[PATCH v12 03/17] dt-bindings: fix sifive plic compatible string

[PATCH v12 03/17] dt-bindings: fix sifive plic compatible string

[Damien Le Moal]

Allow the compatible string of a Sifive plic node to specify only
"sifive,plic-1.0.0" without an additional required string specifying
the SoC implementing the IP block. With this change, the plic node of
RISC-V SoCs using a generic implementation of the plic without any SoC
specific tweak can be correctly defined.

Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
---
 .../interrupt-controller/sifive,plic-1.0.0.yaml        | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/interrupt-controller/sifive,plic-1.0.0.yaml b/Documentation/devicetree/bindings/interrupt-controller/sifive,plic-1.0.0.yaml
index b9a61c9f7530..167418a0021a 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/sifive,plic-1.0.0.yaml
+++ b/Documentation/devicetree/bindings/interrupt-controller/sifive,plic-1.0.0.yaml
@@ -41,9 +41,13 @@ maintainers:
 
 properties:
   compatible:
-    items:
-      - const: sifive,fu540-c000-plic
-      - const: sifive,plic-1.0.0
+    oneOf:
+      - items:
+          - const: sifive,fu540-c000-plic
+          - const: sifive,plic-1.0.0
+
+      - items:
+          - const: sifive,plic-1.0.0
 
   reg:
     maxItems: 1
-- 
2.29.2

[PATCH v12 04/17] dt-bindings: add Canaan boards compatible strings

[Damien Le Moal]

Introduce the file riscv/canaan.yaml to document compatible strings
related to the Canaan Kendryte K210 SoC. The compatible string
"canaan,kendryte-k210" used to indicate the use of this SoC to the
early SoC init code is added. This new file also defines the compatible
strings of all supported boards based on this SoC.

Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
---
 .../devicetree/bindings/riscv/canaan.yaml     | 47 +++++++++++++++++++
 1 file changed, 47 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/riscv/canaan.yaml

diff --git a/Documentation/devicetree/bindings/riscv/canaan.yaml b/Documentation/devicetree/bindings/riscv/canaan.yaml
new file mode 100644
index 000000000000..f8f3f286bd55
--- /dev/null
+++ b/Documentation/devicetree/bindings/riscv/canaan.yaml
@@ -0,0 +1,47 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/riscv/canaan.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Canaan SoC-based boards
+
+maintainers:
+  - Damien Le Moal <damien.lemoal@wdc.com>
+
+description:
+  Canaan Kendryte K210 SoC-based boards
+
+properties:
+  $nodename:
+    const: '/'
+  compatible:
+    oneOf:
+      - items:
+          - const: sipeed,maix-bit
+          - const: sipeed,maix-bitm
+          - const: canaan,kendryte-k210
+
+      - items:
+          - const: sipeed,maix-go
+          - const: canaan,kendryte-k210
+
+      - items:
+          - const: sipeed,maix-dock-m1
+          - const: sipeed,maix-dock-m1w
+          - const: canaan,kendryte-k210
+
+      - items:
+          - const: sipeed,maixduino
+          - const: canaan,kendryte-k210
+
+      - items:
+          - const: canaan,kendryte-kd233
+          - const: canaan,kendryte-k210
+
+      - items:
+          - const: canaan,kendryte-k210
+
+additionalProperties: true
+
+...
-- 
2.29.2

[PATCH v12 05/17] dt-bindings: fix sifive gpio properties

[Damien Le Moal]

The sifive gpio IP block supports up to 32 GPIOs. Reflect that in the
interrupts property description and maxItems. Also add the standard
ngpios property to describe the number of GPIOs available on the
implementation.

Also add the "canaan,k210-gpiohs" compatible string for the Canaan K210
SoC which uses the Sifive gpio IP block. For this compatible string,
do not define the clocks property as required as the K210 SoC does not
have a software controllable clock for the Sifive gpio block.

Cc: Yash Shah <yash.shah@sifive.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
---
 .../devicetree/bindings/gpio/sifive,gpio.yaml | 21 ++++++++++++++++---
 1 file changed, 18 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/gpio/sifive,gpio.yaml b/Documentation/devicetree/bindings/gpio/sifive,gpio.yaml
index ab22056f8b44..2cef18ca737c 100644
--- a/Documentation/devicetree/bindings/gpio/sifive,gpio.yaml
+++ b/Documentation/devicetree/bindings/gpio/sifive,gpio.yaml
@@ -16,6 +16,7 @@ properties:
       - enum:
           - sifive,fu540-c000-gpio
           - sifive,fu740-c000-gpio
+          - canaan,k210-gpiohs
       - const: sifive,gpio0
 
   reg:
@@ -23,9 +24,9 @@ properties:
 
   interrupts:
     description:
-      interrupt mapping one per GPIO. Maximum 16 GPIOs.
+      interrupt mapping one per GPIO. Maximum 32 GPIOs.
     minItems: 1
-    maxItems: 16
+    maxItems: 32
 
   interrupt-controller: true
 
@@ -38,6 +39,10 @@ properties:
   "#gpio-cells":
     const: 2
 
+  ngpios:
+    minimum: 1
+    maximum: 32
+
   gpio-controller: true
 
 required:
@@ -46,10 +51,20 @@ required:
   - interrupts
   - interrupt-controller
   - "#interrupt-cells"
-  - clocks
   - "#gpio-cells"
   - gpio-controller
 
+if:
+  properties:
+    compatible:
+      contains:
+        enum:
+          - sifive,fu540-c000-gpio
+          - sifive,fu740-c000-gpio
+then:
+  required:
+    - clocks
+
 additionalProperties: false
 
 examples:
-- 
2.29.2

[PATCH v12 06/17] dt-bindings: add resets property to dw-apb-timer

[Damien Le Moal]

The Synopsis DesignWare APB timer driver
(drivers/clocksource/dw_apb_timer_of.c) indirectly uses the resets
property of its node as it executes the function of_reset_control_get().
Make sure that this property is documented in
timer/snps,dw-apb-timer.yaml to avoid make dtbs_check warnings.

Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
---
 Documentation/devicetree/bindings/timer/snps,dw-apb-timer.yaml | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/timer/snps,dw-apb-timer.yaml b/Documentation/devicetree/bindings/timer/snps,dw-apb-timer.yaml
index d65faf289a83..d33c9205a909 100644
--- a/Documentation/devicetree/bindings/timer/snps,dw-apb-timer.yaml
+++ b/Documentation/devicetree/bindings/timer/snps,dw-apb-timer.yaml
@@ -24,6 +24,9 @@ properties:
   interrupts:
     maxItems: 1
 
+  resets:
+    maxItems: 1
+
   clocks:
     minItems: 1
     items:
-- 
2.29.2

[PATCH v12 07/17] dt-bindings: update risc-v cpu properties

[Damien Le Moal]

The Canaan Kendryte K210 SoC CPU cores are based on a rocket chip
version using a draft verion of the RISC-V ISA specifications. To avoid
any confusion with CPU cores using stable specifications, add the
compatible string "canaan,k210" for this SoC CPU cores.

Also add the "riscv,none" value to the mmu-type property to allow a DT
to indicate that the CPU being described does not have an MMU or that
it has an MMU that is not usable (which is the case for the K210 SoC).

Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
---
 Documentation/devicetree/bindings/riscv/cpus.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/riscv/cpus.yaml b/Documentation/devicetree/bindings/riscv/cpus.yaml
index eb6843f69f7c..e534f6a7cfa1 100644
--- a/Documentation/devicetree/bindings/riscv/cpus.yaml
+++ b/Documentation/devicetree/bindings/riscv/cpus.yaml
@@ -39,6 +39,7 @@ properties:
               - sifive,u74
               - sifive,u5
               - sifive,u7
+              - canaan,k210
           - const: riscv
       - const: riscv    # Simulator only
     description:
@@ -56,6 +57,7 @@ properties:
       - riscv,sv32
       - riscv,sv39
       - riscv,sv48
+      - riscv,none
 
   riscv,isa:
     description:
-- 
2.29.2

[PATCH v12 08/17] dt-bindings: fix sifive clint compatible string

[Damien Le Moal]

Fix the Sifive clint compatible string definition to make the value
"sifive,fu540-c000-clint" optional, allowing a DT to specify only
"sifive,clint0" for its generic implementation without any tweak.
With this change, a Sifive clint node can now be defined as explained
in the compatible string description.

Cc: Anup Patel <anup.patel@wdc.com>
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
---
 .../devicetree/bindings/timer/sifive,clint.yaml          | 9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)

diff --git a/Documentation/devicetree/bindings/timer/sifive,clint.yaml b/Documentation/devicetree/bindings/timer/sifive,clint.yaml
index 2a0e9cd9fbcf..c6b1f37a2949 100644
--- a/Documentation/devicetree/bindings/timer/sifive,clint.yaml
+++ b/Documentation/devicetree/bindings/timer/sifive,clint.yaml
@@ -22,12 +22,13 @@ description:
 
 properties:
   compatible:
-    items:
-      - const: sifive,fu540-c000-clint
-      - const: sifive,clint0
+    oneOf:
+      - items:
+          - enum:
+              - sifive,fu540-c000-clint
+              - sifive,clint0
 
     description:
-      Should be "sifive,<chip>-clint" and "sifive,clint<version>".
       Supported compatible strings are -
       "sifive,fu540-c000-clint" for the SiFive CLINT v0 as integrated
       onto the SiFive FU540 chip, and "sifive,clint0" for the SiFive
-- 
2.29.2

Re: [PATCH v12 08/17] dt-bindings: fix sifive clint compatible string

[Rob Herring]

On Fri, 15 Jan 2021 23:03:43 +0900, Damien Le Moal wrote:
> Fix the Sifive clint compatible string definition to make the value
> "sifive,fu540-c000-clint" optional, allowing a DT to specify only
> "sifive,clint0" for its generic implementation without any tweak.
> With this change, a Sifive clint node can now be defined as explained
> in the compatible string description.
> 
> Cc: Anup Patel <anup.patel@wdc.com>
> Cc: Rob Herring <robh@kernel.org>
> Cc: devicetree@vger.kernel.org
> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
> ---
>  .../devicetree/bindings/timer/sifive,clint.yaml          | 9 +++++----
>  1 file changed, 5 insertions(+), 4 deletions(-)
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/timer/sifive,clint.example.dt.yaml: timer@2000000: compatible: 'oneOf' conditional failed, one must be fixed:
	['sifive,fu540-c000-clint', 'sifive,clint0'] is too long
	Additional items are not allowed ('sifive,clint0' was unexpected)
	From schema: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/timer/sifive,clint.yaml

See https://patchwork.ozlabs.org/patch/1427053

This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit.

Re: [PATCH v12 08/17] dt-bindings: fix sifive clint compatible string

[Rob Herring]

On Fri, Jan 15, 2021 at 11:03:43PM +0900, Damien Le Moal wrote:
> Fix the Sifive clint compatible string definition to make the value
> "sifive,fu540-c000-clint" optional, allowing a DT to specify only
> "sifive,clint0" for its generic implementation without any tweak.
> With this change, a Sifive clint node can now be defined as explained
> in the compatible string description.

NACK.

How do you know you'll never need some tweak? Adding it to the DT later 
defeats the whole point of not having to do DT updates to implement 
work-arounds and/or enhancements.

> 
> Cc: Anup Patel <anup.patel@wdc.com>
> Cc: Rob Herring <robh@kernel.org>
> Cc: devicetree@vger.kernel.org
> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
> ---
>  .../devicetree/bindings/timer/sifive,clint.yaml          | 9 +++++----
>  1 file changed, 5 insertions(+), 4 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/timer/sifive,clint.yaml b/Documentation/devicetree/bindings/timer/sifive,clint.yaml
> index 2a0e9cd9fbcf..c6b1f37a2949 100644
> --- a/Documentation/devicetree/bindings/timer/sifive,clint.yaml
> +++ b/Documentation/devicetree/bindings/timer/sifive,clint.yaml
> @@ -22,12 +22,13 @@ description:
>  
>  properties:
>    compatible:
> -    items:
> -      - const: sifive,fu540-c000-clint
> -      - const: sifive,clint0
> +    oneOf:
> +      - items:
> +          - enum:
> +              - sifive,fu540-c000-clint
> +              - sifive,clint0
>  
>      description:
> -      Should be "sifive,<chip>-clint" and "sifive,clint<version>".
>        Supported compatible strings are -
>        "sifive,fu540-c000-clint" for the SiFive CLINT v0 as integrated
>        onto the SiFive FU540 chip, and "sifive,clint0" for the SiFive
> -- 
> 2.29.2
> 

[PATCH v12 09/17] dt-bindings: update sifive serial

[Damien Le Moal]

Add the compatible string "canaan,k210-uarths" to the sifive uart
bindings as the Canaan Kendryte K210 includes a Sifive uart IP block for
the main serial console.

Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
---
 Documentation/devicetree/bindings/serial/sifive-serial.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/serial/sifive-serial.yaml b/Documentation/devicetree/bindings/serial/sifive-serial.yaml
index 3ac5c7ff2758..5fa94dacbba9 100644
--- a/Documentation/devicetree/bindings/serial/sifive-serial.yaml
+++ b/Documentation/devicetree/bindings/serial/sifive-serial.yaml
@@ -20,6 +20,7 @@ properties:
       - enum:
           - sifive,fu540-c000-uart
           - sifive,fu740-c000-uart
+          - canaan,k210-uarths
       - const: sifive,uart0
 
     description:
-- 
2.29.2

[PATCH v12 10/17] riscv: Update Canaan Kendryte K210 device tree

[Damien Le Moal]

Update the Canaan Kendryte K210 base device tree k210.dtsi to define
all peripherals of the SoC, their clocks and reset lines. The device
tree file k210.dts is renamed to k210_generic.dts and becomes the
default value selection of the SOC_CANAAN_K210_DTB_BUILTIN_SOURCE
configuration option. No device beside the serial console is defined by
this device tree. This makes this generic device tree suitable for use
with a builtin initramfs with all known K210 based boards.

These changes result in the K210_CLK_ACLK clock ID to be unused and
removed from the dt-bindings k210-clk.h header file.

Most updates to the k210.dtsi file come from Sean Anderson's work on
U-Boot support for the K210.

Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
---
 arch/riscv/Kconfig.socs                     |   2 +-
 arch/riscv/boot/dts/canaan/k210.dts         |  23 -
 arch/riscv/boot/dts/canaan/k210.dtsi        | 535 +++++++++++++++++++-
 arch/riscv/boot/dts/canaan/k210_generic.dts |  46 ++
 include/dt-bindings/clock/k210-clk.h        |   1 -
 5 files changed, 554 insertions(+), 53 deletions(-)
 delete mode 100644 arch/riscv/boot/dts/canaan/k210.dts
 create mode 100644 arch/riscv/boot/dts/canaan/k210_generic.dts

diff --git a/arch/riscv/Kconfig.socs b/arch/riscv/Kconfig.socs
index 6402746c68f3..7efcece8896c 100644
--- a/arch/riscv/Kconfig.socs
+++ b/arch/riscv/Kconfig.socs
@@ -51,7 +51,7 @@ config SOC_CANAAN_K210_DTB_SOURCE
 	string "Source file for the Canaan Kendryte K210 builtin DTB"
 	depends on SOC_CANAAN
 	depends on SOC_CANAAN_K210_DTB_BUILTIN
-	default "k210"
+	default "k210_generic"
 	help
 	  Base name (without suffix, relative to arch/riscv/boot/dts/canaan)
 	  for the DTS file that will be used to produce the DTB linked into the
diff --git a/arch/riscv/boot/dts/canaan/k210.dts b/arch/riscv/boot/dts/canaan/k210.dts
deleted file mode 100644
index 0d1f28fce6b2..000000000000
--- a/arch/riscv/boot/dts/canaan/k210.dts
+++ /dev/null
@@ -1,23 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2020 Western Digital Corporation or its affiliates.
- */
-
-/dts-v1/;
-
-#include "k210.dtsi"
-
-/ {
-	model = "Kendryte K210 generic";
-	compatible = "kendryte,k210";
-
-	chosen {
-		bootargs = "earlycon console=ttySIF0";
-		stdout-path = "serial0";
-	};
-};
-
-&uarths0 {
-	status = "okay";
-};
-
diff --git a/arch/riscv/boot/dts/canaan/k210.dtsi b/arch/riscv/boot/dts/canaan/k210.dtsi
index 354b263195a3..995c044e7b60 100644
--- a/arch/riscv/boot/dts/canaan/k210.dtsi
+++ b/arch/riscv/boot/dts/canaan/k210.dtsi
@@ -1,9 +1,11 @@
 // SPDX-License-Identifier: GPL-2.0+
 /*
- * Copyright (C) 2019 Sean Anderson <seanga2@gmail.com>
+ * Copyright (C) 2019-20 Sean Anderson <seanga2@gmail.com>
  * Copyright (C) 2020 Western Digital Corporation or its affiliates.
  */
 #include <dt-bindings/clock/k210-clk.h>
+#include <dt-bindings/pinctrl/k210-fpioa.h>
+#include <dt-bindings/reset/k210-rst.h>
 
 / {
 	/*
@@ -12,14 +14,33 @@ / {
 	 */
 	#address-cells = <1>;
 	#size-cells = <1>;
-	compatible = "kendryte,k210";
+	compatible = "canaan,kendryte-k210";
 
 	aliases {
+		cpu0 = &cpu0;
+		cpu1 = &cpu1;
+		dma0 = &dmac0;
+		gpio0 = &gpio0;
+		gpio1 = &gpio1_0;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		pinctrl0 = &fpioa;
 		serial0 = &uarths0;
+		serial1 = &uart1;
+		serial2 = &uart2;
+		serial3 = &uart3;
+		spi0 = &spi0;
+		spi1 = &spi1;
+		spi2 = &spi2;
+		spi3 = &spi3;
+		timer0 = &timer0;
+		timer1 = &timer1;
+		timer2 = &timer2;
 	};
 
 	/*
-	 * The K210 has an sv39 MMU following the priviledge specification v1.9.
+	 * The K210 has an sv39 MMU following the privileged specification v1.9.
 	 * Since this is a non-ratified draft specification, the kernel does not
 	 * support it and the K210 support enabled only for the !MMU case.
 	 * Be consistent with this by setting the CPUs MMU type to "none".
@@ -30,14 +51,14 @@ cpus {
 		timebase-frequency = <7800000>;
 		cpu0: cpu@0 {
 			device_type = "cpu";
+			compatible = "canaan,k210", "riscv";
 			reg = <0>;
-			compatible = "kendryte,k210", "sifive,rocket0", "riscv";
 			riscv,isa = "rv64imafdc";
-			mmu-type = "none";
-			i-cache-size = <0x8000>;
+			mmu-type = "riscv,none";
 			i-cache-block-size = <64>;
-			d-cache-size = <0x8000>;
+			i-cache-size = <0x8000>;
 			d-cache-block-size = <64>;
+			d-cache-size = <0x8000>;
 			cpu0_intc: interrupt-controller {
 				#interrupt-cells = <1>;
 				interrupt-controller;
@@ -46,14 +67,14 @@ cpu0_intc: interrupt-controller {
 		};
 		cpu1: cpu@1 {
 			device_type = "cpu";
+			compatible = "canaan,k210", "riscv";
 			reg = <1>;
-			compatible = "kendryte,k210", "sifive,rocket0", "riscv";
 			riscv,isa = "rv64imafdc";
-			mmu-type = "none";
-			i-cache-size = <0x8000>;
+			mmu-type = "riscv,none";
 			i-cache-block-size = <64>;
-			d-cache-size = <0x8000>;
+			i-cache-size = <0x8000>;
 			d-cache-block-size = <64>;
+			d-cache-size = <0x8000>;
 			cpu1_intc: interrupt-controller {
 				#interrupt-cells = <1>;
 				interrupt-controller;
@@ -64,10 +85,15 @@ cpu1_intc: interrupt-controller {
 
 	sram: memory@80000000 {
 		device_type = "memory";
+		compatible = "canaan,k210-sram";
 		reg = <0x80000000 0x400000>,
 		      <0x80400000 0x200000>,
 		      <0x80600000 0x200000>;
 		reg-names = "sram0", "sram1", "aisram";
+		clocks = <&sysclk K210_CLK_SRAM0>,
+			 <&sysclk K210_CLK_SRAM1>,
+			 <&sysclk K210_CLK_AI>;
+		clock-names = "sram0", "sram1", "aisram";
 	};
 
 	clocks {
@@ -81,40 +107,493 @@ in0: oscillator {
 	soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "kendryte,k210-soc", "simple-bus";
+		compatible = "simple-bus";
 		ranges;
 		interrupt-parent = <&plic0>;
 
-		sysctl: sysctl@50440000 {
-			compatible = "kendryte,k210-sysctl", "simple-mfd";
-			reg = <0x50440000 0x1000>;
-			#clock-cells = <1>;
+		debug0: debug@0 {
+			compatible = "canaan,k210-debug", "riscv,debug";
+			reg = <0x0 0x1000>;
+			status = "disabled";
+		};
+
+		rom0: nvmem@1000 {
+			reg = <0x1000 0x1000>;
+			read-only;
+			status = "disabled";
 		};
 
 		clint0: clint@2000000 {
-			#interrupt-cells = <1>;
-			compatible = "riscv,clint0";
+			compatible = "sifive,clint0";
 			reg = <0x2000000 0xC000>;
-			interrupts-extended =  <&cpu0_intc 3 &cpu0_intc 7
-						&cpu1_intc 3 &cpu1_intc 7>;
+			interrupts-extended = <&cpu0_intc 3 &cpu0_intc 7
+					      &cpu1_intc 3 &cpu1_intc 7>;
 		};
 
-		plic0: interrupt-controller@c000000 {
+		plic0: interrupt-controller@C000000 {
 			#interrupt-cells = <1>;
-			interrupt-controller;
-			compatible = "kendryte,k210-plic0", "riscv,plic0";
+			#address-cells = <0>;
+			compatible = "sifive,plic-1.0.0";
 			reg = <0xC000000 0x4000000>;
-			interrupts-extended = <&cpu0_intc 11>, <&cpu0_intc 0xffffffff>,
-					      <&cpu1_intc 11>, <&cpu1_intc 0xffffffff>;
+			interrupt-controller;
+			interrupts-extended = <&cpu0_intc 11 &cpu1_intc 11>;
 			riscv,ndev = <65>;
-			riscv,max-priority = <7>;
 		};
 
