[PATCH v4 0/3] mainline Plymovent M2M and BAS board

[PATCH v4 0/3] mainline Plymovent M2M and BAS board

[Oleksij Rempel]

changes v5:
- rebase against latest shawngup/for-next
- add patch to fix checkpatch warning on PLYM2M dts

changes v4:
- add PLYBAS board
- PLYM2M: add touchscreen node
- PLYM2M: add rename led nodes to led-x

changes v3:
- use old style copyright text

changes v2:
- fsl.yaml: reorder ply,plym2m
- imx6dl-plym2m.dts: use hyphen instead of underscore in phy-clock

Oleksij Rempel (6):
  dt-bindings: display: simple: Add EDT ETM0700G0BDH6 display
  dt-bindings: vendor-prefixes: Add an entry for Plymovent
  dt-bindings: arm: fsl: add Plymovent M2M board
  ARM: dts: add Plymovent M2M board
  dt-bindings: arm: fsl: add Plymovent BAS board
  ARM: dts: add Plymovent BAS board

 .../devicetree/bindings/arm/fsl.yaml          |   2 +
 .../bindings/display/panel/panel-simple.yaml  |   2 +
 .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
 arch/arm/boot/dts/Makefile                    |   2 +
 arch/arm/boot/dts/imx6dl-plybas.dts           | 394 ++++++++++++++++
 arch/arm/boot/dts/imx6dl-plym2m.dts           | 446 ++++++++++++++++++
 6 files changed, 848 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6dl-plybas.dts
 create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts

-- 
2.29.2

[PATCH v5 1/6] dt-bindings: display: simple: Add EDT ETM0700G0BDH6 display

[Oleksij Rempel]

This display is already supported by the panel-simple driver, so add it
to the bindings documentation.

This patch is needed to fix checkpatch warnings for the PLYM2M dts.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 .../devicetree/bindings/display/panel/panel-simple.yaml         | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
index edb53ab0d9eb..a011d9e44af3 100644
--- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
+++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
@@ -117,6 +117,8 @@ properties:
       - edt,etm0700g0dh6
         # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
         # Same as ETM0700G0DH6 but with inverted pixel clock.
+      - edt,etm0700g0bdh6
+        # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
       - edt,etm070080bdh6
         # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
         # Same display as the ETM0700G0BDH6, but with changed hardware for the
-- 
2.29.2

Re: [PATCH v5 1/6] dt-bindings: display: simple: Add EDT ETM0700G0BDH6 display

[Sam Ravnborg]

Hi Oleksij

On Tue, Dec 01, 2020 at 10:27:37AM +0100, Oleksij Rempel wrote:
> This display is already supported by the panel-simple driver, so add it
> to the bindings documentation.
> 
> This patch is needed to fix checkpatch warnings for the PLYM2M dts.
> 
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>  .../devicetree/bindings/display/panel/panel-simple.yaml         | 2 ++
>  1 file changed, 2 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
> index edb53ab0d9eb..a011d9e44af3 100644
> --- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
> +++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
> @@ -117,6 +117,8 @@ properties:
>        - edt,etm0700g0dh6
>          # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
>          # Same as ETM0700G0DH6 but with inverted pixel clock.
> +      - edt,etm0700g0bdh6
> +        # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
>        - edt,etm070080bdh6
>          # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
>          # Same display as the ETM0700G0BDH6, but with changed hardware for the

The panels should be listed in alphabetic order which is not the case
here. Could you fix the alphabetic order for the edt panels and then
insert the new panel in the right spot?

	Sam

Re: [PATCH v5 1/6] dt-bindings: display: simple: Add EDT ETM0700G0BDH6 display

[Oleksij Rempel]

On Tue, Dec 01, 2020 at 12:56:12PM +0100, Sam Ravnborg wrote:
> Hi Oleksij
> 
> On Tue, Dec 01, 2020 at 10:27:37AM +0100, Oleksij Rempel wrote:
> > This display is already supported by the panel-simple driver, so add it
> > to the bindings documentation.
> > 
> > This patch is needed to fix checkpatch warnings for the PLYM2M dts.
> > 
> > Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> > ---
> >  .../devicetree/bindings/display/panel/panel-simple.yaml         | 2 ++
> >  1 file changed, 2 insertions(+)
> > 
> > diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
> > index edb53ab0d9eb..a011d9e44af3 100644
> > --- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
> > +++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
> > @@ -117,6 +117,8 @@ properties:
> >        - edt,etm0700g0dh6
> >          # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
> >          # Same as ETM0700G0DH6 but with inverted pixel clock.
> > +      - edt,etm0700g0bdh6
> > +        # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
> >        - edt,etm070080bdh6
> >          # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
> >          # Same display as the ETM0700G0BDH6, but with changed hardware for the
> 
> The panels should be listed in alphabetic order which is not the case
> here. Could you fix the alphabetic order for the edt panels and then
> insert the new panel in the right spot?

ack, will be done

-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

[PATCH v5 2/6] dt-bindings: vendor-prefixes: Add an entry for Plymovent

[Oleksij Rempel]

Add "ply" entry for Plymovent Group BV: https://www.plymovent.com/

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 6a9be2bbbcb6..8332d50301ea 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -840,6 +840,8 @@ patternProperties:
     description: PLDA
   "^plx,.*":
     description: Broadcom Corporation (formerly PLX Technology)
+  "^ply,.*":
+    description: Plymovent Group BV
   "^pni,.*":
     description: PNI Sensor Corporation
   "^pocketbook,.*":
-- 
2.29.2

[PATCH v5 3/6] dt-bindings: arm: fsl: add Plymovent M2M board

[Oleksij Rempel]

Add Plymovent Group BV M2M iMX6dl based board

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 4772f64c4463..36c5a0c5ace2 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -364,6 +364,7 @@ properties:
               - fsl,imx6dl-sabresd        # i.MX6 DualLite SABRE Smart Device Board
               - karo,imx6dl-tx6dl         # Ka-Ro electronics TX6U Modules
               - kontron,imx6dl-samx6i     # Kontron i.MX6 Solo SMARC Module
+              - ply,plym2m                # Plymovent M2M board
               - poslab,imx6dl-savageboard # Poslab SavageBoard Dual
               - prt,prtrvt                # Protonic RVT board
               - prt,prtvt7                # Protonic VT7 board
-- 
2.29.2

[PATCH v5 4/6] ARM: dts: add Plymovent M2M board

[Oleksij Rempel]

Plymovent M2M is a control interface produced for the Plymovent filter
systems.

Co-Developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/Makefile          |   1 +
 arch/arm/boot/dts/imx6dl-plym2m.dts | 446 ++++++++++++++++++++++++++++
 2 files changed, 447 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 3ab9d58428cf..31249fc5f85c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -461,6 +461,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6dl-pico-hobbit.dtb \
 	imx6dl-pico-nymph.dtb \
 	imx6dl-pico-pi.dtb \
+	imx6dl-plym2m.dtb \
 	imx6dl-prtrvt.dtb \
 	imx6dl-prtvt7.dtb \
 	imx6dl-rex-basic.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
new file mode 100644
index 000000000000..4d0d3d3386af
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
@@ -0,0 +1,446 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "imx6dl.dtsi"
+
+/ {
+	model = "Plymovent M2M board";
+	compatible = "ply,plym2m", "fsl,imx6dl";
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 5000000 0>;
+		brightness-levels = <0 1000>;
+		num-interpolated-steps = <20>;
+		default-brightness-level = <19>;
+		power-supply = <&reg_12v0>;
+	};
+
+	display {
+		compatible = "fsl,imx-parallel-display";
+		pinctrl-0 = <&pinctrl_ipu1_disp>;
+		pinctrl-names = "default";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			display_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-0 {
+			label = "debug0";
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	panel {
+		compatible = "edt,etm0700g0bdh6";
+		backlight = <&backlight>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
+	clk50m_phy: phy-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_12v0: regulator-12v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "12v0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	xceiver-supply = <&reg_5v0>;
+	status = "okay";
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&ecspi2 {
+	cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	status = "okay";
+
+	touchscreen@0 {
+		compatible = "ti,tsc2046";
+		reg = <0>;
+		pinctrl-0 = <&pinctrl_tsc2046>;
+		pinctrl-names ="default";
+		spi-max-frequency = <100000>;
+		interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
+		pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
+
+		touchscreen-size-x = <800>;
+		touchscreen-size-y = <480>;
+		touchscreen-inverted-x;
+		touchscreen-inverted-y;
+		touchscreen-max-pressure = <4095>;
+
+		ti,vref-delay-usecs = /bits/ 16 <100>;
+		ti,x-plate-ohms = /bits/ 16 <800>;
+		ti,y-plate-ohms = /bits/ 16 <300>;
+
+		wakeup-source;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rmii";
+	clocks = <&clks IMX6QDL_CLK_ENET>,
+		 <&clks IMX6QDL_CLK_ENET>,
+		 <&clk50m_phy>;
+	clock-names = "ipg", "ahb", "ptp";
+	phy-handle = <&rgmii_phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Microchip KSZ8081RNA PHY */
+		rgmii_phy: ethernet-phy@0 {
+			reg = <0>;
+			interrupts-extended = <&gpio5 23 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"CAN1_TERM", "SD1_CD", "", "", "", "", "", "",
+		"DEBUG_0", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "ECSPI2_SS0", "", "", "", "TSC_BUSY", "";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "ECSPI1_SS1", "TSC_PENIRQ", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "CAN1_SR", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "ETH_RESET", "ETH_INTRP",
+		"", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	/* additional i2c devices are added automatically by the boot loader */
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	temperature-sensor@70 {
+		compatible = "ti,tmp103";
+		reg = <0x70>;
+	};
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&display_in>;
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usbphynop1 {
+	status = "disabled";
+};
+
+&usbphynop2 {
+	status = "disabled";
+};
+
+&usbotg {
+	phy_type = "utmi";
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	disable-wp;
+	cap-sd-highspeed;
+	no-mmc;
+	no-sdio;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX		0x1b000
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX		0x3008
+			/* CAN1_SR */
+			MX6QDL_PAD_KEY_COL3__GPIO4_IO12			0x13008
+			/* CAN1_TERM */
+			MX6QDL_PAD_GPIO_0__GPIO1_IO00			0x1b088
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO			0x1b000
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI			0x3008
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK			0x3008
+			/* CS */
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19			0x3008
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_OE__ECSPI2_MISO			0x10000
+			MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK			0x3008
+			MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI			0x3008
+			/* CS */
+			MX6QDL_PAD_EIM_RW__GPIO2_IO26			0x3008
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			/* MX6QDL_ENET_PINGRP4 */
+			MX6QDL_PAD_ENET_MDC__ENET_MDC			0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO			0x1b0b0
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER		0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN		0x1b0b0
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN		0x1b0b0
+
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK		0x1b0b0
+			/* Phy reset */
+			MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22		0x1b0b0
+			/* nINTRP */
+			MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23		0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA			0x4001f8b1
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL			0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL			0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA			0x4001b8b1
+		>;
+	};
+
+	pinctrl_ipu1_disp: ipudisp1grp {
+		fsl,pins = <
+			/* DSE 0x30 => 25 Ohm, 0x20 => 37 Ohm, 0x10 => 75 Ohm */
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x30
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15		0x30
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x30
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x30
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x30
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x30
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x30
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x30
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x30
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x30
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x30
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x30
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x30
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x30
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x30
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x30
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x30
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x30
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x30
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x30
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x30
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x30
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_8__GPIO1_IO08			0x1b0b0
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__PWM1_OUT			0x8
+		>;
+	};
+
+	pinctrl_tsc2046: tsc2046grp {
+		fsl,pins = <
+			/* TSC_PENIRQ */
+			MX6QDL_PAD_EIM_D20__GPIO3_IO20			0x1b0b1
+			/* TSC_BUSY */
+			MX6QDL_PAD_EIM_EB2__GPIO2_IO30			0x1b0b0
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA		0x1b0b1
+			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD			0x170f9
+			MX6QDL_PAD_SD1_CLK__SD1_CLK			0x100f9
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0			0x170f9
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1			0x170f9
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2			0x170f9
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3			0x170f9
+			MX6QDL_PAD_GPIO_1__GPIO1_IO01			0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD			0x17099
+			MX6QDL_PAD_SD3_CLK__SD3_CLK			0x10099
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0			0x17099
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1			0x17099
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2			0x17099
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3			0x17099
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4			0x17099
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5			0x17099
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6			0x17099
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7			0x17099
+			MX6QDL_PAD_SD3_RST__SD3_RESET			0x1b0b1
+		>;
+	};
+};
-- 
2.29.2

[PATCH v5 5/6] dt-bindings: arm: fsl: add Plymovent BAS board

[Oleksij Rempel]

Add Plymovent Group BV BAS iMX6dl based board

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 36c5a0c5ace2..490cbc75b18a 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -364,6 +364,7 @@ properties:
               - fsl,imx6dl-sabresd        # i.MX6 DualLite SABRE Smart Device Board
               - karo,imx6dl-tx6dl         # Ka-Ro electronics TX6U Modules
               - kontron,imx6dl-samx6i     # Kontron i.MX6 Solo SMARC Module
+              - ply,plybas                # Plymovent BAS board
               - ply,plym2m                # Plymovent M2M board
               - poslab,imx6dl-savageboard # Poslab SavageBoard Dual
               - prt,prtrvt                # Protonic RVT board
-- 
2.29.2

[PATCH v5 6/6] ARM: dts: add Plymovent BAS board

[Oleksij Rempel]

Plymovent BAS is a base system controller produced for the Plymovent filter
systems.

Co-Developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/Makefile          |   1 +
 arch/arm/boot/dts/imx6dl-plybas.dts | 394 ++++++++++++++++++++++++++++
 2 files changed, 395 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6dl-plybas.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 31249fc5f85c..ee725aebc3a8 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -461,6 +461,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6dl-pico-hobbit.dtb \
 	imx6dl-pico-nymph.dtb \
 	imx6dl-pico-pi.dtb \
+	imx6dl-plybas.dtb \
 	imx6dl-plym2m.dtb \
 	imx6dl-prtrvt.dtb \
 	imx6dl-prtvt7.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-plybas.dts b/arch/arm/boot/dts/imx6dl-plybas.dts
new file mode 100644
index 000000000000..333c306aa946
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-plybas.dts
@@ -0,0 +1,394 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "imx6dl.dtsi"
+
+/ {
+	model = "Plymovent BAS board";
+	compatible = "ply,plybas", "fsl,imx6dl";
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		autorepeat;
+
+		button@20 {
+			label = "START";
+			linux,code = <31>;
+			gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
+		};
+
+		button@21 {
+			label = "CLEAN";
+			linux,code = <46>;
+			gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-0 {
+			label = "debug0";
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-1 {
+			label = "debug1";
+			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-2 {
+			label = "light_tower1";
+			gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-3 {
+			label = "light_tower2";
+			gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-4 {
+			label = "light_tower3";
+			gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-5 {
+			label = "light_tower4";
+			gpios = <&gpio4 25 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	clk50m_phy: phy-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+	};
+
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	xceiver-supply = <&reg_5v0>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can2>;
+	xceiver-supply = <&reg_5v0>;
+	status = "okay";
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rmii";
+	clocks = <&clks IMX6QDL_CLK_ENET>,
+		 <&clks IMX6QDL_CLK_ENET>,
+		 <&clk50m_phy>;
+	clock-names = "ipg", "ahb", "ptp";
+	phy-handle = <&rgmii_phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Microchip KSZ8081RNA PHY */
+		rgmii_phy: ethernet-phy@0 {
+			reg = <0>;
+			interrupts-extended = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"", "SD1_CD", "", "", "", "", "", "",
+		"DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "ECSPI1_SS1", "", "USB_EXT_PWR", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "CAN1_SR", "CAN2_SR", "", "",
+		"LED_DI0_DEBUG_0", "LED_DI0_DEBUG_1", "IMX6_IN12", "IMX6_HMI",
+			"IMX6_IN11", "IMX6_BUZZER", "IMX6_LED1", "IMX6_LED2",
+		"IMX6_LED3", "IMX6_LED4", "ETH_RESET", "IMX6_ANA_OUT_SD",
+			"IMX6_ANA_OUT_ERR", "IMX6_ANA_OUT", "ETH_INTRP", "";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"", "", "", "", "", "IMX6_RELAY1", "IMX6_RELAY2", "",
+		"IMX6_IN1", "IMX6_IN2", "IMX6_IN3", "IMX6_IN4", "IMX6_IN5",
+			"IMX6_IN6", "IMX6_IN7", "IMX6_IN8",
+		"IMX6_IN9", "IMX6_IN10", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	/* additional i2c devices are added automatically by the boot loader */
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	temperature-sensor@70 {
+		compatible = "ti,tmp103";
+		reg = <0x70>;
+	};
+
+	rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	fsl,uart-has-rtscts;
+	linux,rs485-enabled-at-boot-time;
+	rs485-rts-delay = <0 20>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	phy_type = "utmi";
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&usbphynop1 {
+	status = "disabled";
+};
+
+&usbphynop2 {
+	status = "disabled";
+};
+
+&iomuxc {
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX		0x1b000
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX		0x3008
+			/* CAN1_SR */
+			MX6QDL_PAD_KEY_COL3__GPIO4_IO12			0x13008
+		>;
+	};
+
+	pinctrl_can2: can2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX		0x1b000
+			MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX		0x3008
+			/* CAN2_SR */
+			MX6QDL_PAD_KEY_ROW3__GPIO4_IO13			0x13008
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO			0x1b000
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI			0x3008
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK			0x3008
+			/* CS */
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19			0x3008
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			/* MX6QDL_ENET_PINGRP4 */
+			MX6QDL_PAD_ENET_MDC__ENET_MDC			0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO			0x1b0b0
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER		0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN		0x1b0b0
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN		0x1b0b0
+
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK		0x1b0b0
+			/* Phy reset */
+			MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26		0x1b0b0
+			/* nINTRP */
+			MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30		0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA			0x4001f8b1
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL			0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL			0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA			0x4001b8b1
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			/* DEBUG_0 */
+			MX6QDL_PAD_GPIO_8__GPIO1_IO08			0x1b0b0
+			/* DEBUG_1 */
+			MX6QDL_PAD_GPIO_9__GPIO1_IO09			0x1b0b0
+
+			/* LED1 (lighttower) */
+			MX6QDL_PAD_DISP0_DAT1__GPIO4_IO22		0x13070
+			/* LED2 (lighttower) */
+			MX6QDL_PAD_DISP0_DAT2__GPIO4_IO23		0x13070
+			/* LED3 (lighttower) */
+			MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24		0x13070
+			/* LED4 (lighttower) */
+			MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25		0x13070
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT8__PWM1_OUT			0x1b0b0
+		>;
+	};
+
+	/* YaCO AUX Uart */
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA		0x1b0b1
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__UART2_TX_DATA		0x1b0b1
+			MX6QDL_PAD_EIM_D27__UART2_RX_DATA		0x1b0b1
+			MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B		0x130b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA		0x1b0b1
+			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__USB_OTG_OC			0x1b0b0
+			/* power enable, high active */
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22			0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD			0x170f9
+			MX6QDL_PAD_SD1_CLK__SD1_CLK			0x100f9
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0			0x170f9
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1			0x170f9
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2			0x170f9
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3			0x170f9
+			MX6QDL_PAD_GPIO_1__GPIO1_IO01			0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD			0x17099
+			MX6QDL_PAD_SD3_CLK__SD3_CLK			0x10099
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0			0x17099
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1			0x17099
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2			0x17099
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3			0x17099
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4			0x17099
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5			0x17099
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6			0x17099
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7			0x17099
+			MX6QDL_PAD_SD3_RST__SD3_RESET			0x1b0b1
+		>;
+	};
+};
-- 
2.29.2