Re: [PATCH v3 1/4] firmware: arm_scmi: Add Voltage Domain Support

[Cristian Marussi <cristian.marussi@arm.com>]

On Wed, Oct 28, 2020 at 03:29:57PM +0100, Etienne Carriere wrote:
> Hi Cristian,
> 
> Some remaining minor comments see below.
> FYI I've successfully tested this series (the 4 patches).
> 

Hi

Thanks a lot !

Replies inline down below.

[snip]
> > +struct scmi_msg_cmd_config_set {
> > +       __le32 domain_id;
> > +       __le32 config;
> > +};
> > +
> > +struct scmi_msg_cmd_level_set {
> > +       __le32 domain_id;
> > +       __le32 flags;
> > +       __le32 voltage_level;
> > +};
> > +
> > +struct voltage_info {
> > +       u32 version;
> > +       u16 num_domains;
> 
> Could be an unsigned int.
> 

I tend to use fixed size types matching the protocols messages sizing on
the internal while exposing non-fixed size types in scmi_protocol.h like
in scmi_voltage_info, but these indeed are values exposed directly to
the user afterwards. Any other reason to prefer non-fixed size here ?

> > +       struct scmi_voltage_info **domains;
> > +};
> > +
> > +static int scmi_protocol_attributes_get(const struct scmi_handle *handle,
> > +                                       struct voltage_info *vinfo)
> > +{
> > +       int ret;
> > +       struct scmi_xfer *t;
> > +       struct scmi_msg_resp_protocol_attributes *resp;
> > +
> > +       ret = scmi_xfer_get_init(handle, PROTOCOL_ATTRIBUTES,
> > +                                SCMI_PROTOCOL_VOLTAGE, 0, sizeof(*resp), &t);
> > +       if (ret)
> > +               return ret;
> > +
> > +       resp = t->rx.buf;
> > +       ret = scmi_do_xfer(handle, t);
> > +       if (!ret)
> > +               vinfo->num_domains =
> > +                       NUM_VOLTAGE_DOMAINS(le32_to_cpu(resp->attr));
> > +
> > +       scmi_xfer_put(handle, t);
> > +       return ret;
> > +}
> > +
> > +static inline int scmi_init_voltage_levels(struct device *dev,
> 
> Should remove this inline attribute.
> 

Ah right, I removed one and left this. I'll do.

> > +                                          struct scmi_voltage_info *v,
> > +                                          u32 flags, u32 num_returned,
> > +                                          u32 num_remaining)

[snip]

> > +DEFINE_SCMI_PROTOCOL_REGISTER_UNREGISTER(SCMI_PROTOCOL_VOLTAGE, voltage)
> > diff --git a/include/linux/scmi_protocol.h b/include/linux/scmi_protocol.h
> > index 9cd312a1ff92..181fdebc2793 100644
> > --- a/include/linux/scmi_protocol.h
> > +++ b/include/linux/scmi_protocol.h
> > @@ -209,6 +209,64 @@ struct scmi_reset_ops {
> >         int (*deassert)(const struct scmi_handle *handle, u32 domain);
> >  };
> >
> > +/**
> > + * struct scmi_voltage_info - describe one available SCMI Voltage Domain
> > + *
> > + * @id: the domain ID as advertised by the platform
> > + * @segmented: defines the layout of the entries of array @levels_uv.
> > + *            - when True the entries are to be interpreted as triplets,
> > + *              each defining a segment representing a range of equally
> > + *              space voltages: <lowest_volts>, <highest_volt>, <step_uV>
> > + *            - when False the entries simply represent a single discrete
> > + *              supported voltage level
> > + * @negative_volts_allowed: True if any of the entries of @levels_uv represent
> > + *                         a negative voltage.
> > + * @attributes: represents Voltage Domain advertised attributes
> > + * @name: name assigned to the Voltage Domain by platform
> > + * @num_levels: number of total entries in @levels_uv.
> > + * @levels_uv: array of entries describing the available voltage levels for
> > + *            this domain.
> > + */
> > +struct scmi_voltage_info {
> > +       unsigned int id;
> > +       bool segmented;
> > +#define SCMI_VOLTAGE_SEGMENT_LOW       0
> > +#define SCMI_VOLTAGE_SEGMENT_HIGH      1
> > +#define SCMI_VOLTAGE_SEGMENT_STEP      2
> 
> Maybe move these macros before 'int *level_us;' as these are indices
> in that array.
> 

Right, I'll do.