 		uarths0: serial@38000000 {
-			compatible = "kendryte,k210-uarths", "sifive,uart0";
+			compatible = "canaan,k210-uarths", "sifive,uart0";
 			reg = <0x38000000 0x1000>;
 			interrupts = <33>;
-			clocks = <&sysctl K210_CLK_CPU>;
+			clocks = <&sysclk K210_CLK_CPU>;
+			status = "disabled";
+		};
+
+		gpio0: gpio-controller@38001000 {
+			#interrupt-cells = <2>;
+			#gpio-cells = <2>;
+			compatible = "canaan,k210-gpiohs", "sifive,gpio0";
+			reg = <0x38001000 0x1000>;
+			interrupt-controller;
+			interrupts = <34 35 36 37 38 39 40 41
+				      42 43 44 45 46 47 48 49
+				      50 51 52 53 54 55 56 57
+				      58 59 60 61 62 63 64 65>;
+			gpio-controller;
+			ngpios = <32>;
+			status = "disabled";
+		};
+
+		kpu0: kpu@40800000 {
+			compatible = "canaan,k210-kpu";
+			reg = <0x40800000 0xc00000>;
+			interrupts = <25>;
+			clocks = <&sysclk K210_CLK_AI>;
+			status = "disabled";
+		};
+
+		fft0: fft@42000000 {
+			compatible = "canaan,k210-fft";
+			reg = <0x42000000 0x400000>;
+			interrupts = <26>;
+			clocks = <&sysclk K210_CLK_FFT>;
+			resets = <&sysrst K210_RST_FFT>;
+			status = "disabled";
+		};
+
+		dmac0: dma-controller@50000000 {
+			compatible = "snps,axi-dma-1.01a";
+			reg = <0x50000000 0x1000>;
+			interrupts = <27 28 29 30 31 32>;
+			clocks = <&sysclk K210_CLK_DMA>, <&sysclk K210_CLK_DMA>;
+			clock-names = "core-clk", "cfgr-clk";
+			resets = <&sysrst K210_RST_DMA>;
+			dma-channels = <6>;
+			snps,dma-masters = <2>;
+			snps,priority = <0 1 2 3 4 5>;
+			snps,data-width = <5>;
+			snps,block-size = <0x200000 0x200000 0x200000
+					   0x200000 0x200000 0x200000>;
+			snps,axi-max-burst-len = <256>;
+			status = "disabled";
+		};
+
+		apb0: bus@50200000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "simple-pm-bus";
+			ranges;
+			clocks = <&sysclk K210_CLK_APB0>;
+
+			gpio1: gpio@50200000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "snps,dw-apb-gpio";
+				reg = <0x50200000 0x80>;
+				clocks = <&sysclk K210_CLK_APB0>,
+					 <&sysclk K210_CLK_GPIO>;
+				clock-names = "bus", "db";
+				resets = <&sysrst K210_RST_GPIO>;
+				status = "disabled";
+
+				gpio1_0: gpio-port@0 {
+					#gpio-cells = <2>;
+					#interrupt-cells = <2>;
+					compatible = "snps,dw-apb-gpio-port";
+					reg = <0>;
+					interrupt-controller;
+					interrupts = <23>;
+					gpio-controller;
+					ngpios = <8>;
+				};
+			};
+
+			uart1: serial@50210000 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x50210000 0x100>;
+				interrupts = <11>;
+				clocks = <&sysclk K210_CLK_UART1>,
+					 <&sysclk K210_CLK_APB0>;
+				clock-names = "baudclk", "apb_pclk";
+				resets = <&sysrst K210_RST_UART1>;
+				reg-io-width = <4>;
+				reg-shift = <2>;
+				dcd-override;
+				dsr-override;
+				cts-override;
+				ri-override;
+				status = "disabled";
+			};
+
+			uart2: serial@50220000 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x50220000 0x100>;
+				interrupts = <12>;
+				clocks = <&sysclk K210_CLK_UART2>,
+					 <&sysclk K210_CLK_APB0>;
+				clock-names = "baudclk", "apb_pclk";
+				resets = <&sysrst K210_RST_UART2>;
+				reg-io-width = <4>;
+				reg-shift = <2>;
+				dcd-override;
+				dsr-override;
+				cts-override;
+				ri-override;
+				status = "disabled";
+			};
+
+			uart3: serial@50230000 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x50230000 0x100>;
+				interrupts = <13>;
+				clocks = <&sysclk K210_CLK_UART3>,
+					 <&sysclk K210_CLK_APB0>;
+				clock-names = "baudclk", "apb_pclk";
+				resets = <&sysrst K210_RST_UART3>;
+				reg-io-width = <4>;
+				reg-shift = <2>;
+				dcd-override;
+				dsr-override;
+				cts-override;
+				ri-override;
+				status = "disabled";
+			};
+
+			spi2: spi@50240000 {
+				compatible = "canaan,k210-spi";
+				spi-slave;
+				reg = <0x50240000 0x100>;
+				interrupts = <3>;
+				clocks = <&sysclk K210_CLK_SPI2>,
+					 <&sysclk K210_CLK_APB0>;
+				clock-names = "ssi_clk", "pclk";
+				resets = <&sysrst K210_RST_SPI2>;
+				spi-max-frequency = <25000000>;
+				status = "disabled";
+			};
+
+			i2s0: i2s@50250000 {
+				compatible = "snps,designware-i2s";
+				reg = <0x50250000 0x200>;
+				interrupts = <5>;
+				clocks = <&sysclk K210_CLK_I2S0>;
+				clock-names = "i2sclk";
+				resets = <&sysrst K210_RST_I2S0>;
+				status = "disabled";
+			};
+
+			apu0: sound@520250200 {
+				compatible = "canaan,k210-apu";
+				reg = <0x50250200 0x200>;
+				status = "disabled";
+			};
+
+			i2s1: i2s@50260000 {
+				compatible = "snps,designware-i2s";
+				reg = <0x50260000 0x200>;
+				interrupts = <6>;
+				clocks = <&sysclk K210_CLK_I2S1>;
+				clock-names = "i2sclk";
+				resets = <&sysrst K210_RST_I2S1>;
+				status = "disabled";
+			};
+
+			i2s2: i2s@50270000 {
+				compatible = "snps,designware-i2s";
+				reg = <0x50270000 0x200>;
+				interrupts = <7>;
+				clocks = <&sysclk K210_CLK_I2S2>;
+				clock-names = "i2sclk";
+				resets = <&sysrst K210_RST_I2S2>;
+				status = "disabled";
+			};
+
+			i2c0: i2c@50280000 {
+				compatible = "snps,designware-i2c";
+				reg = <0x50280000 0x100>;
+				interrupts = <8>;
+				clocks = <&sysclk K210_CLK_I2C0>,
+					 <&sysclk K210_CLK_APB0>;
+				clock-names = "ref", "pclk";
+				resets = <&sysrst K210_RST_I2C0>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@50290000 {
+				compatible = "snps,designware-i2c";
+				reg = <0x50290000 0x100>;
+				interrupts = <9>;
+				clocks = <&sysclk K210_CLK_I2C1>,
+					 <&sysclk K210_CLK_APB0>;
+				clock-names = "ref", "pclk";
+				resets = <&sysrst K210_RST_I2C1>;
+				status = "disabled";
+			};
+
+			i2c2: i2c@502A0000 {
+				compatible = "snps,designware-i2c";
+				reg = <0x502A0000 0x100>;
+				interrupts = <10>;
+				clocks = <&sysclk K210_CLK_I2C2>,
+					 <&sysclk K210_CLK_APB0>;
+				clock-names = "ref", "pclk";
+				resets = <&sysrst K210_RST_I2C2>;
+				status = "disabled";
+			};
+
+			fpioa: pinmux@502B0000 {
+				compatible = "canaan,k210-fpioa";
+				reg = <0x502B0000 0x100>;
+				clocks = <&sysclk K210_CLK_FPIOA>,
+					 <&sysclk K210_CLK_APB0>;
+				clock-names = "ref", "pclk";
+				resets = <&sysrst K210_RST_FPIOA>;
+				canaan,k210-sysctl-power = <&sysctl 108>;
+				status = "disabled";
+			};
+
+			sha256: sha256@502C0000 {
+				compatible = "canaan,k210-sha256";
+				reg = <0x502C0000 0x100>;
+				clocks = <&sysclk K210_CLK_SHA>;
+				resets = <&sysrst K210_RST_SHA>;
+				status = "disabled";
+			};
+
+			timer0: timer@502D0000 {
+				compatible = "snps,dw-apb-timer";
+				reg = <0x502D0000 0x100>;
+				interrupts = <14 15>;
+				clocks = <&sysclk K210_CLK_TIMER0>,
+					 <&sysclk K210_CLK_APB0>;
+				clock-names = "timer", "pclk";
