From: Marco Felsch <m.felsch@pengutronix.de>
To: robh+dt@kernel.org, shawnguo@kernel.org, festevam@gmail.com,
linux-imx@nxp.com, m.podolszki@phytec.de
Cc: devicetree@vger.kernel.org, kernel@pengutronix.de
Subject: [PATCH 2/2] ARM: dts: imx6: Add support for phyBOARD-Nunki
Date: Wed, 7 Oct 2020 15:30:37 +0200 [thread overview]
Message-ID: <20201007133037.25315-2-m.felsch@pengutronix.de> (raw)
In-Reply-To: <20201007133037.25315-1-m.felsch@pengutronix.de>
From: Stefan Riedmueller <s.riedmueller@phytec.de>
This patch adds support for the PHYTEC phyBOARD-Nunki which is a
baseboard for the phyCORE-i.MX 6 especially designed for image
processing purposes. At this point it only supports the phyCORE-i.MX
6Quad and 6QuadPlus.
Features are:
- phyCORE-i.MX 6Quad/QuadPlus
- LVDS display
- HDMI
- GBit Ethernet
- USB Host
- USB OTG
- SATA
- PCIe
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Jan Remmet <j.remmet@phytec.de>
[m.felsch@pengutronix.de: squashed downstream commits:
ARM: dts: imx6: nunki: Add support for phytec cameras
ARM: dts: imx6qdl: nunki: Fix wrong pin settings
ARM: dts: imx6qdl: nunki: Enable pcie regulator active low
ARM: dts: imx6qdl: nunki: Remove enable-active-low property
ARM: dts: imx6qdl: nunki: Add muxing for camera strobe and trigger
ARM: dts: imx6qdl: nunki: fix rtc compatible
ARM: dts: imx6: nunki: Move optional camera bindings to separate dtsi]
[m.felsch@pengutronix.de:
- remove downstream camera and display .dtsi files
- reorder phandles
- adapt commit message to reflect new state
- move stdout-path to nunki.dtsi since it is the only possible debug
uart
- fix pwm-cells for backlight (new default is 3)
- remove not upstream available ti,scan921226h deserializers
- fix a few style issues (compatible first and so on)
- drop unecessary status lines
- keep ldb disabled
- move iomux node to the end]
[m.felsch@pengutronix.de:
- add support for phyCORE-i.MX 6QuadPlus]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
---
arch/arm/boot/dts/Makefile | 2 +
.../boot/dts/imx6q-phytec-nunki-rdk-nand.dts | 72 ++++
arch/arm/boot/dts/imx6qdl-phytec-nunki.dtsi | 361 ++++++++++++++++++
.../boot/dts/imx6qp-phytec-nunki-rdk-nand.dts | 71 ++++
4 files changed, 506 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-phytec-nunki-rdk-nand.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-nunki.dtsi
create mode 100644 arch/arm/boot/dts/imx6qp-phytec-nunki-rdk-nand.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 4572db3fa5ae..f55a043c0063 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -539,6 +539,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-novena.dtb \
imx6q-phytec-mira-rdk-emmc.dtb \
imx6q-phytec-mira-rdk-nand.dtb \
+ imx6q-phytec-nunki-rdk-nand.dtb \
imx6q-phytec-pbab01.dtb \
imx6q-pico-dwarf.dtb \
imx6q-pico-hobbit.dtb \
@@ -575,6 +576,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6qp-nitrogen6_max.dtb \
imx6qp-nitrogen6_som2.dtb \
imx6qp-phytec-mira-rdk-nand.dtb \
+ imx6qp-phytec-nunki-rdk-nand.dtb \
imx6qp-sabreauto.dtb \
imx6qp-sabresd.dtb \
imx6qp-tx6qp-8037.dtb \
diff --git a/arch/arm/boot/dts/imx6q-phytec-nunki-rdk-nand.dts b/arch/arm/boot/dts/imx6q-phytec-nunki-rdk-nand.dts
new file mode 100644
index 000000000000..3072f8e40a9e
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-phytec-nunki-rdk-nand.dts
@@ -0,0 +1,72 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright (C) 2018 PHYTEC Messtechnik GmbH
+ * Author: Martin Podolszki <m.podolszki@phytec.de>
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-phytec-phycore-som.dtsi"
+#include "imx6qdl-phytec-nunki.dtsi"
+
+/ {
+ model = "PHYTEC phyBOARD-Nunki Quad Carrier-Board with NAND";
+ compatible = "phytec,imx6q-pbac11-nand", "phytec,imx6q-pbac11",
+ "phytec,imx6qdl-pcm058", "fsl,imx6q";
+};
+
+&can1 {
+ status = "okay";
+};
+
+&fec {
+ status = "okay";
+};
+
+&gpmi {
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+};
+
+&i2c2 {
+ status = "okay";
+};
+
+&m25p80 {
+ status = "okay";