Thanks

Cristian

> > +       bool negative_volts_allowed;
> > +       unsigned int attributes;
> > +       char name[SCMI_MAX_STR_SIZE];
> > +       unsigned int num_levels;
> > +       int *levels_uv;
> > +};
> > +
> > +/**
> > + * struct scmi_voltage_ops - represents the various operations provided
> > + * by SCMI Voltage Protocol
> > + *
> > + * @num_domains_get: get the count of voltage domains provided by SCMI
> > + * @info_get: get the information of the specified domain
> > + * @config_set: set the config for the specified domain
> > + * @config_get: get the config of the specified domain
> > + * @level_set: set the voltage level for the specified domain
> > + * @level_get: get the voltage level of the specified domain
> > + */
> > +struct scmi_voltage_ops {
> > +       int (*num_domains_get)(const struct scmi_handle *handle);
> > +       const struct scmi_voltage_info __must_check *(*info_get)
> > +               (const struct scmi_handle *handle, u32 domain_id);
> > +       int (*config_set)(const struct scmi_handle *handle, u32 domain_id,
> > +                         u32 config);
> > +#define        SCMI_VOLTAGE_ARCH_STATE_OFF             0x0
> > +#define        SCMI_VOLTAGE_ARCH_STATE_ON              0x7
> > +       int (*config_get)(const struct scmi_handle *handle, u32 domain_id,
> > +                         u32 *config);
> > +       int (*level_set)(const struct scmi_handle *handle, u32 domain_id,
> > +                        u32 flags, s32 volt_uV);
> > +       int (*level_get)(const struct scmi_handle *handle, u32 domain_id,
> > +                        s32 *volt_uV);
> > +};
> > +
> >  /**
> >   * struct scmi_notify_ops  - represents notifications' operations provided by
> >   * SCMI core
> > @@ -262,6 +320,7 @@ struct scmi_notify_ops {
> >   * @clk_ops: pointer to set of clock protocol operations
> >   * @sensor_ops: pointer to set of sensor protocol operations
> >   * @reset_ops: pointer to set of reset protocol operations
> > + * @voltage_ops: pointer to set of voltage protocol operations
> >   * @notify_ops: pointer to set of notifications related operations
> >   * @perf_priv: pointer to private data structure specific to performance
> >   *     protocol(for internal use only)
> > @@ -273,6 +332,8 @@ struct scmi_notify_ops {
> >   *     protocol(for internal use only)
> >   * @reset_priv: pointer to private data structure specific to reset
> >   *     protocol(for internal use only)
> > + * @voltage_priv: pointer to private data structure specific to voltage
> > + *     protocol(for internal use only)
> >   * @notify_priv: pointer to private data structure specific to notifications
> >   *     (for internal use only)
> >   */
> > @@ -284,6 +345,7 @@ struct scmi_handle {
> >         const struct scmi_power_ops *power_ops;
> >         const struct scmi_sensor_ops *sensor_ops;
> >         const struct scmi_reset_ops *reset_ops;
> > +       const struct scmi_voltage_ops *voltage_ops;
> >         const struct scmi_notify_ops *notify_ops;
> >         /* for protocol internal use */
> >         void *perf_priv;
> > @@ -291,6 +353,7 @@ struct scmi_handle {
> >         void *power_priv;
> >         void *sensor_priv;
> >         void *reset_priv;
> > +       void *voltage_priv;
> >         void *notify_priv;
> >         void *system_priv;
> >  };
> > @@ -303,6 +366,7 @@ enum scmi_std_protocol {
> >         SCMI_PROTOCOL_CLOCK = 0x14,
> >         SCMI_PROTOCOL_SENSOR = 0x15,
> >         SCMI_PROTOCOL_RESET = 0x16,
> > +       SCMI_PROTOCOL_VOLTAGE = 0x17,
> >  };
> >
> >  enum scmi_system_events {
> > --
> > 2.17.1
> >