* [PATCH v5 0/3] arm: dts: add and modify device node in NPCM7xx device tree
@ 2020-09-16 12:55 Tomer Maimon
2020-09-16 12:55 ` [PATCH v5 1/3] arm: dts: modify NPCM7xx device tree clock parameter Tomer Maimon
` (3 more replies)
0 siblings, 4 replies; 8+ messages in thread
From: Tomer Maimon @ 2020-09-16 12:55 UTC (permalink / raw)
To: robh+dt, mark.rutland, avifishman70, tali.perry1, venture, yuenn,
benjaminfair, joel
Cc: devicetree, linux-kernel, openbmc, tmaimon77
This patch set adds and modify device tree nodes in the NPCM7xx
Baseboard Management Controller (BMC) device tree.
The following device node add:
- NPCM7xx Pin controller and GPIO
- NPCM7xx PWM and FAN.
- NPCM7xx EHCI USB.
- NPCM7xx KCS.
- NPCM Reset.
- NPCM Peripheral SPI.
- NPCM FIU SPI.
- NPCM HWRNG.
- NPCM I2C.
- STMicro STMMAC.
The following device node modified:
- NPCM7xx timer.
- NPCM7xx clock constants parameters.
NPCM7xx device tree tested on NPCM750 evaluation board.
Changes since version 4:
- Tested patches in Linux kernel 5.9.
Changes since version 3:
- Tested patches in Linux kernel 5.6.
Changes since version 2:
- Remove unnecessary output-enable flags.
Changes since version 1:
- Add NPCM reset device node.
- Add reset parameters to NPCM driver device nodes.
Tomer Maimon (3):
arm: dts: modify NPCM7xx device tree clock parameter
arm: dts: modify NPCM7xx device tree timer register size
arm: dts: add new device nodes to NPCM750 device tree
arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi | 974 +++++++++++++++++-
arch/arm/boot/dts/nuvoton-npcm750-evb.dts | 404 +++++++-
.../boot/dts/nuvoton-npcm750-pincfg-evb.dtsi | 157 +++
arch/arm/boot/dts/nuvoton-npcm750.dtsi | 24 +-
4 files changed, 1522 insertions(+), 37 deletions(-)
create mode 100644 arch/arm/boot/dts/nuvoton-npcm750-pincfg-evb.dtsi
--
2.22.0
^ permalink raw reply [flat|nested] 8+ messages in thread* [PATCH v5 1/3] arm: dts: modify NPCM7xx device tree clock parameter 2020-09-16 12:55 [PATCH v5 0/3] arm: dts: add and modify device node in NPCM7xx device tree Tomer Maimon @ 2020-09-16 12:55 ` Tomer Maimon 2020-09-16 13:15 ` Joel Stanley 2020-09-16 12:55 ` [PATCH v5 2/3] arm: dts: modify NPCM7xx device tree timer register size Tomer Maimon ` (2 subsequent siblings) 3 siblings, 1 reply; 8+ messages in thread From: Tomer Maimon @ 2020-09-16 12:55 UTC (permalink / raw) To: robh+dt, mark.rutland, avifishman70, tali.perry1, venture, yuenn, benjaminfair, joel Cc: devicetree, linux-kernel, openbmc, tmaimon77 Modify NPCM7xx device tree clock parameter to clock constants that define at include/dt-bindings/clock/nuvoton,npcm7xx-clock.h file. Signed-off-by: Tomer Maimon <tmaimon77@gmail.com> --- arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi | 19 ++++++++++--------- arch/arm/boot/dts/nuvoton-npcm750.dtsi | 6 +++--- 2 files changed, 13 insertions(+), 12 deletions(-) diff --git a/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi b/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi index d2d0761295a4..16a28c5c4131 100644 --- a/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi +++ b/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi @@ -3,6 +3,7 @@ // Copyright 2018 Google, Inc. #include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/clock/nuvoton,npcm7xx-clock.h> / { #address-cells = <1>; @@ -80,7 +81,7 @@ interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; cache-unified; cache-level = <2>; - clocks = <&clk 10>; + clocks = <&clk NPCM7XX_CLK_AXI>; arm,shared-override; }; @@ -120,7 +121,7 @@ compatible = "nuvoton,npcm750-timer"; interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; reg = <0x8000 0x50>; - clocks = <&clk 5>; + clocks = <&clk NPCM7XX_CLK_TIMER>; }; watchdog0: watchdog@801C { @@ -128,7 +129,7 @@ interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; reg = <0x801C 0x4>; status = "disabled"; - clocks = <&clk 5>; + clocks = <&clk NPCM7XX_CLK_TIMER>; }; watchdog1: watchdog@901C { @@ -136,7 +137,7 @@ interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; reg = <0x901C 0x4>; status = "disabled"; - clocks = <&clk 5>; + clocks = <&clk NPCM7XX_CLK_TIMER>; }; watchdog2: watchdog@a01C { @@ -144,13 +145,13 @@ interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; reg = <0xa01C 0x4>; status = "disabled"; - clocks = <&clk 5>; + clocks = <&clk NPCM7XX_CLK_TIMER>; }; serial0: serial@1000 { compatible = "nuvoton,npcm750-uart"; reg = <0x1000 0x1000>; - clocks = <&clk 6>; + clocks = <&clk NPCM7XX_CLK_UART>; interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; reg-shift = <2>; status = "disabled"; @@ -159,7 +160,7 @@ serial1: serial@2000 { compatible = "nuvoton,npcm750-uart"; reg = <0x2000 0x1000>; - clocks = <&clk 6>; + clocks = <&clk NPCM7XX_CLK_UART>; interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; reg-shift = <2>; status = "disabled"; @@ -168,7 +169,7 @@ serial2: serial@3000 { compatible = "nuvoton,npcm750-uart"; reg = <0x3000 0x1000>; - clocks = <&clk 6>; + clocks = <&clk NPCM7XX_CLK_UART>; interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; reg-shift = <2>; status = "disabled"; @@ -177,7 +178,7 @@ serial3: serial@4000 { compatible = "nuvoton,npcm750-uart"; reg = <0x4000 0x1000>; - clocks = <&clk 6>; + clocks = <&clk NPCM7XX_CLK_UART>; interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; reg-shift = <2>; status = "disabled"; diff --git a/arch/arm/boot/dts/nuvoton-npcm750.dtsi b/arch/arm/boot/dts/nuvoton-npcm750.dtsi index 6ac340533587..a37bb2294b8f 100644 --- a/arch/arm/boot/dts/nuvoton-npcm750.dtsi +++ b/arch/arm/boot/dts/nuvoton-npcm750.dtsi @@ -17,7 +17,7 @@ cpu@0 { device_type = "cpu"; compatible = "arm,cortex-a9"; - clocks = <&clk 0>; + clocks = <&clk NPCM7XX_CLK_CPU>; clock-names = "clk_cpu"; reg = <0>; next-level-cache = <&l2>; @@ -26,7 +26,7 @@ cpu@1 { device_type = "cpu"; compatible = "arm,cortex-a9"; - clocks = <&clk 0>; + clocks = <&clk NPCM7XX_CLK_CPU>; clock-names = "clk_cpu"; reg = <1>; next-level-cache = <&l2>; @@ -38,7 +38,7 @@ reg = <0x3fe600 0x20>; interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>; - clocks = <&clk 5>; + clocks = <&clk NPCM7XX_CLK_AHB>; }; }; }; -- 2.22.0 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH v5 1/3] arm: dts: modify NPCM7xx device tree clock parameter 2020-09-16 12:55 ` [PATCH v5 1/3] arm: dts: modify NPCM7xx device tree clock parameter Tomer Maimon @ 2020-09-16 13:15 ` Joel Stanley 0 siblings, 0 replies; 8+ messages in thread From: Joel Stanley @ 2020-09-16 13:15 UTC (permalink / raw) To: Tomer Maimon Cc: Rob Herring, Mark Rutland, Avi Fishman, Tali Perry, Patrick Venture, Nancy Yuen, Benjamin Fair, devicetree, Linux Kernel Mailing List, OpenBMC Maillist On Wed, 16 Sep 2020 at 12:56, Tomer Maimon <tmaimon77@gmail.com> wrote: > > Modify NPCM7xx device tree clock parameter to clock constants that > define at include/dt-bindings/clock/nuvoton,npcm7xx-clock.h file. > > Signed-off-by: Tomer Maimon <tmaimon77@gmail.com> Reviewed-by: Joel Stanley <joel@jms.id.au> > --- > arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi | 19 ++++++++++--------- > arch/arm/boot/dts/nuvoton-npcm750.dtsi | 6 +++--- > 2 files changed, 13 insertions(+), 12 deletions(-) > > diff --git a/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi b/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi > index d2d0761295a4..16a28c5c4131 100644 > --- a/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi > +++ b/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi > @@ -3,6 +3,7 @@ > // Copyright 2018 Google, Inc. > > #include <dt-bindings/interrupt-controller/arm-gic.h> > +#include <dt-bindings/clock/nuvoton,npcm7xx-clock.h> > > / { > #address-cells = <1>; > @@ -80,7 +81,7 @@ > interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; > cache-unified; > cache-level = <2>; > - clocks = <&clk 10>; > + clocks = <&clk NPCM7XX_CLK_AXI>; > arm,shared-override; > }; > > @@ -120,7 +121,7 @@ > compatible = "nuvoton,npcm750-timer"; > interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; > reg = <0x8000 0x50>; > - clocks = <&clk 5>; > + clocks = <&clk NPCM7XX_CLK_TIMER>; > }; > > watchdog0: watchdog@801C { > @@ -128,7 +129,7 @@ > interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; > reg = <0x801C 0x4>; > status = "disabled"; > - clocks = <&clk 5>; > + clocks = <&clk NPCM7XX_CLK_TIMER>; > }; > > watchdog1: watchdog@901C { > @@ -136,7 +137,7 @@ > interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; > reg = <0x901C 0x4>; > status = "disabled"; > - clocks = <&clk 5>; > + clocks = <&clk NPCM7XX_CLK_TIMER>; > }; > > watchdog2: watchdog@a01C { > @@ -144,13 +145,13 @@ > interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; > reg = <0xa01C 0x4>; > status = "disabled"; > - clocks = <&clk 5>; > + clocks = <&clk NPCM7XX_CLK_TIMER>; > }; > > serial0: serial@1000 { > compatible = "nuvoton,npcm750-uart"; > reg = <0x1000 0x1000>; > - clocks = <&clk 6>; > + clocks = <&clk NPCM7XX_CLK_UART>; > interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; > reg-shift = <2>; > status = "disabled"; > @@ -159,7 +160,7 @@ > serial1: serial@2000 { > compatible = "nuvoton,npcm750-uart"; > reg = <0x2000 0x1000>; > - clocks = <&clk 6>; > + clocks = <&clk NPCM7XX_CLK_UART>; > interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; > reg-shift = <2>; > status = "disabled"; > @@ -168,7 +169,7 @@ > serial2: serial@3000 { > compatible = "nuvoton,npcm750-uart"; > reg = <0x3000 0x1000>; > - clocks = <&clk 6>; > + clocks = <&clk NPCM7XX_CLK_UART>; > interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; > reg-shift = <2>; > status = "disabled"; > @@ -177,7 +178,7 @@ > serial3: serial@4000 { > compatible = "nuvoton,npcm750-uart"; > reg = <0x4000 0x1000>; > - clocks = <&clk 6>; > + clocks = <&clk NPCM7XX_CLK_UART>; > interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; > reg-shift = <2>; > status = "disabled"; > diff --git a/arch/arm/boot/dts/nuvoton-npcm750.dtsi b/arch/arm/boot/dts/nuvoton-npcm750.dtsi > index 6ac340533587..a37bb2294b8f 100644 > --- a/arch/arm/boot/dts/nuvoton-npcm750.dtsi > +++ b/arch/arm/boot/dts/nuvoton-npcm750.dtsi > @@ -17,7 +17,7 @@ > cpu@0 { > device_type = "cpu"; > compatible = "arm,cortex-a9"; > - clocks = <&clk 0>; > + clocks = <&clk NPCM7XX_CLK_CPU>; > clock-names = "clk_cpu"; > reg = <0>; > next-level-cache = <&l2>; > @@ -26,7 +26,7 @@ > cpu@1 { > device_type = "cpu"; > compatible = "arm,cortex-a9"; > - clocks = <&clk 0>; > + clocks = <&clk NPCM7XX_CLK_CPU>; > clock-names = "clk_cpu"; > reg = <1>; > next-level-cache = <&l2>; > @@ -38,7 +38,7 @@ > reg = <0x3fe600 0x20>; > interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | > IRQ_TYPE_LEVEL_HIGH)>; > - clocks = <&clk 5>; > + clocks = <&clk NPCM7XX_CLK_AHB>; > }; > }; > }; > -- > 2.22.0 > ^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH v5 2/3] arm: dts: modify NPCM7xx device tree timer register size 2020-09-16 12:55 [PATCH v5 0/3] arm: dts: add and modify device node in NPCM7xx device tree Tomer Maimon 2020-09-16 12:55 ` [PATCH v5 1/3] arm: dts: modify NPCM7xx device tree clock parameter Tomer Maimon @ 2020-09-16 12:55 ` Tomer Maimon 2020-09-16 13:21 ` Joel Stanley 2020-09-16 12:55 ` [PATCH v5 