+				resets = <&sysrst K210_RST_TIMER0>;
+				status = "disabled";
+			};
+
+			timer1: timer@502E0000 {
+				compatible = "snps,dw-apb-timer";
+				reg = <0x502E0000 0x100>;
+				interrupts = <16 17>;
+				clocks = <&sysclk K210_CLK_TIMER1>,
+					 <&sysclk K210_CLK_APB0>;
+				clock-names = "timer", "pclk";
+				resets = <&sysrst K210_RST_TIMER1>;
+				status = "disabled";
+			};
+
+			timer2: timer@502F0000 {
+				compatible = "snps,dw-apb-timer";
+				reg = <0x502F0000 0x100>;
+				interrupts = <18 19>;
+				clocks = <&sysclk K210_CLK_TIMER2>,
+					 <&sysclk K210_CLK_APB0>;
+				clock-names = "timer", "pclk";
+				resets = <&sysrst K210_RST_TIMER2>;
+				status = "disabled";
+			};
+		};
+
+		apb1: bus@50400000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "simple-pm-bus";
+			ranges;
+			clocks = <&sysclk K210_CLK_APB1>;
+
+			wdt0: watchdog@50400000 {
+				compatible = "snps,dw-wdt";
+				reg = <0x50400000 0x100>;
+				interrupts = <21>;
+				clocks = <&sysclk K210_CLK_WDT0>,
+					 <&sysclk K210_CLK_APB1>;
+				clock-names = "tclk", "pclk";
+				resets = <&sysrst K210_RST_WDT0>;
+				status = "disabled";
+			};
+
+			wdt1: watchdog@50410000 {
+				compatible = "snps,dw-wdt";
+				reg = <0x50410000 0x100>;
+				interrupts = <22>;
+				clocks = <&sysclk K210_CLK_WDT1>,
+					 <&sysclk K210_CLK_APB1>;
+				clock-names = "tclk", "pclk";
+				resets = <&sysrst K210_RST_WDT1>;
+				status = "disabled";
+			};
+
+			otp0: nvmem@50420000 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "canaan,k210-otp";
+				reg = <0x50420000 0x100>,
+				      <0x88000000 0x20000>;
+				reg-names = "reg", "mem";
+				clocks = <&sysclk K210_CLK_ROM>;
+				resets = <&sysrst K210_RST_ROM>;
+				read-only;
+				status = "disabled";
+
+				/* Bootloader */
+				firmware@00000 {
+					reg = <0x00000 0xC200>;
+				};
+
+				/*
+				 * config string as described in RISC-V
+				 * privileged spec 1.9
+				 */
+				config-1-9@1c000 {
+					reg = <0x1C000 0x1000>;
+				};
+
+				/*
+				 * Device tree containing only registers,
+				 * interrupts, and cpus
+				 */
+				fdt@1d000 {
+					reg = <0x1D000 0x2000>;
+				};
+
+				/* CPU/ROM credits */
+				credits@1f000 {
+					reg = <0x1F000 0x1000>;
+				};
+			};
+
+			dvp0: camera@50430000 {
+				compatible = "canaan,k210-dvp";
+				reg = <0x50430000 0x100>;
+				interrupts = <24>;
+				clocks = <&sysclk K210_CLK_DVP>;
+				resets = <&sysrst K210_RST_DVP>;
+				canaan,k210-misc-offset = <&sysctl 84>;
+				status = "disabled";
+			};
+
+			sysctl: syscon@50440000 {
+				compatible = "canaan,k210-sysctl",
+					     "syscon", "simple-mfd";
+				reg = <0x50440000 0x100>;
+				clocks = <&sysclk K210_CLK_APB1>;
+				clock-names = "pclk";
+
+				sysclk: clock-controller {
+					#clock-cells = <1>;
+					compatible = "canaan,k210-clk";
+					clocks = <&in0>;
+				};
+
+				sysrst: reset-controller {
+					compatible = "canaan,k210-rst";
+					#reset-cells = <1>;
+				};
+
+				reboot: syscon-reboot {
+					compatible = "syscon-reboot";
+					regmap = <&sysctl>;
+					offset = <48>;
+					mask = <1>;
+					value = <1>;
+				};
+			};
+
+			aes0: aes@50450000 {
+				compatible = "canaan,k210-aes";
+				reg = <0x50450000 0x100>;
+				clocks = <&sysclk K210_CLK_AES>;
+				resets = <&sysrst K210_RST_AES>;
+				status = "disabled";
+			};
+
+			rtc: rtc@50460000 {
+				compatible = "canaan,k210-rtc";
+				reg = <0x50460000 0x100>;
+				clocks = <&in0>;
+				resets = <&sysrst K210_RST_RTC>;
+				interrupts = <20>;
+				status = "disabled";
+			};
+		};
+
+		apb2: bus@52000000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "simple-pm-bus";
+			ranges;
+			clocks = <&sysclk K210_CLK_APB2>;
+
+			spi0: spi@52000000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "canaan,k210-spi";
+				reg = <0x52000000 0x100>;
+				interrupts = <1>;
+				clocks = <&sysclk K210_CLK_SPI0>,
+					 <&sysclk K210_CLK_APB2>;
+				clock-names = "ssi_clk", "pclk";
+				resets = <&sysrst K210_RST_SPI0>;
+				reset-names = "spi";
+				spi-max-frequency = <25000000>;
+				num-cs = <4>;
+				reg-io-width = <4>;
+				status = "disabled";
+			};
+
+			spi1: spi@53000000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "canaan,k210-spi";
+				reg = <0x53000000 0x100>;
+				interrupts = <2>;
+				clocks = <&sysclk K210_CLK_SPI1>,
+					 <&sysclk K210_CLK_APB2>;
+				clock-names = "ssi_clk", "pclk";
+				resets = <&sysrst K210_RST_SPI1>;
+				reset-names = "spi";
+				spi-max-frequency = <25000000>;
+				num-cs = <4>;
+				reg-io-width = <4>;
+				status = "disabled";
+			};
+
+			spi3: spi@54000000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "snps,dwc-ssi-1.01a";
+				reg = <0x54000000 0x200>;
+				interrupts = <4>;
+				clocks = <&sysclk K210_CLK_SPI3>,
+					 <&sysclk K210_CLK_APB2>;
+				clock-names = "ssi_clk", "pclk";
+				resets = <&sysrst K210_RST_SPI3>;
+				reset-names = "spi";
+				/* Could possibly go up to 200 MHz */
+				spi-max-frequency = <100000000>;
+				num-cs = <4>;
+				reg-io-width = <4>;
+				status = "disabled";
+			};
 		};
 	};
 };
diff --git a/arch/riscv/boot/dts/canaan/k210_generic.dts b/arch/riscv/boot/dts/canaan/k210_generic.dts
new file mode 100644
index 000000000000..396c8ca4d24d
--- /dev/null
+++ b/arch/riscv/boot/dts/canaan/k210_generic.dts
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2019-20 Sean Anderson <seanga2@gmail.com>
+ * Copyright (C) 2020 Western Digital Corporation or its affiliates.
+ */
+
+/dts-v1/;
+
+#include "k210.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Kendryte K210 generic";
+	compatible = "canaan,kendryte-k210";
+
+	chosen {
+		bootargs = "earlycon console=ttySIF0";
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&fpioa {
+	pinctrl-0 = <&jtag_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	jtag_pins: jtag-pinmux {
+		pinmux = <K210_FPIOA(0, K210_PCF_JTAG_TCLK)>,
+			 <K210_FPIOA(1, K210_PCF_JTAG_TDI)>,
+			 <K210_FPIOA(2, K210_PCF_JTAG_TMS)>,
+			 <K210_FPIOA(3, K210_PCF_JTAG_TDO)>;
+	};
+
+	uarths_pins: uarths-pinmux {
+		pinmux = <K210_FPIOA(4, K210_PCF_UARTHS_RX)>,
+			 <K210_FPIOA(5, K210_PCF_UARTHS_TX)>;
+	};
+};
+
+&uarths0 {
+	pinctrl-0 = <&uarths_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
diff --git a/include/dt-bindings/clock/k210-clk.h b/include/dt-bindings/clock/k210-clk.h
index a48176ad3c23..b2de702cbf75 100644
--- a/include/dt-bindings/clock/k210-clk.h
+++ b/include/dt-bindings/clock/k210-clk.h
@@ -9,7 +9,6 @@
 /*
  * Kendryte K210 SoC clock identifiers (arbitrary values).
  */
-#define K210_CLK_ACLK	0
 #define K210_CLK_CPU	0
 #define K210_CLK_SRAM0	1
 #define K210_CLK_SRAM1	2
-- 
2.29.2

[PATCH v12 11/17] riscv: Add SiPeed MAIX BiT board device tree

[Damien Le Moal]

Add the device tree sipeed_maix_bit.dts for the SiPeed MAIX BiT and
MAIX BiTm boards. This device tree enables LEDs, gpio, i2c and spi/mmc
SD card devices.

Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
---
 .../riscv/boot/dts/canaan/sipeed_maix_bit.dts | 234 ++++++++++++++++++
 1 file changed, 234 insertions(+)
 create mode 100644 arch/riscv/boot/dts/canaan/sipeed_maix_bit.dts

diff --git a/arch/riscv/boot/dts/canaan/sipeed_maix_bit.dts b/arch/riscv/boot/dts/canaan/sipeed_maix_bit.dts
new file mode 100644
index 000000000000..11e491410f00
--- /dev/null
+++ b/arch/riscv/boot/dts/canaan/sipeed_maix_bit.dts
@@ -0,0 +1,234 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2019-20 Sean Anderson <seanga2@gmail.com>
+ * Copyright (C) 2020 Western Digital Corporation or its affiliates.
+ */
+
+/dts-v1/;
+
+#include "k210.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "SiPeed MAIX BiT";
+	compatible = "sipeed,maix-bit", "sipeed,maix-bitm",
+		     "canaan,kendryte-k210";
+
+	chosen {
+		bootargs = "earlycon console=ttySIF0";
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		led0 {
+			color = <LED_COLOR_ID_GREEN>;
+			label = "green";
+			gpios = <&gpio1_0 4 GPIO_ACTIVE_LOW>;
+		};
+
+		led1 {
+			color = <LED_COLOR_ID_RED>;
+			label = "red";
+			gpios = <&gpio1_0 5 GPIO_ACTIVE_LOW>;
+		};
+
+		led2 {
+			color = <LED_COLOR_ID_BLUE>;
+			label = "blue";
+			gpios = <&gpio1_0 6 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		boot {
+			label = "BOOT";
+			linux,code = <BTN_0>;
+			gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		status = "disabled";
+
+		simple-audio-card,cpu {
+			sound-dai = <&i2s0 0>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&mic>;
+		};
+	};
+
+	mic: mic {
+		#sound-dai-cells = <0>;
+		compatible = "memsensing,msm261s4030h0";
+		status = "disabled";
+	};
+};
+
+&fpioa {
+	pinctrl-names = "default";
+	pinctrl-0 = <&jtag_pinctrl>;
+	status = "okay";
+
+	jtag_pinctrl: jtag-pinmux {
+		pinmux = <K210_FPIOA(0, K210_PCF_JTAG_TCLK)>,
+			 <K210_FPIOA(1, K210_PCF_JTAG_TDI)>,
+			 <K210_FPIOA(2, K210_PCF_JTAG_TMS)>,
+			 <K210_FPIOA(3, K210_PCF_JTAG_TDO)>;
+	};
+
+	uarths_pinctrl: uarths-pinmux {
+		pinmux = <K210_FPIOA(4, K210_PCF_UARTHS_RX)>,
+			 <K210_FPIOA(5, K210_PCF_UARTHS_TX)>;
+	};
+
+	gpio_pinctrl: gpio-pinmux {
+		pinmux = <K210_FPIOA(8, K210_PCF_GPIO0)>,
+			 <K210_FPIOA(9, K210_PCF_GPIO1)>,
+			 <K210_FPIOA(10, K210_PCF_GPIO2)>,
+			 <K210_FPIOA(11, K210_PCF_GPIO3)>,
+			 <K210_FPIOA(12, K210_PCF_GPIO4)>,
+			 <K210_FPIOA(13, K210_PCF_GPIO5)>,
+			 <K210_FPIOA(14, K210_PCF_GPIO6)>,
+			 <K210_FPIOA(15, K210_PCF_GPIO7)>;
+	};
+
+	gpiohs_pinctrl: gpiohs-pinmux {
+		pinmux = <K210_FPIOA(16, K210_PCF_GPIOHS0)>,
+			 <K210_FPIOA(17, K210_PCF_GPIOHS1)>,
+			 <K210_FPIOA(21, K210_PCF_GPIOHS5)>,
+			 <K210_FPIOA(22, K210_PCF_GPIOHS6)>,
+			 <K210_FPIOA(23, K210_PCF_GPIOHS7)>,
+			 <K210_FPIOA(24, K210_PCF_GPIOHS8)>,
+			 <K210_FPIOA(25, K210_PCF_GPIOHS9)>,
+			 <K210_FPIOA(32, K210_PCF_GPIOHS16)>,
+			 <K210_FPIOA(33, K210_PCF_GPIOHS17)>,
+			 <K210_FPIOA(34, K210_PCF_GPIOHS18)>,
+			 <K210_FPIOA(35, K210_PCF_GPIOHS19)>;
+	};
+
+	i2s0_pinctrl: i2s0-pinmux {
+		pinmux = <K210_FPIOA(18, K210_PCF_I2S0_SCLK)>,
+			 <K210_FPIOA(19, K210_PCF_I2S0_WS)>,
+			 <K210_FPIOA(20, K210_PCF_I2S0_IN_D0)>;
+	};
+
+	dvp_pinctrl: dvp-pinmux {
+		pinmux = <K210_FPIOA(40, K210_PCF_SCCB_SDA)>,
+			 <K210_FPIOA(41, K210_PCF_SCCB_SCLK)>,
+			 <K210_FPIOA(42, K210_PCF_DVP_RST)>,
+			 <K210_FPIOA(43, K210_PCF_DVP_VSYNC)>,
+			 <K210_FPIOA(44, K210_PCF_DVP_PWDN)>,
+			 <K210_FPIOA(45, K210_PCF_DVP_HSYNC)>,
+			 <K210_FPIOA(46, K210_PCF_DVP_XCLK)>,
+			 <K210_FPIOA(47, K210_PCF_DVP_PCLK)>;
+	};
+
+	spi0_pinctrl: spi0-pinmux {
+		pinmux = <K210_FPIOA(36, K210_PCF_GPIOHS20)>,  /* cs */
+			 <K210_FPIOA(37, K210_PCF_GPIOHS21)>,  /* rst */
+			 <K210_FPIOA(38, K210_PCF_GPIOHS22)>,  /* dc */
+			 <K210_FPIOA(39, K210_PCF_SPI0_SCLK)>; /* wr */
+	};
+
+	spi1_pinctrl: spi1-pinmux {
+		pinmux = <K210_FPIOA(26, K210_PCF_SPI1_D1)>,
+			 <K210_FPIOA(27, K210_PCF_SPI1_SCLK)>,
+			 <K210_FPIOA(28, K210_PCF_SPI1_D0)>,
+			 <K210_FPIOA(29, K210_PCF_GPIOHS13)>; /* cs */
+	};
+
+	i2c1_pinctrl: i2c1-pinmux {
+		pinmux = <K210_FPIOA(30, K210_PCF_I2C1_SCLK)>,
+			 <K210_FPIOA(31, K210_PCF_I2C1_SDA)>;
+	};
+};
+
+&uarths0 {
+	pinctrl-0 = <&uarths_pinctrl>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&gpio0 {
+	pinctrl-0 = <&gpiohs_pinctrl>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&gpio1 {
+	pinctrl-0 = <&gpio_pinctrl>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&i2s0 {
+	#sound-dai-cells = <1>;
+	pinctrl-0 = <&i2s0_pinctrl>;
+	pinctrl-names = "default";
+};
+
+&i2c1 {
+	pinctrl-0 = <&i2c1_pinctrl>;
+	pinctrl-names = "default";
+	clock-frequency = <400000>;
+	status = "okay";
+};
+
+&dvp0 {
+	pinctrl-0 = <&dvp_pinctrl>;
+	pinctrl-names = "default";
+};
+
+&spi0 {
+	pinctrl-0 = <&spi0_pinctrl>;
+	pinctrl-names = "default";
+	num-cs = <1>;
+	cs-gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+
+	panel@0 {
+		compatible = "sitronix,st7789v";
+		reg = <0>;
+		reset-gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
+		dc-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
+		spi-max-frequency = <15000000>;
+		spi-cs-high;
+		status = "disabled";
+	};
+};
+
+&spi1 {
+	pinctrl-0 = <&spi1_pinctrl>;
+	pinctrl-names = "default";
+	num-cs = <1>;
+	cs-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	slot@0 {
+		compatible = "mmc-spi-slot";
+		reg = <0>;
+		voltage-ranges = <3300 3300>;
+		spi-max-frequency = <25000000>;
+		broken-cd;
+	};
+};
+
+&spi3 {
+	spi-flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+		m25p,fast-read;
+		broken-flash-reset;
+	};
+};
-- 
2.29.2

[PATCH v12 12/17] riscv: Add SiPeed MAIX DOCK board device tree

[Damien Le Moal]

Add the device tree sipeed_maix_dock.dts for the SiPeed MAIX DOCK m1
and m1w boards. This device tree enables LEDs, gpio, i2c and spi/mmc
SD card devices.

Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
---
 .../boot/dts/canaan/sipeed_maix_dock.dts      | 236 ++++++++++++++++++
 1 file changed, 236 insertions(+)
 create mode 100644 arch/riscv/boot/dts/canaan/sipeed_maix_dock.dts

diff --git a/arch/riscv/boot/dts/canaan/sipeed_maix_dock.dts b/arch/riscv/boot/dts/canaan/sipeed_maix_dock.dts
new file mode 100644
index 000000000000..fae0149a8740
--- /dev/null
+++ b/arch/riscv/boot/dts/canaan/sipeed_maix_dock.dts
@@ -0,0 +1,236 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2019-20 Sean Anderson <seanga2@gmail.com>
+ * Copyright (C) 2020 Western Digital Corporation or its affiliates.
+ */
+
+/dts-v1/;
+
+#include "k210.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "SiPeed MAIX Dock";
+	compatible = "sipeed,maix-dock-m1", "sipeed,maix-dock-m1w",
+		     "canaan,kendryte-k210";
+
+	chosen {
+		bootargs = "earlycon console=ttySIF0";
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		/*
+		 * Note: the board wiring drawing documents green on
+		 * gpio #4, red on gpio #5 and blue on gpio #6. However,
+		 * the board is actually wired differently as defined here.
+		 */
+		led0 {
+			color = <LED_COLOR_ID_BLUE>;
+			label = "blue";
+			gpios = <&gpio1_0 4 GPIO_ACTIVE_LOW>;
+		};
+
+		led1 {
+			color = <LED_COLOR_ID_GREEN>;
+			label = "green";
+			gpios = <&gpio1_0 5 GPIO_ACTIVE_LOW>;
+		};
+
+		led2 {
+			color = <LED_COLOR_ID_RED>;
+			label = "red";
+			gpios = <&gpio1_0 6 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		boot {
+			label = "BOOT";
+			linux,code = <BTN_0>;
+			gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		status = "disabled";
+
+		simple-audio-card,cpu {
+			sound-dai = <&i2s0 0>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&mic>;
+		};
+	};
+
+	mic: mic {
+		#sound-dai-cells = <0>;
+		compatible = "memsensing,msm261s4030h0";
+		status = "disabled";
+	};
+};
+
+&fpioa {
+	pinctrl-0 = <&jtag_pinctrl>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	jtag_pinctrl: jtag-pinmux {
+		pinmux = <K210_FPIOA(0, K210_PCF_JTAG_TCLK)>,
+			 <K210_FPIOA(1, K210_PCF_JTAG_TDI)>,
+			 <K210_FPIOA(2, K210_PCF_JTAG_TMS)>,
+			 <K210_FPIOA(3, K210_PCF_JTAG_TDO)>;
+	};
+
+	uarths_pinctrl: uarths-pinmux {
+		pinmux = <K210_FPIOA(4, K210_PCF_UARTHS_RX)>,
+			 <K210_FPIOA(5, K210_PCF_UARTHS_TX)>;
+	};
+
+	gpio_pinctrl: gpio-pinmux {
+		pinmux = <K210_FPIOA(8, K210_PCF_GPIO0)>,
+			 <K210_FPIOA(11, K210_PCF_GPIO3)>,
+			 <K210_FPIOA(12, K210_PCF_GPIO4)>,
+			 <K210_FPIOA(13, K210_PCF_GPIO5)>,
+			 <K210_FPIOA(14, K210_PCF_GPIO6)>,
+			 <K210_FPIOA(15, K210_PCF_GPIO7)>;
+	};
+
+	gpiohs_pinctrl: gpiohs-pinmux {
+		pinmux = <K210_FPIOA(16, K210_PCF_GPIOHS0)>,
+			 <K210_FPIOA(17, K210_PCF_GPIOHS1)>,
+			 <K210_FPIOA(21, K210_PCF_GPIOHS5)>,
+			 <K210_FPIOA(22, K210_PCF_GPIOHS6)>,
+			 <K210_FPIOA(23, K210_PCF_GPIOHS7)>,
+			 <K210_FPIOA(24, K210_PCF_GPIOHS8)>,
+			 <K210_FPIOA(25, K210_PCF_GPIOHS9)>,
+			 <K210_FPIOA(32, K210_PCF_GPIOHS16)>,
+			 <K210_FPIOA(33, K210_PCF_GPIOHS17)>,
+			 <K210_FPIOA(34, K210_PCF_GPIOHS18)>,
+			 <K210_FPIOA(35, K210_PCF_GPIOHS19)>;
+	};
+
+	i2s0_pinctrl: i2s0-pinmux {
+		pinmux = <K210_FPIOA(18, K210_PCF_I2S0_SCLK)>,
+			 <K210_FPIOA(19, K210_PCF_I2S0_WS)>,
+			 <K210_FPIOA(20, K210_PCF_I2S0_IN_D0)>;
+	};
+
+	dvp_pinctrl: dvp-pinmux {
+		pinmux = <K210_FPIOA(40, K210_PCF_SCCB_SDA)>,
+			 <K210_FPIOA(41, K210_PCF_SCCB_SCLK)>,
+			 <K210_FPIOA(42, K210_PCF_DVP_RST)>,
+			 <K210_FPIOA(43, K210_PCF_DVP_VSYNC)>,
+			 <K210_FPIOA(44, K210_PCF_DVP_PWDN)>,
+			 <K210_FPIOA(45, K210_PCF_DVP_HSYNC)>,
+			 <K210_FPIOA(46, K210_PCF_DVP_XCLK)>,
+			 <K210_FPIOA(47, K210_PCF_DVP_PCLK)>;
+	};
+
+	spi0_pinctrl: spi0-pinmux {
+		pinmux = <K210_FPIOA(36, K210_PCF_GPIOHS20)>,  /* cs */
+			 <K210_FPIOA(37, K210_PCF_GPIOHS21)>,  /* rst */
+			 <K210_FPIOA(38, K210_PCF_GPIOHS22)>,  /* dc */
+			 <K210_FPIOA(39, K210_PCF_SPI0_SCLK)>; /* wr */
+	};
+
+	spi1_pinctrl: spi1-pinmux {
+		pinmux = <K210_FPIOA(26, K210_PCF_SPI1_D1)>,
+			 <K210_FPIOA(27, K210_PCF_SPI1_SCLK)>,
+			 <K210_FPIOA(28, K210_PCF_SPI1_D0)>,
+			 <K210_FPIOA(29, K210_PCF_GPIOHS13)>; /* cs */
+	};
+
+	i2c1_pinctrl: i2c1-pinmux {
+		pinmux = <K210_FPIOA(9, K210_PCF_I2C1_SCLK)>,
+			 <K210_FPIOA(10, K210_PCF_I2C1_SDA)>;
+	};
+};
+
+&uarths0 {
+	pinctrl-0 = <&uarths_pinctrl>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&gpio0 {
+	pinctrl-0 = <&gpiohs_pinctrl>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&gpio1 {
+	pinctrl-0 = <&gpio_pinctrl>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&i2s0 {
+	#sound-dai-cells = <1>;
+	pinctrl-0 = <&i2s0_pinctrl>;
+	pinctrl-names = "default";
+};
+
+&i2c1 {
+	pinctrl-0 = <&i2c1_pinctrl>;
+	pinctrl-names = "default";
+	clock-frequency = <400000>;
+	status = "okay";
+};
+
+&dvp0 {
+	pinctrl-0 = <&dvp_pinctrl>;
+	pinctrl-names = "default";
+};
+
+&spi0 {
+	pinctrl-0 = <&spi0_pinctrl>;
+	pinctrl-names = "default";
+	num-cs = <1>;
+	cs-gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+
+	panel@0 {
+		compatible = "sitronix,st7789v";
+		reg = <0>;
+		reset-gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
+		dc-gpios = <&gpio0 22 0>;
+		spi-max-frequency = <15000000>;
+		status = "disabled";
+	};
+};
+
+&spi1 {
+	pinctrl-0 = <&spi1_pinctrl>;
+	pinctrl-names = "default";
+	num-cs = <1>;
+	cs-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	slot@0 {
+		compatible = "mmc-spi-slot";
+		reg = <0>;
+		voltage-ranges = <3300 3300>;
+		spi-max-frequency = <25000000>;
+		broken-cd;
+	};
+};
+
+&spi3 {
+	spi-flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+		m25p,fast-read;
+		broken-flash-reset;
+	};
+};
-- 
2.29.2

[PATCH v12 13/17] riscv: Add SiPeed MAIX GO board device tree

[Damien Le Moal]

Add the device tree sipeed_maix_go.dts for the SiPeed MAIX GO board.
This device tree enables buttons, LEDs, gpio, i2c and spi/mmc SD card
devices.

Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
---
 arch/riscv/boot/dts/canaan/sipeed_maix_go.dts | 244 ++++++++++++++++++
 1 file changed, 244 insertions(+)
 create mode 100644 arch/riscv/boot/dts/canaan/sipeed_maix_go.dts

