* [PATCH] ARM: dts: ZII: Disable HW Ethernet switch reset GPIO
@ 2020-07-15 21:22 Chris Healy
2020-07-20 3:15 ` Shawn Guo
0 siblings, 1 reply; 3+ messages in thread
From: Chris Healy @ 2020-07-15 21:22 UTC (permalink / raw)
To: shawnguo, s.hauer, stefan, robh+dt, linux-arm-kernel, devicetree,
linux-kernel, festevam
Cc: Chris Healy
Disable Ethernet switch reset GPIO with ZII platforms that have it
enabled to sync up with existing ZII platforms that already have
it disabled.
Signed-off-by: Chris Healy <cphealy@gmail.com>
---
arch/arm/boot/dts/vf610-zii-cfu1.dts | 2 --
arch/arm/boot/dts/vf610-zii-spb4.dts | 2 --
arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts | 2 --
arch/arm/boot/dts/vf610-zii-ssmb-spu3.dts | 2 --
4 files changed, 8 deletions(-)
diff --git a/arch/arm/boot/dts/vf610-zii-cfu1.dts b/arch/arm/boot/dts/vf610-zii-cfu1.dts
index ce1920c052fc..c2668230a4c0 100644
--- a/arch/arm/boot/dts/vf610-zii-cfu1.dts
+++ b/arch/arm/boot/dts/vf610-zii-cfu1.dts
@@ -170,7 +170,6 @@
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
interrupt-controller;
#interrupt-cells = <2>;
- reset-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
ports {
#address-cells = <1>;
@@ -354,7 +353,6 @@
pinctrl_switch: switch-grp {
fsl,pins = <
VF610_PAD_PTB28__GPIO_98 0x3061
- VF610_PAD_PTE2__GPIO_107 0x1042
>;
};
diff --git a/arch/arm/boot/dts/vf610-zii-spb4.dts b/arch/arm/boot/dts/vf610-zii-spb4.dts
index 55b4201e27f6..261317340189 100644
--- a/arch/arm/boot/dts/vf610-zii-spb4.dts
+++ b/arch/arm/boot/dts/vf610-zii-spb4.dts
@@ -127,7 +127,6 @@
pinctrl-names = "default";
reg = <0>;
eeprom-length = <65536>;
- reset-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
interrupt-parent = <&gpio3>;
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
interrupt-controller;
@@ -312,7 +311,6 @@
pinctrl_gpio_switch0: pinctrl-gpio-switch0 {
fsl,pins = <
- VF610_PAD_PTE2__GPIO_107 0x31c2
VF610_PAD_PTB28__GPIO_98 0x219d
>;
};
diff --git a/arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts b/arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts
index a6c22a79779e..e37b9643269b 100644
--- a/arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts
+++ b/arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts
@@ -113,7 +113,6 @@
pinctrl-names = "default";
reg = <0>;
eeprom-length = <65536>;
- reset-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
interrupt-parent = <&gpio3>;
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
interrupt-controller;
@@ -288,7 +287,6 @@
pinctrl_gpio_switch0: pinctrl-gpio-switch0 {
fsl,pins = <
- VF610_PAD_PTE2__GPIO_107 0x31c2
VF610_PAD_PTB28__GPIO_98 0x219d
>;
};
diff --git a/arch/arm/boot/dts/vf610-zii-ssmb-spu3.dts b/arch/arm/boot/dts/vf610-zii-ssmb-spu3.dts
index 3d05c894bdc0..b3d6d4b9fa9c 100644
--- a/arch/arm/boot/dts/vf610-zii-ssmb-spu3.dts
+++ b/arch/arm/boot/dts/vf610-zii-ssmb-spu3.dts
@@ -141,7 +141,6 @@
pinctrl-names = "default";
reg = <0>;
eeprom-length = <65536>;
- reset-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
interrupt-parent = <&gpio3>;
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
interrupt-controller;
@@ -319,7 +318,6 @@
pinctrl_gpio_switch0: pinctrl-gpio-switch0 {
fsl,pins = <
- VF610_PAD_PTE2__GPIO_107 0x31c2
VF610_PAD_PTB28__GPIO_98 0x219d
>;
};
--
2.21.3
^ permalink raw reply related [flat|nested] 3+ messages in thread* Re: [PATCH] ARM: dts: ZII: Disable HW Ethernet switch reset GPIO
2020-07-15 21:22 [PATCH] ARM: dts: ZII: Disable HW Ethernet switch reset GPIO Chris Healy
@ 2020-07-20 3:15 ` Shawn Guo
2020-07-20 4:48 ` Chris Healy
0 siblings, 1 reply; 3+ messages in thread
From: Shawn Guo @ 2020-07-20 3:15 UTC (permalink / raw)
To: Chris Healy
Cc: s.hauer, stefan, robh+dt, linux-arm-kernel, devicetree,
linux-kernel, festevam
On Wed, Jul 15, 2020 at 02:22:27PM -0700, Chris Healy wrote:
> Disable Ethernet switch reset GPIO with ZII platforms that have it
> enabled to sync up with existing ZII platforms that already have
> it disabled.
