From: Erwan Le Ray <erwan.leray@st.com>
To: Maxime Coquelin <mcoquelin.stm32@gmail.com>,
Alexandre Torgue <alexandre.torgue@st.com>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>
Cc: <linux-stm32@st-md-mailman.stormreply.com>,
<linux-arm-kernel@lists.infradead.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
Erwan Le Ray <erwan.leray@st.com>,
Fabrice Gasnier <fabrice.gasnier@st.com>
Subject: [PATCH 1/5] ARM: dts: stm32: add usart2, usart3 and uart7 pins in stm32mp15-pinctrl
Date: Thu, 28 May 2020 09:40:25 +0200 [thread overview]
Message-ID: <20200528074029.24962-2-erwan.leray@st.com> (raw)
In-Reply-To: <20200528074029.24962-1-erwan.leray@st.com>
Adds usart2_pins_c, usart3_pins_b, usart3_pins_c and uart7_pins_c pins
configurations in stm32mp15-pinctrl.
- usart2_pins_c pins are connected to Bluetooth chip on dk2 board.
- usart3_pins_b pins are connected to GPIO expansion connector on evx board.
- usart3_pins_c pins are connected to GPIO expansion connector on dkx board.
- uart7_pins_c pins are connected to Arduino Uno connector on dkx board.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
diff --git a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
index fb98a66977fe..99e399e4e4c3 100644
--- a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
@@ -1658,6 +1658,36 @@
};
};
+ uart7_pins_c: uart7-1 {
+ pins1 {
+ pinmux = <STM32_PINMUX('E', 8, AF7)>; /* USART7_TX */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('E', 7, AF7)>; /* USART7_RX */
+ bias-disable;
+ };
+ };
+
+ uart7_idle_pins_c: uart7-idle-1 {
+ pins1 {
+ pinmux = <STM32_PINMUX('E', 8, ANALOG)>; /* USART7_TX */
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('E', 7, AF7)>; /* USART7_RX */
+ bias-disable;
+ };
+ };
+
+ uart7_sleep_pins_c: uart7-sleep-1 {
+ pins {
+ pinmux = <STM32_PINMUX('E', 8, ANALOG)>, /* USART7_TX */
+ <STM32_PINMUX('E', 7, ANALOG)>; /* USART7_RX */
+ };
+ };
+
uart8_pins_a: uart8-0 {
pins1 {
pinmux = <STM32_PINMUX('E', 1, AF8)>; /* UART8_TX */
@@ -1719,6 +1749,42 @@
};
};
+ usart2_pins_c: usart2-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('D', 5, AF7)>, /* USART2_TX */
+ <STM32_PINMUX('D', 4, AF7)>; /* USART2_RTS */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <3>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('D', 6, AF7)>, /* USART2_RX */
+ <STM32_PINMUX('D', 3, AF7)>; /* USART2_CTS_NSS */
+ bias-disable;
+ };
+ };
+
+ usart2_idle_pins_c: usart2-idle-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('D', 5, ANALOG)>, /* USART2_TX */
+ <STM32_PINMUX('D', 4, ANALOG)>, /* USART2_RTS */
+ <STM32_PINMUX('D', 3, ANALOG)>; /* USART2_CTS_NSS */
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('D', 6, AF7)>; /* USART2_RX */
+ bias-disable;
+ };
+ };
+
+ usart2_sleep_pins_c: usart2-sleep-0 {
+ pins {
+ pinmux = <STM32_PINMUX('D', 5, ANALOG)>, /* USART2_TX */
+ <STM32_PINMUX('D', 4, ANALOG)>, /* USART2_RTS */
+ <STM32_PINMUX('D', 6, ANALOG)>, /* USART2_RX */
+ <STM32_PINMUX('D', 3, ANALOG)>; /* USART2_CTS_NSS */
+ };
+ };
+
usart3_pins_a: usart3-0 {
pins1 {
pinmux = <STM32_PINMUX('B', 10, AF7)>; /* USART3_TX */
@@ -1732,6 +1798,78 @@
};
};
+ usart3_pins_b: usart3-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('B', 10, AF7)>, /* USART3_TX */
+ <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('B', 12, AF8)>, /* USART3_RX */
+ <STM32_PINMUX('I', 10, AF8)>; /* USART3_CTS_NSS */
+ bias-disable;
+ };
+ };
+
+ usart3_idle_pins_b: usart3-idle-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+ <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
+ <STM32_PINMUX('I', 10, ANALOG)>; /* USART3_CTS_NSS */
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('B', 12, AF8)>; /* USART3_RX */
+ bias-disable;
+ };
+ };
+
+ usart3_sleep_pins_b: usart3-sleep-0 {
+ pins {
+ pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+ <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
+ <STM32_PINMUX('I', 10, ANALOG)>, /* USART3_CTS_NSS */
+ <STM32_PINMUX('B', 12, ANALOG)>; /* USART3_RX */
+ };
+ };
+
+ usart3_pins_c: usart3-1 {
+ pins1 {
+ pinmux = <STM32_PINMUX('B', 10, AF7)>, /* USART3_TX */
+ <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('B', 12, AF8)>, /* USART3_RX */
+ <STM32_PINMUX('B', 13, AF7)>; /* USART3_CTS_NSS */
+ bias-disable;
+ };
+ };
+
+ usart3_idle_pins_c: usart3-idle-1 {
+ pins1 {
+ pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+ <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
+ <STM32_PINMUX('B', 13, ANALOG)>; /* USART3_CTS_NSS */
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('B', 12, AF8)>; /* USART3_RX */
+ bias-disable;
+ };
+ };
+
+ usart3_sleep_pins_c: usart3-sleep-1 {
+ pins {
+ pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+ <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
+ <STM32_PINMUX('B', 13, ANALOG)>, /* USART3_CTS_NSS */
+ <STM32_PINMUX('B', 12, ANALOG)>; /* USART3_RX */
+ };
+ };
+
usbotg_hs_pins_a: usbotg-hs-0 {
pins {
pinmux = <STM32_PINMUX('A', 10, ANALOG)>; /* OTG_ID */
--
2.17.1
next prev parent reply other threads:[~2020-05-28 7:40 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-05-28 7:40 [PATCH 0/5] STM32 add usart nodes support Erwan Le Ray
2020-05-28 7:40 ` Erwan Le Ray [this message]
2020-06-15 10:49 ` [PATCH 1/5] ARM: dts: stm32: add usart2, usart3 and uart7 pins in stm32mp15-pinctrl Alexandre Torgue
2020-05-28 7:40 ` [PATCH 2/5] ARM: dts: stm32: add usart3 node to stm32mp15xx-dkx boards Erwan Le Ray
2020-05-28 7:40 ` [PATCH 3/5] ARM: dts: stm32: add usart3 node to stm32mp157c-ev1 Erwan Le Ray
2020-05-28 7:40 ` [PATCH 4/5] ARM: dts: stm32: add uart7 support to stm32mp15xx-dkx boards Erwan Le Ray
2020-05-28 7:40 ` [PATCH 5/5] ARM: dts: stm32: add usart2 node to stm32mp157c-dk2 Erwan Le Ray
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200528074029.24962-2-erwan.leray@st.com \
--to=erwan.leray@st.com \
--cc=alexandre.torgue@st.com \
--cc=devicetree@vger.kernel.org \
--cc=fabrice.gasnier@st.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-stm32@st-md-mailman.stormreply.com \
--cc=mark.rutland@arm.com \
--cc=mcoquelin.stm32@gmail.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox