From: Bert Vermeulen <bert@biot.com>
To: Thomas Bogendoerfer <tsbogend@alpha.franken.de>,
Rob Herring <robh+dt@kernel.org>,
Sander Vanheule <sander@svanheule.net>,
linux-mips@vger.kernel.org, linux-kernel@vger.kernel.org,
devicetree@vger.kernel.org
Cc: Bert Vermeulen <bert@biot.com>
Subject: [PATCH v3 4/4] dts: Add support for Cisco SG220-26 switch
Date: Wed, 30 Dec 2020 22:22:05 +0100 [thread overview]
Message-ID: <20201230212205.2605383-4-bert@biot.com> (raw)
In-Reply-To: <20201230212205.2605383-1-bert@biot.com>
Signed-off-by: Bert Vermeulen <bert@biot.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
---
arch/mips/Kconfig | 10 +++
arch/mips/boot/dts/realtek/Makefile | 2 +
arch/mips/boot/dts/realtek/cisco_sg220-26.dts | 81 +++++++++++++++++++
3 files changed, 93 insertions(+)
create mode 100644 arch/mips/boot/dts/realtek/Makefile
create mode 100644 arch/mips/boot/dts/realtek/cisco_sg220-26.dts
diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
index 0986d0c4405f..a398416842ca 100644
--- a/arch/mips/Kconfig
+++ b/arch/mips/Kconfig
@@ -1055,6 +1055,16 @@ config NLM_XLP_BOARD
endchoice
+if MACH_REALTEK_RTL
+choice
+ prompt "Realtek RTL838x/RTL839x-based switch"
+ optional
+
+ config DT_CISCO_SG220_26
+ bool "Cisco SG220-26"
+endchoice
+endif
+
source "arch/mips/alchemy/Kconfig"
source "arch/mips/ath25/Kconfig"
source "arch/mips/ath79/Kconfig"
diff --git a/arch/mips/boot/dts/realtek/Makefile b/arch/mips/boot/dts/realtek/Makefile
new file mode 100644
index 000000000000..f0a3e5816767
--- /dev/null
+++ b/arch/mips/boot/dts/realtek/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_DT_CISCO_SG220_26) += cisco_sg220-26.dtb
diff --git a/arch/mips/boot/dts/realtek/cisco_sg220-26.dts b/arch/mips/boot/dts/realtek/cisco_sg220-26.dts
new file mode 100644
index 000000000000..5d8ba3df95aa
--- /dev/null
+++ b/arch/mips/boot/dts/realtek/cisco_sg220-26.dts
@@ -0,0 +1,81 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR BSD-2-Clause
+
+/dts-v1/;
+
+#include "rtl83xx.dtsi"
+#include "rtl838x.dtsi"
+
+/ {
+ model = "Cisco SG220-26";
+ compatible = "cisco,sg220-26", "realtek,rtl8382-soc";
+
+ chosen {
+ stdout-path = "serial0:9600n8";
+ bootargs = "earlycon console=ttyS0,9600";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x8000000>;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&spi {
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <10000000>;
+ reg = <0>;
+ m25p,fast-read;
+ broken-flash-reset;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ loader: partition@0 {
+ label = "boot";
+ reg = <0x0 0x80000>;
+ read-only;
+ };
+
+ bdinfo: partition@80000 {
+ label = "bdinfo";
+ reg = <0x80000 0x10000>;
+ read-only;
+ };
+
+ sysinfo: partition@90000 {
+ label = "sysinfo";
+ reg = <0x90000 0x10000>;
+ read-only;
+ };
+
+ jffs2_cfg: partition@a0000 {
+ label = "jffs2 cfg";
+ reg = <0xa0000 0x400000>;
+ };
+
+ jffs2_log: partition@4a0000 {
+ label = "jffs2 log";
+ reg = <0x4a0000 0x100000>;
+ };
+
+ runtime: partition@5a0000 {
+ label = "runtime";
+ reg = <0x5a0000 0xd30000>;
+ };
+
+ runtime2: partition@12d0000 {
+ label = "runtime2";
+ reg = <0x12d0000 0xd30000>;
+ };
+ };
+ };
+};
--
2.25.1
next prev parent reply other threads:[~2020-12-30 21:23 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-12-30 21:22 [PATCH v3 1/4] Add support for Realtek RTL838x/RTL839x switch SoCs Bert Vermeulen
2020-12-30 21:22 ` [PATCH v3 2/4] MIPS: Add Realtek RTL838x/RTL839x support as generic MIPS system Bert Vermeulen
2021-01-05 10:20 ` Thomas Bogendoerfer
2020-12-30 21:22 ` [PATCH v3 3/4] dt-bindings: Add Cisco prefix to vendor list Bert Vermeulen
2021-01-11 22:01 ` Rob Herring
2020-12-30 21:22 ` Bert Vermeulen [this message]
2020-12-30 21:26 ` [PATCH v3 1/4] Add support for Realtek RTL838x/RTL839x switch SoCs Bert Vermeulen
2021-01-11 21:59 ` Rob Herring
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201230212205.2605383-4-bert@biot.com \
--to=bert@biot.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mips@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=sander@svanheule.net \
--cc=tsbogend@alpha.franken.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).