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&usbh1 {
+ status = "okay";
+};
+
+&usbotg {
+ status = "okay";
+};
+
+&usdhc1 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-phytec-nunki.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-nunki.dtsi
new file mode 100644
index 000000000000..1e2d00c281f7
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-phytec-nunki.dtsi
@@ -0,0 +1,361 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2018 PHYTEC Messtechnik GmbH
+ * Author: Martin Podolszki <m.podolszki@phytec.de>
+ */
+
+#include <dt-bindings/leds/leds-pca9532.h>
+
+/ {
+ aliases {
+ rtc0 = &i2c_rtc;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <7>;
+ power-supply = <®_lcd_3v3>;
+ pwms = <&pwm1 0 5000000 0>;
+ };
+
+ chosen {
+ stdout-path = &uart2;
+ };
+
+ panel {
+ compatible = "auo,g104sn02";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_panel_en>;
+ power-supply = <®_panel>;
+ enable-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
+ backlight = <&backlight>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+
+ reg_flexcan1: regulator-flexcan1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1_en>;
+ compatible = "regulator-fixed";
+ regulator-name = "flexcan1";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ gpio = <&gpio1 27 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_lcd_3v3: regulator-lcd-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ };
+
+ reg_en_switch: regulator-en-switch {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_en_switch>;
+ compatible = "regulator-fixed";
+ regulator-name = "Enable Switch";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 4 GPIO_ACTIVE_HIGH>;
+ regulator-always-on;
+ enable-active-high;
+ };
+
+ reg_panel: regulator-panel {
+ compatible = "regulator-fixed";
+ regulator-name = "panel-power-supply";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ };
+
+ reg_pcie: regulator-pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie_reg>;
+ compatible = "regulator-fixed";
+ regulator-name = "mPCIe_1V5";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_usbotg_vbus: regulator-usbotg-vbus {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg_vbus>;
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ xceiver-supply = <®_flexcan1>;
+};
+
+&hdmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hdmicec>;
+ ddc-i2c-bus = <&i2c2>;
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ clock-frequency = <100000>;
+
+ stmpe: touchctrl@44 {
+ compatible = "st,stmpe811";
+ reg = <0x44>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_stmpe>;
+ interrupts = <12 IRQ_TYPE_NONE>;
+ interrupt-parent = <&gpio7>;
+
+ stmpe_touchscreen {
+ compatible = "st,stmpe-ts";
+ st,sample-time = <4>;
+ st,mod-12b = <1>;
+ st,ref-sel = <0>;
+ st,adc-freq = <1>;
+ st,ave-ctrl = <1>;
+ st,touch-det-delay = <2>;
+ st,settling = <2>;
+ st,fraction-z = <7>;
+ st,i-drive = <1>;
+ };
+ };
+
+ pca9533: leddimmer@62 {
+ compatible = "nxp,pca9533";
+ reg = <0x62>;
+
+ led-red {
+ label = "red:user1";
+ type = <PCA9532_TYPE_LED>;
+ linux,default-trigger = "none";
+ };
+
+ led-green {
+ label = "green:user2";
+ type = <PCA9532_TYPE_LED>;
+ linux,default-trigger = "none";
+ };
+
+ led-blue {
+ label = "blue:user3";
+ type = <PCA9532_TYPE_LED>;
+ linux,default-trigger = "mmc0";
+ default-state = "on";
+ };
+ };
+
+ i2c_rtc: rtc@68 {
+ compatible = "microcrystal,rv4162";
+ reg = <0x68>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rtc_int>;
+ interrupt-parent = <&gpio7>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+ };
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ clock-frequency = <100000>;
+};
+
+&ldb {
+ lvds-channel@0 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+
+ port@4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie>;
+ reset-gpio = <&gpio2 25 GPIO_ACTIVE_HIGH>;
+ vpcie-supply = <®_pcie>;
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ fsl,uart-has-rtscts;
+};
+
+&usbh1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1>;
