* [PATCH 2/3] arm64: dts: qcom: sm8250-mtp: include pmic files
2020-06-21 19:28 [PATCH 1/3] arm64: dts: qcom: pm8009: Add base dts file Dmitry Baryshkov
@ 2020-06-21 19:28 ` Dmitry Baryshkov
2020-06-22 1:34 ` kernel test robot
2020-06-22 7:25 ` kernel test robot
2020-06-21 19:28 ` [PATCH 3/3] arm64: dts: qcom: pm8150x: add thermal alarms and thermal zones Dmitry Baryshkov
2020-06-21 19:34 ` [PATCH 1/3] arm64: dts: qcom: pm8009: Add base dts file Bjorn Andersson
2 siblings, 2 replies; 6+ messages in thread
From: Dmitry Baryshkov @ 2020-06-21 19:28 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Rob Herring
Cc: linux-arm-msm, devicetree, Vinod Koul
Include files describing used PMIC chips, GPIOs, power on, etc nodes.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8250-mtp.dts | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
index cff7a85890ee..aa37eb112d85 100644
--- a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
@@ -7,6 +7,10 @@
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
#include "sm8250.dtsi"
+#include "pm8150.dtsi"
+#include "pm8150b.dtsi"
+#include "pm8150l.dtsi"
+#include "pm8009.dtsi"
/ {
model = "Qualcomm Technologies, Inc. SM8250 MTP";
--
2.27.0
^ permalink raw reply related [flat|nested] 6+ messages in thread* [PATCH 3/3] arm64: dts: qcom: pm8150x: add thermal alarms and thermal zones
2020-06-21 19:28 [PATCH 1/3] arm64: dts: qcom: pm8009: Add base dts file Dmitry Baryshkov
2020-06-21 19:28 ` [PATCH 2/3] arm64: dts: qcom: sm8250-mtp: include pmic files Dmitry Baryshkov
@ 2020-06-21 19:28 ` Dmitry Baryshkov
2020-06-21 19:34 ` [PATCH 1/3] arm64: dts: qcom: pm8009: Add base dts file Bjorn Andersson
2 siblings, 0 replies; 6+ messages in thread
From: Dmitry Baryshkov @ 2020-06-21 19:28 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Rob Herring
Cc: linux-arm-msm, devicetree, Vinod Koul
Add temperature alarm and thermal zone configuration to all three
pm8150 instances. Configuration is largely based on the msm-4.19 tree.
These alarms use main adc of the pmic. Separate temperature adc is not
supported yet.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
arch/arm64/boot/dts/qcom/pm8150.dtsi | 42 +++++++++++++++++++++++--
arch/arm64/boot/dts/qcom/pm8150b.dtsi | 44 +++++++++++++++++++++++++--
arch/arm64/boot/dts/qcom/pm8150l.dtsi | 44 +++++++++++++++++++++++++--
3 files changed, 122 insertions(+), 8 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/pm8150.dtsi b/arch/arm64/boot/dts/qcom/pm8150.dtsi
index c0b197458665..1b6406927509 100644
--- a/arch/arm64/boot/dts/qcom/pm8150.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8150.dtsi
@@ -9,6 +9,37 @@
#include <dt-bindings/spmi/spmi.h>
#include <dt-bindings/iio/qcom,spmi-vadc.h>
+/ {
+ thermal-zones {
+ pm8150 {
+ polling-delay-passive = <100>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&pm8150_temp>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+
+ trip2 {
+ temperature = <145000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+ };
+};
+
&spmi_bus {
pm8150_0: pmic@0 {
compatible = "qcom,pm8150", "qcom,spmi-pmic";
@@ -30,6 +61,15 @@ pwrkey {
};
};
+ pm8150_temp: temp-alarm@2400 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0x2400>;
+ interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+ io-channels = <&pm8150_adc ADC5_DIE_TEMP>;
+ io-channel-names = "thermal";
+ #thermal-sensor-cells = <0>;
+ };
+
pm8150_adc: adc@3100 {
compatible = "qcom,spmi-adc5";
reg = <0x3100>;
@@ -38,8 +78,6 @@ pm8150_adc: adc@3100 {
#io-channel-cells = <1>;
interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
- status = "disabled";
-
ref-gnd@0 {
reg = <ADC5_REF_GND>;
qcom,pre-scaling = <1 1>;
diff --git a/arch/arm64/boot/dts/qcom/pm8150b.dtsi b/arch/arm64/boot/dts/qcom/pm8150b.dtsi
index 40b5d75a4a1d..e112e8876db6 100644
--- a/arch/arm64/boot/dts/qcom/pm8150b.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8150b.dtsi
@@ -8,6 +8,37 @@
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/spmi/spmi.h>
+/ {
+ thermal-zones {
+ pm8150b {
+ polling-delay-passive = <100>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&pm8150b_temp>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+
+ trip2 {