3/3] arm: dts: add new device nodes to NPCM750 device tree Tomer Maimon 2020-09-16 13:14 ` [PATCH v5 0/3] arm: dts: add and modify device node in NPCM7xx " Joel Stanley 3 siblings, 1 reply; 8+ messages in thread From: Tomer Maimon @ 2020-09-16 12:55 UTC (permalink / raw) To: robh+dt, mark.rutland, avifishman70, tali.perry1, venture, yuenn, benjaminfair, joel Cc: devicetree, linux-kernel, openbmc, tmaimon77 Modify NPCM7xx device tree timer register size from 0x50 to 0x1C. Signed-off-by: Tomer Maimon <tmaimon77@gmail.com> --- arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi b/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi index 16a28c5c4131..72e364054e72 100644 --- a/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi +++ b/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi @@ -120,7 +120,7 @@ timer0: timer@8000 { compatible = "nuvoton,npcm750-timer"; interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; - reg = <0x8000 0x50>; + reg = <0x8000 0x1C>; clocks = <&clk NPCM7XX_CLK_TIMER>; }; -- 2.22.0 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH v5 2/3] arm: dts: modify NPCM7xx device tree timer register size 2020-09-16 12:55 ` [PATCH v5 2/3] arm: dts: modify NPCM7xx device tree timer register size Tomer Maimon @ 2020-09-16 13:21 ` Joel Stanley 0 siblings, 0 replies; 8+ messages in thread From: Joel Stanley @ 2020-09-16 13:21 UTC (permalink / raw) To: Tomer Maimon Cc: Rob Herring, Mark Rutland, Avi Fishman, Tali Perry, Patrick Venture, Nancy Yuen, Benjamin Fair, devicetree, Linux Kernel Mailing List, OpenBMC Maillist On Wed, 16 Sep 2020 at 12:56, Tomer Maimon <tmaimon77@gmail.com> wrote: > > Modify NPCM7xx device tree timer register size > from 0x50 to 0x1C. We can see that you've done that from the patch. You should instead use the commit message to describe why you're making that change. Is it incorrect, or is there some other reason? > > Signed-off-by: Tomer Maimon <tmaimon77@gmail.com> Reviewed-by: Joel Stanley <joel@jms.id.au> > --- > arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi | 2 +- > 1 file changed, 1 insertion(+), 1 deletion(-) > > diff --git a/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi b/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi > index 16a28c5c4131..72e364054e72 100644 > --- a/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi > +++ b/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi > @@ -120,7 +120,7 @@ > timer0: timer@8000 { > compatible = "nuvoton,npcm750-timer"; > interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; > - reg = <0x8000 0x50>; > + reg = <0x8000 0x1C>; > clocks = <&clk NPCM7XX_CLK_TIMER>; > }; > > -- > 2.22.0 > ^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH v5 3/3] arm: dts: add new device nodes to NPCM750 device tree 2020-09-16 12:55 [PATCH v5 0/3] arm: dts: add and modify device node in NPCM7xx device tree Tomer Maimon 2020-09-16 12:55 ` [PATCH v5 1/3] arm: dts: modify NPCM7xx device tree clock parameter Tomer Maimon 2020-09-16 12:55 ` [PATCH v5 2/3] arm: dts: modify NPCM7xx device tree timer register size Tomer Maimon @ 2020-09-16 12:55 ` Tomer Maimon 2020-09-16 13:27 ` Joel Stanley 2020-09-16 13:14 ` [PATCH v5 0/3] arm: dts: add and modify device node in NPCM7xx " Joel Stanley 3 siblings, 1 reply; 8+ messages in thread From: Tomer Maimon @ 2020-09-16 12:55 UTC (permalink / raw) To: robh+dt, mark.rutland, avifishman70, tali.perry1, venture, yuenn, benjaminfair, joel Cc: devicetree, linux-kernel, openbmc, tmaimon77 Add the following new device nodes to NPCM750 and NPCM750 evolution board device tree: - NPCM7xx Pin controller and GPIO - NPCM7xx PWM and FAN. - NPCM7xx EHCI USB. - NPCM7xx KCS. - NPCM Reset. - NPCM Peripheral SPI. - NPCM FIU SPI. - NPCM HWRNG. - NPCM I2C. - STMicro STMMAC. Signed-off-by: Tomer Maimon <tmaimon77@gmail.com> --- arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi | 953 +++++++++++++++++- arch/arm/boot/dts/nuvoton-npcm750-evb.dts | 404 +++++++- .../boot/dts/nuvoton-npcm750-pincfg-evb.dtsi | 157 +++ arch/arm/boot/dts/nuvoton-npcm750.dtsi | 18 + 4 files changed, 1508 insertions(+), 24 deletions(-) create mode 100644 arch/arm/boot/dts/nuvoton-npcm750-pincfg-evb.dtsi diff --git a/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi b/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi index 72e364054e72..7d4be1ded470 100644 --- a/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi +++ b/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi @@ -4,12 +4,18 @@ #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/clock/nuvoton,npcm7xx-clock.h> +#include <dt-bindings/reset/nuvoton,npcm7xx-reset.h> / { #address-cells = <1>; #size-cells = <1>; interrupt-parent = <&gic>; + memory { + device_type = "memory"; + reg = <0x0 0x40000000>; + }; + /* external reference clock */ clk_refclk: clk_refclk { compatible = "fixed-clock"; @@ -64,12 +70,6 @@ interrupt-parent = <&gic>; ranges = <0x0 0xf0000000 0x00900000>; - gcr: gcr@800000 { - compatible = "nuvoton,npcm750-gcr", "syscon", - "simple-mfd"; - reg = <0x800000 0x1000>; - }; - scu: scu@3fe000 { compatible = "arm,cortex-a9-scu"; reg = <0x3fe000 0x1000>; @@ -92,6 +92,16 @@ reg = <0x3ff000 0x1000>, <0x3fe100 0x100>; }; + + gcr: gcr@800000 { + compatible = "nuvoton,npcm750-gcr", "syscon", "simple-mfd"; + reg = <0x800000 0x1000>; + }; + + rst: rst@801000 { + compatible = "nuvoton,npcm750-rst", "syscon", "simple-mfd"; + reg = <0x801000 0x6C>; + }; }; ahb { @@ -101,6 +111,12 @@ interrupt-parent = <&gic>; ranges; + rstc: rstc@f0801000 { + compatible = "nuvoton,npcm750-reset"; + reg = <0xf0801000 0x70>; + #reset-cells = <2>; + }; + clk: clock-controller@f0801000 { compatible = "nuvoton,npcm750-clk", "syscon"; #clock-cells = <1>; @@ -110,6 +126,63 @@ clocks = <&clk_refclk>, <&clk_sysbypck>, <&clk_mcbypck>; }; + gmac0: eth@f0802000 { + device_type = "network"; + compatible = "snps,dwmac"; + reg = <0xf0802000 0x2000>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + ethernet = <0>; + clocks = <&clk_rg1refck>, <&clk NPCM7XX_CLK_AHB>; + clock-names = "stmmaceth", "clk_gmac"; + pinctrl-names = "default"; + pinctrl-0 = <&rg1_pins + &rg1mdio_pins>; + status = "disabled"; + }; + + ehci1:usb@f0806000 { + compatible = "nuvoton,npcm750-ehci"; + reg = <0xf0806000 0x1000>; + interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + fiu0: spi@fb000000 { + compatible = "nuvoton,npcm750-fiu"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0xfb000000 0x1000>, <0x80000000 0x10000000>; + reg-names = "control", "memory"; + clocks = <&clk NPCM7XX_CLK_SPI0>; + clock-names = "clk_spi0"; + status = "disabled"; + }; + + fiu3: spi@c0000000 { + compatible = "nuvoton,npcm750-fiu"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0xc0000000 0x1000>, <0xA0000000 0x20000000>; + reg-names = "control", "memory"; + clocks = <&clk NPCM7XX_CLK_SPI3>; + clock-names = "clk_spi3"; + pinctrl-names = "default"; + pinctrl-0 = <&spi3_pins>; + status = "disabled"; + }; + + fiux: spi@fb001000 { + compatible = "nuvoton,npcm750-fiu"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0xfb001000 0x1000>, <0xf8000000 0x2000000>; + reg-names = "control", "memory"; + clocks = <&clk NPCM7XX_CLK_SPIX>; + clock-names = "clk_spix"; + status = "disabled"; + }; + apb { #address-cells = <1>; #size-cells = <1>; @@ -117,6 +190,69 @@ interrupt-parent = <&gic>; ranges = <0x0 0xf0000000 0x00300000>; + lpc_kcs: lpc_kcs@7000 { + compatible = "nuvoton,npcm750-lpc-kcs", + "simple-mfd", "syscon"; + reg = <0x7000 0x40>; + reg-io-width = <1>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x7000 0x40>; + + kcs1: kcs1@0 { + compatible = "nuvoton,npcm750-kcs-bmc"; + reg = <0x0 0x40>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + kcs_chan = <1>; + status = "disabled"; + }; + + kcs2: kcs2@0 { + compatible = "nuvoton,npcm750-kcs-bmc"; + reg = <0x0 0x40>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + kcs_chan = <2>; + status = "disabled"; + }; + + kcs3: kcs3@0 { + compatible = "nuvoton,npcm750-kcs-bmc"; + reg = <0x0 0x40>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + kcs_chan = <3>; + status = "disabled"; + }; + }; + + spi0: spi@200000 { + compatible = "nuvoton,npcm750-pspi"; + reg = <0x200000 0x1000>; + pinctrl-names = "default"; + pinctrl-0 = <&pspi1_pins>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk NPCM7XX_CLK_APB5>; + clock-names = "clk_apb5"; + resets = <&rstc NPCM7XX_RESET_IPSRST2 NPCM7XX_RESET_PSPI1>; + status = "disabled"; + }; + + spi1: spi@201000 { + compatible = "nuvoton,npcm750-pspi"; + reg = <0x201000 0x1000>; + pinctrl-names = "default"; + pinctrl-0 = <&pspi2_pins>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk NPCM7XX_CLK_APB5>; + clock-names = "clk_apb5"; + resets = <&rstc NPCM7XX_RESET_IPSRST2 NPCM7XX_RESET_PSPI2>; + status = "disabled"; + }; + timer0: timer@8000 { compatible = "nuvoton,npcm750-timer"; interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; @@ -183,6 +319,811 @@ reg-shift = <2>; status = "disabled"; }; + + rng: rng@b000 { + compatible = "nuvoton,npcm750-rng"; + reg = <0xb000 0x8>; + status = "disabled"; + }; + + adc: adc@c000 { + compatible = "nuvoton,npcm750-adc"; + reg = <0xc000 0x8>; + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk NPCM7XX_CLK_ADC>; + resets = <&rstc NPCM7XX_RESET_IPSRST1 NPCM7XX_RESET_ADC>; + status = "disabled"; + }; + + pwm_fan:pwm-fan-controller@103000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "nuvoton,npcm750-pwm-fan"; + reg = <0x103000 0x2000>, <0x180000 0x8000>; + reg-names = "pwm", "fan"; + clocks = <&clk NPCM7XX_CLK_APB3>, + <&clk NPCM7XX_CLK_APB4>; + clock-names = "pwm","fan"; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_pins &pwm1_pins + &pwm2_pins &pwm3_pins + &pwm4_pins &pwm5_pins + &pwm6_pins &pwm7_pins + &fanin0_pins &fanin1_pins + &fanin2_pins &fanin3_pins + &fanin4_pins &fanin5_pins + &fanin6_pins &fanin7_pins + &fanin8_pins &fanin9_pins + &fanin10_pins &fanin11_pins + &fanin12_pins &fanin13_pins + &fanin14_pins &fanin15_pins>; + status = "disabled"; + }; + + i2c0: i2c@80000 { + reg = <0x80000 0x1000>; + compatible = "nuvoton,npcm750-i2c"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clk NPCM7XX_CLK_APB2>; + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&smb0_pins>; + status = "disabled"; + }; + + i2c1: i2c@81000 { + reg = <0x81000 0x1000>; + compatible = "nuvoton,npcm750-i2c"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clk NPCM7XX_CLK_APB2>; + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&smb1_pins>; + status = "disabled"; + }; + + i2c2: i2c@82000 { + reg = <0x82000 0x1000>; + compatible = "nuvoton,npcm750-i2c"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clk NPCM7XX_CLK_APB2>; + interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&smb2_pins>; + status = "disabled"; + }; + + i2c3: i2c@83000 { + reg = <0x83000 0x1000>; + compatible = "nuvoton,npcm750-i2c"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clk NPCM7XX_CLK_APB2>; + interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&smb3_pins>; + status = "disabled"; + }; + + i2c4: i2c@84000 { + reg = <0x84000 0x1000>; + compatible = "nuvoton,npcm750-i2c"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clk