* [PATCH 2/5] dt-bindings: panel: add documentation for oneplus6 panel [not found] <20201007171807.285298-1-caleb@connolly.tech> @ 2020-10-07 17:20 ` Caleb Connolly 2020-10-07 17:20 ` [PATCH 3/5] arm64: dts: sdm845: add oneplus 6/t devices Caleb Connolly 2020-10-07 17:20 ` [PATCH 4/5] dt-bindings: add vendor bindings for OnePlus Caleb Connolly 2 siblings, 0 replies; 9+ messages in thread From: Caleb Connolly @ 2020-10-07 17:20 UTC (permalink / raw) To: Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter, Rob Herring, Caleb Connolly Cc: ~postmarketos/upstreaming, dri-devel, devicetree, linux-kernel Document the OnePlus 6/T common panel driver, example from arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi Signed-off-by: Caleb Connolly <caleb@connolly.tech> --- .../display/panel/panel-oneplus6.yaml | 73 +++++++++++++++++++ 1 file changed, 73 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/panel-oneplus6.yaml diff --git a/Documentation/devicetree/bindings/display/panel/panel-oneplus6.yaml b/Documentation/devicetree/bindings/display/panel/panel-oneplus6.yaml new file mode 100644 index 000000000000..23ba369cc2f5 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/panel-oneplus6.yaml @@ -0,0 +1,73 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/panel-oneplus6.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OnePlus 6/T panel driver + +description: | + The OnePlus 6 panel driver encompasses the display panels found in the + OnePlus 6 and 6T devices, the panels have almost identical behaviour and + are not used by any other devices. + +maintainers: + - Caleb Connolly <caleb@connolly.tech> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + enum: + - samsung,sofef00 + - samsung,s6e3fc2x01 + + reg: true + reset-gpios: true + port: true + + vddio-supply: + description: VDDIO regulator + +required: + - compatible + - reset-gpios + - vddio-supply + - port + +unevaluatedProperties: false + +examples: + - | + &dsi0 { + status = "okay"; + vdda-supply = <&vdda_mipi_dsi0_1p2>; + + #address-cells = <1>; + #size-cells = <0>; + + display_panel: panel@0 { + status = "okay"; + compatible = "samsung,sofef00"; + + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + vddio-supply = <&vreg_l14a_1p88>; + + reset-gpios = <&tlmm 6 GPIO_ACTIVE_HIGH>; + + pinctrl-names = "default"; + pinctrl-0 = <&panel_reset_pins &panel_te_pin &panel_esd_pin>; + + port { + panel_in: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + }; + }; + +... -- 2.28.0 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 3/5] arm64: dts: sdm845: add oneplus 6/t devices [not found] <20201007171807.285298-1-caleb@connolly.tech> 2020-10-07 17:20 ` [PATCH 2/5] dt-bindings: panel: add documentation for oneplus6 panel Caleb Connolly @ 2020-10-07 17:20 ` Caleb Connolly 2020-10-07 17:20 ` [PATCH 4/5] dt-bindings: add vendor bindings for OnePlus Caleb Connolly 2 siblings, 0 replies; 9+ messages in thread From: Caleb Connolly @ 2020-10-07 17:20 UTC (permalink / raw) To: Andy Gross, Bjorn Andersson, Rob Herring, Kees Cook, Anton Vorontsov, Colin Cross, Tony Luck Cc: ~postmarketos/upstreaming, Caleb Connolly, linux-arm-msm, devicetree, linux-kernel Add initial support for the OnePlus 6 (enchilada) and 6T (fajita) based on the sdm845-mtp DT. Support includes: * Both display panels work * Touch screen support with rmi4 * RTC support * Remoteprocs boot and can be interacted with over QRTR. * WLAN + Bluetooth both work, although bluetooth doesn't appear in rfkill. * Volume / power buttons and OnePlus Tri-State switch are functional * USB gadget support is forced as it doesn't seem to be able to detect USB cable connect/disconnect, perhaps to do with OnePlus' propriatery fast charge IC. The device successfully boots into Phosh using postmarketOS. Signed-off-by: Caleb Connolly <caleb@connolly.tech> --- arch/arm64/boot/dts/qcom/Makefile | 2 + .../boot/dts/qcom/sdm845-oneplus-common.dtsi | 860 ++++++++++++++++++ .../dts/qcom/sdm845-oneplus-enchilada.dts | 19 + .../boot/dts/qcom/sdm845-oneplus-fajita.dts | 19 + 4 files changed, 900 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi create mode 100644 arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts create mode 100644 arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index d8f1466e6758..a14f246e2367 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -30,6 +30,8 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r2.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r3.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb +dtb-$(CONFIG_ARCH_QCOM) += sdm845-oneplus-enchilada.dtb +dtb-$(CONFIG_ARCH_QCOM) += sdm845-oneplus-fajita.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm850-lenovo-yoga-c630.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8150-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8250-mtp.dtb diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi b/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi new file mode 100644 index 000000000000..b0b09fe94f20 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi @@ -0,0 +1,860 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * SDM845 OnePlus 6(T) (enchilada / fajita) common device tree source + * + * Copyright (c) 2020, The Linux Foundation. All rights reserved. + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include <dt-bindings/input/linux-event-codes.h> +#include "sdm845.dtsi" + +// Needed for some GPIO (like the volume buttons) +#include "pm8998.dtsi" + +// For LEDs +#include "pmi8998.dtsi" + +/ { + + aliases { + hsuart0 = &uart6; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + }; + + /* + * Apparently RPMh does not provide support for PM8998 S4 because it + * is always-on; model it as a fixed regulator. + */ + vreg_s4a_1p8: pm8998-smps4 { + compatible = "regulator-fixed"; + regulator-name = "vreg_s4a_1p8"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-always-on; + regulator-boot-on; + + vin-supply = <&vph_pwr>; + }; + + gpio_tristate_key: gpio-keys { + compatible = "gpio-keys"; + label = "Tri-state key"; + + pinctrl-names = "default"; + pinctrl-0 = <&tri_state_key_default>; + + state-top { + label = "Tri-state key top"; + linux,code = <KEY_A>; + // gpios = <&tlmm 40 GPIO_ACTIVE_LOW>; + interrupt-parent = <&tlmm>; + interrupts = <24 IRQ_TYPE_EDGE_FALLING>; + debounce-interval = <500>; + linux,can-disable; + }; + + state-middle { + label = "Tri-state key middle"; + linux,code = <KEY_B>; + // gpios = <&tlmm 42 GPIO_ACTIVE_LOW>; + interrupt-parent = <&tlmm>; + interrupts = <52 IRQ_TYPE_EDGE_FALLING>; + debounce-interval = <500>; + linux,can-disable; + }; + + state-bottom { + label = "Tri-state key bottom"; + linux,code = <KEY_C>; + // gpios = <&tlmm 26 GPIO_ACTIVE_LOW>; + interrupt-parent = <&tlmm>; + interrupts = <126 IRQ_TYPE_EDGE_FALLING>; + debounce-interval = <500>; + linux,can-disable; + }; + }; + + gpio_vol_keys: gpio-keys { + compatible = "gpio-keys"; + label = "Volume keys"; + autorepeat; + + pinctrl-names = "default"; + pinctrl-0 = <&volume_down_gpio &volume_up_gpio>; + + vol-down { + label = "Volume down"; + linux,code = <KEY_VOLUMEDOWN>; + gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>; + debounce-interval = <15>; + }; + + vol-up { + label = "Volume up"; + linux,code = <KEY_VOLUMEUP>; + gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>; + debounce-interval = <15>; + }; + }; + + extcon_usb1: extcon-usb-1 { + compatible = "linux,extcon-usb-gpio"; + id-gpio = <&tlmm 38 GPIO_ACTIVE_HIGH>; + }; +}; + +&apps_rsc { + pm8998-rpmh-regulators { + compatible = "qcom,pm8998-rpmh-regulators"; + qcom,pmic-id = "a"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + vdd-s7-supply = <&vph_pwr>; + vdd-s8-supply = <&vph_pwr>; + vdd-s9-supply = <&vph_pwr>; + vdd-s10-supply = <&vph_pwr>; + vdd-s11-supply = <&vph_pwr>; + vdd-s12-supply = <&vph_pwr>; + vdd-s13-supply = <&vph_pwr>; + vdd-l1-l27-supply = <&vreg_s7a_1p025>; + vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>; + vdd-l3-l11-supply = <&vreg_s7a_1p025>; + vdd-l4-l5-supply = <&vreg_s7a_1p025>; + vdd-l6-supply = <&vph_pwr>; + vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>; + vdd-l9-supply = <&vreg_bob>; + vdd-l10-l23-l25-supply = <&vreg_bob>; + vdd-l13-l19-l21-supply = <&vreg_bob>; + vdd-l16-l28-supply = <&vreg_bob>; + vdd-l18-l22-supply = <&vreg_bob>; + vdd-l20-l24-supply = <&vreg_bob>; + vdd-l26-supply = <&vreg_s3a_1p35>; + vin-lvs-1-2-supply = <&vreg_s4a_1p8>; + + vreg_s2a_1p125: smps2 { + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + }; + + vreg_s3a_1p35: smps3 { + regulator-min-microvolt = <1352000>; + regulator-max-microvolt = <1352000>; + }; + + vreg_s5a_2p04: smps5 { + regulator-min-microvolt = <1904000>; + regulator-max-microvolt = <2040000>; + }; + + vreg_s7a_1p025: smps7 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1028000>; + }; + + vdd_qusb_hs0: + vdda_hp_pcie_core: + vdda_mipi_csi0_0p9: + vdda_mipi_csi1_0p9: + vdda_mipi_csi2_0p9: + vdda_mipi_dsi0_pll: + vdda_mipi_dsi1_pll: + vdda_qlink_lv: + vdda_qlink_lv_ck: + vdda_qrefs_0p875: + vdda_pcie_core: + vdda_pll_cc_ebi01: + vdda_pll_cc_ebi23: + vdda_sp_sensor: + vdda_ufs1_core: + vdda_ufs2_core: + vdda_usb1_ss_core: + vdda_usb2_ss_core: + vreg_l1a_0p875: ldo1 { + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vddpx_10: + vreg_l2a_1p2: ldo2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-always-on; + }; + + vreg_l3a_1p0: ldo3 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdd_wcss_cx: + vdd_wcss_mx: + vdda_wcss_pll: + vreg_l5a_0p8: ldo5 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vddpx_13: + vreg_l6a_1p8: ldo6 { + regulator-min-microvolt = <1856000>; + regulator-max-microvolt = <1856000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7a_1p8: ldo7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8a_1p2: ldo8 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1248000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9a_1p8: ldo9 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <2928000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l10a_1p8: ldo10 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <2928000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l11a_1p0: ldo11 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1048000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdd_qfprom: + vdd_qfprom_sp: + vdda_apc1_cs_1p8: + vdda_gfx_cs_1p8: + vdda_qrefs_1p8: + vdda_qusb_hs0_1p8: + vddpx_11: + vreg_l12a_1p8: ldo12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vddpx_2: + vreg_l13a_2p95: ldo13 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l14a_1p88: ldo14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-always-on; + }; + + vreg_l15a_1p8: ldo15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l16a_2p7: ldo16 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2704000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l17a_1p3: ldo17 { + regulator-min-microvolt = <1304000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l18a_2p7: ldo18 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l19a_3p0: ldo19 { + regulator-min-microvolt = <2856000>; + regulator-max-microvolt = <3104000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l20a_2p95: ldo20 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l21a_2p95: ldo21 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l22a_2p85: ldo22 { + regulator-min-microvolt = <2864000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l23a_3p3: ldo23 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdda_qusb_hs0_3p1: + vreg_l24a_3p075: ldo24 { + regulator-min-microvolt = <3088000>; + regulator-max-microvolt = <3088000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l25a_3p3: ldo25 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdda_hp_pcie_1p2: + vdda_hv_ebi0: + vdda_hv_ebi1: + vdda_hv_ebi2: + vdda_hv_ebi3: + vdda_mipi_csi_1p25: + vdda_mipi_dsi0_1p2: + vdda_mipi_dsi1_1p2: + vdda_pcie_1p2: + vdda_ufs1_1p2: + vdda_ufs2_1p2: + vdda_usb1_ss_1p2: + vdda_usb2_ss_1p2: + vreg_l26a_1p2: ldo26 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l28a_3p0: ldo28 { + regulator-min-microvolt = <2856000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_lvs1a_1p8: lvs1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_lvs2a_1p8: lvs2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + }; + + pmi8998-rpmh-regulators { + compatible = "qcom,pmi8998-rpmh-regulators"; + qcom,pmic-id = "b"; + + vdd-bob-supply = <&vph_pwr>; + + vreg_bob: bob { + regulator-min-microvolt = <3312000>; + regulator-max-microvolt = <3600000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; + regulator-allow-bypass; + }; + }; + + pm8005-rpmh-regulators { + compatible = "qcom,pm8005-rpmh-regulators"; + qcom,pmic-id = "c"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + + vreg_s3c_0p6: smps3 { + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <600000>; + }; + }; +}; + +/* Reserved memory changes */ +/* + * The rmtfs memory region in downstream is 'dynamically allocated' + * but given the same address every time. hard code it here as this address is + * where the modem firmware expects it to be. + */ +/delete-node/ &rmtfs_mem; + +/ { + reserved-memory { + rmtfs_mem: memory@f5b01000 { + compatible = "qcom,rmtfs-mem"; + reg = <0 0xf5b01000 0 0x200000>; + no-map; + + qcom,client-id = <1>; + qcom,vmid = <15>; + }; + + /* + * This must be reserved as the device will + * crash if memory is allocated here. + */ + removed_region: memory@88f00000 { + no-map; + reg = <0 0x88f00000 0 0x1c00000>; + }; + + ramoops: ramoops@ac300000 { + compatible = "ramoops"; + reg = <0 0xac300000 0 0x400000>; + record-size = <0x40000>; + console-size = <0x40000>; + ftrace-size = <0x40000>; + pmsg-size = <0x200000>; + devinfo-size = <0x1000>; + ecc-size = <16>; + }; + }; +}; + +&gcc { + protected-clocks = <GCC_QSPI_CORE_CLK>, + <GCC_QSPI_CORE_CLK_SRC>, + <GCC_QSPI_CNOC_PERIPH_AHB_CLK>, + <GCC_LPASS_Q6_AXI_CLK>, + <GCC_LPASS_SWAY_CLK>; +}; + +&gpu { + zap-shader { + memory-region = <&gpu_mem>; + firmware-name = "qcom/sdm845/oneplus6/a630_zap.mbn"; + }; +}; + +&adsp_pas { + status = "okay"; + firmware-name = "qcom/sdm845/oneplus6/adsp.mbn"; +}; + +&cdsp_pas { + status = "okay"; + firmware-name = "qcom/sdm845/oneplus6/cdsp.mbn"; +}; + +/* Modem/wifi*/ +&mss_pil { + status = "okay"; + firmware-name = "qcom/sdm845/oneplus6/mba.mbn", "qcom/sdm845/oneplus6/modem.mbn"; +}; + +&uart6 { + status = "okay"; + + bluetooth { + compatible = "qcom,wcn3990-bt"; + + /* In subdir qca/ in /lib/firmware */ + firmware-name = "oneplus6/crnv21.bin"; + + vddio-supply = <&vreg_s4a_1p8>; + vddxo-supply = <&vreg_l7a_1p8>; + vddrf-supply = <&vreg_l17a_1p3>; + vddch0-supply = <&vreg_l25a_3p3>; + max-speed = <3200000>; + }; +}; + +&qup_uart6_default { + pinmux { + pins = "gpio45", "gpio46", "gpio47", "gpio48"; + function = "qup6"; + }; + + cts { + pins = "gpio45"; + bias-pull-down; + }; + + rts-tx { + pins = "gpio46", "gpio47"; + drive-strength = <2>; + bias-disable; + }; + + rx { + pins = "gpio48"; + bias-pull-up; + }; +}; + +&ufs_mem_hc { + status = "okay"; + + reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>; + + vcc-supply = <&vreg_l20a_2p95>; + vcc-max-microamp = <600000>; +}; + +&ufs_mem_phy { + status = "okay"; + + vdda-phy-supply = <&vdda_ufs1_core>; + vdda-pll-supply = <&vdda_ufs1_1p2>; +}; + +&usb_1 { + status = "okay"; + + /* disable USB3 clock requirement as we are in USB 2 mode */ + qcom,select-utmi-as-pipe-clk; +}; + +&usb_1_dwc3 { + /* + * Can't detect USB cable being plugged / unplugged, so this is needed + * for gadget mode + */ + dr_mode = "peripheral"; + + /* fastest mode for USB 2 */ + maximum-speed = "high-speed"; + + extcon = <&extcon_usb1>; + + /* Remove USB3 phy */ + phys = <&usb_1_hsphy>; + phy-names = "usb2-phy"; +}; + +&usb_1_hsphy { + status = "okay"; + + vdd-supply = <&vdda_usb1_ss_core>; + vdda-pll-supply = <&vdda_qusb_hs0_1p8>; + vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>; + + qcom,imp-res-offset-value = <8>; + qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>; + qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>; + qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>; +}; + +&wifi { + status = "okay"; + vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>; + vdd-1.8-xo-supply = <&vreg_l7a_1p8>; + vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; + vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; + + qcom,snoc-host-cap-8bit-quirk; +}; + +&mdss { + status = "okay"; +}; + +&mdss_mdp { + status = "okay"; +}; + +&dsi0 { + status = "okay"; + vdda-supply = <&vdda_mipi_dsi0_1p2>; + + #address-cells = <1>; + #size-cells = <0>; + + display_panel: panel@0 { + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + vddio-supply = <&vreg_l14a_1p88>; + + reset-gpios = <&tlmm 6 GPIO_ACTIVE_HIGH>; + + pinctrl-names = "default"; + pinctrl-0 = <&panel_reset_pins &panel_te_pin &panel_esd_pin>; + + + port { + panel_in: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + }; +}; + +&dsi0_out { + remote-endpoint = <&panel_in>; + data-lanes = <0 1 2 3>; +}; + +&dsi0_phy { + status = "okay"; + vdds-supply = <&vdda_mipi_dsi0_pll>; +}; + +/* GENI device - does i2c, uart, spi and all that stuff */ +&qupv3_id_1 { + status = "okay"; +}; + +&qupv3_id_0 { + status = "okay"; +}; + +&i2c10 { + status = "okay"; + clock-frequency = <100000>; + + bq27541_battery: bq27541-battery@55 { + status = "okay"; + compatible = "ti,bq27541"; + reg = <0x55>; + }; +}; + +&i2c12 { + status = "okay"; + + touchscreen: synaptics-rmi4-i2c@20 { + compatible = "syna,rmi4-i2c"; + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts-extended = <&tlmm 125 0x2008>; // IRQF_ONESHOT | IRQF_TRIGGER_LOW + + pinctrl-names = "default"; + pinctrl-0 = <&ts_default_pins &ts_enable_1p8>; + + vdd-supply = <&vreg_l28a_3p0>; + vio-supply = <&vreg_l6a_1p8>; + + syna,reset-delay-ms = <200>; + syna,startup-delay-ms = <200>; + + rmi4-f01@1 { + reg = <0x01>; + syna,nosleep-mode = <1>; + }; + + rmi4_f12: rmi4-f12@12 { + reg = <0x12>; + touchscreen-x-mm = <68>; + touchscreen-y-mm = <144>; + syna,sensor-type = <1>; + syna,rezero-wait-ms = <200>; + }; + }; +}; + +/* PINCTRL - additions to nodes defined in sdm845.dtsi */ + +&qup_i2c12_default { + mux { + pins = "gpio49", "gpio50"; + function = "qup12"; + }; + config { + pins = "gpio49", "gpio50"; + drive-strength = <2>; + bias-disable; + }; +}; + +&qup_i2c10_default { + pinconf { + pins = "gpio55", "gpio56"; + drive-strength = <2>; + bias-disable; + }; +}; + +&qup_uart9_default { + pinconf-tx { + pins = "gpio4"; + drive-strength = <2>; + bias-disable; + }; + + pinconf-rx { + pins = "gpio5"; + drive-strength = <2>; + bias-pull-up; + }; +}; + +&pm8998_gpio { + volume_down_gpio: pm8998_gpio5 { + pinconf { + pins = "gpio5"; + function = "normal"; + input-enable; + bias-pull-up; + qcom,drive-strength = <0>; + }; + }; + + volume_up_gpio: pm8998_gpio6 { + pinconf { + pins = "gpio6"; + function = "normal"; + input-enable; + bias-pull-up; + qcom,drive-strength = <0>; + }; + }; +}; + +&tlmm { + gpio-reserved-ranges = <0 4>, <81 4>; + + sdc2_clk: sdc2-clk { + pinconf { + pins = "sdc2_clk"; + bias-disable; + + /* + * It seems that mmc_test reports errors if drive + * strength is not 16 on clk, cmd, and data pins. + */ + drive-strength = <16>; + }; + }; + + sdc2_cmd: sdc2-cmd { + pinconf { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <16>; + }; + }; + + sdc2_data: sdc2-data { + pinconf { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <16>; + }; + }; + + tri_state_key_default: tri_state_key_default { + mux { + pins = "gpio40", "gpio42", "gpio26"; + function = "gpio"; + }; + + config { + pins = "gpio40", "gpio42", "gpio26"; + drive-strength = <2>; + bias-disable; + }; + }; + + ts_default_pins: ts-int { + mux { + pins = "gpio99", "gpio125"; + function = "gpio"; + }; + + config { + pins = "gpio99", "gpio125"; + drive-strength = <16>; + bias-pull-up; + }; + }; + + ts_enable_1p8: ts-1p8 { + mux { + pins = "gpio88"; + function = "gpio"; + }; + + config { + pins = "gpio88"; + drive-strength = <16>; + bias-pull-up; + }; + }; + + panel_reset_pins: panel-reset { + mux { + pins = "gpio6", "gpio25", "gpio26"; + function = "gpio"; + }; + + config { + pins = "gpio6", "gpio25", "gpio26"; + drive-strength = <8>; + bias-disable = <0>; + }; + }; + + panel_te_pin: panel-te { + mux { + pins = "gpio10"; + function = "mdp_vsync"; + }; + + config { + pins = "gpio10"; + drive-strength = <2>; + bias-disable; + input-enable; + }; + }; + + panel_esd_pin: panel-esd { + mux { + pins = "gpio30"; + function = "gpio"; + }; + config { + pins = "gpio30"; + drive-strength = <2>; + bias-pull-down; + input-enable; + }; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts b/arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts new file mode 100644 index 000000000000..a62e211a2797 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts @@ -0,0 +1,19 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * SDM845 OnePlus 6 (enchilada) specific device tree + * + * Copyright (c) 2020, The Linux Foundation. All rights reserved. + */ + +#include "sdm845-oneplus-common.dtsi" + +/ { + model = "OnePlus 6"; + compatible = "oneplus,enchilada", "oneplus,oneplus6", "qcom,sdm845"; +}; + +&display_panel { + status = "okay"; + + compatible = "samsung,sofef00"; +}; diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts b/arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts new file mode 100644 index 000000000000..d418389bb2d0 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts @@ -0,0 +1,19 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * SDM845 OnePlus 6T (fajita) specific device tree + * + * Copyright (c) 2020, The Linux Foundation. All rights reserved. + */ + +#include "sdm845-oneplus-common.dtsi" + +/ { + model = "OnePlus 6T"; + compatible = "oneplus,fajita", "oneplus,oneplus6", "qcom,sdm845"; +}; + +&display_panel { + status = "okay"; + + compatible = "samsung,s6e3fc2x01"; +}; -- 2.28.0 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 4/5] dt-bindings: add vendor bindings for OnePlus [not found] <20201007171807.285298-1-caleb@connolly.tech> 2020-10-07 17:20 ` [PATCH 2/5] dt-bindings: panel: add documentation for oneplus6 panel Caleb Connolly 2020-10-07 17:20 ` [PATCH 3/5] arm64: dts: sdm845: add oneplus 6/t devices Caleb Connolly @ 2020-10-07 17:20 ` Caleb Connolly 2 siblings, 0 replies; 9+ messages in thread From: Caleb Connolly @ 2020-10-07 17:20 UTC (permalink / raw) To: Rob Herring, Caleb Connolly Cc: ~postmarketos/upstreaming, Rob Herring, devicetree, linux-kernel Used by the OnePlus 6/T device trees Signed-off-by: Caleb Connolly <caleb@connolly.tech> --- .../bindings/arm/oneplus/oneplus-boards.yaml | 25 +++++++++++++++++++ .../devicetree/bindings/vendor-prefixes.yaml | 2 ++ 2 files changed, 27 insertions(+) create mode 100644 Documentation/devicetree/bindings/arm/oneplus/oneplus-boards.yaml diff --git a/Documentation/devicetree/bindings/arm/oneplus/oneplus-boards.yaml b/Documentation/devicetree/bindings/arm/oneplus/oneplus-boards.yaml new file mode 100644 index 000000000000..a4d9bbd5681f --- /dev/null +++ b/Documentation/devicetree/bindings/arm/oneplus/oneplus-boards.yaml @@ -0,0 +1,25 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/oneplus/oneplus-boards.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OnePlus based boards + +maintainers: + - Caleb Connolly <caleb@connolly.tech> + +properties: + $nodename: + const: '/' + compatible: + oneOf: + - description: SDM845 based boards + items: + - enum: + - oneplus,enchilada # OnePlus 6 + - oneplus,fajita # OnePlus 6T + - const: oneplus,oneplus6 # OnePlus 6 and derivatives + +required: + - compatible diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index 63996ab03521..6672d7242d54 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -754,6 +754,8 @@ patternProperties: description: OLIMEX Ltd. "^olpc,.*": description: One Laptop Per Child + "^oneplus,.*": + description: One Plus Technology (Shenzhen) Co., Ltd.. "^onion,.*": description: Onion Corporation "^onnn,.*": -- 2.28.0 ^ permalink raw reply related [flat|nested] 9+ messages in thread
[parent not found: <20201007174736.292968-1-caleb@connolly.tech>]
* [PATCH 3/5] arm64: dts: sdm845: add oneplus 6/t devices [not found] <20201007174736.292968-1-caleb@connolly.tech> @ 2020-10-07 17:49 ` Caleb Connolly 0 siblings, 0 replies; 9+ messages in thread From: Caleb Connolly @ 2020-10-07 17:49 UTC (permalink / raw) To: linux-arm-msm, Andy Gross, Bjorn Andersson, Rob Herring, Kees Cook, Anton Vorontsov, Colin Cross, Tony Luck Cc: ~postmarketos/upstreaming, Caleb Connolly, devicetree, linux-kernel Add initial support for the OnePlus 6 (enchilada) and 6T (fajita) based on the sdm845-mtp DT. Support includes: * Both display panels work * Touch screen support with rmi4 * RTC support * Remoteprocs boot and can be interacted with over QRTR. * WLAN + Bluetooth both work, although bluetooth doesn't appear in rfkill. * Volume / power buttons and OnePlus Tri-State switch are functional * USB gadget support is forced as it doesn't seem to be able to detect USB cable connect/disconnect, perhaps to do with OnePlus' propriatery fast charge IC. The device successfully boots into Phosh using postmarketOS. Signed-off-by: Caleb Connolly <caleb@connolly.tech> --- arch/arm64/boot/dts/qcom/Makefile | 2 + .../boot/dts/qcom/sdm845-oneplus-common.dtsi | 860 ++++++++++++++++++ .../dts/qcom/sdm845-oneplus-enchilada.dts | 19 + .../boot/dts/qcom/sdm845-oneplus-fajita.dts | 19 + 4 files changed, 900 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi create mode 100644 arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts create mode 100644 arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index d8f1466e6758..a14f246e2367 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -30,6 +30,8 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r2.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r3.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb +dtb-$(CONFIG_ARCH_QCOM) += sdm845-oneplus-enchilada.dtb +dtb-$(CONFIG_ARCH_QCOM) += sdm845-oneplus-fajita.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm850-lenovo-yoga-c630.