+ temperature = <145000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+ };
+};
+
&spmi_bus {
pmic@2 {
compatible = "qcom,pm8150b", "qcom,spmi-pmic";
@@ -22,7 +53,16 @@ power-on@800 {
status = "disabled";
};
- adc@3100 {
+ pm8150b_temp: temp-alarm@2400 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0x2400>;
+ interrupts = <0x2 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+ io-channels = <&pm8150b_adc ADC5_DIE_TEMP>;
+ io-channel-names = "thermal";
+ #thermal-sensor-cells = <0>;
+ };
+
+ pm8150b_adc: adc@3100 {
compatible = "qcom,spmi-adc5";
reg = <0x3100>;
#address-cells = <1>;
@@ -30,8 +70,6 @@ adc@3100 {
#io-channel-cells = <1>;
interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
- status = "disabled";
-
ref-gnd@0 {
reg = <ADC5_REF_GND>;
qcom,pre-scaling = <1 1>;
diff --git a/arch/arm64/boot/dts/qcom/pm8150l.dtsi b/arch/arm64/boot/dts/qcom/pm8150l.dtsi
index cf05e0685d10..62139538b7d9 100644
--- a/arch/arm64/boot/dts/qcom/pm8150l.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8150l.dtsi
@@ -8,6 +8,37 @@
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/spmi/spmi.h>
+/ {
+ thermal-zones {
+ pm8150l {
+ polling-delay-passive = <100>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&pm8150l_temp>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+
+ trip2 {
+ temperature = <145000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+ };
+};
+
&spmi_bus {
pmic@4 {
compatible = "qcom,pm8150l", "qcom,spmi-pmic";
@@ -22,7 +53,16 @@ power-on@800 {
status = "disabled";
};
- adc@3100 {
+ pm8150l_temp: temp-alarm@2400 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0x2400>;
+ interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+ io-channels = <&pm8150l_adc ADC5_DIE_TEMP>;
+ io-channel-names = "thermal";
+ #thermal-sensor-cells = <0>;
+ };
+
+ pm8150l_adc: adc@3100 {
compatible = "qcom,spmi-adc5";
reg = <0x3100>;
#address-cells = <1>;
@@ -30,8 +70,6 @@ adc@3100 {
#io-channel-cells = <1>;
interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
- status = "disabled";
-
ref-gnd@0 {
reg = <ADC5_REF_GND>;
qcom,pre-scaling = <1 1>;
--
2.27.0
^ permalink raw reply related [flat|nested] 6+ messages in thread* Re: [PATCH 1/3] arm64: dts: qcom: pm8009: Add base dts file
2020-06-21 19:28 [PATCH 1/3] arm64: dts: qcom: pm8009: Add base dts file Dmitry Baryshkov
2020-06-21 19:28 ` [PATCH 2/3] arm64: dts: qcom: sm8250-mtp: include pmic files Dmitry Baryshkov
2020-06-21 19:28 ` [PATCH 3/3] arm64: dts: qcom: pm8150x: add thermal alarms and thermal zones Dmitry Baryshkov
@ 2020-06-21 19:34 ` Bjorn Andersson
2 siblings, 0 replies; 6+ messages in thread
From: Bjorn Andersson @ 2020-06-21 19:34 UTC (permalink / raw)
To: Dmitry Baryshkov
Cc: Andy Gross, Rob Herring, linux-arm-msm, devicetree, Vinod Koul
On Sun 21 Jun 12:28 PDT 2020, Dmitry Baryshkov wrote:
> Add base DTS file for pm8009 along with GPIOs and power-on nodes.
>
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
I took the liberty of adding a pm8009_pon label to the pon node, then
applied the three patches.
Thanks,
Bjorn
> ---
> arch/arm64/boot/dts/qcom/pm8009.dtsi | 37 ++++++++++++++++++++++++++++
> 1 file changed, 37 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/pm8009.dtsi
>
> diff --git a/arch/arm64/boot/dts/qcom/pm8009.dtsi b/arch/arm64/boot/dts/qcom/pm8009.dtsi
> new file mode 100644
> index 000000000000..cb1a10e72474
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/pm8009.dtsi
> @@ -0,0 +1,37 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2020, Linaro Limited
> + */
> +
> +#include <dt-bindings/spmi/spmi.h>
> +
> +&spmi_bus {
> + pmic@a {
> + compatible = "qcom,pm8009", "qcom,spmi-pmic";
> + reg = <0xa SPMI_USID>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pon@800 {
> + compatible = "qcom,pm8916-pon";
> + reg = <0x0800>;
> + };
> +
> + pm8009_gpios: gpio@c000 {
> + compatible = "qcom,pm8005-gpio";
> + reg = <0xc000>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +
> + pmic@b {
> + compatible = "qcom,pm8009", "qcom,spmi-pmic";
> + reg = <0xb SPMI_USID>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +};
> --
> 2.27.0
>
^ permalink raw reply [flat|nested] 6+ messages in thread