree 0/2] Remainder for "[PATCH v5 00/12] NXP DSPI bugfixes and support for LS1028A"

[PATCH devicetree 0/2] Remainder for "[PATCH v5 00/12] NXP DSPI bugfixes and support for LS1028A"

[Vladimir Oltean]

From: Vladimir Oltean <vladimir.oltean@nxp.com>

The series with DSPI support for LS1028A was merged by Mark Brown in his
linux-spi tree here:

https://www.spinics.net/lists/linux-spi/msg20842.html

These remaining 2 patches from that series apply on top of Michael
Walle's basic device tree support patch:

https://patchwork.kernel.org/patch/11389157/#23165893

Vladimir Oltean (2):
  arm64: dts: ls1028a: Specify the DMA channels for the DSPI controllers
  arm64: dts: ls1028a-rdb: Add a spidev node for the mikroBUS

 arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts | 14 ++++++++++++++
 arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi    |  6 ++++++
 2 files changed, 20 insertions(+)

-- 
2.17.1

[PATCH devicetree 1/2] arm64: dts: ls1028a: Specify the DMA channels for the DSPI controllers

[Vladimir Oltean]

From: Vladimir Oltean <vladimir.oltean@nxp.com>

LS1028A has a functional connection to the eDMA module. Even if the
spi-fsl-dspi.c driver is not using DMA for LS1028A now, define the slots
in the DMAMUX for connecting the eDMA channels to the 3 DSPI
controllers.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
---
 arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
index 515e0a1b934f..18155273a46e 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
@@ -298,6 +298,8 @@
 			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
 			clock-names = "dspi";
 			clocks = <&clockgen 4 1>;
+			dmas = <&edma0 0 62>, <&edma0 0 60>;
+			dma-names = "tx", "rx";
 			spi-num-chipselects = <4>;
 			little-endian;
 			status = "disabled";
@@ -311,6 +313,8 @@
 			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
 			clock-names = "dspi";
 			clocks = <&clockgen 4 1>;
+			dmas = <&edma0 0 58>, <&edma0 0 56>;
+			dma-names = "tx", "rx";
 			spi-num-chipselects = <4>;
 			little-endian;
 			status = "disabled";
@@ -324,6 +328,8 @@
 			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
 			clock-names = "dspi";
 			clocks = <&clockgen 4 1>;
+			dmas = <&edma0 0 54>, <&edma0 0 2>;
+			dma-names = "tx", "rx";
 			spi-num-chipselects = <3>;
 			little-endian;
 			status = "disabled";
-- 
2.17.1

[PATCH devicetree 2/2] arm64: dts: ls1028a-rdb: Add a spidev node for the mikroBUS

[Vladimir Oltean]

From: Vladimir Oltean <vladimir.oltean@nxp.com>

For debugging, it is useful to have access to the DSPI controller
signals. On the reference design board, these are exported to either the
mikroBUS1 or mikroBUS2 connector (according to the CPLD register
BRDCFG3[SPI3]).

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
---
 arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
index 6d05b76c2c7a..0d27b5667b8c 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
@@ -83,6 +83,20 @@
 	};
 };
 
+&dspi2 {
+	bus-num = <2>;
+	status = "okay";
+
+	/* mikroBUS1 */
+	spidev@0 {
+		compatible = "rohm,dh2228fv";
+		spi-max-frequency = <20000000>;
+		fsl,spi-cs-sck-delay = <100>;
+		fsl,spi-sck-cs-delay = <100>;
+		reg = <0>;
+	};
+};
+
 &esdhc {
 	sd-uhs-sdr104;
 	sd-uhs-sdr50;
-- 
2.17.1