+ disable-over-current;
+};
+
+&usbotg {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ vbus-supply = <®_usbotg_vbus>;
+ disable-over-current;
+ dr_mode = "otg";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio6 31 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+};
+
+&iomuxc {
+ pinctrl_en_switch: enswitchgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_DA4__GPIO3_IO04 0xb0b1
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_7__FLEXCAN1_TX 0x1b008
+ MX6QDL_PAD_GPIO_8__FLEXCAN1_RX 0x1b0b0
+ >;
+ };
+
+ pinctrl_flexcan1_en: flexcan1engrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0xb0b1
+ >;
+ };
+
+ pinctrl_hdmicec: hdmicecgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_panel_en: panelengrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0xb0b1
+ >;
+ };
+
+ pinctrl_pcie: pciegrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_OE__GPIO2_IO25 0xb0b1
+ >;
+ };
+
+ pinctrl_pcie_reg: pcievgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0xb0b1
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_rtc_int: rtcintgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x1b0b0
+ >;
+ };
+
+ pinctrl_stmpe: stmpe {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b088
+ MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_EB3__UART3_CTS_B 0x1b0b1
+ MX6QDL_PAD_EIM_D23__UART3_RTS_B 0x1b0b1
+ MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbh1: usbh1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_EB1__GPIO2_IO29 0xb0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ >;
+ };
+
+ pinctrl_usbotg_vbus: usbotg-vbusgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x1b010
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x1b011
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x1b008
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x1b008
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x1b008
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x1b008
+ MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0xb0b1 /* CD */
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6qp-phytec-nunki-rdk-nand.dts b/arch/arm/boot/dts/imx6qp-phytec-nunki-rdk-nand.dts
new file mode 100644
index 000000000000..fdca59807cb0
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qp-phytec-nunki-rdk-nand.dts
@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: GPL-2.0 OR X11
+/*
+ * Copyright (C) 2020 Pengutronix, Marco Felsch <kernel@pengutronix.de>
+ */
+
+/dts-v1/;
+#include "imx6qp.dtsi"
+#include "imx6qdl-phytec-phycore-som.dtsi"
+#include "imx6qdl-phytec-nunki.dtsi"
+
+/ {
+ model = "PHYTEC phyBOARD-Nunki QuadPlus Carrier-Board with NAND";
+ compatible = "phytec,imx6qp-pbac11-nand", "phytec,imx6qp-pbac11",
+ "phytec,imx6qdl-pcm058", "fsl,imx6qp";
+};
+
+&can1 {
+ status = "okay";
+};
+
+&fec {
+ status = "okay";
+};
+
+&gpmi {
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+};
+
+&i2c2 {
+ status = "okay";
+};
+
+&m25p80 {
+ status = "okay";
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&usbh1 {
+ status = "okay";
+};
+
+&usbotg {
+ status = "okay";
+};
+
+&usdhc1 {
+ status = "okay";
+};
--
2.20.1
next prev parent reply other threads:[~2020-10-07 13:31 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-10-07 13:30 [PATCH 1/2] dt-bindings: arm: fsl: add Phytec Nunki boards Marco Felsch
2020-10-07 13:30 ` Marco Felsch [this message]
2020-10-07 13:35 ` [PATCH 2/2] ARM: dts: imx6: Add support for phyBOARD-Nunki Marco Felsch
2020-10-14 7:07 ` Stefan Riedmüller
2020-10-07 13:34 ` [PATCH 1/2] dt-bindings: arm: fsl: add Phytec Nunki boards Marco Felsch
2020-10-14 7:07 ` Stefan Riedmüller
2020-10-07 16:10 ` Rob Herring
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201007133037.25315-2-m.felsch@pengutronix.de \
--to=m.felsch@pengutronix.de \
--cc=devicetree@vger.kernel.org \
--cc=festevam@gmail.com \
--cc=kernel@pengutronix.de \
--cc=linux-imx@nxp.com \
--cc=m.podolszki@phytec.de \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).