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8150-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8250-mtp.dtb diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi b/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi new file mode 100644 index 000000000000..b0b09fe94f20 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi @@ -0,0 +1,860 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * SDM845 OnePlus 6(T) (enchilada / fajita) common device tree source + * + * Copyright (c) 2020, The Linux Foundation. All rights reserved. + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include <dt-bindings/input/linux-event-codes.h> +#include "sdm845.dtsi" + +// Needed for some GPIO (like the volume buttons) +#include "pm8998.dtsi" + +// For LEDs +#include "pmi8998.dtsi" + +/ { + + aliases { + hsuart0 = &uart6; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + }; + + /* + * Apparently RPMh does not provide support for PM8998 S4 because it + * is always-on; model it as a fixed regulator. + */ + vreg_s4a_1p8: pm8998-smps4 { + compatible = "regulator-fixed"; + regulator-name = "vreg_s4a_1p8"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-always-on; + regulator-boot-on; + + vin-supply = <&vph_pwr>; + }; + + gpio_tristate_key: gpio-keys { + compatible = "gpio-keys"; + label = "Tri-state key"; + + pinctrl-names = "default"; + pinctrl-0 = <&tri_state_key_default>; + + state-top { + label = "Tri-state key top"; + linux,code = <KEY_A>; + // gpios = <&tlmm 40 GPIO_ACTIVE_LOW>; + interrupt-parent = <&tlmm>; + interrupts = <24 IRQ_TYPE_EDGE_FALLING>; + debounce-interval = <500>; + linux,can-disable; + }; + + state-middle { + label = "Tri-state key middle"; + linux,code = <KEY_B>; + // gpios = <&tlmm 42 GPIO_ACTIVE_LOW>; + interrupt-parent = <&tlmm>; + interrupts = <52 IRQ_TYPE_EDGE_FALLING>; + debounce-interval = <500>; + linux,can-disable; + }; + + state-bottom { + label = "Tri-state key bottom"; + linux,code = <KEY_C>; + // gpios = <&tlmm 26 GPIO_ACTIVE_LOW>; + interrupt-parent = <&tlmm>; + interrupts = <126 IRQ_TYPE_EDGE_FALLING>; + debounce-interval = <500>; + linux,can-disable; + }; + }; + + gpio_vol_keys: gpio-keys { + compatible = "gpio-keys"; + label = "Volume keys"; + autorepeat; + + pinctrl-names = "default"; + pinctrl-0 = <&volume_down_gpio &volume_up_gpio>; + + vol-down { + label = "Volume down"; + linux,code = <KEY_VOLUMEDOWN>; + gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>; + debounce-interval = <15>; + }; + + vol-up { + label = "Volume up"; + linux,code = <KEY_VOLUMEUP>; + gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>; + debounce-interval = <15>; + }; + }; + + extcon_usb1: extcon-usb-1 { + compatible = "linux,extcon-usb-gpio"; + id-gpio = <&tlmm 38 GPIO_ACTIVE_HIGH>; + }; +}; + +&apps_rsc { + pm8998-rpmh-regulators { + compatible = "qcom,pm8998-rpmh-regulators"; + qcom,pmic-id = "a"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + vdd-s7-supply = <&vph_pwr>; + vdd-s8-supply = <&vph_pwr>; + vdd-s9-supply = <&vph_pwr>; + vdd-s10-supply = <&vph_pwr>; + vdd-s11-supply = <&vph_pwr>; + vdd-s12-supply = <&vph_pwr>; + vdd-s13-supply = <&vph_pwr>; + vdd-l1-l27-supply = <&vreg_s7a_1p025>; + vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>; + vdd-l3-l11-supply = <&vreg_s7a_1p025>; + vdd-l4-l5-supply = <&vreg_s7a_1p025>; + vdd-l6-supply = <&vph_pwr>; + vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>; + vdd-l9-supply = <&vreg_bob>; + vdd-l10-l23-l25-supply = <&vreg_bob>; + vdd-l13-l19-l21-supply = <&vreg_bob>; + vdd-l16-l28-supply = <&vreg_bob>; + vdd-l18-l22-supply = <&vreg_bob>; + vdd-l20-l24-supply = <&vreg_bob>; + vdd-l26-supply = <&vreg_s3a_1p35>; + vin-lvs-1-2-supply = <&vreg_s4a_1p8>; + + vreg_s2a_1p125: smps2 { + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + }; + + vreg_s3a_1p35: smps3 { + regulator-min-microvolt = <1352000>; + regulator-max-microvolt = <1352000>; + }; + + vreg_s5a_2p04: smps5 { + regulator-min-microvolt = <1904000>; + regulator-max-microvolt = <2040000>; + }; + + vreg_s7a_1p025: smps7 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1028000>; + }; + + vdd_qusb_hs0: + vdda_hp_pcie_core: + vdda_mipi_csi0_0p9: + vdda_mipi_csi1_0p9: + vdda_mipi_csi2_0p9: + vdda_mipi_dsi0_pll: + vdda_mipi_dsi1_pll: + vdda_qlink_lv: + vdda_qlink_lv_ck: + vdda_qrefs_0p875: + vdda_pcie_core: + vdda_pll_cc_ebi01: + vdda_pll_cc_ebi23: + vdda_sp_sensor: + vdda_ufs1_core: + vdda_ufs2_core: + vdda_usb1_ss_core: + vdda_usb2_ss_core: + vreg_l1a_0p875: ldo1 { + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vddpx_10: + vreg_l2a_1p2: ldo2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-always-on; + }; + + vreg_l3a_1p0: ldo3 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdd_wcss_cx: + vdd_wcss_mx: + vdda_wcss_pll: + vreg_l5a_0p8: ldo5 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vddpx_13: + vreg_l6a_1p8: ldo6 { + regulator-min-microvolt = <1856000>; + regulator-max-microvolt = <1856000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7a_1p8: ldo7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8a_1p2: ldo8 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1248000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9a_1p8: ldo9 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <2928000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l10a_1p8: ldo10 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <2928000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l11a_1p0: ldo11 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1048000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdd_qfprom: + vdd_qfprom_sp: + vdda_apc1_cs_1p8: + vdda_gfx_cs_1p8: + vdda_qrefs_1p8: + vdda_qusb_hs0_1p8: + vddpx_11: + vreg_l12a_1p8: ldo12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vddpx_2: + vreg_l13a_2p95: ldo13 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l14a_1p88: ldo14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-always-on; + }; + + vreg_l15a_1p8: ldo15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l16a_2p7: ldo16 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2704000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l17a_1p3: ldo17 { + regulator-min-microvolt = <1304000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l18a_2p7: ldo18 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l19a_3p0: ldo19 { + regulator-min-microvolt = <2856000>; + regulator-max-microvolt = <3104000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l20a_2p95: ldo20 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l21a_2p95: ldo21 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l22a_2p85: ldo22 { + regulator-min-microvolt = <2864000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l23a_3p3: ldo23 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdda_qusb_hs0_3p1: + vreg_l24a_3p075: ldo24 { + regulator-min-microvolt = <3088000>; + regulator-max-microvolt = <3088000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l25a_3p3: ldo25 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdda_hp_pcie_1p2: + vdda_hv_ebi0: + vdda_hv_ebi1: + vdda_hv_ebi2: + vdda_hv_ebi3: + vdda_mipi_csi_1p25: + vdda_mipi_dsi0_1p2: + vdda_mipi_dsi1_1p2: + vdda_pcie_1p2: + vdda_ufs1_1p2: + vdda_ufs2_1p2: + vdda_usb1_ss_1p2: + vdda_usb2_ss_1p2: + vreg_l26a_1p2: ldo26 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l28a_3p0: ldo28 { + regulator-min-microvolt = <2856000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_lvs1a_1p8: lvs1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_lvs2a_1p8: lvs2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + }; + + pmi8998-rpmh-regulators { + compatible = "qcom,pmi8998-rpmh-regulators"; + qcom,pmic-id = "b"; + + vdd-bob-supply = <&vph_pwr>; + + vreg_bob: bob { + regulator-min-microvolt = <3312000>; + regulator-max-microvolt = <3600000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; + regulator-allow-bypass; + }; + }; + + pm8005-rpmh-regulators { + compatible = "qcom,pm8005-rpmh-regulators"; + qcom,pmic-id = "c"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + + vreg_s3c_0p6: smps3 { + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <600000>; + }; + }; +}; + +/* Reserved memory changes */ +/* + * The rmtfs memory region in downstream is 'dynamically allocated' + * but given the same address every time. hard code it here as this address is + * where the modem firmware expects it to be. + */ +/delete-node/ &rmtfs_mem; + +/ { + reserved-memory { + rmtfs_mem: memory@f5b01000 { + compatible = "qcom,rmtfs-mem"; + reg = <0 0xf5b01000 0 0x200000>; + no-map; + + qcom,client-id = <1>; + qcom,vmid = <15>; + }; + + /* + * This must be reserved as the device will + * crash if memory is allocated here. + */ + removed_region: memory@88f00000 { + no-map; + reg = <0 0x88f00000 0 0x1c00000>; + }; + + ramoops: ramoops@ac300000 { + compatible = "ramoops"; + reg = <0 0xac300000 0 0x400000>; + record-size = <0x40000>; + console-size = <0x40000>; + ftrace-size = <0x40000>; + pmsg-size = <0x200000>; + devinfo-size = <0x1000>; + ecc-size = <16>; + }; + }; +}; + +&gcc { + protected-clocks = <GCC_QSPI_CORE_CLK>, + <GCC_QSPI_CORE_CLK_SRC>, + <GCC_QSPI_CNOC_PERIPH_AHB_CLK>, + <GCC_LPASS_Q6_AXI_CLK>, + <GCC_LPASS_SWAY_CLK>; +}; + +&gpu { + zap-shader { + memory-region = <&gpu_mem>; + firmware-name = "qcom/sdm845/oneplus6/a630_zap.mbn"; + }; +}; + +&adsp_pas { + status = "okay"; + firmware-name = "qcom/sdm845/oneplus6/adsp.mbn"; +}; + +&cdsp_pas { + status = "okay"; + firmware-name = "qcom/sdm845/oneplus6/cdsp.mbn"; +}; + +/* Modem/wifi*/ +&mss_pil { + status = "okay"; + firmware-name = "qcom/sdm845/oneplus6/mba.mbn", "qcom/sdm845/oneplus6/modem.mbn"; +}; + +&uart6 { + status = "okay"; + + bluetooth { + compatible = "qcom,wcn3990-bt"; + + /* In subdir qca/ in /lib/firmware */ + firmware-name = "oneplus6/crnv21.bin"; + + vddio-supply = <&vreg_s4a_1p8>; + vddxo-supply = <&vreg_l7a_1p8>; + vddrf-supply = <&vreg_l17a_1p3>; + vddch0-supply = <&vreg_l25a_3p3>; + max-speed = <3200000>; + }; +}; + +&qup_uart6_default { + pinmux { + pins = "gpio45", "gpio46", "gpio47", "gpio48"; + function = "qup6"; + }; + + cts { + pins = "gpio45"; + bias-pull-down; + }; + + rts-tx { + pins = "gpio46", "gpio47"; + drive-strength = <2>; + bias-disable; + }; + + rx { + pins = "gpio48"; + bias-pull-up; + }; +}; + +&ufs_mem_hc { + status = "okay"; + + reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>; + + vcc-supply = <&vreg_l20a_2p95>; + vcc-max-microamp = <600000>; +}; + +&ufs_mem_phy { + status = "okay"; + + vdda-phy-supply = <&vdda_ufs1_core>; + vdda-pll-supply = <&vdda_ufs1_1p2>; +}; + +&usb_1 { + status = "okay"; + + /* disable USB3 clock requirement as we are in USB 2 mode */ + qcom,select-utmi-as-pipe-clk; +}; + +&usb_1_dwc3 { + /* + * Can't detect USB cable being plugged / unplugged, so this is needed + * for gadget mode + */ + dr_mode = "peripheral"; + + /* fastest mode for USB 2 */ + maximum-speed = "high-speed"; + + extcon = <&extcon_usb1>; + + /* Remove USB3 phy */ + phys = <&usb_1_hsphy>; + phy-names = "usb2-phy"; +}; + +&usb_1_hsphy { + status = "okay"; + + vdd-supply = <&vdda_usb1_ss_core>; + vdda-pll-supply = <&vdda_qusb_hs0_1p8>; + vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>; + + qcom,imp-res-offset-value = <8>; + qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>; + qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>; + qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>; +}; + +&wifi { + status = "okay"; + vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>; + vdd-1.8-xo-supply = <&vreg_l7a_1p8>; + vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; + vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; + + qcom,snoc-host-cap-8bit-quirk; +}; + +&mdss { + status = "okay"; +}; + +&mdss_mdp { + status = "okay"; +}; + +&dsi0 { + status = "okay"; + vdda-supply = <&vdda_mipi_dsi0_1p2>; + + #address-cells = <1>; + #size-cells = <0>; + + display_panel: panel@0 { + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + vddio-supply = <&vreg_l14a_1p88>; + + reset-gpios = <&tlmm 6 GPIO_ACTIVE_HIGH>; + + pinctrl-names = "default"; + pinctrl-0 = <&panel_reset_pins &panel_te_pin &panel_esd_pin>; + + + port { + panel_in: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + }; +}; + +&dsi0_out { + remote-endpoint = <&panel_in>; + data-lanes = <0 1 2 3>; +}; + +&dsi0_phy { + status = "okay"; + vdds-supply = <&vdda_mipi_dsi0_pll>; +}; + +/* GENI device - does i2c, uart, spi and all that stuff */ +&qupv3_id_1 { + status = "okay"; +}; + +&qupv3_id_0 { + status = "okay"; +}; + +&i2c10 { + status = "okay"; + clock-frequency = <100000>; + + bq27541_battery: bq27541-battery@55 { + status = "okay"; + compatible = "ti,bq27541"; + reg = <0x55>; + }; +}; + +&i2c12 { + status = "okay"; + + touchscreen: synaptics-rmi4-i2c@20 { + compatible = "syna,rmi4-i2c"; + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts-extended = <&tlmm 125 0x2008>; // IRQF_ONESHOT | IRQF_TRIGGER_LOW + + pinctrl-names = "default"; + pinctrl-0 = <&ts_default_pins &ts_enable_1p8>; + + vdd-supply = <&vreg_l28a_3p0>; + vio-supply = <&vreg_l6a_1p8>; + + syna,reset-delay-ms = <200>; + syna,startup-delay-ms = <200>; + + rmi4-f01@1 { + reg = <0x01>; + syna,nosleep-mode = <1>; + }; + + rmi4_f12: rmi4-f12@12 { + reg = <0x12>; + touchscreen-x-mm = <68>; + touchscreen-y-mm = <144>; + syna,sensor-type = <1>; + syna,rezero-wait-ms = <200>; + }; + }; +}; + +/* PINCTRL - additions to nodes defined in sdm845.dtsi */ + +&qup_i2c12_default { + mux { + pins = "gpio49", "gpio50"; + function = "qup12"; + }; + config { + pins = "gpio49", "gpio50"; + drive-strength = <2>; + bias-disable; + }; +}; + +&qup_i2c10_default { + pinconf { + pins = "gpio55", "gpio56"; + drive-strength = <2>; + bias-disable; + }; +}; + +&qup_uart9_default { + pinconf-tx { + pins = "gpio4"; + drive-strength = <2>; + bias-disable; + }; + + pinconf-rx { + pins = "gpio5"; + drive-strength = <2>; + bias-pull-up; + }; +}; + +&pm8998_gpio { + volume_down_gpio: pm8998_gpio5 { + pinconf { + pins = "gpio5"; + function = "normal"; + input-enable; + bias-pull-up; + qcom,drive-strength = <0>; + }; + }; + + volume_up_gpio: pm8998_gpio6 { + pinconf { + pins = "gpio6"; + function = "normal"; + input-enable; + bias-pull-up; + qcom,drive-strength = <0>; + }; + }; +}; + +&tlmm { + gpio-reserved-ranges = <0 4>, <81 4>; + + sdc2_clk: sdc2-clk { + pinconf { + pins = "sdc2_clk"; + bias-disable; + + /* + * It seems that mmc_test reports errors if drive + * strength is not 16 on clk, cmd, and data pins. + */ + drive-strength = <16>; + }; + }; + + sdc2_cmd: sdc2-cmd { + pinconf { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <16>; + }; + }; + + sdc2_data: sdc2-data { + pinconf { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <16>; + }; + }; + + tri_state_key_default: tri_state_key_default { + mux { + pins = "gpio40", "gpio42", "gpio26"; + function = "gpio"; + }; + + config { + pins = "gpio40", "gpio42", "gpio26"; + drive-strength = <2>; + bias-disable; + }; + }; + + ts_default_pins: ts-int { + mux { + pins = "gpio99", "gpio125"; + function = "gpio"; + }; + + config { + pins = "gpio99", "gpio125"; + drive-strength = <16>; + bias-pull-up; + }; + }; + + ts_enable_1p8: ts-1p8 { + mux { + pins = "gpio88"; + function = "gpio"; + }; + + config { + pins = "gpio88"; + drive-strength = <16>; + bias-pull-up; + }; + }; + + panel_reset_pins: panel-reset { + mux { + pins = "gpio6", "gpio25", "gpio26"; + function = "gpio"; + }; + + config { + pins = "gpio6", "gpio25", "gpio26"; + drive-strength = <8>; + bias-disable = <0>; + }; + }; + + panel_te_pin: panel-te { + mux { + pins = "gpio10"; + function = "mdp_vsync"; + }; + + config { + pins = "gpio10"; + drive-strength = <2>; + bias-disable; + input-enable; + }; + }; + + panel_esd_pin: panel-esd { + mux { + pins = "gpio30"; + function = "gpio"; + }; + config { + pins = "gpio30"; + drive-strength = <2>; + bias-pull-down; + input-enable; + }; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts b/arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts new file mode 100644 index 000000000000..a62e211a2797 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts @@ -0,0 +1,19 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * SDM845 OnePlus 6 (enchilada) specific device tree + * + * Copyright (c) 2020, The Linux Foundation. All rights reserved. + */ + +#include "sdm845-oneplus-common.dtsi" + +/ { + model = "OnePlus 6"; + compatible = "oneplus,enchilada", "oneplus,oneplus6", "qcom,sdm845"; +}; + +&display_panel { + status = "okay"; + + compatible = "samsung,sofef00"; +}; diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts b/arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts new file mode 100644 index 000000000000..d418389bb2d0 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts @@ -0,0 +1,19 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * SDM845 OnePlus 6T (fajita) specific device tree + * + * Copyright (c) 2020, The Linux Foundation. All rights reserved. + */ + +#include "sdm845-oneplus-common.dtsi" + +/ { + model = "OnePlus 6T"; + compatible = "oneplus,fajita", "oneplus,oneplus6", "qcom,sdm845"; +}; + +&display_panel { + status = "okay"; + + compatible = "samsung,s6e3fc2x01"; +}; -- 2.28.0 ^ permalink raw reply related [flat|nested] 9+ messages in thread
[parent not found: <20201112161920.2671430-1-caleb@connolly.tech>]
* [PATCH 3/5] arm64: dts: sdm845: add oneplus 6/t devices [not found] <20201112161920.2671430-1-caleb@connolly.tech> @ 2020-11-12 16:21 ` Caleb Connolly 2020-11-16 22:01 ` Pavel Machek 2020-11-21 4:28 ` Bjorn Andersson 0 siblings, 2 replies; 9+ messages in thread From: Caleb Connolly @ 2020-11-12 16:21 UTC (permalink / raw) To: linux-arm-msm, Andy Gross, Bjorn Andersson, Rob Herring, Kees Cook, Anton Vorontsov, Colin Cross, Tony Luck Cc: phone-devel, ~postmarketos/upstreaming, Caleb Connolly, devicetree, linux-kernel Add initial support for the OnePlus 6 (enchilada) and 6T (fajita) based on the sdm845-mtp DT. Support includes: * Display panels and Adreno 630 * Touch screen support with synaptics rmi4 * All remoteprocs start correctly * WLAN / Bluetooth * Volume / power buttons and OnePlus Tri-State switch are functional The tri-state switch is a 3 state mute slider on the side of the phone * USB support, currently forced to peripheral as type C detection isn't functional. Support for this device depends on the following series: https://lore.kernel.org/linux-iommu/20201017043907.2656013-1-bjorn.andersson@linaro.org/ Signed-off-by: Caleb Connolly <caleb@connolly.tech> --- Changes since v1 * Remove unused pinctrl nodes * Properly model touchscreen vio supply GPIO * Improve comments * Remove bq27541 battery as it doesn't work --- arch/arm64/boot/dts/qcom/Makefile | 2 + .../boot/dts/qcom/sdm845-oneplus-common.dtsi | 822 ++++++++++++++++++ .../dts/qcom/sdm845-oneplus-enchilada.dts | 19 + .../boot/dts/qcom/sdm845-oneplus-fajita.dts | 23 + 4 files changed, 866 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi create mode 100644 arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts create mode 100644 arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index fb4631f898fd..f45eddfb7dc5 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -40,6 +40,8 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r3.