From: Sekhar Nori <nsekhar@ti.com>
To: Nishanth Menon <nm@ti.com>, Tero Kristo <t-kristo@ti.com>
Cc: Faiz Abbas <faiz_abbas@ti.com>, Rob Herring <robh+dt@kernel.org>,
Linux ARM Mailing List <linux-arm-kernel@lists.infradead.org>,
Device Tree Mailing List <devicetree@vger.kernel.org>
Subject: [PATCH v2 2/2] arm64: dts: ti: k3-j721e-common-proc-board: Add support SD card UHS modes
Date: Sat, 28 Nov 2020 01:40:24 +0530 [thread overview]
Message-ID: <20201127201024.64836-3-nsekhar@ti.com> (raw)
In-Reply-To: <20201127201024.64836-1-nsekhar@ti.com>
From: Faiz Abbas <faiz_abbas@ti.com>
Add support for UHS modes for the SD card connected at sdhci1. This
involves adding regulators for voltage switching and power cycling the
SD card and removing the no-1-8-v property.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
---
.../dts/ti/k3-j721e-common-proc-board.dts | 35 ++++++++++++++++++-
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 2 --
2 files changed, 34 insertions(+), 3 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
index 5754892f8501..529b072e1eaf 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
@@ -67,6 +67,31 @@
regulator-boot-on;
};
+ vdd_mmc1: fixedregulator-sd {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_mmc1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ enable-active-high;
+ vin-supply = <&vsys_3v3>;
+ gpio = <&exp2 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ vdd_sd_dv_alt: gpio-regulator-TLV71033 {
+ compatible = "regulator-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vdd_sd_dv_alt_pins_default>;
+ regulator-name = "tlv71033";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ vin-supply = <&vsys_5v0>;
+ gpios = <&main_gpio0 117 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x0>,
+ <3300000 0x1>;
+ };
+
sound0: sound@0 {
compatible = "ti,j721e-cpb-audio";
model = "j721e-cpb";
@@ -106,7 +131,13 @@
>;
};
- main_usbss0_pins_default: main-usbss0-pins-default {
+ vdd_sd_dv_alt_pins_default: vdd_sd_dv_alt_pins_default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x1d8, PIN_INPUT, 7) /* (W4) SPI1_CS1.GPIO0_117 */
+ >;
+ };
+
+ main_usbss0_pins_default: main_usbss0_pins_default {
pinctrl-single,pins = <
J721E_IOPAD(0x290, PIN_OUTPUT, 0) /* (U6) USB0_DRVVBUS */
J721E_IOPAD(0x210, PIN_INPUT, 7) /* (W3) MCAN1_RX.GPIO1_3 */
@@ -295,6 +326,8 @@
&main_sdhci1 {
/* SD/MMC */
+ vmmc-supply = <&vdd_mmc1>;
+ vqmmc-supply = <&vdd_sd_dv_alt>;
pinctrl-names = "default";
pinctrl-0 = <&main_mmc1_pins_default>;
ti,driver-strength-ohm = <50>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
index d87748cb6896..2056a41f9378 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
@@ -1107,7 +1107,6 @@
ti,trm-icp = <0x8>;
ti,clkbuf-sel = <0x7>;
dma-coherent;
- no-1-8-v;
};
main_sdhci2: sdhci@4f98000 {
@@ -1128,7 +1127,6 @@
ti,trm-icp = <0x8>;
ti,clkbuf-sel = <0x7>;
dma-coherent;
- no-1-8-v;
};
usbss0: cdns-usb@4104000 {
--
2.17.1
next prev parent reply other threads:[~2020-11-27 20:28 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-11-27 20:10 [PATCH v2 0/2] arm64: dts: ti: k3-j721e: MMC/SD higher speed modes support Sekhar Nori
2020-11-27 20:10 ` [PATCH v2 1/2] arm64: dts: ti: k3-j721e-main: Add output tap delay values Sekhar Nori
2020-11-27 20:10 ` Sekhar Nori [this message]
2020-11-28 16:41 ` [PATCH v2 2/2] arm64: dts: ti: k3-j721e-common-proc-board: Add support SD card UHS modes Nishanth Menon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201127201024.64836-3-nsekhar@ti.com \
--to=nsekhar@ti.com \
--cc=devicetree@vger.kernel.org \
--cc=faiz_abbas@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=nm@ti.com \
--cc=robh+dt@kernel.org \
--cc=t-kristo@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox