Re: [PATCH v3 104/105] dt-bindings: display: vc4: hdmi: Add BCM2711 HDMI controllers bindings

[Rob Herring <robh@kernel.org>]

On Wed, May 27, 2020 at 05:49:14PM +0200, Maxime Ripard wrote:
> The HDMI controllers found in the BCM2711 SoC need some adjustments to the
> bindings, especially since the registers have been shuffled around in more
> register ranges.
> 
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: devicetree@vger.kernel.org
> Signed-off-by: Maxime Ripard <maxime@cerno.tech>
> ---
>  Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml | 109 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++-
>  1 file changed, 109 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
> 
> diff --git a/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml b/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
> new file mode 100644
> index 000000000000..6091fe3d315b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
> @@ -0,0 +1,109 @@
> +# SPDX-License-Identifier: GPL-2.0

Dual license...

> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/brcm,bcm2711-hdmi.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Broadcom BCM2711 HDMI Controller Device Tree Bindings
> +
> +maintainers:
> +  - Eric Anholt <eric@anholt.net>
> +
> +properties:
> +  compatible:
> +    enum:
> +      - brcm,bcm2711-hdmi0
> +      - brcm,bcm2711-hdmi1

What's the difference between the 2 blocks? 

> +
> +  reg:
> +    items:
> +      - description: HDMI controller register range
> +      - description: DVP register range
> +      - description: HDMI PHY register range
> +      - description: Rate Manager register range
> +      - description: Packet RAM register range
> +      - description: Metadata RAM register range
> +      - description: CSC register range
> +      - description: CEC register range
> +      - description: HD register range
> +
> +  reg-names:
> +    items:
> +      - const: hdmi
> +      - const: dvp
> +      - const: phy
> +      - const: rm
> +      - const: packet
> +      - const: metadata
> +      - const: csc
> +      - const: cec
> +      - const: hd
> +
> +  clocks:
> +    description: The HDMI state machine clock
> +
> +  clock-names:
> +    const: hdmi
> +
> +  ddc:
> +    allOf:
> +      - $ref: /schemas/types.yaml#/definitions/phandle
> +    description: >
> +      Phandle of the I2C controller used for DDC EDID probing

Goes in the connector.

And isn't the standard name ddc-i2c-bus?

> +
> +  hpd-gpios:
> +    description: >
> +      The GPIO pin for the HDMI hotplug detect (if it doesn't appear
> +      as an interrupt/status bit in the HDMI controller itself)

Goes in the connector.

> +
> +  dmas:
> +    maxItems: 1
> +    description: >
> +      Should contain one entry pointing to the DMA channel used to
> +      transfer audio data.
> +
> +  dma-names:
> +    const: audio-rx
> +
> +  resets:
> +    maxItems: 1
> +
> +required:
> +  - compatible
> +  - reg
> +  - reg-names
> +  - clocks
> +  - resets
> +  - ddc
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    hdmi0: hdmi@7ef00700 {
> +        compatible = "brcm,bcm2711-hdmi0";
> +        reg = <0x7ef00700 0x300>,
> +              <0x7ef00300 0x200>,
> +              <0x7ef00f00 0x80>,
> +              <0x7ef00f80 0x80>,
> +              <0x7ef01b00 0x200>,
> +              <0x7ef01f00 0x400>,
> +              <0x7ef00200 0x80>,
> +              <0x7ef04300 0x100>,
> +              <0x7ef20000 0x100>;
> +        reg-names = "hdmi",
> +                    "dvp",
> +                    "phy",
> +                    "rm",
> +                    "packet",
> +                    "metadata",
> +                    "csc",
> +                    "cec",
> +                    "hd";
> +        clocks = <&firmware_clocks 13>;
> +        clock-names = "hdmi";
> +        resets = <&dvp 0>;
> +        ddc = <&ddc0>;
> +    };
> +
> +...
> -- 
> git-series 0.9.1