I do not follow it. The reset GPIO is part of hardware description. We
shouldn't add or remove it for sake of sync-up with other platforms.
Shawn
>
> Signed-off-by: Chris Healy <cphealy@gmail.com>
> ---
> arch/arm/boot/dts/vf610-zii-cfu1.dts | 2 --
> arch/arm/boot/dts/vf610-zii-spb4.dts | 2 --
> arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts | 2 --
> arch/arm/boot/dts/vf610-zii-ssmb-spu3.dts | 2 --
> 4 files changed, 8 deletions(-)
>
> diff --git a/arch/arm/boot/dts/vf610-zii-cfu1.dts b/arch/arm/boot/dts/vf610-zii-cfu1.dts
> index ce1920c052fc..c2668230a4c0 100644
> --- a/arch/arm/boot/dts/vf610-zii-cfu1.dts
> +++ b/arch/arm/boot/dts/vf610-zii-cfu1.dts
> @@ -170,7 +170,6 @@
> interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
> interrupt-controller;
> #interrupt-cells = <2>;
> - reset-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
>
> ports {
> #address-cells = <1>;
> @@ -354,7 +353,6 @@
> pinctrl_switch: switch-grp {
> fsl,pins = <
> VF610_PAD_PTB28__GPIO_98 0x3061
> - VF610_PAD_PTE2__GPIO_107 0x1042
> >;
> };
>
> diff --git a/arch/arm/boot/dts/vf610-zii-spb4.dts b/arch/arm/boot/dts/vf610-zii-spb4.dts
> index 55b4201e27f6..261317340189 100644
> --- a/arch/arm/boot/dts/vf610-zii-spb4.dts
> +++ b/arch/arm/boot/dts/vf610-zii-spb4.dts
> @@ -127,7 +127,6 @@
> pinctrl-names = "default";
> reg = <0>;
> eeprom-length = <65536>;
> - reset-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
> interrupt-parent = <&gpio3>;
> interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
> interrupt-controller;
> @@ -312,7 +311,6 @@
>
> pinctrl_gpio_switch0: pinctrl-gpio-switch0 {
> fsl,pins = <
> - VF610_PAD_PTE2__GPIO_107 0x31c2
> VF610_PAD_PTB28__GPIO_98 0x219d
> >;
> };
> diff --git a/arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts b/arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts
> index a6c22a79779e..e37b9643269b 100644
> --- a/arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts
> +++ b/arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts
> @@ -113,7 +113,6 @@
> pinctrl-names = "default";
> reg = <0>;
> eeprom-length = <65536>;
> - reset-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
> interrupt-parent = <&gpio3>;
> interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
> interrupt-controller;
> @@ -288,7 +287,6 @@
>
> pinctrl_gpio_switch0: pinctrl-gpio-switch0 {
> fsl,pins = <
> - VF610_PAD_PTE2__GPIO_107 0x31c2
> VF610_PAD_PTB28__GPIO_98 0x219d
> >;
> };
> diff --git a/arch/arm/boot/dts/vf610-zii-ssmb-spu3.dts b/arch/arm/boot/dts/vf610-zii-ssmb-spu3.dts
> index 3d05c894bdc0..b3d6d4b9fa9c 100644
> --- a/arch/arm/boot/dts/vf610-zii-ssmb-spu3.dts
> +++ b/arch/arm/boot/dts/vf610-zii-ssmb-spu3.dts
> @@ -141,7 +141,6 @@
> pinctrl-names = "default";
> reg = <0>;
> eeprom-length = <65536>;
> - reset-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
> interrupt-parent = <&gpio3>;
> interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
> interrupt-controller;
> @@ -319,7 +318,6 @@
>
> pinctrl_gpio_switch0: pinctrl-gpio-switch0 {
> fsl,pins = <
> - VF610_PAD_PTE2__GPIO_107 0x31c2
> VF610_PAD_PTB28__GPIO_98 0x219d
> >;
> };
> --
> 2.21.3
>
^ permalink raw reply [flat|nested] 3+ messages in thread* Re: [PATCH] ARM: dts: ZII: Disable HW Ethernet switch reset GPIO
2020-07-20 3:15 ` Shawn Guo
@ 2020-07-20 4:48 ` Chris Healy
0 siblings, 0 replies; 3+ messages in thread
From: Chris Healy @ 2020-07-20 4:48 UTC (permalink / raw)
To: Shawn Guo
Cc: Sascha Hauer, Stefan Agner, Rob Herring, linux ARM,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
linux-kernel, Fabio Estevam
On Sun, Jul 19, 2020 at 8:15 PM Shawn Guo <shawnguo@kernel.org> wrote:
>
> On Wed, Jul 15, 2020 at 02:22:27PM -0700, Chris Healy wrote:
> > Disable Ethernet switch reset GPIO with ZII platforms that have it
> > enabled to sync up with existing ZII platforms that already have
> > it disabled.