NPCM7XX_CLK_APB2>; + interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&smb4_pins>; + status = "disabled"; + }; + + i2c5: i2c@85000 { + reg = <0x85000 0x1000>; + compatible = "nuvoton,npcm750-i2c"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clk NPCM7XX_CLK_APB2>; + interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&smb5_pins>; + status = "disabled"; + }; + + i2c6: i2c@86000 { + reg = <0x86000 0x1000>; + compatible = "nuvoton,npcm750-i2c"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clk NPCM7XX_CLK_APB2>; + interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&smb6_pins>; + status = "disabled"; + }; + + i2c7: i2c@87000 { + reg = <0x87000 0x1000>; + compatible = "nuvoton,npcm750-i2c"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clk NPCM7XX_CLK_APB2>; + interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&smb7_pins>; + status = "disabled"; + }; + + i2c8: i2c@88000 { + reg = <0x88000 0x1000>; + compatible = "nuvoton,npcm750-i2c"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clk NPCM7XX_CLK_APB2>; + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&smb8_pins>; + status = "disabled"; + }; + + i2c9: i2c@89000 { + reg = <0x89000 0x1000>; + compatible = "nuvoton,npcm750-i2c"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clk NPCM7XX_CLK_APB2>; + interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&smb9_pins>; + status = "disabled"; + }; + + i2c10: i2c@8a000 { + reg = <0x8a000 0x1000>; + compatible = "nuvoton,npcm750-i2c"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clk NPCM7XX_CLK_APB2>; + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&smb10_pins>; + status = "disabled"; + }; + + i2c11: i2c@8b000 { + reg = <0x8b000 0x1000>; + compatible = "nuvoton,npcm750-i2c"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clk NPCM7XX_CLK_APB2>; + interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&smb11_pins>; + status = "disabled"; + }; + + i2c12: i2c@8c000 { + reg = <0x8c000 0x1000>; + compatible = "nuvoton,npcm750-i2c"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clk NPCM7XX_CLK_APB2>; + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&smb12_pins>; + status = "disabled"; + }; + + i2c13: i2c@8d000 { + reg = <0x8d000 0x1000>; + compatible = "nuvoton,npcm750-i2c"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clk NPCM7XX_CLK_APB2>; + interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&smb13_pins>; + status = "disabled"; + }; + + i2c14: i2c@8e000 { + reg = <0x8e000 0x1000>; + compatible = "nuvoton,npcm750-i2c"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clk NPCM7XX_CLK_APB2>; + interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&smb14_pins>; + status = "disabled"; + }; + + i2c15: i2c@8f000 { + reg = <0x8f000 0x1000>; + compatible = "nuvoton,npcm750-i2c"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clk NPCM7XX_CLK_APB2>; + interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&smb15_pins>; + status = "disabled"; + }; + }; + }; + + pinctrl: pinctrl@f0800000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "nuvoton,npcm750-pinctrl", "syscon", "simple-mfd"; + ranges = <0 0xf0010000 0x8000>; + status = "okay"; + gpio0: gpio@f0010000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x0 0x80>; + interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>; + gpio-ranges = <&pinctrl 0 0 32>; + }; + gpio1: gpio@f0011000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x1000 0x80>; + interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; + gpio-ranges = <&pinctrl 0 32 32>; + }; + gpio2: gpio@f0012000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x2000 0x80>; + interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; + gpio-ranges = <&pinctrl 0 64 32>; + }; + gpio3: gpio@f0013000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x3000 0x80>; + interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; + gpio-ranges = <&pinctrl 0 96 32>; + }; + gpio4: gpio@f0014000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x4000 0x80>; + interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; + gpio-ranges = <&pinctrl 0 128 32>; + }; + gpio5: gpio@f0015000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x5000 0x80>; + interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; + gpio-ranges = <&pinctrl 0 160 32>; + }; + gpio6: gpio@f0016000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x6000 0x80>; + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>; + gpio-ranges = <&pinctrl 0 192 32>; + }; + gpio7: gpio@f0017000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x7000 0x80>; + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; + gpio-ranges = <&pinctrl 0 224 32>; + }; + + iox1_pins: iox1-pins { + groups = "iox1"; + function = "iox1"; + }; + iox2_pins: iox2-pins { + groups = "iox2"; + function = "iox2"; + }; + smb1d_pins: smb1d-pins { + groups = "smb1d"; + function = "smb1d"; + }; + smb2d_pins: smb2d-pins { + groups = "smb2d"; + function = "smb2d"; + }; + lkgpo1_pins: lkgpo1-pins { + groups = "lkgpo1"; + function = "lkgpo1"; + }; + lkgpo2_pins: lkgpo2-pins { + groups = "lkgpo2"; + function = "lkgpo2"; + }; + ioxh_pins: ioxh-pins { + groups = "ioxh"; + function = "ioxh"; + }; + gspi_pins: gspi-pins { + groups = "gspi"; + function = "gspi"; + }; + smb5b_pins: smb5b-pins { + groups = "smb5b"; + function = "smb5b"; + }; + smb5c_pins: smb5c-pins { + groups = "smb5c"; + function = "smb5c"; + }; + lkgpo0_pins: lkgpo0-pins { + groups = "lkgpo0"; + function = "lkgpo0"; + }; + pspi2_pins: pspi2-pins { + groups = "pspi2"; + function = "pspi2"; + }; + smb4den_pins: smb4den-pins { + groups = "smb4den"; + function = "smb4den"; + }; + smb4b_pins: smb4b-pins { + groups = "smb4b"; + function = "smb4b"; + }; + smb4c_pins: smb4c-pins { + groups = "smb4c"; + function = "smb4c"; + }; + smb15_pins: smb15-pins { + groups = "smb15"; + function = "smb15"; + }; + smb4d_pins: smb4d-pins { + groups = "smb4d"; + function = "smb4d"; + }; + smb14_pins: smb14-pins { + groups = "smb14"; + function = "smb14"; + }; + smb5_pins: smb5-pins { + groups = "smb5"; + function = "smb5"; + }; + smb4_pins: smb4-pins { + groups = "smb4"; + function = "smb4"; + }; + smb3_pins: smb3-pins { + groups = "smb3"; + function = "smb3"; + }; + spi0cs1_pins: spi0cs1-pins { + groups = "spi0cs1"; + function = "spi0cs1"; + }; + spi0cs2_pins: spi0cs2-pins { + groups = "spi0cs2"; + function = "spi0cs2"; + }; + spi0cs3_pins: spi0cs3-pins { + groups = "spi0cs3"; + function = "spi0cs3"; + }; + smb3c_pins: smb3c-pins { + groups = "smb3c"; + function = "smb3c"; + }; + smb3b_pins: smb3b-pins { + groups = "smb3b"; + function = "smb3b"; + }; + bmcuart0a_pins: bmcuart0a-pins { + groups = "bmcuart0a"; + function = "bmcuart0a"; + }; + uart1_pins: uart1-pins { + groups = "uart1"; + function = "uart1"; + }; + jtag2_pins: jtag2-pins { + groups = "jtag2"; + function = "jtag2"; + }; + bmcuart1_pins: bmcuart1-pins { + groups = "bmcuart1"; + function = "bmcuart1"; + }; + uart2_pins: uart2-pins { + groups = "uart2"; + function = "uart2"; + }; + bmcuart0b_pins: bmcuart0b-pins { + groups = "bmcuart0b"; + function = "bmcuart0b"; + }; + r1err_pins: r1err-pins { + groups = "r1err"; + function = "r1err"; + }; + r1md_pins: r1md-pins { + groups = "r1md"; + function = "r1md"; + }; + smb3d_pins: smb3d-pins { + groups = "smb3d"; + function = "smb3d"; + }; + fanin0_pins: fanin0-pins { + groups = "fanin0"; + function = "fanin0"; + }; + fanin1_pins: fanin1-pins { + groups = "fanin1"; + function = "fanin1"; + }; + fanin2_pins: fanin2-pins { + groups = "fanin2"; + function = "fanin2"; + }; + fanin3_pins: fanin3-pins { + groups = "fanin3"; + function = "fanin3"; + }; + fanin4_pins: fanin4-pins { + groups = "fanin4"; + function = "fanin4"; + }; + fanin5_pins: fanin5-pins { + groups = "fanin5"; + function = "fanin5"; + }; + fanin6_pins: fanin6-pins { + groups = "fanin6"; + function = "fanin6"; + }; + fanin7_pins: fanin7-pins { + groups = "fanin7"; + function = "fanin7"; + }; + fanin8_pins: fanin8-pins { + groups = "fanin8"; + function = "fanin8"; + }; + fanin9_pins: fanin9-pins { + groups = "fanin9"; + function = "fanin9"; + }; + fanin10_pins: fanin10-pins { + groups = "fanin10"; + function = "fanin10"; + }; + fanin11_pins: fanin11-pins { + groups = "fanin11"; + function = "fanin11"; + }; + fanin12_pins: fanin12-pins { + groups = "fanin12"; + function = "fanin12"; + }; + fanin13_pins: fanin13-pins { + groups = "fanin13"; + function = "fanin13"; + }; + fanin14_pins: fanin14-pins { + groups = "fanin14"; + function = "fanin14"; + }; + fanin15_pins: fanin15-pins { + groups = "fanin15"; + function = "fanin15"; + }; + pwm0_pins: pwm0-pins { + groups = "pwm0"; + function = "pwm0"; + }; + pwm1_pins: pwm1-pins { + groups = "pwm1"; + function = "pwm1"; + }; + pwm2_pins: pwm2-pins { + groups = "pwm2"; + function = "pwm2"; + }; + pwm3_pins: pwm3-pins { + groups = "pwm3"; + function = "pwm3"; + }; + r2_pins: r2-pins { + groups = "r2"; + function = "r2"; + }; + r2err_pins: r2err-pins { + groups = "r2err"; + function = "r2err"; + }; + r2md_pins: r2md-pins { + groups = "r2md"; + function = "r2md"; + }; + ga20kbc_pins: ga20kbc-pins { + groups = "ga20kbc"; + function = "ga20kbc"; + }; + smb5d_pins: smb5d-pins { + groups = "smb5d"; + function = "smb5d"; + }; + lpc_pins: lpc-pins { + groups = "lpc"; + function = "lpc"; + }; + espi_pins: espi-pins { + groups = "espi"; + function = "espi"; + }; + rg1_pins: rg1-pins { + groups = "rg1"; + function = "rg1"; + }; + rg1mdio_pins: rg1mdio-pins { + groups = "rg1mdio"; + function = "rg1mdio"; + }; + rg2_pins: rg2-pins { + groups = "rg2"; + function = "rg2"; + }; + ddr_pins: ddr-pins { + groups = "ddr"; + function = "ddr"; + }; + smb0_pins: smb0-pins { + groups = "smb0"; + function = "smb0"; + }; + smb1_pins: smb1-pins { + groups = "smb1"; + function = "smb1"; + }; + smb2_pins: smb2-pins { + groups = "smb2"; + function = "smb2"; + }; + smb2c_pins: smb2c-pins { + groups = "smb2c"; + function = "smb2c"; + }; + smb2b_pins: smb2b-pins { + groups = "smb2b"; + function = "smb2b"; + }; + smb1c_pins: smb1c-pins { + groups = "smb1c"; + function = "smb1c"; + }; + smb1b_pins: smb1b-pins { + groups = "smb1b"; + function = "smb1b"; + }; + smb8_pins: smb8-pins { + groups = "smb8"; + function = "smb8"; + }; + smb9_pins: smb9-pins { + groups = "smb9"; + function = "smb9"; + }; + smb10_pins: smb10-pins { + groups = "smb10"; + function = "smb10"; + }; + smb11_pins: smb11-pins { + groups = "smb11"; + function = "smb11"; + }; + sd1_pins: sd1-pins { + groups = "sd1"; + function = "sd1"; + }; + sd1pwr_pins: sd1pwr-pins { + groups = "sd1pwr"; + function = "sd1pwr"; + }; + pwm4_pins: pwm4-pins { + groups = "pwm4"; + function = "pwm4"; + }; + pwm5_pins: pwm5-pins { + groups = "pwm5"; + function = "pwm5"; + }; + pwm6_pins: pwm6-pins { + groups = "pwm6"; + function = "pwm6"; + }; + pwm7_pins: pwm7-pins { + groups = "pwm7"; + function = "pwm7"; + }; + mmc8_pins: mmc8-pins { + groups = "mmc8"; + function = "mmc8"; + }; + mmc_pins: mmc-pins { + groups = "mmc"; + function = "mmc"; + }; + mmcwp_pins: mmcwp-pins { + groups = "mmcwp"; + function = "mmcwp"; + }; + mmccd_pins: mmccd-pins { + groups = "mmccd"; + function = "mmccd"; + }; + mmcrst_pins: mmcrst-pins { + groups = "mmcrst"; + function = "mmcrst"; + }; + clkout_pins: clkout-pins { + groups = "clkout"; + function = "clkout"; + }; + serirq_pins: serirq-pins { + groups = "serirq"; + function = "serirq"; + }; + lpcclk_pins: lpcclk-pins { + groups = "lpcclk"; + function = "lpcclk"; + }; + scipme_pins: scipme-pins { + groups = "scipme"; + function = "scipme"; + }; + sci_pins: sci-pins { + groups = "sci"; + function = "sci"; + }; + smb6_pins: smb6-pins { + groups = "smb6"; + function = "smb6"; + }; + smb7_pins: smb7-pins { + groups = "smb7"; + function = "smb7"; + }; + pspi1_pins: pspi1-pins { + groups = "pspi1"; + function = "pspi1"; + }; + faninx_pins: faninx-pins { + groups = "faninx"; + function = "faninx"; + }; + r1_pins: r1-pins { + groups = "r1"; + function = "r1"; + }; + spi3_pins: spi3-pins { + groups = "spi3"; + function = "spi3"; + }; + spi3cs1_pins: spi3cs1-pins { + groups = "spi3cs1"; + function = "spi3cs1"; + }; + spi3quad_pins: spi3quad-pins { + groups = "spi3quad"; + function = "spi3quad"; + }; + spi3cs2_pins: spi3cs2-pins { + groups = "spi3cs2"; + function = "spi3cs2"; + }; + spi3cs3_pins: spi3cs3-pins { + groups = "spi3cs3"; + function = "spi3cs3"; + }; + nprd_smi_pins: nprd-smi-pins { + groups = "nprd_smi"; + function = "nprd_smi"; + }; + smb0b_pins: smb0b-pins { + groups = "smb0b"; + function = "smb0b"; + }; + smb0c_pins: smb0c-pins { + groups = "smb0c"; + function = "smb0c"; + }; + smb0den_pins: smb0den-pins { + groups = "smb0den"; + function = "smb0den"; + }; + smb0d_pins: smb0d-pins { + groups = "smb0d"; + function = "smb0d"; + }; + ddc_pins: ddc-pins { + groups = "ddc"; + function = "ddc"; + }; + rg2mdio_pins: rg2mdio-pins { + groups = "rg2mdio"; + function = "rg2mdio"; + }; + wdog1_pins: wdog1-pins { + groups = "wdog1"; + function = "wdog1"; + }; + wdog2_pins: wdog2-pins { + groups = "wdog2"; + function = "wdog2"; + }; + smb12_pins: smb12-pins { + groups = "smb12"; + function = "smb12"; + }; + smb13_pins: smb13-pins { + groups = "smb13"; + function = "smb13"; + }; + spix_pins: spix-pins { + groups = "spix"; + function = "spix"; + }; + spixcs1_pins: spixcs1-pins { + groups = "spixcs1"; + function = "spixcs1"; + }; + clkreq_pins: clkreq-pins { + groups = "clkreq"; + function = "clkreq"; + }; + hgpio0_pins: hgpio0-pins { + groups = "hgpio0"; + function = "hgpio0"; + }; + hgpio1_pins: hgpio1-pins { + groups = "hgpio1"; + function = "hgpio1"; + }; + hgpio2_pins: hgpio2-pins { + groups = "hgpio2"; + function = "hgpio2"; + }; + hgpio3_pins: hgpio3-pins { + groups = "hgpio3"; + function = "hgpio3"; + }; + hgpio4_pins: hgpio4-pins { + groups = "hgpio4"; + function = "hgpio4"; + }; + hgpio5_pins: hgpio5-pins { + groups = "hgpio5"; + function = "hgpio5"; + }; + hgpio6_pins: hgpio6-pins { + groups = "hgpio6"; + function = "hgpio6"; + }; + hgpio7_pins: hgpio7-pins { + groups = "hgpio7"; + function = "hgpio7"; }; }; }; diff --git a/arch/arm/boot/dts/nuvoton-npcm750-evb.dts b/arch/arm/boot/dts/nuvoton-npcm750-evb.dts index 15f744f1beea..0af79573ab28 100644 --- a/arch/arm/boot/dts/nuvoton-npcm750-evb.dts +++ b/arch/arm/boot/dts/nuvoton-npcm750-evb.dts @@ -4,36 +4,404 @@ /dts-v1/; #include "nuvoton-npcm750.dtsi" +#include "dt-bindings/gpio/gpio.h" +#include "nuvoton-npcm750-pincfg-evb.dtsi" / { model = "Nuvoton npcm750 Development Board (Device Tree)"; compatible = "nuvoton,npcm750"; + aliases { + ethernet2 = &gmac0; + ethernet3 = &gmac1; + serial0 = &serial0; + serial1 = &serial1; + serial2 = &serial2; + serial3 = &serial3; + i2c0 = &i2c0; + i2c1 = &i2c1; + i2c2 = &i2c2; + i2c3 = &i2c3; + i2c4 = &i2c4; + i2c5 = &i2c5; + i2c6 = &i2c6; + i2c7 = &i2c7; + i2c8 = &i2c8; + i2c9 = &i2c9; + i2c10 = &i2c10; + i2c11 = &i2c11; + i2c12 = &i2c12; + i2c13 = &i2c13; + i2c14 = &i2c14; + i2c15 = &i2c15; + spi0 = &spi0; + spi1 = &spi1; + fiu0 = &fiu0; + fiu1 = &fiu3; + fiu2 = &fiux; + }; + chosen { stdout-path = &serial3; }; - memory { - reg = <0 0x40000000>; - }; -}; + ahb { + gmac0: eth@f0802000 { + phy-mode = "rgmii-id"; + status = "okay"; + }; -&watchdog1 { - status = "okay"; -}; + gmac1: eth@f0804000 { + phy-mode = "rgmii-id"; + status = "okay"; + }; -&serial0 { - status = "okay"; -}; + ehci1: usb@f0806000 { + status = "okay"; + }; -&serial1 { - status = "okay"; -}; + fiu0: spi@fb000000 { + status = "okay"; + spi-nor@0 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + spi-rx-bus-width = <2>; + reg = <0>; + spi-max-frequency = <5000000>; + partitions@80000000 { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + bbuboot1@0 { + label = "bb-uboot-1"; + reg = <0x0000000 0x80000>; + read-only; + }; + bbuboot2@80000 { + label = "bb-uboot-2"; + reg = <0x0080000 0x80000>; + read-only; + }; + envparam@100000 { + label = "env-param"; + reg = <0x0100000 0x40000>; + read-only; + }; + spare@140000 { + label = "spare"; + reg = <0x0140000 0xC0000>; + }; + kernel@200000 { + label = "kernel"; + reg = <0x0200000 0x400000>; + }; + rootfs@600000 { + label = "rootfs"; + reg = <0x0600000 0x700000>; + }; + spare1@D00000 { + label = "spare1"; + reg = <0x0D00000 0x200000>; + }; + spare2@0F00000 { + label = "spare2"; + reg = <0x0F00000 0x200000>; + }; + spare3@1100000 { + label = "spare3"; + reg = <0x1100000 0x200000>; + }; + spare4@1300000 { + label = "spare4"; + reg = <0x1300000 0x0>; + }; + }; + }; + }; -&serial2 { - status = "okay"; -}; + fiu3: spi@c0000000 { + pinctrl-0 = <&spi3_pins>, <&spi3quad_pins>; + status = "okay"; + spi-nor@0 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + spi-rx-bus-width = <2>; + reg = <0>; + spi-max-frequency = <5000000>; + partitions@A0000000 { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + system1@0 { + label = "spi3-system1"; + reg = <0x0 0x0>; + }; + }; + }; + }; + + fiux: spi@fb001000 { + spix-mode; + }; + + apb { + + watchdog1: watchdog@901C { + status = "okay"; + }; + + rng: rng@b000 { + status = "okay"; + }; + + serial0: serial@1000 { + status = "okay"; + }; + + serial1: serial@2000 { + status = "okay"; + }; + + serial2: serial@3000 { + status = "okay"; + }; + + serial3: serial@4000 { + status = "okay"; + }; + + adc: adc@c000 { + status = "okay"; + }; + + otp:otp@189000 { + status = "okay"; + }; + + lpc_kcs: lpc_kcs@7000 { + kcs1: kcs1@0 { + status = "okay"; + }; -&serial3 { - status = "okay"; + kcs2: kcs2@0 { + status = "okay"; + }; + + kcs3: kcs3@0 { + status = "okay"; + }; + }; + + /* lm75 on SVB */ + i2c0: i2c@80000 { + clock-frequency = <100000>; + status = "okay"; + lm75@48 { + compatible = "lm75"; + reg = <0x48>; + status = "okay"; + }; + }; + + /* lm75 on EB */ + i2c1: i2c@81000 { + clock-frequency = <100000>; + status = "okay"; + lm75@48 { + compatible = "lm75"; + reg = <0x48>; + status = "okay"; + }; + }; + + /* tmp100 on EB */ + i2c2: i2c@82000 { + clock-frequency = <100000>; + status = "okay"; + tmp100@48 { + compatible = "tmp100"; + reg = <0x48>; + status = "okay"; + }; + }; + + i2c3: i2c@83000 { + clock-frequency = <100000>; + status = "okay"; + }; + + i2c5: i2c@85000 { + clock-frequency = <100000>; + status = "okay"; + }; + + /* tmp100 on SVB */ + i2c6: i2c@86000 { + clock-frequency = <100000>; + status = "okay"; + tmp100@48 { + compatible = "tmp100"; + reg = <0x48>; + status = "okay"; + }; + }; + + i2c7: i2c@87000 { + clock-frequency = <100000>; + status = "okay"; + }; + + i2c8: i2c@88000 { + clock-frequency = <100000>; + status = "okay"; + }; + + i2c9: i2c@89000 { + clock-frequency = <100000>; + status = "okay"; + }; + + i2c10: i2c@8a000 { + clock-frequency = <100000>; + status = "okay"; + }; + + i2c11: i2c@8b000 { + clock-frequency = <100000>; + status = "okay"; + }; + + i2c14: i2c@8e000 { + clock-frequency = <100000>; + status = "okay"; + }; + + pwm_fan:pwm-fan-controller@103000 { + status = "okay"; + fan@0 { + reg = <0x00>; + fan-tach-ch = /bits/ 8 <0x00 0x01>; + cooling-levels = <127 255>; + }; + fan@1 { + reg = <0x01>; + fan-tach-ch = /bits/ 8 <0x02 0x03>; + cooling-levels = /bits/ 8 <127 255>; + }; + fan@2 { + reg = <0x02>; + fan-tach-ch = /bits/ 8 <0x04 0x05>; + cooling-levels = /bits/ 8 <127 255>; + }; + fan@3 { + reg = <0x03>; + fan-tach-ch = /bits/ 8 <0x06 0x07>; + cooling-levels = /bits/ 8 <127 255>; + }; + fan@4 { + reg = <0x04>; + fan-tach-ch = /bits/ 8 <0x08 0x09>; + cooling-levels = /bits/ 8 <127 255>; + }; + fan@5 { + reg = <0x05>; + fan-tach-ch = /bits/ 8 <0x0A 0x0B>; + cooling-levels = /bits/ 8 <127 255>; + }; + fan@6 { + reg = <0x06>; + fan-tach-ch = /bits/ 8 <0x0C 0x0D>; + cooling-levels = /bits/ 8 <127 255>; + }; + fan@7 { + reg = <0x07>; + fan-tach-ch = /bits/ 8 <0x0E 0x0F>; + cooling-levels = /bits/ 8 <127 255>; + }; + }; + + spi0: spi@200000 { + cs-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>; + status = "okay"; + Flash@0 { + compatible = "winbond,w25q128", + "jedec,spi-nor"; + reg = <0x0>; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <5000000>; + partition@0 { + label = "spi0_spare1"; + reg = <0x0000000 0x800000>; + }; + partition@1 { + label = "spi0_spare2"; + reg = <0x800000 0x0>; + }; + }; + }; + + spi1: spi@201000 { + cs-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; + status = "okay"; + Flash@0 { + compatible = "winbond,w25q128fw", + "jedec,spi-nor"; + reg = <0x0>; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <5000000>; + partition@0 { + label = "spi1_spare1"; + reg = <0x0000000 0x800000>; + }; + partition@1 { + label = "spi1_spare2"; + reg = <0x800000 0x0>; + }; + }; + }; + }; + }; + + pinctrl: pinctrl@f0800000 { + pinctrl-names = "default"; + pinctrl-0 = < &iox1_pins + &pin8_input + &pin9_output_high + &pin10_input + &pin11_output_high + &pin16_input + &pin24_output_high + &pin25_output_low + &pin32_output_high + &jtag2_pins + &pin61_output_high + &pin62_output_high + &pin63_output_high + &lpc_pins + &pin160_input + &pin162_input + &pin168_input + &pin169_input + &pin170_input + &pin187_output_high + &pin190_input + &pin191_output_high + &pin192_output_high + &pin197_output_low + &ddc_pins + &pin218_input + &pin219_output_low + &pin220_output_low + &pin221_output_high + &pin222_input + &pin223_output_low + &spix_pins + &pin228_output_low + &pin231_output_high + &pin255_input>; + }; }; diff --git a/arch/arm/boot/dts/nuvoton-npcm750-pincfg-evb.dtsi b/arch/arm/boot/dts/nuvoton-npcm750-pincfg-evb.dtsi new file mode 100644 index 000000000000..edb4190826e6 --- /dev/null +++ b/arch/arm/boot/dts/nuvoton-npcm750-pincfg-evb.dtsi @@ -0,0 +1,157 @@ +// SPDX-License-Identifier: GPL-2.0 +// Copyright (c) 2018 Nuvoton Technology tomer.maimon@nuvoton.com + +/ { + pinctrl: pinctrl@f0800000 { + pin8_input: pin8-input { + pins = "GPIO8/LKGPO1"; + bias-disable; + input-enable; + }; + pin9_output_high: pin9-output-high { + pins = "GPIO9/LKGPO2"; + bias-disable; + output-high; + }; + pin10_input: pin10-input { + pins = "GPIO10/IOXHLD"; + bias-disable; + input-enable; + }; + pin11_output_high: pin11-output-high { + pins = "GPIO11/IOXHCK"; + bias-disable; + output-high; + }; + pin16_input: pin16-input { + pins = "GPIO16/LKGPO0"; + bias-disable; + input-enable; + }; + pin24_output_high: pin24-output-high { + pins = "GPIO24/IOXHDO"; + bias-disable; + output-high; + }; + pin25_output_low: pin25-output-low { + pins = "GPIO25/IOXHDI"; + bias-disable; + output-low; + }; + pin32_output_high: pin32-output-high { + pins = "GPIO32/nSPI0CS1"; + bias-disable; + output-high; + }; + pin61_output_high: pin61-output-high { + pins = "GPO61/nDTR1_BOUT1/STRAP6"; + bias-disable; + output-high; + }; + pin62_output_high: pin62-output-high { + pins = "GPO62/nRTST1/STRAP5"; + bias-disable; + output-high; + }; + pin63_output_high: pin63-output-high { + pins = "GPO63/TXD1/STRAP4"; + bias-disable; + output-high; + }; + pin160_input: pin160-input { + pins = "GPIO160/CLKOUT/RNGOSCOUT"; + bias-disable; + input-enable; + }; + pin162_input: pin162-input { + pins = "GPIO162/SERIRQ"; + bias-disable; + input-enable; + }; + pin168_input: pin168-input { + pins = "GPIO168/nCLKRUN/nESPIALERT"; + bias-disable; + input-enable; + }; + pin169_input: pin169-input { + pins = "GPIO169/nSCIPME"; + bias-disable; + input-enable; + }; + pin170_input: pin170-input { + pins = "GPIO170/nSMI"; + bias-disable; + input-enable; + }; + pin187_output_high: pin187-output-high { + pins = "GPIO187/nSPI3CS1"; + bias-disable; + output-high; + }; + pin190_input: pin190-input { + pins = "GPIO190/nPRD_SMI"; + bias-disable; + input-enable; + }; + pin191_output_high: pin191-output-high { + pins = "GPIO191"; + bias-disable; + output-high; + }; + pin192_output_high: pin192-output-high { + pins = "GPIO192"; + bias-disable; + output-high; + }; + pin197_output_low: pin197-output-low { + pins = "GPIO197/SMB0DEN"; + bias-disable; + output-low; + }; + pin218_input: pin218-input { + pins = "GPIO218/nWDO1"; + bias-disable; + input-enable; + }; + pin219_output_low: pin219-output-low { + pins = "GPIO219/nWDO2"; + bias-disable; + output-low; + }; + pin220_output_low: pin220-output-low { + pins = "GPIO220/SMB12SCL"; + bias-disable; + output-low; + }; + pin221_output_high: pin221-output-high { + pins = "GPIO221/SMB12SDA"; + bias-disable; + output-high; + }; + pin222_input: pin222-input { + pins = "GPIO222/SMB13SCL"; + bias-disable; + input-enable; + }; + pin223_output_low: pin223-output-low { + pins = "GPIO223/SMB13SDA"; + bias-disable; + output-low; + }; + pin228_output_low: pin228-output-low { + pins = "GPIO228/nSPIXCS1"; + bias-disable; + output-low; + }; + pin231_output_high: pin231-output-high { + pins = "GPIO230/SPIXD3"; + bias-disable; + output-high; + }; + pin255_input: pin255-input { + pins = "GPI255/DACOSEL"; + bias-disable; + input-enable; + }; + }; +}; diff --git a/arch/arm/boot/dts/nuvoton-npcm750.dtsi b/arch/arm/boot/dts/nuvoton-npcm750.dtsi index a37bb2294b8f..13eee0fe5642 100644 --- a/arch/arm/boot/dts/nuvoton-npcm750.dtsi +++ b/arch/arm/boot/dts/nuvoton-npcm750.dtsi @@ -32,6 +32,7 @@ next-level-cache = <&l2>; }; }; + soc { timer@3fe600 { compatible = "arm,cortex-a9-twd-timer"; @@ -41,4 +42,21 @@ clocks = <&clk NPCM7XX_CLK_AHB>; }; }; + + ahb { + gmac1: eth@f0804000 { + device_type = "network"; + compatible = "snps,dwmac"; + reg = <0xf0804000 0x2000>; + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + ethernet = <1>; + clocks = <&clk_rg2refck>, <&clk NPCM7XX_CLK_AHB>; + clock-names = "stmmaceth", "clk_gmac"; + pinctrl-names = "default"; + pinctrl-0 = <&rg2_pins + &rg2mdio_pins>; + status = "disabled"; + }; + }; }; -- 2.22.0 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH v5 3/3] arm: dts: add new device nodes to NPCM750 device tree 2020-09-16 12:55 ` [PATCH v5 3/3] arm: dts: add new device nodes to NPCM750 device tree Tomer Maimon @ 2020-09-16 13:27 ` Joel Stanley 0 siblings, 0 replies; 8+ messages in thread From: Joel Stanley @ 2020-09-16 13:27 UTC (permalink / raw) To: Tomer Maimon Cc: Rob Herring, Mark Rutland, Avi Fishman, Tali Perry, Patrick Venture, Nancy Yuen, Benjamin Fair, devicetree, Linux Kernel Mailing List, OpenBMC Maillist On Wed, 16 Sep 2020 at 12:56, Tomer Maimon <tmaimon77@gmail.com> wrote: > > Add the following new device nodes to NPCM750 and > NPCM750 evolution board device tree: > > - NPCM7xx Pin controller and GPIO > - NPCM7xx PWM and FAN. > - NPCM7xx EHCI USB. > - NPCM7xx KCS. > - NPCM Reset. > - NPCM Peripheral SPI. > - NPCM FIU SPI. > - NPCM HWRNG. > - NPCM I2C. > - STMicro STMMAC. > > Signed-off-by: Tomer Maimon <tmaimon77@gmail.com> Some minor comments below. The important one is the memory node. > --- > arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi | 953 +++++++++++++++++- > arch/arm/boot/dts/nuvoton-npcm750-evb.dts | 404 +++++++- > .../boot/dts/nuvoton-npcm750-pincfg-evb.dtsi | 157 +++ > arch/arm/boot/dts/nuvoton-npcm750.dtsi | 18 + > 4 files changed, 1508 insertions(+), 24 deletions(-) > create mode 100644 arch/arm/boot/dts/nuvoton-npcm750-pincfg-evb.dtsi > > diff --git a/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi b/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi > index 72e364054e72..7d4be1ded470 100644 > --- a/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi > +++ b/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi > @@ -4,12 +4,18 @@ > > #include <dt-bindings/interrupt-controller/arm-gic.h> > #include <dt-bindings/clock/nuvoton,npcm7xx-clock.h> > +#include <dt-bindings/reset/nuvoton,npcm7xx-reset.h> > > / { > #address-cells = <1>; > #size-cells = <1>; > interrupt-parent = <&gic>; > > + memory { > + device_type = "memory"; > + reg = <0x0 0x40000000>; > + }; Do all npcm7xx parts have 1GB of RAM? If not, this would go in the board file (.dtb) instead of here. > + > /* external reference clock */ > clk_refclk: clk_refclk { > compatible = "fixed-clock"; > @@ -64,12 +70,6 @@ > interrupt-parent = <&gic>; > ranges = <0x0 0xf0000000 0x00900000>; > > - gcr: gcr@800000 { > - compatible = "nuvoton,npcm750-gcr", "syscon", > - "simple-mfd"; > - reg = <0x800000 0x1000>; > - }; > - > scu: scu@3fe000 { > compatible = "arm,cortex-a9-scu"; > reg = <0x3fe000 0x1000>; > @@ -92,6 +92,16 @@ > reg = <0x3ff000 0x1000>, > <0x3fe100 0x100>; > }; > + > + gcr: gcr@800000 { > + compatible = "nuvoton,npcm750-gcr", "syscon", "simple-mfd"; > + reg = <0x800000 0x1000>; > + }; > + > + rst: rst@801000 { > + compatible = "nuvoton,npcm750-rst", "syscon", "simple-mfd"; > + reg = <0x801000 0x6C>; > + }; > }; > > ahb { > @@ -101,6 +111,12 @@ > interrupt-parent = <&gic>; > ranges; > > + rstc: rstc@f0801000 { > + compatible = "nuvoton,npcm750-reset"; > + reg = <0xf0801000 0x70>; > + #reset-cells = <2>; > + }; > + > clk: clock-controller@f0801000 { > compatible = "nuvoton,npcm750-clk", "syscon"; > #clock-cells = <1>; > @@ -110,6 +126,63 @@ > clocks = <&clk_refclk>, <&clk_sysbypck>, <&clk_mcbypck>; > }; > > + gmac0: eth@f0802000 { > + device_type = "network"; > + compatible = "snps,dwmac"; > + reg = <0xf0802000 0x2000>; > + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "macirq"; > + ethernet = <0>; > + clocks = <&clk_rg1refck>, <&clk NPCM7XX_CLK_AHB>; > + clock-names = "stmmaceth", "clk_gmac"; > + pinctrl-names = "default"; > + pinctrl-0 = <&rg1_pins > + &rg1mdio_pins>; > + status = "disabled"; > + }; > + > + ehci1:usb@f0806000 { Normal style is to put a space after the : > + compatible = "nuvoton,npcm750-ehci"; > + reg = <0xf0806000 0x1000>; > + interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>; > + status = "disabled"; > + }; > + > + fiu0: spi@fb000000 { > + compatible = "nuvoton,npcm750-fiu"; > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0xfb000000 0x1000>, <0x80000000 0x10000000>; > + reg-names = "control", "memory"; > + clocks = <&clk NPCM7XX_CLK_SPI0>; > + clock-names = "clk_spi0"; > + status = "disabled"; > + }; > + > + fiu3: spi@c0000000 { > + compatible = "nuvoton,npcm750-fiu"; > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0xc0000000 0x1000>, <0xA0000000 0x20000000>; > + reg-names = "control", "memory"; > + clocks = <&clk NPCM7XX_CLK_SPI3>; > + clock-names = "clk_spi3"; > + pinctrl-names = "default"; > + pinctrl-0 = <&spi3_pins>; > + status = "disabled"; > + }; > + > + fiux: spi@fb001000 { > + compatible = "nuvoton,npcm750-fiu"; > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0xfb001000 0x1000>, <0xf8000000 0x2000000>; > + reg-names = "control", "memory"; > + clocks = <&clk NPCM7XX_CLK_SPIX>; > + clock-names = "clk_spix"; > + status = "disabled"; > + }; > + > apb { > #address-cells = <1>; > #size-cells = <1>; > @@ -117,6 +190,69 @@ > interrupt-parent = <&gic>; > ranges = <0x0 0xf0000000 0x00300000>; > > + lpc_kcs: lpc_kcs@7000 { > + compatible = "nuvoton,npcm750-lpc-kcs", > + "simple-mfd", "syscon"; Put this one one line. > + reg = <0x7000 0x40>; > + reg-io-width = <1>; > + > + #address-cells = <1>; > + #size-cells = <1>; > + ranges = <0x0 0x7000 0x40>; > + > + kcs1: kcs1@0 { > + compatible = "nuvoton,npcm750-kcs-bmc"; > + reg = <0x0 0x40>; > + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; > + kcs_chan = <1>; > + status = "disabled"; > + }; > + > + kcs2: kcs2@0 { > + compatible = "nuvoton,npcm750-kcs-bmc"; > + reg = <0x0 0x40>; > + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; > + kcs_chan = <2>; > + status = "disabled"; > + }; > + > + kcs3: kcs3@0 { > + compatible = "nuvoton,npcm750-kcs-bmc"; > + reg = <0x0 0x40>; > + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; > + kcs_chan = <3>; > + status = "disabled"; > + }; > + }; > + > + spi0: spi@200000 { > + compatible = "nuvoton,npcm750-pspi"; > + reg = <0x200000 0x1000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pspi1_pins>; > + #address-cells = <1>; > + #size-cells = <0>; > + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clk NPCM7XX_CLK_APB5>; > + clock-names = "clk_apb5"; > + resets = <&rstc NPCM7XX_RESET_IPSRST2 NPCM7XX_RESET_PSPI1>; > + status = "disabled"; > + }; > + > + spi1: spi@201000 { > + compatible = "nuvoton,npcm750-pspi"; > + reg = <0x201000 0x1000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pspi2_pins>; > + #address-cells = <1>; > + #size-cells = <0>; > + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clk NPCM7XX_CLK_APB5>; > + clock-names = "clk_apb5"; > + resets = <&rstc NPCM7XX_RESET_IPSRST2 NPCM7XX_RESET_PSPI2>; > + status = "disabled"; > + }; > + > timer0: timer@8000 { > compatible = "nuvoton,npcm750-timer"; > interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; > @@ -183,6 +319,811 @@ > reg-shift = <2>; > status = "disabled"; > }; > + > + rng: rng@b000 { > + compatible = "nuvoton,npcm750-rng"; > + reg = <0xb000 0x8>; > + status = "disabled"; > + }; > + > + adc: adc@c000 { > + compatible = "nuvoton,npcm750-adc"; > + reg = <0xc000 0x8>; > + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clk NPCM7XX_CLK_ADC>; > + resets = <&rstc NPCM7XX_RESET_IPSRST1 NPCM7XX_RESET_ADC>; > + status = "disabled"; > + }; > + > + pwm_fan:pwm-fan-controller@103000 { Space after the : > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "nuvoton,npcm750-pwm-fan"; > + reg = <0x103000 0x2000>, <0x180000 0x8000>; > + reg-names = "pwm", "fan"; > + clocks = <&clk NPCM7XX_CLK_APB3>, > + <&clk NPCM7XX_CLK_APB4>; > + clock-names = "pwm","fan"; > + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pwm0_pins &pwm1_pins > + &pwm2_pins &pwm3_pins > + &pwm4_pins &pwm5_pins > + &pwm6_pins &pwm7_pins > + &fanin0_pins &fanin1_pins > + &fanin2_pins &fanin3_pins > + &fanin4_pins &fanin5_pins > + &fanin6_pins &fanin7_pins > + &fanin8_pins &fanin9_pins > + &fanin10_pins &fanin11_pins > + &fanin12_pins &fanin13_pins > + &fanin14_pins &fanin15_pins>; > + status = "disabled"; > + }; > + > + i2c0: i2c@80000 { > + reg = <0x80000 0x1000>; > + compatible = "nuvoton,npcm750-i2c"; > + #address-cells = <1>; > + #size-cells = <0>; > + clocks = <&clk NPCM7XX_CLK_APB2>; > + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&smb0_pins>; > + status = "disabled"; > + }; > + > + i2c1: i2c@81000 { > + reg = <0x81000 0x1000>; > + compatible = "nuvoton,npcm750-i2c"; > + #address-cells = <1>; > + #size-cells = <0>; > + clocks = <&clk NPCM7XX_CLK_APB2>; > + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&smb1_pins>; > + status = "disabled"; > + }; > + > + i2c2: i2c@82000 { > + reg = <0x82000 0x1000>; > + compatible = "nuvoton,npcm750-i2c"; > + #address-cells = <1>; > + #size-cells = <0>; > + clocks = <&clk NPCM7XX_CLK_APB2>; > + interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&smb2_pins>; > + status = "disabled"; > + }; > + > + i2c3: i2c@83000 { > + reg = <0x83000 0x1000>; > + compatible = "nuvoton,npcm750-i2c"; > + #address-cells = <1>; > + #size-cells = <0>; > + clocks = <&clk NPCM7XX_CLK_APB2>; > + interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&smb3_pins>; > + status = "disabled"; > + }; > + > + i2c4: i2c@84000 { > + reg = <0x84000 0x1000>; > + compatible = "nuvoton,npcm750-i2c"; > + #address-cells = <1>; > + #size-cells = <0>; > + clocks = <&clk NPCM7XX_CLK_APB2>; > + interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&smb4_pins>; > + status = "disabled"; > + }; > + > + i2c5: i2c@85000 { > + reg = <0x85000 0x1000>; > + compatible = "nuvoton,npcm750-i2c"; > + #address-cells = <1>; > + #size-cells = <0>; > + clocks = <&clk NPCM7XX_CLK_APB2>; > + interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&smb5_pins>; > + status = "disabled"; > + }; > + > + i2c6: i2c@86000 { > + reg = <0x86000 0x1000>; > + compatible = "nuvoton,npcm750-i2c"; > + #address-cells = <1>; > + #size-cells = <0>; > + clocks = <&clk NPCM7XX_CLK_APB2>; > + interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&smb6_pins>; > + status = "disabled"; > + }; > + > + i2c7: i2c@87000 { > + reg = <0x87000 0x1000>; > + compatible = "nuvoton,npcm750-i2c"; > + #address-cells = <1>; > + #size-cells = <0>; > + clocks = <&clk NPCM7XX_CLK_APB2>; > + interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&smb7_pins>; > + status = "disabled"; > + }; > + > + i2c8: i2c@88000 { > + reg = <0x88000 0x1000>; > + compatible = "nuvoton,npcm750-i2c"; > + #address-cells = <1>; > + #size-cells = <0>; > + clocks = <&clk NPCM7XX_CLK_APB2>; > + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&smb8_pins>; > + status = "disabled"; > + }; > + > + i2c9: i2c@89000 { > + reg = <0x89000 0x1000>; > + compatible = "nuvoton,npcm750-i2c"; > + #address-cells = <1>; > + #size-cells = <0>; > + clocks = <&clk NPCM7XX_CLK_APB2>; > + interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&smb9_pins>; > + status = "disabled"; > + }; > + > + i2c10: i2c@8a000 { > + reg = <0x8a000 0x1000>; > + compatible = "nuvoton,npcm750-i2c"; > + #address-cells = <1>; > + #size-cells = <0>; > + clocks = <&clk NPCM7XX_CLK_APB2>; > + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&smb10_pins>; > + status = "disabled"; > + }; > + > + i2c11: i2c@8b000 { > + reg = <0x8b000 0x1000>; > + compatible = "nuvoton,npcm750-i2c"; > + #address-cells = <1>; > + #size-cells = <0>; > + clocks = <&clk NPCM7XX_CLK_APB2>; > + interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&smb11_pins>; > + status = "disabled"; > + }; > + > + i2c12: i2c@8c000 { > + reg = <0x8c000 0x1000>; > + compatible = "nuvoton,npcm750-i2c"; > + #address-cells = <1>; > + #size-cells = <0>; > + clocks = <&clk NPCM7XX_CLK_APB2>; > + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&smb12_pins>; > + status = "disabled"; > + }; > + > + i2c13: i2c@8d000 { > + reg = <0x8d000 0x1000>; > + compatible = "nuvoton,npcm750-i2c"; > + #address-cells = <1>; > + #size-cells = <0>; > + clocks = <&clk NPCM7XX_CLK_APB2>; > + interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&smb13_pins>; > + status = "disabled"; > + }; > + > + i2c14: i2c@8e000 { > + reg = <0x8e000 0x1000>; > + compatible = "nuvoton,npcm750-i2c"; > + #address-cells = <1>; > + #size-cells = <0>; > + clocks = <&clk NPCM7XX_CLK_APB2>; > + interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&smb14_pins>; > + status = "disabled"; > + }; > + > + i2c15: i2c@8f000 { > + reg = <0x8f000 0x1000>; > + compatible = "nuvoton,npcm750-i2c"; > + #address-cells = <1>; > + #size-cells = <0>; > + clocks = <&clk NPCM7XX_CLK_APB2>; > + interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&smb15_pins>; > + status = "disabled"; > + }; > + }; > + }; > + > + pinctrl: pinctrl@f0800000 { > + #address-cells = <1>; > + #size-cells = <1>; > + compatible = "nuvoton,npcm750-pinctrl", "syscon", "simple-mfd"; > + ranges = <0 0xf0010000 0x8000>; > + status = "okay"; > + gpio0: gpio@f0010000 { > + gpio-controller; > + #gpio-cells = <2>; > + reg = <0x0 0x80>; > + interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>; > + gpio-ranges = <&pinctrl 0 0 32>; > + }; > + gpio1: gpio@f0011000 { > + gpio-controller; > + #gpio-cells = <2>; > + reg = <0x1000 0x80>; > + interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; > + gpio-ranges = <&pinctrl 0 32 32>; > + }; > + gpio2: gpio@f0012000 { > + gpio-controller; > + #gpio-cells = <2>; > + reg = <0x2000 0x80>; > + interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; > + gpio-ranges = <&pinctrl 0 64 32>; > + }; > + gpio3: gpio@f0013000 { > + gpio-controller; > + #gpio-cells = <2>; > + reg = <0x3000 0x80>; > + interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; > + gpio-ranges = <&pinctrl 0 96 32>; > + }; > + gpio4: gpio@f0014000 { > + gpio-controller; > + #gpio-cells = <2>; > + reg = <0x4000 0x80>; > + interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; > + gpio-ranges = <&pinctrl 0 128 32>; > + }; > + gpio5: gpio@f0015000 { > + gpio-controller; > + #gpio-cells = <2>; > + reg = <0x5000 0x80>; > + interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; > + gpio-ranges = <&pinctrl 0 160 32>; > + }; > + gpio6: gpio@f0016000 { > + gpio-controller; > + #gpio-cells = <2>; > + reg = <0x6000 0x80>; > + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>; > + gpio-ranges = <&pinctrl 0 192 32>; > + }; > + gpio7: gpio@f0017000 { > + gpio-controller; > + #gpio-cells = <2>; > + reg = <0x7000 0x80>; > + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; > + gpio-ranges = <&pinctrl 0 224 32>; > + }; > + > + iox1_pins: iox1-pins { > + groups = "iox1"; > + function = "iox1"; > + }; > + iox2_pins: iox2-pins { > + groups = "iox2"; > + function = "iox2"; > + }; > + smb1d_pins: smb1d-pins { > + groups = "smb1d"; > + function = "smb1d"; > + }; > + smb2d_pins: smb2d-pins { > + groups = "smb2d"; > + function = "smb2d"; > + }; > + lkgpo1_pins: lkgpo1-pins { > + groups = "lkgpo1"; > + function = "lkgpo1"; > + }; > + lkgpo2_pins: lkgpo2-pins { > + groups = "lkgpo2"; > + function = "lkgpo2"; > + }; > + ioxh_pins: ioxh-pins { > + groups = "ioxh"; > + function = "ioxh"; > + }; > + gspi_pins: gspi-pins { > + groups = "gspi"; > + function = "gspi"; > + }; > + smb5b_pins: smb5b-pins { > + groups = "smb5b"; > + function = "smb5b"; > + }; > + smb5c_pins: smb5c-pins { > + groups = "smb5c"; > + function = "smb5c"; > + }; > + lkgpo0_pins: lkgpo0-pins { > + groups = "lkgpo0"; > + function = "lkgpo0"; > + }; > + pspi2_pins: pspi2-pins { > + groups = "pspi2"; > + function = "pspi2"; > + }; > + smb4den_pins: smb4den-pins { > + groups = "smb4den"; > + function = "smb4den"; > + }; > + smb4b_pins: smb4b-pins { > + groups = "smb4b"; > + function = "smb4b"; > + }; > + smb4c_pins: smb4c-pins { > + groups = "smb4c"; > + function = "smb4c"; > + }; > + smb15_pins: smb15-pins { > + groups = "smb15"; > + function = "smb15"; > + }; > + smb4d_pins: smb4d-pins { > + groups = "smb4d"; > + function = "smb4d"; > + }; > + smb14_pins: smb14-pins { > + groups = "smb14"; > + function = "smb14"; > + }; > + smb5_pins: smb5-pins { > + groups = "smb5"; > + function = "smb5"; > + }; > + smb4_pins: smb4-pins { > + groups = "smb4"; > + function = "smb4"; > + }; > + smb3_pins: smb3-pins { > + groups = "smb3"; > + function = "smb3"; > + }; > + spi0cs1_pins: spi0cs1-pins { > + groups = "spi0cs1"; > + function = "spi0cs1"; > + }; > + spi0cs2_pins: spi0cs2-pins { > + groups = "spi0cs2"; > + function = "spi0cs2"; > + }; > + spi0cs3_pins: spi0cs3-pins { > + groups = "spi0cs3"; > + function = "spi0cs3"; > + }; > + smb3c_pins: smb3c-pins { > + groups = "smb3c"; > + function = "smb3c"; > + }; > + smb3b_pins: smb3b-pins { > + groups = "smb3b"; > + function = "smb3b"; > + }; > + bmcuart0a_pins: bmcuart0a-pins { > + groups = "bmcuart0a"; > + function = "bmcuart0a"; > + }; > + uart1_pins: uart1-pins { > + groups = "uart1"; > + function = "uart1"; > + }; > + jtag2_pins: jtag2-pins { > + groups = "jtag2"; > + function = "jtag2"; > + }; > + bmcuart1_pins: bmcuart1-pins { > + groups = "bmcuart1"; > + function = "bmcuart1"; > + }; > + uart2_pins: uart2-pins { > + groups = "uart2"; > + function = "uart2"; > + }; > + bmcuart0b_pins: bmcuart0b-pins { > + groups = "bmcuart0b"; > + function = "bmcuart0b"; > + }; > + r1err_pins: r1err-pins { > + groups = "r1err"; > + function = "r1err"; > + }; > + r1md_pins: r1md-pins { > + groups = "r1md"; > + function = "r1md"; > + }; > + smb3d_pins: smb3d-pins { > + groups = "smb3d"; > + function = "smb3d"; > + }; > + fanin0_pins: fanin0-pins { > + groups = "fanin0"; > + function = "fanin0"; > + }; > + fanin1_pins: fanin1-pins { > + groups = "fanin1"; > + function = "fanin1"; > + }; > + fanin2_pins: fanin2-pins { > + groups = "fanin2"; > + function = "fanin2"; > + }; > + fanin3_pins: fanin3-pins { > + groups = "fanin3"; > + function = "fanin3"; > + }; > + fanin4_pins: fanin4-pins { > + groups = "fanin4"; > + function = "fanin4"; > + }; > + fanin5_pins: fanin5-pins { > + groups = "fanin5"; > + function = "fanin5"; > + }; > + fanin6_pins: fanin6-pins { > + groups = "fanin6"; > + function = "fanin6"; > + }; > + fanin7_pins: fanin7-pins { > + groups = "fanin7"; > + function = "fanin7"; > + }; > + fanin8_pins: fanin8-pins { > + groups = "fanin8"; > + function = "fanin8"; > + }; > + fanin9_pins: fanin9-pins { > + groups = "fanin9"; > + function = "fanin9"; > + }; > + fanin10_pins: fanin10-pins { > + groups = "fanin10"; > + function = "fanin10"; > + }; > + fanin11_pins: fanin11-pins { > + groups = "fanin11"; > + function = "fanin11"; > + }; > + fanin12_pins: fanin12-pins { > + groups = "fanin12"; > + function = "fanin12"; > + }; > + fanin13_pins: fanin13-pins { > + groups = "fanin13"; > + function = "fanin13"; > + }; > + fanin14_pins: fanin14-pins { > + groups = "fanin14"; > + function = "fanin14"; > + }; > + fanin15_pins: fanin15-pins { > + groups = "fanin15"; > + function = "fanin15"; > + }; > + pwm0_pins: pwm0-pins { > + groups = "pwm0"; > + function = "pwm0"; > + }; > + pwm1_pins: pwm1-pins { > + groups = "pwm1"; > + function = "pwm1"; > + }; > + pwm2_pins: pwm2-pins { > + groups = "pwm2"; > + function = "pwm2"; > + }; > + pwm3_pins: pwm3-pins { > + groups = "pwm3"; > + function = "pwm3"; > + }; > + r2_pins: r2-pins { > + groups = "r2"; > + function = "r2"; > + }; > + r2err_pins: r2err-pins { > + groups = "r2err"; > + function = "r2err"; > + }; > + r2md_pins: r2md-pins { > + groups = "r2md"; > + function = "r2md"; > + }; > + ga20kbc_pins: ga20kbc-pins { > + groups = "ga20kbc"; > + function = "ga20kbc"; > + }; > + smb5d_pins: smb5d-pins { > + groups = "smb5d"; > + function = "smb5d"; > + }; > + lpc_pins: lpc-pins { > + groups = "lpc"; > + function = "lpc"; > + }; > + espi_pins: espi-pins { > + groups = "espi"; > + function = "espi"; > + }; > + rg1_pins: rg1-pins { > + groups = "rg1"; > + function = "rg1"; > + }; > + rg1mdio_pins: rg1mdio-pins { > + groups = "rg1mdio"; > + function = "rg1mdio"; > + }; > + rg2_pins: rg2-pins { > + groups = "rg2"; > + function = "rg2"; > + }; > + ddr_pins: ddr-pins { > + groups = "ddr"; > + function = "ddr"; > + }; > + smb0_pins: smb0-pins { > + groups = "smb0"; > + function = "smb0"; > + }; > + smb1_pins: smb1-pins { > + groups = "smb1"; > + function = "smb1"; > + }; > + smb2_pins: smb2-pins { > + groups = "smb2"; > + function = "smb2"; > + }; > + smb2c_pins: smb2c-pins { > + groups = "smb2c"; > + function = "smb2c"; > + }; > + smb2b_pins: smb2b-pins { > + groups = "smb2b"; > + function = "smb2b"; > + }; > + smb1c_pins: smb1c-pins { > + groups = "smb1c"; > + function = "smb1c"; > + }; > + smb1b_pins: smb1b-pins { > + groups = "smb1b"; > + function = "smb1b"; > + }; > + smb8_pins: smb8-pins { > + groups = "smb8"; > + function = "smb8"; > + }; > + smb9_pins: smb9-pins { > + groups = "smb9"; > + function = "smb9"; > + }; > + smb10_pins: smb10-pins { > + groups = "smb10"; > + function = "smb10"; > + }; > + smb11_pins: smb11-pins { > + groups = "smb11"; > + function = "smb11"; > + }; > + sd1_pins: sd1-pins { > + groups = "sd1"; > + function = "sd1"; > + }; > + sd1pwr_pins: sd1pwr-pins { > + groups = "sd1pwr"; > + function = "sd1pwr"; > + }; > + pwm4_pins: pwm4-pins { > + groups = "pwm4"; > + function = "pwm4"; > + }; > + pwm5_pins: pwm5-pins { > + groups = "pwm5"; > + function = "pwm5"; > + }; > + pwm6_pins: pwm6-pins { > + groups = "pwm6"; > + function = "pwm6"; > + }; > + pwm7_pins: pwm7-pins { > + groups = "pwm7"; > + function = "pwm7"; > + }; > + mmc8_pins: mmc8-pins { > + groups = "mmc8"; > + function = "mmc8"; > + }; > + mmc_pins: mmc-pins { > + groups = "mmc"; > + function = "mmc"; > + }; > + mmcwp_pins: mmcwp-pins { > + groups = "mmcwp"; > + function = "mmcwp"; > + }; > + mmccd_pins: mmccd-pins { > + groups = "mmccd"; > + function = "mmccd"; > + }; > + mmcrst_pins: mmcrst-pins { > + groups = "mmcrst"; > + function = "mmcrst"; > + }; > + clkout_pins: clkout-pins { > + groups = "clkout"; > + function = "clkout"; > + }; > + serirq_pins: serirq-pins { > + groups = "serirq"; > + function = "serirq"; > + }; > + lpcclk_pins: lpcclk-pins { > + groups = "lpcclk"; > + function = "lpcclk"; > + }; > + scipme_pins: scipme-pins { > + groups = "scipme"; > + function = "scipme"; > + }; > + sci_pins: sci-pins { > + groups = "sci"; > + function = "sci"; > + }; > + smb6_pins: smb6-pins { > + groups = "smb6"; > + function = "smb6"; > + }; > + smb7_pins: smb7-pins { > + groups = "smb7"; > + function = "smb7"; > + }; > + pspi1_pins: pspi1-pins { > + groups = "pspi1"; > + function = "pspi1"; > + }; > + faninx_pins: faninx-pins { > + groups = "faninx"; > + function = "faninx"; > + }; > + r1_pins: r1-pins { > + groups = "r1"; > + function = "r1"; > + }; > + spi3_pins: spi3-pins { > + groups = "spi3"; > + function = "spi3"; > + }; > + spi3cs1_pins: spi3cs1-pins { > + groups = "spi3cs1"; > + function = "spi3cs1"; > + }; > + spi3quad_pins: spi3quad-pins { > + groups = "spi3quad"; > + function = "spi3quad"; > + }; > + spi3cs2_pins: spi3cs2-pins { > + groups = "spi3cs2"; > + function = "spi3cs2"; > + }; > + spi3cs3_pins: spi3cs3-pins { > + groups = "spi3cs3"; > + function = "spi3cs3"; > + }; > + nprd_smi_pins: nprd-smi-pins { > + groups = "nprd_smi"; > + function = "nprd_smi"; > + }; > + smb0b_pins: smb0b-pins { > + groups = "smb0b"; > + function = "smb0b"; > + }; > + smb0c_pins: smb0c-pins { > + groups = "smb0c"; > + function = "smb0c"; > + }; > + smb0den_pins: smb0den-pins { > + groups = "smb0den"; > + function = "smb0den"; > + }; > + smb0d_pins: smb0d-pins { > + groups = "smb0d"; > + function = "smb0d"; > + }; > + ddc_pins: ddc-pins { > + groups = "ddc"; > + function = "ddc"; > + }; > + rg2mdio_pins: rg2mdio-pins { > + groups = "rg2mdio"; > + function = "rg2mdio"; > + }; > + wdog1_pins: wdog1-pins { > + groups = "wdog1"; > + function = "wdog1"; > + }; > + wdog2_pins: wdog2-pins { > + groups = "wdog2"; > + function = "wdog2"; > + }; > + smb12_pins: smb12-pins { > + groups = "smb12"; > + function = "smb12"; > + }; > + smb13_pins: smb13-pins { > + groups = "smb13"; > + function = "smb13"; > + }; > + spix_pins: spix-pins { > + groups = "spix"; > + function = "spix"; > + }; > + spixcs1_pins: spixcs1-pins { > + groups = "spixcs1"; > + function = "spixcs1"; > + }; > + clkreq_pins: clkreq-pins { > + groups = "clkreq"; > + function = "clkreq"; > + }; > + hgpio0_pins: hgpio0-pins { > + groups = "hgpio0"; > + function = "hgpio0"; > + }; > + hgpio1_pins: hgpio1-pins { > + groups = "hgpio1"; > + function = "hgpio1"; > + }; > + hgpio2_pins: hgpio2-pins { > + groups = "hgpio2"; > + function = "hgpio2"; > + }; > + hgpio3_pins: hgpio3-pins { > + groups = "hgpio3"; > + function = "hgpio3"; > + }; > + hgpio4_pins: hgpio4-pins { > + groups = "hgpio4"; > + function = "hgpio4"; > + }; > + hgpio5_pins: hgpio5-pins { > + groups = "hgpio5"; > + function = "hgpio5"; > + }; > + hgpio6_pins: hgpio6-pins { > + groups = "hgpio6"; > + function = "hgpio6"; > + }; > + hgpio7_pins: hgpio7-pins { > + groups = "hgpio7"; > + function = "hgpio7"; > }; > }; > }; > diff --git a/arch/arm/boot/dts/nuvoton-npcm750-evb.dts b/arch/arm/boot/dts/nuvoton-npcm750-evb.dts > index 15f744f1beea..0af79573ab28 100644 > --- a/arch/arm/boot/dts/nuvoton-npcm750-evb.dts > +++ b/arch/arm/boot/dts/nuvoton-npcm750-evb.dts Put this in a speparate patch. > @@ -4,36 +4,404 @@ > > /dts-v1/; > #include "nuvoton-npcm750.dtsi" > +#include "dt-bindings/gpio/gpio.h" > +#include "nuvoton-npcm750-pincfg-evb.dtsi" > > / { > model = "Nuvoton npcm750 Development Board (Device Tree)"; > compatible = "nuvoton,npcm750"; > > + aliases { > + ethernet2 = &gmac0; > + ethernet3 = &gmac1; > + serial0 = &serial0; > + serial1 = &serial1; > + serial2 = &serial2; > + serial3 = &serial3; > + i2c0 = &i2c0; > + i2c1 = &i2c1; > + i2c2 = &i2c2; > + i2c3 = &i2c3; > + i2c4 = &i2c4; > + i2c5 = &i2c5; > + i2c6 = &i2c6; > + i2c7 = &i2c7; > + i2c8 = &i2c8; > + i2c9 = &i2c9; > + i2c10 = &i2c10; > + i2c11 = &i2c11; > + i2c12 = &i2c12; > + i2c13 = &i2c13; > + i2c14 = &i2c14; > + i2c15 = &i2c15; > + spi0 = &spi0; > + spi1 = &spi1; > + fiu0 = &fiu0; > + fiu1 = &fiu3; > + fiu2 = &fiux; > + }; > + > chosen { > stdout-path = &serial3; > }; > > - memory { > - reg = <0 0x40000000>; > - }; > -}; > + ahb { > + gmac0: eth@f0802000 { > + phy-mode = "rgmii-id"; > + status = "okay"; > + }; > > -&watchdog1 { > - status = "okay"; > -}; > + gmac1: eth@f0804000 { > + phy-mode = "rgmii-id"; > + status = "okay"; > + }; > > -&serial0 { > - status = "okay"; > -}; > + ehci1: usb@f0806000 { > + status = "okay"; > + }; > > -&serial1 { > - status = "okay"; > -}; > + fiu0: spi@fb000000 { > + status = "okay"; > + spi-nor@0 { > + compatible = "jedec,spi-nor"; > + #address-cells = <1>; > + #size-cells = <1>; > + spi-rx-bus-width = <2>; > + reg = <0>; > + spi-max-frequency = <5000000>; > + partitions@80000000 { > + compatible = "fixed-partitions"; > + #address-cells = <1>; > + #size-cells = <1>; > + bbuboot1@0 { > + label = "bb-uboot-1"; > + reg = <0x0000000 0x80000>; > + read-only; > + }; > + bbuboot2@80000 { > + label = "bb-uboot-2"; > + reg = <0x0080000 0x80000>; > + read-only; > + }; > + envparam@100000 { > + label = "env-param"; > + reg = <0x0100000 0x40000>; > + read-only; > + }; > + spare@140000 { > + label = "spare"; > + reg = <0x0140000 0xC0000>; > + }; > + kernel@200000 { > + label = "kernel"; > + reg = <0x0200000 0x400000>; > + }; > + rootfs@600000 { > + label = "rootfs"; > + reg = <0x0600000 0x700000>; > + }; > + spare1@D00000 { > + label = "spare1"; > + reg = <0x0D00000 0x200000>; > + }; > + spare2@0F00000 { > + label = "spare2"; > + reg = <0x0F00000 0x200000>; > + }; > + spare3@1100000 { > + label = "spare3"; > + reg = <0x1100000 0x200000>; > + }; > + spare4@1300000 { > + label = "spare4"; > + reg = <0x1300000 0x0>; > + }; > + }; > + }; > + }; > > -&serial2 { > - status = "okay"; > -}; > + fiu3: spi@c0000000 { > + pinctrl-0 = <&spi3_pins>, <&spi3quad_pins>; > + status = "okay"; > + spi-nor@0 { > + compatible = "jedec,spi-nor"; > + #address-cells = <1>; > + #size-cells = <1>; > + spi-rx-bus-width = <2>; > + reg = <0>; > + spi-max-frequency = <5000000>; > + partitions@A0000000 { > + compatible = "fixed-partitions"; > + #address-cells = <1>; > + #size-cells = <1>; > + system1@0 { > + label = "spi3-system1"; > + reg = <0x0 0x0>; > + }; > + }; > + }; > + }; > + > + fiux: spi@fb001000 { > + spix-mode; > + }; > + > + apb { > + > + watchdog1: watchdog@901C { > + status = "okay"; > + }; > + > + rng: rng@b000 { > + status = "okay"; > + }; > + > + serial0: serial@1000 { > + status = "okay"; > + }; > + > + serial1: serial@2000 { > + status = "okay"; > + }; > + > + serial2: serial@3000 { > + status = "okay"; > + }; > + > + serial3: serial@4000 { > + status = "okay"; > + }; > + > + adc: adc@c000 { > + status = "okay"; > + }; > + > + otp:otp@189000 { > + status = "okay"; > + }; > + > + lpc_kcs: lpc_kcs@7000 { > + kcs1: kcs1@0 { > + status = "okay"; > + }; > > -&serial3 { > - status = "okay"; > + kcs2: kcs2@0 { > + status = "okay"; > + }; > + > + kcs3: kcs3@0 { > + status = "okay"; > + }; > + }; > + > + /* lm75 on SVB */ > + i2c0: i2c@80000 { > + clock-frequency = <100000>; > + status = "okay"; > + lm75@48 { > + compatible = "lm75"; > + reg = <0x48>; > + status = "okay"; > + }; > + }; > + > + /* lm75 on EB */ > + i2c1: i2c@81000 { > + clock-frequency = <100000>; > + status = "okay"; > + lm75@48 { > + compatible = "lm75"; > + reg = <0x48>; > + status = "okay"; > + }; > + }; > + > + /* tmp100 on EB */ > + i2c2: i2c@82000 { > + clock-frequency = <100000>; > + status = "okay"; > + tmp100@48 { > + compatible = "tmp100"; > + reg = <0x48>; > + status = "okay"; > + }; > + }; > + > + i2c3: i2c@83000 { > + clock-frequency = <100000>; > + status = "okay"; > + }; > + > + i2c5: i2c@85000 { > + clock-frequency = <100000>; > + status = "okay"; > + }; > + > + /* tmp100 on SVB */ > + i2c6: i2c@86000 { > + clock-frequency = <100000>; > + status = "okay"; > + tmp100@48 { > + compatible = "tmp100"; > + reg = <0x48>; > + status = "okay"; > + }; > + }; > + > + i2c7: i2c@87000 { > + clock-frequency = <100000>; > + status = "okay"; > + }; > + > + i2c8: i2c@88000 { > + clock-frequency = <100000>; > + status = "okay"; > + }; > + > + i2c9: i2c@89000 { > + clock-frequency = <100000>; > + status = "okay"; > + }; > + > + i2c10: i2c@8a000 { > + clock-frequency = <100000>; > + status = "okay"; > + }; > + > + i2c11: i2c@8b000 { > + clock-frequency = <100000>; > + status = "okay"; > + }; > + > + i2c14: i2c@8e000 { > + clock-frequency = <100000>; > + status = "okay"; > + }; > + > + pwm_fan:pwm-fan-controller@103000 { > + status = "okay"; > + fan@0 { > + reg = <0x00>; > + fan-tach-ch = /bits/ 8 <0x00 0x01>; > + cooling-levels = <127 255>; > + }; > + fan@1 { > + reg = <0x01>; > + fan-tach-ch = /bits/ 8 <0x02 0x03>; > + cooling-levels = /bits/ 8 <127 255>; > + }; > + fan@2 { > + reg = <0x02>; > + fan-tach-ch = /bits/ 8 <0x04 0x05>; > + cooling-levels = /bits/ 8 <127 255>; > + }; > + fan@3 { > + reg = <0x03>; > + fan-tach-ch = /bits/ 8 <0x06 0x07>; > + cooling-levels = /bits/ 8 <127 255>; > + }; > + fan@4 { > + reg = <0x04>; > + fan-tach-ch = /bits/ 8 <0x08 0x09>; > + cooling-levels = /bits/ 8 <127 255>; > + }; > + fan@5 { > + reg = <0x05>; > + fan-tach-ch = /bits/ 8 <0x0A 0x0B>; > + cooling-levels = /bits/ 8 <127 255>; > + }; > + fan@6 { > + reg = <0x06>; > + fan-tach-ch = /bits/ 8 <0x0C 0x0D>; > + cooling-levels = /bits/ 8 <127 255>; > + }; > + fan@7 { > + reg = <0x07>; > + fan-tach-ch = /bits/ 8 <0x0E 0x0F>; > + cooling-levels = /bits/ 8 <127 255>; > + }; > + }; > + > + spi0: spi@200000 { > + cs-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>; > + status = "okay"; > + Flash@0 { > + compatible = "winbond,w25q128", > + "jedec,spi-nor"; > + reg = <0x0>; > + #address-cells = <1>; > + #size-cells = <1>; > + spi-max-frequency = <5000000>; > + partition@0 { > + label = "spi0_spare1"; > + reg = <0x0000000 0x800000>; > + }; > + partition@1 { > + label = "spi0_spare2"; > + reg = <0x800000 0x0>; > + }; > + }; > + }; > + > + spi1: spi@201000 { > + cs-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; > + status = "okay"; > + Flash@0 { > + compatible = "winbond,w25q128fw", > + "jedec,spi-nor"; > + reg = <0x0>; > + #address-cells = <1>; > + #size-cells = <1>; > + spi-max-frequency = <5000000>; > + partition@0 { > + label = "spi1_spare1"; > + reg = <0x0000000 0x800000>; > + }; > + partition@1 { > + label = "spi1_spare2"; > + reg = <0x800000 0x0>; > + }; > + }; > + }; > + }; > + }; > + > + pinctrl: pinctrl@f0800000 { > + pinctrl-names = "default"; > + pinctrl-0 = < &iox1_pins > + &pin8_input > + &pin9_output_high > + &pin10_input > + &pin11_output_high > + &pin16_input > + &pin24_output_high > + &pin25_output_low > + &pin32_output_high > + &jtag2_pins > + &pin61_output_high > + &pin62_output_high > + &pin63_output_high > + &lpc_pins > + &pin160_input > + &pin162_input > + &pin168_input > + &pin169_input > + &pin170_input > + &pin187_output_high > + &pin190_input > + &pin191_output_high > + &pin192_output_high > + &pin197_output_low > + &ddc_pins > + &pin218_input > + &pin219_output_low > + &pin220_output_low > + &pin221_output_high > + &pin222_input > + &pin223_output_low > + &spix_pins > + &pin228_output_low > + &pin231_output_high > + &pin255_input>; > + }; > }; > diff --git a/arch/arm/boot/dts/nuvoton-npcm750-pincfg-evb.dtsi b/arch/arm/boot/dts/nuvoton-npcm750-pincfg-evb.dtsi > new file mode 100644 > index 000000000000..edb4190826e6 > --- /dev/null > +++ b/arch/arm/boot/dts/nuvoton-npcm750-pincfg-evb.dtsi > @@ -0,0 +1,157 @@ > +// SPDX-License-Identifier: GPL-2.0 > +// Copyright (c) 2018 Nuvoton Technology tomer.maimon@nuvoton.com > + > +/ { > + pinctrl: pinctrl@f0800000 { > + pin8_input: pin8-input { > + pins = "GPIO8/LKGPO1"; > + bias-disable; > + input-enable; > + }; > + pin9_output_high: pin9-output-high { > + pins = "GPIO9/LKGPO2"; > + bias-disable; > + output-high; > + }; > + pin10_input: pin10-input { > + pins = "GPIO10/IOXHLD"; > + bias-disable; > + input-enable; > + }; > + pin11_output_high: pin11-output-high { > + pins = "GPIO11/IOXHCK"; > + bias-disable; > + output-high; > + }; > + pin16_input: pin16-input { > + pins = "GPIO16/LKGPO0"; > + bias-disable; > + input-enable; > + }; > + pin24_output_high: pin24-output-high { > + pins = "GPIO24/IOXHDO"; > + bias-disable; > + output-high; > + }; > + pin25_output_low: pin25-output-low { > + pins = "GPIO25/IOXHDI"; > + bias-disable; > + output-low; > + }; > + pin32_output_high: pin32-output-high { > + pins = "GPIO32/nSPI0CS1"; > + bias-disable; > + output-high; > + }; > + pin61_output_high: pin61-output-high { > + pins = "GPO61/nDTR1_BOUT1/STRAP6"; > + bias-disable; > + output-high; > + }; > + pin62_output_high: pin62-output-high { > + pins = "GPO62/nRTST1/STRAP5"; > + bias-disable; > + output-high; > + }; > + pin63_output_high: pin63-output-high { > + pins = "GPO63/TXD1/STRAP4"; > + bias-disable; > + output-high; > + }; > + pin160_input: pin160-input { > + pins = "GPIO160/CLKOUT/RNGOSCOUT"; > + bias-disable; > + input-enable; > + }; > + pin162_input: pin162-input { > + pins = "GPIO162/SERIRQ"; > + bias-disable; > + input-enable; > + }; > + pin168_input: pin168-input { > + pins = "GPIO168/nCLKRUN/nESPIALERT"; > + bias-disable; > + input-enable; > + }; > + pin169_input: pin169-input { > + pins = "GPIO169/nSCIPME"; > + bias-disable; > + input-enable; > + }; > + pin170_input: pin170-input { > + pins = "GPIO170/nSMI"; > + bias-disable; > + input-enable; > + }; > + pin187_output_high: pin187-output-high { > + pins = "GPIO187/nSPI3CS1"; > + bias-disable; > + output-high; > + }; > + pin190_input: pin190-input { > + pins = "GPIO190/nPRD_SMI"; > + bias-disable; > + input-enable; > + }; > + pin191_output_high: pin191-output-high { > + pins = "GPIO191"; > + bias-disable; > + output-high; > + }; > + pin192_output_high: pin192-output-high { > + pins = "GPIO192"; > + bias-disable; > + output-high; > + }; > + pin197_output_low: pin197-output-low { > + pins = "GPIO197/SMB0DEN"; > + bias-disable; > + output-low; > + }; > + pin218_input: pin218-input { > + pins = "GPIO218/nWDO1"; > + bias-disable; > + input-enable; > + }; > + pin219_output_low: pin219-output-low { > + pins = "GPIO219/nWDO2"; > + bias-disable; > + output-low; > + }; > + pin220_output_low: pin220-output-low { > + pins = "GPIO220/SMB12SCL"; > + bias-disable; > + output-low; > + }; > + pin221_output_high: pin221-output-high { > + pins = "GPIO221/SMB12SDA"; > + bias-disable; > + output-high; > + }; > + pin222_input: pin222-input { > + pins = "GPIO222/SMB13SCL"; > + bias-disable; > + input-enable; > + }; > + pin223_output_low: pin223-output-low { > + pins = "GPIO223/SMB13SDA"; > + bias-disable; > + output-low; > + }; > + pin228_output_low: pin228-output-low { > + pins = "GPIO228/nSPIXCS1"; > + bias-disable; > + output-low; > + }; > + pin231_output_high: pin231-output-high { > + pins = "GPIO230/SPIXD3"; > + bias-disable; > + output-high; > + }; > + pin255_input: pin255-input { > + pins = "GPI255/DACOSEL"; > + bias-disable; > + input-enable; > + }; > + }; > +}; > diff --git a/arch/arm/boot/dts/nuvoton-npcm750.dtsi b/arch/arm/boot/dts/nuvoton-npcm750.dtsi > index a37bb2294b8f..13eee0fe5642 100644 > --- a/arch/arm/boot/dts/nuvoton-npcm750.dtsi > +++ b/arch/arm/boot/dts/nuvoton-npcm750.dtsi Put this in a separate patch too. > @@ -32,6 +32,7 @@ > next-level-cache = <&l2>; > }; > }; > + > soc { > timer@3fe600 { > compatible = "arm,cortex-a9-twd-timer"; > @@ -41,4 +42,21 @@ > clocks = <&clk NPCM7XX_CLK_AHB>; > }; > }; > + > + ahb { > + gmac1: eth@f0804000 { > + device_type = "network"; > + compatible = "snps,dwmac"; > + reg = <0xf0804000 0x2000>; > + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "macirq"; > + ethernet = <1>; > + clocks = <&clk_rg2refck>, <&clk NPCM7XX_CLK_AHB>; > + clock-names = "stmmaceth", "clk_gmac"; > + pinctrl-names = "default"; > + pinctrl-0 = <&rg2_pins > + &rg2mdio_pins>; > + status = "disabled"; > + }; > + }; > }; > -- > 2.22.0 > ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v5 0/3] arm: dts: add and modify device node in NPCM7xx device tree 2020-09-16 12:55 [PATCH v5 0/3] arm: dts: add and modify device node in NPCM7xx device tree Tomer Maimon ` (2 preceding siblings ...) 2020-09-16 12:55 ` [PATCH v5 3/3] arm: dts: add new device nodes to NPCM750 device tree Tomer Maimon @ 2020-09-16 13:14 ` Joel Stanley 3 siblings, 0 replies; 8+ messages in thread From: Joel Stanley @ 2020-09-16 13:14 UTC (permalink / raw) To: Tomer Maimon Cc: Rob Herring, Mark Rutland, Avi Fishman, Tali Perry, Patrick Venture, Nancy Yuen, Benjamin Fair, devicetree, Linux Kernel Mailing List, OpenBMC Maillist Hi Tomer, On Wed, 16 Sep 2020 at 12:56, Tomer Maimon <tmaimon77@gmail.com> wrote: > > This patch set adds and modify device tree nodes in the NPCM7xx > Baseboard Management Controller (BMC) device tree. Thanks Tomer. I smoke tested these by booting on the npcm730 qemu machine. Are you able to submit the gsj device tree (or get someone who has worked on that to do so?) for inclusion too? Similarly for the runbmc device tree. We also lack a nuvoton configuration. We can submit one, or rely on the multi_v7 for upstream testing. What would you prefer? > The following device node add: > - NPCM7xx Pin controller and GPIO > - NPCM7xx PWM and FAN. > - NPCM7xx EHCI USB. > - NPCM7xx KCS. > - NPCM Reset. > - NPCM Peripheral SPI. > - NPCM FIU SPI. > - NPCM HWRNG. > - NPCM I2C. > - STMicro STMMAC. Does the STMMAC only appear in the 750 (and not the 730)? I was wondering why it appeared in the 750 dtsi and not the common dtsi. Cheers, Joel > > The following device node modified: > - NPCM7xx timer. > - NPCM7xx clock constants parameters. > > NPCM7xx device tree tested on NPCM750 evaluation board. > > Changes since version 4: > - Tested patches in Linux kernel 5.9. > > Changes since version 3: > - Tested patches in Linux kernel 5.6. > > Changes since version 2: > - Remove unnecessary output-enable flags. > > Changes since version 1: > - Add NPCM reset device node. > - Add reset parameters to NPCM driver device nodes. > > Tomer Maimon (3): > arm: dts: modify NPCM7xx device tree clock parameter > arm: dts: modify NPCM7xx device tree timer register size > arm: dts: add new device nodes to NPCM750 device tree > > arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi | 974 +++++++++++++++++- > arch/arm/boot/dts/nuvoton-npcm750-evb.dts | 404 +++++++- > .../boot/dts/nuvoton-npcm750-pincfg-evb.dtsi | 157 +++ > arch/arm/boot/dts/nuvoton-npcm750.dtsi | 24 +- > 4 files changed, 1522 insertions(+), 37 deletions(-) > create mode 100644 arch/arm/boot/dts/nuvoton-npcm750-pincfg-evb.dtsi > > -- > 2.22.0 > ^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2020-09-16 21:02 UTC | newest] Thread overview: 8+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2020-09-16 12:55 [PATCH v5 0/3] arm: dts: add and modify device node in NPCM7xx device tree Tomer Maimon 2020-09-16 12:55 ` [PATCH v5 1/3] arm: dts: modify NPCM7xx device tree clock parameter Tomer Maimon 2020-09-16 13:15 ` Joel Stanley 2020-09-16 12:55 ` [PATCH v5 2/3] arm: dts: modify NPCM7xx device tree timer register size Tomer Maimon 2020-09-16 13:21 ` Joel Stanley 2020-09-16 12:55 ` [PATCH v5 3/3] arm: dts: add new device nodes to NPCM750 device tree Tomer Maimon 2020-09-16 13:27 ` Joel Stanley 2020-09-16 13:14 ` [PATCH v5 0/3] arm: dts: add and modify device node in NPCM7xx " Joel Stanley
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).