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-xiaomi-beryllium.dtb +dtb-$(CONFIG_ARCH_QCOM) += sdm845-oneplus-enchilada.dtb +dtb-$(CONFIG_ARCH_QCOM) += sdm845-oneplus-fajita.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm850-lenovo-yoga-c630.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8150-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8250-mtp.dtb diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi b/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi new file mode 100644 index 000000000000..4e6477f1e574 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi @@ -0,0 +1,822 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * SDM845 OnePlus 6(T) (enchilada / fajita) common device tree source + * + * Copyright (c) 2020, The Linux Foundation. All rights reserved. + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include <dt-bindings/input/linux-event-codes.h> +#include "sdm845.dtsi" + +// Needed for some GPIO (like the volume buttons) +#include "pm8998.dtsi" +#include "pmi8998.dtsi" + +/ { + + aliases { + hsuart0 = &uart6; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + }; + + /* + * Apparently RPMh does not provide support for PM8998 S4 because it + * is always-on; model it as a fixed regulator. + */ + vreg_s4a_1p8: pm8998-smps4 { + compatible = "regulator-fixed"; + regulator-name = "vreg_s4a_1p8"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-always-on; + regulator-boot-on; + + vin-supply = <&vph_pwr>; + }; + + /* + * The touchscreen regulator seems to be controlled somehow by a gpio. + */ + ts_1p8_supply: ts_1v8_regulator { + compatible = "regulator-fixed"; + regulator-name = "ts_1p8_supply"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + gpio = <&tlmm 88 0>; + enable-active-high; + regulator-boot-on; + }; + + gpio_tristate_key: gpio-keys { + compatible = "gpio-keys"; + label = "Tri-state keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&tri_state_key_default>; + + state-top { + label = "Tri-state key top"; + linux,code = <KEY_MACRO1>; + interrupt-parent = <&tlmm>; + interrupts = <24 IRQ_TYPE_EDGE_FALLING>; + debounce-interval = <500>; + linux,can-disable; + }; + + state-middle { + label = "Tri-state key middle"; + linux,code = <KEY_MACRO2>; + interrupt-parent = <&tlmm>; + interrupts = <52 IRQ_TYPE_EDGE_FALLING>; + debounce-interval = <500>; + linux,can-disable; + }; + + state-bottom { + label = "Tri-state key bottom"; + linux,code = <KEY_MACRO3>; + interrupt-parent = <&tlmm>; + interrupts = <126 IRQ_TYPE_EDGE_FALLING>; + debounce-interval = <500>; + linux,can-disable; + }; + }; + + gpio_vol_keys: gpio-keys { + compatible = "gpio-keys"; + label = "Volume keys"; + autorepeat; + + pinctrl-names = "default"; + pinctrl-0 = <&volume_down_gpio &volume_up_gpio>; + + vol-down { + label = "Volume down"; + linux,code = <KEY_VOLUMEDOWN>; + gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>; + debounce-interval = <15>; + }; + + vol-up { + label = "Volume up"; + linux,code = <KEY_VOLUMEUP>; + gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>; + debounce-interval = <15>; + }; + }; + + extcon_usb1_detect: extcon-usb-1 { + compatible = "linux,extcon-usb-gpio"; + id-gpio = <&tlmm 38 GPIO_ACTIVE_HIGH>; + }; +}; + +&apps_rsc { + pm8998-rpmh-regulators { + compatible = "qcom,pm8998-rpmh-regulators"; + qcom,pmic-id = "a"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + vdd-s7-supply = <&vph_pwr>; + vdd-s8-supply = <&vph_pwr>; + vdd-s9-supply = <&vph_pwr>; + vdd-s10-supply = <&vph_pwr>; + vdd-s11-supply = <&vph_pwr>; + vdd-s12-supply = <&vph_pwr>; + vdd-s13-supply = <&vph_pwr>; + vdd-l1-l27-supply = <&vreg_s7a_1p025>; + vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>; + vdd-l3-l11-supply = <&vreg_s7a_1p025>; + vdd-l4-l5-supply = <&vreg_s7a_1p025>; + vdd-l6-supply = <&vph_pwr>; + vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>; + vdd-l9-supply = <&vreg_bob>; + vdd-l10-l23-l25-supply = <&vreg_bob>; + vdd-l13-l19-l21-supply = <&vreg_bob>; + vdd-l16-l28-supply = <&vreg_bob>; + vdd-l18-l22-supply = <&vreg_bob>; + vdd-l20-l24-supply = <&vreg_bob>; + vdd-l26-supply = <&vreg_s3a_1p35>; + vin-lvs-1-2-supply = <&vreg_s4a_1p8>; + + vreg_s2a_1p125: smps2 { + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + }; + + vreg_s3a_1p35: smps3 { + regulator-min-microvolt = <1352000>; + regulator-max-microvolt = <1352000>; + }; + + vreg_s5a_2p04: smps5 { + regulator-min-microvolt = <1904000>; + regulator-max-microvolt = <2040000>; + }; + + vreg_s7a_1p025: smps7 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1028000>; + }; + + vdd_qusb_hs0: + vdda_hp_pcie_core: + vdda_mipi_csi0_0p9: + vdda_mipi_csi1_0p9: + vdda_mipi_csi2_0p9: + vdda_mipi_dsi0_pll: + vdda_mipi_dsi1_pll: + vdda_qlink_lv: + vdda_qlink_lv_ck: + vdda_qrefs_0p875: + vdda_pcie_core: + vdda_pll_cc_ebi01: + vdda_pll_cc_ebi23: + vdda_sp_sensor: + vdda_ufs1_core: + vdda_ufs2_core: + vdda_usb1_ss_core: + vdda_usb2_ss_core: + vreg_l1a_0p875: ldo1 { + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vddpx_10: + vreg_l2a_1p2: ldo2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-always-on; + }; + + vreg_l3a_1p0: ldo3 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdd_wcss_cx: + vdd_wcss_mx: + vdda_wcss_pll: + vreg_l5a_0p8: ldo5 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vddpx_13: + vreg_l6a_1p8: ldo6 { + regulator-min-microvolt = <1856000>; + regulator-max-microvolt = <1856000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7a_1p8: ldo7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8a_1p2: ldo8 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1248000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9a_1p8: ldo9 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <2928000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l10a_1p8: ldo10 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <2928000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l11a_1p0: ldo11 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1048000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdd_qfprom: + vdd_qfprom_sp: + vdda_apc1_cs_1p8: + vdda_gfx_cs_1p8: + vdda_qrefs_1p8: + vdda_qusb_hs0_1p8: + vddpx_11: + vreg_l12a_1p8: ldo12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vddpx_2: + vreg_l13a_2p95: ldo13 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l14a_1p88: ldo14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-always-on; + }; + + vreg_l15a_1p8: ldo15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l16a_2p7: ldo16 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2704000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l17a_1p3: ldo17 { + regulator-min-microvolt = <1304000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l18a_2p7: ldo18 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l19a_3p0: ldo19 { + regulator-min-microvolt = <2856000>; + regulator-max-microvolt = <3104000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l20a_2p95: ldo20 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l21a_2p95: ldo21 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l22a_2p85: ldo22 { + regulator-min-microvolt = <2864000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l23a_3p3: ldo23 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdda_qusb_hs0_3p1: + vreg_l24a_3p075: ldo24 { + regulator-min-microvolt = <3088000>; + regulator-max-microvolt = <3088000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l25a_3p3: ldo25 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdda_hp_pcie_1p2: + vdda_hv_ebi0: + vdda_hv_ebi1: + vdda_hv_ebi2: + vdda_hv_ebi3: + vdda_mipi_csi_1p25: + vdda_mipi_dsi0_1p2: + vdda_mipi_dsi1_1p2: + vdda_pcie_1p2: + vdda_ufs1_1p2: + vdda_ufs2_1p2: + vdda_usb1_ss_1p2: + vdda_usb2_ss_1p2: + vreg_l26a_1p2: ldo26 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l28a_3p0: ldo28 { + regulator-min-microvolt = <2856000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_lvs1a_1p8: lvs1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_lvs2a_1p8: lvs2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + }; + + pmi8998-rpmh-regulators { + compatible = "qcom,pmi8998-rpmh-regulators"; + qcom,pmic-id = "b"; + + vdd-bob-supply = <&vph_pwr>; + + vreg_bob: bob { + regulator-min-microvolt = <3312000>; + regulator-max-microvolt = <3600000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; + regulator-allow-bypass; + }; + }; + + pm8005-rpmh-regulators { + compatible = "qcom,pm8005-rpmh-regulators"; + qcom,pmic-id = "c"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + + vreg_s3c_0p6: smps3 { + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <600000>; + }; + }; +}; + +/* Reserved memory changes */ +/delete-node/ &rmtfs_mem; + +/ { + reserved-memory { + /* + * The rmtfs memory region in downstream is 'dynamically allocated' + * but given the same address every time. Hard code it as this address is + * where the modem firmware expects it to be. + */ + rmtfs_mem: memory@f5b01000 { + compatible = "qcom,rmtfs-mem"; + reg = <0 0xf5b01000 0 0x200000>; + no-map; + + qcom,client-id = <1>; + qcom,vmid = <15>; + }; + + /* + * This must be reserved as the device will + * crash if memory is allocated here due to + * vendor quirks. + */ + removed_region: memory@88f00000 { + no-map; + reg = <0 0x88f00000 0 0x1c00000>; + }; + + ramoops: ramoops@ac300000 { + compatible = "ramoops"; + reg = <0 0xac300000 0 0x400000>; + record-size = <0x40000>; + console-size = <0x40000>; + ftrace-size = <0x40000>; + pmsg-size = <0x200000>; + devinfo-size = <0x1000>; + ecc-size = <16>; + }; + }; +}; + +&gcc { + protected-clocks = <GCC_QSPI_CORE_CLK>, + <GCC_QSPI_CORE_CLK_SRC>, + <GCC_QSPI_CNOC_PERIPH_AHB_CLK>, + <GCC_LPASS_Q6_AXI_CLK>, + <GCC_LPASS_SWAY_CLK>; +}; + +&gpu { + zap-shader { + memory-region = <&gpu_mem>; + firmware-name = "qcom/sdm845/oneplus6/a630_zap.mbn"; + }; +}; + +&adsp_pas { + status = "okay"; + firmware-name = "qcom/sdm845/oneplus6/adsp.mbn"; +}; + +&cdsp_pas { + status = "okay"; + firmware-name = "qcom/sdm845/oneplus6/cdsp.mbn"; +}; + +/* Modem/wifi*/ +&mss_pil { + status = "okay"; + firmware-name = "qcom/sdm845/oneplus6/mba.mbn", "qcom/sdm845/oneplus6/modem.mbn"; +}; + +&uart6 { + status = "okay"; + + bluetooth { + compatible = "qcom,wcn3990-bt"; + + /* This path is relative to the qca/ + * subdir under lib/firmware. + */ + firmware-name = "oneplus6/crnv21.bin"; + + vddio-supply = <&vreg_s4a_1p8>; + vddxo-supply = <&vreg_l7a_1p8>; + vddrf-supply = <&vreg_l17a_1p3>; + vddch0-supply = <&vreg_l25a_3p3>; + max-speed = <3200000>; + }; +}; + +&qup_uart6_default { + pinmux { + pins = "gpio45", "gpio46", "gpio47", "gpio48"; + function = "qup6"; + }; + + cts { + pins = "gpio45"; + bias-pull-down; + }; + + rts-tx { + pins = "gpio46", "gpio47"; + drive-strength = <2>; + bias-disable; + }; + + rx { + pins = "gpio48"; + bias-pull-up; + }; +}; + +&ufs_mem_hc { + status = "okay"; + + reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>; + + vcc-supply = <&vreg_l20a_2p95>; + vcc-max-microamp = <600000>; +}; + +&ufs_mem_phy { + status = "okay"; + + vdda-phy-supply = <&vdda_ufs1_core>; + vdda-pll-supply = <&vdda_ufs1_1p2>; +}; + +&usb_1 { + status = "okay"; + + /* + * disable USB3 clock requirement as the device only supports + * USB2. + */ + qcom,select-utmi-as-pipe-clk; +}; + +&usb_1_dwc3 { + /* + * We don't have the capability to switch modes yet. + */ + dr_mode = "peripheral"; + + /* fastest mode for USB 2 */ + maximum-speed = "high-speed"; + + extcon = <&extcon_usb1_detect>; + + /* Remove USB3 phy as it's unused on this device. */ + phys = <&usb_1_hsphy>; + phy-names = "usb2-phy"; +}; + +&usb_1_hsphy { + status = "okay"; + + vdd-supply = <&vdda_usb1_ss_core>; + vdda-pll-supply = <&vdda_qusb_hs0_1p8>; + vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>; + + qcom,imp-res-offset-value = <8>; + qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>; + qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>; + qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>; +}; + +&wifi { + status = "okay"; + vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>; + vdd-1.8-xo-supply = <&vreg_l7a_1p8>; + vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; + vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; + + qcom,snoc-host-cap-8bit-quirk; +}; + +&mdss { + status = "okay"; +}; + +&mdss_mdp { + status = "okay"; +}; + +&dsi0 { + status = "okay"; + vdda-supply = <&vdda_mipi_dsi0_1p2>; + + #address-cells = <1>; + #size-cells = <0>; + + /* + * Both devices use different panels but all other properties + * are common. Compatible line is declared in device dts. + */ + display_panel: panel@0 { + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + vddio-supply = <&vreg_l14a_1p88>; + + reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>; + + pinctrl-names = "default"; + pinctrl-0 = <&panel_reset_pins &panel_te_pin &panel_esd_pin>; + + port { + panel_in: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + }; +}; + +&dsi0_out { + remote-endpoint = <&panel_in>; + data-lanes = <0 1 2 3>; +}; + +&dsi0_phy { + status = "okay"; + vdds-supply = <&vdda_mipi_dsi0_pll>; +}; + +&qupv3_id_1 { + status = "okay"; +}; + +&qupv3_id_0 { + status = "okay"; +}; + +&i2c12 { + status = "okay"; + + touchscreen: synaptics-rmi4-i2c@20 { + compatible = "syna,rmi4-i2c"; + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts-extended = <&tlmm 125 IRQ_TYPE_EDGE_FALLING>; + + pinctrl-names = "default"; + pinctrl-0 = <&ts_default_pins>; + + vdd-supply = <&vreg_l28a_3p0>; + vio-supply = <&ts_1p8_supply>; + + syna,reset-delay-ms = <200>; + syna,startup-delay-ms = <200>; + + rmi4-f01@1 { + reg = <0x01>; + syna,nosleep-mode = <1>; + }; + + rmi4_f12: rmi4-f12@12 { + reg = <0x12>; + touchscreen-x-mm = <68>; + touchscreen-y-mm = <144>; + syna,sensor-type = <1>; + syna,rezero-wait-ms = <200>; + }; + }; +}; + +&qup_i2c12_default { + mux { + pins = "gpio49", "gpio50"; + function = "qup12"; + }; + config { + pins = "gpio49", "gpio50"; + drive-strength = <2>; + bias-disable; + }; +}; + +&qup_i2c10_default { + pinconf { + pins = "gpio55", "gpio56"; + drive-strength = <2>; + bias-disable; + }; +}; + +&qup_uart9_default { + pinconf-tx { + pins = "gpio4"; + drive-strength = <2>; + bias-disable; + }; + + pinconf-rx { + pins = "gpio5"; + drive-strength = <2>; + bias-pull-up; + }; +}; + +&pm8998_gpio { + volume_down_gpio: pm8998_gpio5 { + pinconf { + pins = "gpio5"; + function = "normal"; + input-enable; + bias-pull-up; + qcom,drive-strength = <0>; + }; + }; + + volume_up_gpio: pm8998_gpio6 { + pinconf { + pins = "gpio6"; + function = "normal"; + input-enable; + bias-pull-up; + qcom,drive-strength = <0>; + }; + }; +}; + +&tlmm { + gpio-reserved-ranges = <0 4>, <81 4>; + + tri_state_key_default: tri_state_key_default { + mux { + pins = "gpio40", "gpio42", "gpio26"; + function = "gpio"; + }; + + config { + pins = "gpio40", "gpio42", "gpio26"; + drive-strength = <2>; + bias-disable; + }; + }; + + ts_default_pins: ts-int { + mux { + pins = "gpio99", "gpio125"; + function = "gpio"; + }; + + config { + pins = "gpio99", "gpio125"; + drive-strength = <16>; + bias-pull-up; + }; + }; + + panel_reset_pins: panel-reset { + mux { + pins = "gpio6", "gpio25", "gpio26"; + function = "gpio"; + }; + + config { + pins = "gpio6", "gpio25", "gpio26"; + drive-strength = <8>; + bias-disable = <0>; + }; + }; + + panel_te_pin: panel-te { + mux { + pins = "gpio10"; + function = "mdp_vsync"; + }; + + config { + pins = "gpio10"; + drive-strength = <2>; + bias-disable; + input-enable; + }; + }; + + panel_esd_pin: panel-esd { + mux { + pins = "gpio30"; + function = "gpio"; + }; + config { + pins = "gpio30"; + drive-strength = <2>; + bias-pull-down; + input-enable; + }; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts b/arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts new file mode 100644 index 000000000000..a02f1b99a64f --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts @@ -0,0 +1,19 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * SDM845 OnePlus 6 (enchilada) device tree. + * + * Copyright (c) 2020, The Linux Foundation. All rights reserved. + */ + +#include "sdm845-oneplus-common.dtsi" + +/ { + model = "OnePlus 6"; + compatible = "oneplus,enchilada", "oneplus,oneplus6", "qcom,sdm845"; +}; + +&display_panel { + status = "okay"; + + compatible = "samsung,sofef00"; +}; diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts b/arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts new file mode 100644 index 000000000000..3a05e3b64c03 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts @@ -0,0 +1,23 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * SDM845 OnePlus 6T (fajita) device tree. + * + * Copyright (c) 2020, The Linux Foundation. All rights reserved. + */ + +#include "sdm845-oneplus-common.dtsi" + +/ { + model = "OnePlus 6T"; + compatible = "oneplus,fajita", "oneplus,oneplus6", "qcom,sdm845"; +}; + +&display_panel { + status = "okay"; + + compatible = "samsung,s6e3fc2x01"; +}; + +&rmi4_f12 { + touchscreen-y-mm = <148>; +}; -- 2.29.2 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* Re: [PATCH 3/5] arm64: dts: sdm845: add oneplus 6/t devices 2020-11-12 16:21 ` Caleb Connolly @ 2020-11-16 22:01 ` Pavel Machek 2020-11-16 23:49 ` Caleb Connolly 2020-11-21 4:28 ` Bjorn Andersson 1 sibling, 1 reply; 9+ messages in thread From: Pavel Machek @ 2020-11-16 22:01 UTC (permalink / raw) To: Caleb Connolly Cc: linux-arm-msm, Andy Gross, Bjorn Andersson, Rob Herring, Kees Cook, Anton Vorontsov, Colin Cross, Tony Luck, phone-devel, ~postmarketos/upstreaming, devicetree, linux-kernel Hi! > Add initial support for the OnePlus 6 (enchilada) and 6T (fajita) based > on the sdm845-mtp DT. Support includes: > > * Display panels and Adreno 630 > * Touch screen support with synaptics rmi4 > * All remoteprocs start correctly > * WLAN / Bluetooth > * Volume / power buttons and OnePlus Tri-State switch are functional > The tri-state switch is a 3 state mute slider on the side of the phone * USB > support, currently forced to peripheral as type C detection isn't functional. I have similar switches on my joystick... but I don't believe modelling it as 3 separate keys with "macro" keysym is the right way to go. > + state-top { > + label = "Tri-state key top"; > + linux,code = <KEY_MACRO1>; > + interrupt-parent = <&tlmm>; > + interrupts = <24 IRQ_TYPE_EDGE_FALLING>; > + debounce-interval = <500>; > + linux,can-disable; > + }; > + > + state-middle { > + label = "Tri-state key middle"; > + linux,code = <KEY_MACRO2>; > + interrupt-parent = <&tlmm>; > + interrupts = <52 IRQ_TYPE_EDGE_FALLING>; > + debounce-interval = <500>; > + linux,can-disable; > + }; > + > + state-bottom { > + label = "Tri-state key bottom"; > + linux,code = <KEY_MACRO3>; > + interrupt-parent = <&tlmm>; > + interrupts = <126 IRQ_TYPE_EDGE_FALLING>; > + debounce-interval = <500>; > + linux,can-disable; > + }; Best regards, Pavel -- (english) http://www.livejournal.com/~pavelmachek (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH 3/5] arm64: dts: sdm845: add oneplus 6/t devices 2020-11-16 22:01 ` Pavel Machek @ 2020-11-16 23:49 ` Caleb Connolly 2020-11-21 17:44 ` Pavel Machek 0 siblings, 1 reply; 9+ messages in thread From: Caleb Connolly @ 2020-11-16 23:49 UTC (permalink / raw) To: Pavel Machek Cc: linux-arm-msm, Andy Gross, Bjorn Andersson, Rob Herring, Kees Cook, Anton Vorontsov, Colin Cross, Tony Luck, phone-devel, ~postmarketos/upstreaming, devicetree, linux-kernel On 2020-11-16 22:01, Pavel Machek wrote: > Hi! > >> Add initial support for the OnePlus 6 (enchilada) and 6T (fajita) based >> on the sdm845-mtp DT. Support includes: >> >> * Display panels and Adreno 630 >> * Touch screen support with synaptics rmi4 >> * All remoteprocs start correctly >> * WLAN / Bluetooth >> * Volume / power buttons and OnePlus Tri-State switch are functional >> The tri-state switch is a 3 state mute slider on the side of the phone * USB >> support, currently forced to peripheral as type C detection isn't functional. > I have similar switches on my joystick... but I don't believe modelling it as 3 separate > keys with "macro" keysym is the right way to go. Hi! I agree that this is a bit of a weird way to model the switch, do you have any ideas for a better solution? I'm happy to drop this from the patch for now and come up with a better method down the line. Regards, Caleb >> + state-top { >> + label = "Tri-state key top"; >> + linux,code = <KEY_MACRO1>; >> + interrupt-parent = <&tlmm>; >> + interrupts = <24 IRQ_TYPE_EDGE_FALLING>; >> + debounce-interval = <500>; >> + linux,can-disable; >> + }; >> + >> + state-middle { >> + label = "Tri-state key middle"; >> + linux,code = <KEY_MACRO2>; >> + interrupt-parent = <&tlmm>; >> + interrupts = <52 IRQ_TYPE_EDGE_FALLING>; >> + debounce-interval = <500>; >> + linux,can-disable; >> + }; >> + >> + state-bottom { >> + label = "Tri-state key bottom"; >> + linux,code = <KEY_MACRO3>; >> + interrupt-parent = <&tlmm>; >> + interrupts = <126 IRQ_TYPE_EDGE_FALLING>; >> + debounce-interval = <500>; >> + linux,can-disable; >> + }; > Best regards, > Pavel > -- > (english) http://www.livejournal.com/~pavelmachek > (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH 3/5] arm64: dts: sdm845: add oneplus 6/t devices 2020-11-16 23:49 ` Caleb Connolly @ 2020-11-21 17:44 ` Pavel Machek 0 siblings, 0 replies; 9+ messages in thread From: Pavel Machek @ 2020-11-21 17:44 UTC (permalink / raw) To: Caleb Connolly Cc: linux-arm-msm, Andy Gross, Bjorn Andersson, Rob Herring, Kees Cook, Anton Vorontsov, Colin Cross, Tony Luck, phone-devel, ~postmarketos/upstreaming, devicetree, linux-kernel [-- Attachment #1: Type: text/plain, Size: 1042 bytes --] On Mon 2020-11-16 23:49:32, Caleb Connolly wrote: > On 2020-11-16 22:01, Pavel Machek wrote: > > Hi! > > > >> Add initial support for the OnePlus 6 (enchilada) and 6T (fajita) based > >> on the sdm845-mtp DT. Support includes: > >> > >> * Display panels and Adreno 630 > >> * Touch screen support with synaptics rmi4 > >> * All remoteprocs start correctly > >> * WLAN / Bluetooth > >> * Volume / power buttons and OnePlus Tri-State switch are functional > >> The tri-state switch is a 3 state mute slider on the side of the phone * USB > >> support, currently forced to peripheral as type C detection isn't functional. > > I have similar switches on my joystick... but I don't believe modelling it as 3 separate > > keys with "macro" keysym is the right way to go. > > Hi! I agree that this is a bit of a weird way to model the switch, do > you have any ideas for a better solution? You should ask on the input mailing list, I guess. Best regards, Pavel -- http://www.livejournal.com/~pavelmachek [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 195 bytes --] ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH 3/5] arm64: dts: sdm845: add oneplus 6/t devices 2020-11-12 16:21 ` Caleb Connolly 2020-11-16 22:01 ` Pavel Machek @ 2020-11-21 4:28 ` Bjorn Andersson 1 sibling, 0 replies; 9+ messages in thread From: Bjorn Andersson @ 2020-11-21 4:28 UTC (permalink / raw) To: Caleb Connolly Cc: linux-arm-msm, Andy Gross, Rob Herring, Kees Cook, Anton Vorontsov, Colin Cross, Tony Luck, phone-devel, ~postmarketos/upstreaming, devicetree, linux-kernel On Thu 12 Nov 10:21 CST 2020, Caleb Connolly wrote: [..] > diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi b/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi > new file mode 100644 > index 000000000000..4e6477f1e574 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi > @@ -0,0 +1,822 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * SDM845 OnePlus 6(T) (enchilada / fajita) common device tree source > + * > + * Copyright (c) 2020, The Linux Foundation. All rights reserved. > + */ > + > +/dts-v1/; > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> > +#include <dt-bindings/input/linux-event-codes.h> Please keep these sorted alphabetically. > +#include "sdm845.dtsi" > + > +// Needed for some GPIO (like the volume buttons) This is or is going to be needed for more things, so feel free to skip this comment. > +#include "pm8998.dtsi" > +#include "pmi8998.dtsi" > + > +/ { > + > + aliases { > + hsuart0 = &uart6; > + }; > + > + vph_pwr: vph-pwr-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vph_pwr"; > + regulator-min-microvolt = <3700000>; > + regulator-max-microvolt = <3700000>; > + }; > + > + /* > + * Apparently RPMh does not provide support for PM8998 S4 because it > + * is always-on; model it as a fixed regulator. > + */ > + vreg_s4a_1p8: pm8998-smps4 { > + compatible = "regulator-fixed"; > + regulator-name = "vreg_s4a_1p8"; > + > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + > + regulator-always-on; > + regulator-boot-on; > + > + vin-supply = <&vph_pwr>; > + }; > + > + /* > + * The touchscreen regulator seems to be controlled somehow by a gpio. > + */ > + ts_1p8_supply: ts_1v8_regulator { Please don't use _ in the node name. > + compatible = "regulator-fixed"; > + regulator-name = "ts_1p8_supply"; > + > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + > + gpio = <&tlmm 88 0>; > + enable-active-high; > + regulator-boot-on; > + }; > + > + gpio_tristate_key: gpio-keys { > + compatible = "gpio-keys"; > + label = "Tri-state keys"; What kind of button is this? > + > + pinctrl-names = "default"; > + pinctrl-0 = <&tri_state_key_default>; > + > + state-top { > + label = "Tri-state key top"; > + linux,code = <KEY_MACRO1>; > + interrupt-parent = <&tlmm>; > + interrupts = <24 IRQ_TYPE_EDGE_FALLING>; > + debounce-interval = <500>; > + linux,can-disable; > + }; > + > + state-middle { > + label = "Tri-state key middle"; > + linux,code = <KEY_MACRO2>; > + interrupt-parent = <&tlmm>; > + interrupts = <52 IRQ_TYPE_EDGE_FALLING>; > + debounce-interval = <500>; > + linux,can-disable; > + }; > + > + state-bottom { > + label = "Tri-state key bottom"; > + linux,code = <KEY_MACRO3>; > + interrupt-parent = <&tlmm>; > + interrupts = <126 IRQ_TYPE_EDGE_FALLING>; > + debounce-interval = <500>; > + linux,can-disable; > + }; > + }; [..] > +/* Reserved memory changes */ > +/delete-node/ &rmtfs_mem; > + > +/ { You already have one top-level section higher up, please group this in there as well. > + reserved-memory { [..] > +&mdss { To avoid trouble finding your way around this file in the future I would prefer if you sorted the nodes alphabetically. > + status = "okay"; > +}; > + [..] > +&i2c12 { > + status = "okay"; > + > + touchscreen: synaptics-rmi4-i2c@20 { You don't reference &touchscreen, so please omit this.. Regards, Bjorn ^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2020-11-21 17:44 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <20201007171807.285298-1-caleb@connolly.tech>
2020-10-07 17:20 ` [PATCH 2/5] dt-bindings: panel: add documentation for oneplus6 panel Caleb Connolly
2020-10-07 17:20 ` [PATCH 3/5] arm64: dts: sdm845: add oneplus 6/t devices Caleb Connolly
2020-10-07 17:20 ` [PATCH 4/5] dt-bindings: add vendor bindings for OnePlus Caleb Connolly
[not found] <20201007174736.292968-1-caleb@connolly.tech>
2020-10-07 17:49 ` [PATCH 3/5] arm64: dts: sdm845: add oneplus 6/t devices Caleb Connolly
[not found] <20201112161920.2671430-1-caleb@connolly.tech>
2020-11-12 16:21 ` Caleb Connolly
2020-11-16 22:01 ` Pavel Machek
2020-11-16 23:49 ` Caleb Connolly
2020-11-21 17:44 ` Pavel Machek
2020-11-21 4:28 ` Bjorn Andersson
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).