>
> I do not follow it. The reset GPIO is part of hardware description. We
> shouldn't add or remove it for sake of sync-up with other platforms.
I see that my description is not very good. What I should have said
is that we don't want to use the HW reset GPIO as it results in things
being done that we do not want done. Specifically, when the switch is
hit with the HW reset GPIO, it results in the switch's copper PHYs
being HW reset which we want to avoid as this results in unnecessary
network downtime on a soft reboot of the processor. With the HW reset
GPIO not in the devicetree description, the switch driver resorts to
doing a SW reset which resets the switch core but not the switch's
copper PHYs. This results in a much shorter network downtime on a
soft reboot of the processor.
I can do a v2 of the patch with the description updated if you think
it would be appropriate.
>
> Shawn
>
> >
> > Signed-off-by: Chris Healy <cphealy@gmail.com>
> > ---
> > arch/arm/boot/dts/vf610-zii-cfu1.dts | 2 --
> > arch/arm/boot/dts/vf610-zii-spb4.dts | 2 --
> > arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts | 2 --
> > arch/arm/boot/dts/vf610-zii-ssmb-spu3.dts | 2 --
> > 4 files changed, 8 deletions(-)
> >
> > diff --git a/arch/arm/boot/dts/vf610-zii-cfu1.dts b/arch/arm/boot/dts/vf610-zii-cfu1.dts
> > index ce1920c052fc..c2668230a4c0 100644
> > --- a/arch/arm/boot/dts/vf610-zii-cfu1.dts
> > +++ b/arch/arm/boot/dts/vf610-zii-cfu1.dts
> > @@ -170,7 +170,6 @@
> > interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
> > interrupt-controller;
> > #interrupt-cells = <2>;
> > - reset-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
> >
> > ports {
> > #address-cells = <1>;
> > @@ -354,7 +353,6 @@
> > pinctrl_switch: switch-grp {
> > fsl,pins = <
> > VF610_PAD_PTB28__GPIO_98 0x3061
> > - VF610_PAD_PTE2__GPIO_107 0x1042
> > >;
> > };
> >
> > diff --git a/arch/arm/boot/dts/vf610-zii-spb4.dts b/arch/arm/boot/dts/vf610-zii-spb4.dts
> > index 55b4201e27f6..261317340189 100644
> > --- a/arch/arm/boot/dts/vf610-zii-spb4.dts
> > +++ b/arch/arm/boot/dts/vf610-zii-spb4.dts
> > @@ -127,7 +127,6 @@
> > pinctrl-names = "default";
> > reg = <0>;
> > eeprom-length = <65536>;
> > - reset-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
> > interrupt-parent = <&gpio3>;
> > interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
> > interrupt-controller;
> > @@ -312,7 +311,6 @@
> >
> > pinctrl_gpio_switch0: pinctrl-gpio-switch0 {
> > fsl,pins = <
> > - VF610_PAD_PTE2__GPIO_107 0x31c2
> > VF610_PAD_PTB28__GPIO_98 0x219d
> > >;
> > };
> > diff --git a/arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts b/arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts
> > index a6c22a79779e..e37b9643269b 100644
> > --- a/arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts
> > +++ b/arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts
> > @@ -113,7 +113,6 @@
> > pinctrl-names = "default";
> > reg = <0>;
> > eeprom-length = <65536>;
> > - reset-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
> > interrupt-parent = <&gpio3>;
> > interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
> > interrupt-controller;
> > @@ -288,7 +287,6 @@
> >
> > pinctrl_gpio_switch0: pinctrl-gpio-switch0 {
> > fsl,pins = <
> > - VF610_PAD_PTE2__GPIO_107 0x31c2
> > VF610_PAD_PTB28__GPIO_98 0x219d
> > >;
> > };
> > diff --git a/arch/arm/boot/dts/vf610-zii-ssmb-spu3.dts b/arch/arm/boot/dts/vf610-zii-ssmb-spu3.dts
> > index 3d05c894bdc0..b3d6d4b9fa9c 100644
> > --- a/arch/arm/boot/dts/vf610-zii-ssmb-spu3.dts
> > +++ b/arch/arm/boot/dts/vf610-zii-ssmb-spu3.dts
> > @@ -141,7 +141,6 @@
> > pinctrl-names = "default";
> > reg = <0>;
> > eeprom-length = <65536>;
> > - reset-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
> > interrupt-parent = <&gpio3>;
> > interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
> > interrupt-controller;
> > @@ -319,7 +318,6 @@
> >
> > pinctrl_gpio_switch0: pinctrl-gpio-switch0 {
> > fsl,pins = <
> > - VF610_PAD_PTE2__GPIO_107 0x31c2
> > VF610_PAD_PTB28__GPIO_98 0x219d
> > >;
> > };
> > --
> > 2.21.3
> >
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2020-07-20 4:49 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2020-07-15 21:22 [PATCH] ARM: dts: ZII: Disable HW Ethernet switch reset GPIO Chris Healy
2020-07-20 3:15 ` Shawn Guo
2020-07-20 4:48 ` Chris Healy
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).