From: Leon Romanovsky <leon@kernel.org>
To: Robert Marko <robert.marko@sartura.hr>
Cc: andrew@lunn.ch, f.fainelli@gmail.com, hkallweit1@gmail.com,
linux@armlinux.org.uk, linux-kernel@vger.kernel.org,
netdev@vger.kernel.org, agross@kernel.org,
bjorn.andersson@linaro.org, robh+dt@kernel.org,
mark.rutland@arm.com, linux-arm-msm@vger.kernel.org,
devicetree@vger.kernel.org,
Christian Lamparter <chunkeey@gmail.com>,
Luka Perkov <luka.perkov@sartura.hr>
Subject: Re: [PATCH v3 1/3] net: phy: mdio: add IPQ40xx MDIO driver
Date: Thu, 16 Apr 2020 10:28:01 +0300 [thread overview]
Message-ID: <20200416072801.GG1309273@unreal> (raw)
In-Reply-To: <20200415150244.2737206-1-robert.marko@sartura.hr>
On Wed, Apr 15, 2020 at 05:02:43PM +0200, Robert Marko wrote:
> This patch adds the driver for the MDIO interface
> inside of Qualcomm IPQ40xx series SoC-s.
>
> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
> Signed-off-by: Robert Marko <robert.marko@sartura.hr>
> Cc: Luka Perkov <luka.perkov@sartura.hr>
> ---
> Changes from v2 to v3:
> * Rename registers
> * Remove unnecessary variable initialisations
> * Switch to readl_poll_timeout() instead of custom solution
> * Drop unused header
>
> Changes from v1 to v2:
> * Remove magic default value
> * Remove lockdep_assert_held
> * Add C45 check
> * Simplify the driver
> * Drop device and mii_bus structs from private struct
> * Use devm_mdiobus_alloc_size()
>
> drivers/net/phy/Kconfig | 7 ++
> drivers/net/phy/Makefile | 1 +
> drivers/net/phy/mdio-ipq40xx.c | 160 +++++++++++++++++++++++++++++++++
> 3 files changed, 168 insertions(+)
> create mode 100644 drivers/net/phy/mdio-ipq40xx.c
>
> diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
> index 3fa33d27eeba..23bb5db033e3 100644
> --- a/drivers/net/phy/Kconfig
> +++ b/drivers/net/phy/Kconfig
> @@ -157,6 +157,13 @@ config MDIO_I2C
>
> This is library mode.
>
> +config MDIO_IPQ40XX
> + tristate "Qualcomm IPQ40xx MDIO interface"
> + depends on HAS_IOMEM && OF_MDIO
> + help
> + This driver supports the MDIO interface found in Qualcomm
> + IPQ40xx series Soc-s.
> +
> config MDIO_IPQ8064
> tristate "Qualcomm IPQ8064 MDIO interface support"
> depends on HAS_IOMEM && OF_MDIO
> diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
> index 2f5c7093a65b..36aafc6128c4 100644
> --- a/drivers/net/phy/Makefile
> +++ b/drivers/net/phy/Makefile
> @@ -37,6 +37,7 @@ obj-$(CONFIG_MDIO_CAVIUM) += mdio-cavium.o
> obj-$(CONFIG_MDIO_GPIO) += mdio-gpio.o
> obj-$(CONFIG_MDIO_HISI_FEMAC) += mdio-hisi-femac.o
> obj-$(CONFIG_MDIO_I2C) += mdio-i2c.o
> +obj-$(CONFIG_MDIO_IPQ40XX) += mdio-ipq40xx.o
> obj-$(CONFIG_MDIO_IPQ8064) += mdio-ipq8064.o
> obj-$(CONFIG_MDIO_MOXART) += mdio-moxart.o
> obj-$(CONFIG_MDIO_MSCC_MIIM) += mdio-mscc-miim.o
> diff --git a/drivers/net/phy/mdio-ipq40xx.c b/drivers/net/phy/mdio-ipq40xx.c
> new file mode 100644
> index 000000000000..acf1230341bd
> --- /dev/null
> +++ b/drivers/net/phy/mdio-ipq40xx.c
> @@ -0,0 +1,160 @@
> +// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
> +/* Copyright (c) 2015, The Linux Foundation. All rights reserved. */
> +/* Copyright (c) 2020 Sartura Ltd. */
> +
> +#include <linux/delay.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/io.h>
> +#include <linux/iopoll.h>
> +#include <linux/of_address.h>
> +#include <linux/of_mdio.h>
> +#include <linux/phy.h>
> +#include <linux/platform_device.h>
> +
> +#define MDIO_ADDR_REG 0x44
> +#define MDIO_DATA_WRITE_REG 0x48
> +#define MDIO_DATA_READ_REG 0x4c
> +#define MDIO_CMD_REG 0x50
> +#define MDIO_CMD_ACCESS_BUSY BIT(16)
> +#define MDIO_CMD_ACCESS_START BIT(8)
> +#define MDIO_CMD_ACCESS_CODE_READ 0
> +#define MDIO_CMD_ACCESS_CODE_WRITE 1
> +
> +#define IPQ40XX_MDIO_TIMEOUT 10000
> +#define IPQ40XX_MDIO_SLEEP 10
> +
> +struct ipq40xx_mdio_data {
> + void __iomem *membase;
> +};
> +
> +static int ipq40xx_mdio_wait_busy(struct mii_bus *bus)
> +{
> + struct ipq40xx_mdio_data *priv = bus->priv;
> + unsigned int busy;
> +
> + return readl_poll_timeout(priv->membase + MDIO_CMD_REG, busy,
> + (busy & MDIO_CMD_ACCESS_BUSY) == 0,
> + IPQ40XX_MDIO_SLEEP, IPQ40XX_MDIO_TIMEOUT);
> +}
> +
> +static int ipq40xx_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
> +{
> + struct ipq40xx_mdio_data *priv = bus->priv;
> + unsigned int cmd;
> +
> + /* Reject clause 45 */
> + if (regnum & MII_ADDR_C45)
> + return -EOPNOTSUPP;
> +
> + if (ipq40xx_mdio_wait_busy(bus))
> + return -ETIMEDOUT;
> +
> + /* issue the phy address and reg */
> + writel((mii_id << 8) | regnum, priv->membase + MDIO_ADDR_REG);
> +
> + cmd = MDIO_CMD_ACCESS_START | MDIO_CMD_ACCESS_CODE_READ;
> +
> + /* issue read command */
> + writel(cmd, priv->membase + MDIO_CMD_REG);
> +
> + /* Wait read complete */
> + if (ipq40xx_mdio_wait_busy(bus))
> + return -ETIMEDOUT;
> +
> + /* Read and return data */
> + return readl(priv->membase + MDIO_DATA_READ_REG);
> +}
> +
> +static int ipq40xx_mdio_write(struct mii_bus *bus, int mii_id, int regnum,
> + u16 value)
> +{
> + struct ipq40xx_mdio_data *priv = bus->priv;
> + unsigned int cmd;
> +
> + /* Reject clause 45 */
> + if (regnum & MII_ADDR_C45)
> + return -EOPNOTSUPP;
> +
> + if (ipq40xx_mdio_wait_busy(bus))
> + return -ETIMEDOUT;
> +
> + /* issue the phy address and reg */
> + writel((mii_id << 8) | regnum, priv->membase + MDIO_ADDR_REG);
> +
> + /* issue write data */
> + writel(value, priv->membase + MDIO_DATA_WRITE_REG);
> +
> + cmd = MDIO_CMD_ACCESS_START | MDIO_CMD_ACCESS_CODE_WRITE;
> + /* issue write command */
> + writel(cmd, priv->membase + MDIO_CMD_REG);
> +
> + /* Wait write complete */
> + if (ipq40xx_mdio_wait_busy(bus))
> + return -ETIMEDOUT;
> +
> + return 0;
> +}
> +
> +static int ipq40xx_mdio_probe(struct platform_device *pdev)
> +{
> + struct ipq40xx_mdio_data *priv;
> + struct mii_bus *bus;
> + int ret;
> +
> + bus = devm_mdiobus_alloc_size(&pdev->dev, sizeof(*priv));
> + if (!bus)
> + return -ENOMEM;
> +
> + priv = bus->priv;
> +
> + priv->membase = devm_platform_ioremap_resource(pdev, 0);
> + if (IS_ERR(priv->membase))
> + return PTR_ERR(priv->membase);
> +
> + bus->name = "ipq40xx_mdio";
> + bus->read = ipq40xx_mdio_read;
> + bus->write = ipq40xx_mdio_write;
> + bus->parent = &pdev->dev;
> + snprintf(bus->id, MII_BUS_ID_SIZE, "%s%d", pdev->name, pdev->id);
> +
> + ret = of_mdiobus_register(bus, pdev->dev.of_node);
> + if (ret) {
> + dev_err(&pdev->dev, "Cannot register MDIO bus!\n");
> + return ret;
> + }
> +
> + platform_set_drvdata(pdev, bus);
> +
> + return 0;
> +}
> +
> +static int ipq40xx_mdio_remove(struct platform_device *pdev)
> +{
> + struct mii_bus *bus = platform_get_drvdata(pdev);
> +
> + mdiobus_unregister(bus);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id ipq40xx_mdio_dt_ids[] = {
> + { .compatible = "qcom,ipq40xx-mdio" },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, ipq40xx_mdio_dt_ids);
> +
> +static struct platform_driver ipq40xx_mdio_driver = {
> + .probe = ipq40xx_mdio_probe,
> + .remove = ipq40xx_mdio_remove,
> + .driver = {
> + .name = "ipq40xx-mdio",
> + .of_match_table = ipq40xx_mdio_dt_ids,
> + },
> +};
> +
> +module_platform_driver(ipq40xx_mdio_driver);
> +
> +MODULE_DESCRIPTION("IPQ40XX MDIO interface driver");
> +MODULE_AUTHOR("Qualcomm Atheros");
Strictly saying, but author can't be company.
> +MODULE_LICENSE("Dual BSD/GPL");
> --
> 2.26.0
>
prev parent reply other threads:[~2020-04-16 7:28 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-04-15 15:02 [PATCH v3 1/3] net: phy: mdio: add IPQ40xx MDIO driver Robert Marko
2020-04-15 15:02 ` [PATCH v3 2/3] dt-bindings: add Qualcomm IPQ4019 MDIO bindings Robert Marko
2020-04-15 23:49 ` Andrew Lunn
2020-04-15 23:55 ` Florian Fainelli
2020-04-16 8:43 ` Robert Marko
2020-04-28 15:09 ` Rob Herring
2020-04-28 16:40 ` Robert Marko
2020-04-15 15:02 ` [PATCH v3 3/3] ARM: dts: qcom: ipq4019: add MDIO node Robert Marko
2020-04-15 23:51 ` Andrew Lunn
2020-04-15 23:56 ` Florian Fainelli
2020-04-15 23:48 ` [PATCH v3 1/3] net: phy: mdio: add IPQ40xx MDIO driver Andrew Lunn
2020-04-16 8:43 ` Robert Marko
2020-04-15 23:57 ` Florian Fainelli
2020-04-16 7:28 ` Leon Romanovsky [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200416072801.GG1309273@unreal \
--to=leon@kernel.org \
--cc=agross@kernel.org \
--cc=andrew@lunn.ch \
--cc=bjorn.andersson@linaro.org \
--cc=chunkeey@gmail.com \
--cc=devicetree@vger.kernel.org \
--cc=f.fainelli@gmail.com \
--cc=hkallweit1@gmail.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=luka.perkov@sartura.hr \
--cc=mark.rutland@arm.com \
--cc=netdev@vger.kernel.org \
--cc=robert.marko@sartura.hr \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).