diff --git a/arch/riscv/boot/dts/canaan/sipeed_maix_go.dts b/arch/riscv/boot/dts/canaan/sipeed_maix_go.dts
new file mode 100644
index 000000000000..373fbaa3ab94
--- /dev/null
+++ b/arch/riscv/boot/dts/canaan/sipeed_maix_go.dts
@@ -0,0 +1,244 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2019-20 Sean Anderson <seanga2@gmail.com>
+ * Copyright (C) 2020 Western Digital Corporation or its affiliates.
+ */
+
+/dts-v1/;
+
+#include "k210.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "SiPeed MAIX GO";
+	compatible = "sipeed,maix-go", "canaan,kendryte-k210";
+
+	chosen {
+		bootargs = "earlycon console=ttySIF0";
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		led0 {
+			color = <LED_COLOR_ID_GREEN>;
+			label = "green";
+			gpios = <&gpio1_0 4 GPIO_ACTIVE_LOW>;
+		};
+
+		led1 {
+			color = <LED_COLOR_ID_RED>;
+			label = "red";
+			gpios = <&gpio1_0 5 GPIO_ACTIVE_LOW>;
+		};
+
+		led2 {
+			color = <LED_COLOR_ID_BLUE>;
+			label = "blue";
+			gpios = <&gpio1_0 6 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		up {
+			label = "UP";
+			linux,code = <BTN_1>;
+			gpios = <&gpio1_0 7 GPIO_ACTIVE_LOW>;
+		};
+
+		press {
+			label = "PRESS";
+			linux,code = <BTN_0>;
+			gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
+		};
+
+		down {
+			label = "DOWN";
+			linux,code = <BTN_2>;
+			gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		status = "disabled";
+
+		simple-audio-card,cpu {
+			sound-dai = <&i2s0 0>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&mic>;
+		};
+	};
+
+	mic: mic {
+		#sound-dai-cells = <0>;
+		compatible = "memsensing,msm261s4030h0";
+		status = "disabled";
+	};
+};
+
+&fpioa {
+	pinctrl-0 = <&jtag_pinctrl>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	jtag_pinctrl: jtag-pinmux {
+		pinmux = <K210_FPIOA(0, K210_PCF_JTAG_TCLK)>,
+			 <K210_FPIOA(1, K210_PCF_JTAG_TDI)>,
+			 <K210_FPIOA(2, K210_PCF_JTAG_TMS)>,
+			 <K210_FPIOA(3, K210_PCF_JTAG_TDO)>;
+	};
+
+	uarths_pinctrl: uarths-pinmux {
+		pinmux = <K210_FPIOA(4, K210_PCF_UARTHS_RX)>,
+			 <K210_FPIOA(5, K210_PCF_UARTHS_TX)>;
+	};
+
+	gpio_pinctrl: gpio-pinmux {
+		pinmux = <K210_FPIOA(8, K210_PCF_GPIO0)>,
+			 <K210_FPIOA(9, K210_PCF_GPIO1)>,
+			 <K210_FPIOA(10, K210_PCF_GPIO2)>,
+			 <K210_FPIOA(11, K210_PCF_GPIO3)>,
+			 <K210_FPIOA(12, K210_PCF_GPIO4)>,
+			 <K210_FPIOA(13, K210_PCF_GPIO5)>,
+			 <K210_FPIOA(14, K210_PCF_GPIO6)>,
+			 <K210_FPIOA(15, K210_PCF_GPIO7)>;
+	};
+
+	gpiohs_pinctrl: gpiohs-pinmux {
+		pinmux = <K210_FPIOA(16, K210_PCF_GPIOHS0)>,
+			 <K210_FPIOA(17, K210_PCF_GPIOHS1)>,
+			 <K210_FPIOA(21, K210_PCF_GPIOHS5)>,
+			 <K210_FPIOA(22, K210_PCF_GPIOHS6)>,
+			 <K210_FPIOA(23, K210_PCF_GPIOHS7)>,
+			 <K210_FPIOA(24, K210_PCF_GPIOHS8)>,
+			 <K210_FPIOA(25, K210_PCF_GPIOHS9)>,
+			 <K210_FPIOA(32, K210_PCF_GPIOHS16)>,
+			 <K210_FPIOA(33, K210_PCF_GPIOHS17)>,
+			 <K210_FPIOA(34, K210_PCF_GPIOHS18)>,
+			 <K210_FPIOA(35, K210_PCF_GPIOHS19)>;
+	};
+
+	i2s0_pinctrl: i2s0-pinmux {
+		pinmux = <K210_FPIOA(18, K210_PCF_I2S0_SCLK)>,
+			 <K210_FPIOA(19, K210_PCF_I2S0_WS)>,
+			 <K210_FPIOA(20, K210_PCF_I2S0_IN_D0)>;
+	};
+
+	dvp_pinctrl: dvp-pinmux {
+		pinmux = <K210_FPIOA(40, K210_PCF_SCCB_SDA)>,
+			 <K210_FPIOA(41, K210_PCF_SCCB_SCLK)>,
+			 <K210_FPIOA(42, K210_PCF_DVP_RST)>,
+			 <K210_FPIOA(43, K210_PCF_DVP_VSYNC)>,
+			 <K210_FPIOA(44, K210_PCF_DVP_PWDN)>,
+			 <K210_FPIOA(45, K210_PCF_DVP_HSYNC)>,
+			 <K210_FPIOA(46, K210_PCF_DVP_XCLK)>,
+			 <K210_FPIOA(47, K210_PCF_DVP_PCLK)>;
+	};
+
+	spi0_pinctrl: spi0-pinmux {
+		pinmux = <K210_FPIOA(36, K210_PCF_GPIOHS20)>,  /* cs */
+			 <K210_FPIOA(37, K210_PCF_GPIOHS21)>,  /* rst */
+			 <K210_FPIOA(38, K210_PCF_GPIOHS22)>,  /* dc */
+			 <K210_FPIOA(39, K210_PCF_SPI0_SCLK)>; /* wr */
+	};
+
+	spi1_pinctrl: spi1-pinmux {
+		pinmux = <K210_FPIOA(26, K210_PCF_SPI1_D1)>,
+			 <K210_FPIOA(27, K210_PCF_SPI1_SCLK)>,
+			 <K210_FPIOA(28, K210_PCF_SPI1_D0)>,
+			 <K210_FPIOA(29, K210_PCF_GPIOHS13)>; /* cs */
+	};
+
+	i2c1_pinctrl: i2c1-pinmux {
+		pinmux = <K210_FPIOA(30, K210_PCF_I2C1_SCLK)>,
+			 <K210_FPIOA(31, K210_PCF_I2C1_SDA)>;
+	};
+};
+
+&uarths0 {
+	pinctrl-0 = <&uarths_pinctrl>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&gpio0 {
+	pinctrl-0 = <&gpiohs_pinctrl>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&gpio1 {
+	pinctrl-0 = <&gpio_pinctrl>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&i2s0 {
+	#sound-dai-cells = <1>;
+	pinctrl-0 = <&i2s0_pinctrl>;
+	pinctrl-names = "default";
+};
+
+&i2c1 {
+	pinctrl-0 = <&i2c1_pinctrl>;
+	pinctrl-names = "default";
+	clock-frequency = <400000>;
+	status = "okay";
+};
+
+&dvp0 {
+	pinctrl-0 = <&dvp_pinctrl>;
+	pinctrl-names = "default";
+};
+
+&spi0 {
+	pinctrl-0 = <&spi0_pinctrl>;
+	pinctrl-names = "default";
+	num-cs = <1>;
+	cs-gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+
+	panel@0 {
+		compatible = "sitronix,st7789v";
+		reg = <0>;
+		reset-gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
+		dc-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
+		spi-max-frequency = <15000000>;
+		status = "disabled";
+	};
+};
+
+&spi1 {
+	pinctrl-0 = <&spi1_pinctrl>;
+	pinctrl-names = "default";
+	num-cs = <1>;
+	cs-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	slot@0 {
+		compatible = "mmc-spi-slot";
+		reg = <0>;
+		voltage-ranges = <3300 3300>;
+		spi-max-frequency = <25000000>;
+		broken-cd;
+	};
+};
+
+&spi3 {
+	spi-flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+		m25p,fast-read;
+		broken-flash-reset;
+	};
+};
-- 
2.29.2

[PATCH v12 14/17] riscv: Add SiPeed MAIXDUINO board device tree

[Damien Le Moal]

Add the device tree sipeed_maixduino.dts for the SiPeed MAIXDUINO board.
This device tree enables LEDs and spi/mmc SD card device. Additionally,
gpios and i2c are also enabled and mapped to the board header pins as
indicated on the board itself.

Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
---
 .../boot/dts/canaan/sipeed_maixduino.dts      | 209 ++++++++++++++++++
 1 file changed, 209 insertions(+)
 create mode 100644 arch/riscv/boot/dts/canaan/sipeed_maixduino.dts

diff --git a/arch/riscv/boot/dts/canaan/sipeed_maixduino.dts b/arch/riscv/boot/dts/canaan/sipeed_maixduino.dts
new file mode 100644
index 000000000000..804edc45eeeb
--- /dev/null
+++ b/arch/riscv/boot/dts/canaan/sipeed_maixduino.dts
@@ -0,0 +1,209 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2019-20 Sean Anderson <seanga2@gmail.com>
+ * Copyright (C) 2020 Western Digital Corporation or its affiliates.
+ */
+
+/dts-v1/;
+
+#include "k210.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "SiPeed MAIXDUINO";
+	compatible = "sipeed,maixduino", "canaan,kendryte-k210";
+
+	chosen {
+		bootargs = "earlycon console=ttySIF0";
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		boot {
+			label = "BOOT";
+			linux,code = <BTN_0>;
+			gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		status = "disabled";
+
+		simple-audio-card,cpu {
+			sound-dai = <&i2s0 0>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&mic>;
+		};
+	};
+
+	mic: mic {
+		#sound-dai-cells = <0>;
+		compatible = "memsensing,msm261s4030h0";
+		status = "disabled";
+	};
+
+	vcc_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&fpioa {
+	status = "okay";
+
+	uarths_pinctrl: uarths-pinmux {
+		pinmux = <K210_FPIOA(4, K210_PCF_UARTHS_RX)>, /* Header "0" */
+			 <K210_FPIOA(5, K210_PCF_UARTHS_TX)>; /* Header "1" */
+	};
+
+	gpio_pinctrl: gpio-pinmux {
+		pinmux = <K210_FPIOA(8, K210_PCF_GPIO0)>,
+			 <K210_FPIOA(9, K210_PCF_GPIO1)>;
+	};
+
+	gpiohs_pinctrl: gpiohs-pinmux {
+		pinmux = <K210_FPIOA(16, K210_PCF_GPIOHS0)>,  /* BOOT */
+			 <K210_FPIOA(21, K210_PCF_GPIOHS2)>,  /* Header "2" */
+			 <K210_FPIOA(22, K210_PCF_GPIOHS3)>,  /* Header "3" */
+			 <K210_FPIOA(23, K210_PCF_GPIOHS4)>,  /* Header "4" */
+			 <K210_FPIOA(24, K210_PCF_GPIOHS5)>,  /* Header "5" */
+			 <K210_FPIOA(32, K210_PCF_GPIOHS6)>,  /* Header "6" */
+			 <K210_FPIOA(15, K210_PCF_GPIOHS7)>,  /* Header "7" */
+			 <K210_FPIOA(14, K210_PCF_GPIOHS8)>,  /* Header "8" */
+			 <K210_FPIOA(13, K210_PCF_GPIOHS9)>,  /* Header "9" */
+			 <K210_FPIOA(12, K210_PCF_GPIOHS10)>, /* Header "10" */
+			 <K210_FPIOA(11, K210_PCF_GPIOHS11)>, /* Header "11" */
+			 <K210_FPIOA(10, K210_PCF_GPIOHS12)>, /* Header "12" */
+			 <K210_FPIOA(3,  K210_PCF_GPIOHS13)>; /* Header "13" */
+	};
+
+	i2s0_pinctrl: i2s0-pinmux {
+		pinmux = <K210_FPIOA(18, K210_PCF_I2S0_SCLK)>,
+			 <K210_FPIOA(19, K210_PCF_I2S0_WS)>,
+			 <K210_FPIOA(20, K210_PCF_I2S0_IN_D0)>;
+	};
+
+	spi1_pinctrl: spi1-pinmux {
+		pinmux = <K210_FPIOA(26, K210_PCF_SPI1_D1)>,
+			 <K210_FPIOA(27, K210_PCF_SPI1_SCLK)>,
+			 <K210_FPIOA(28, K210_PCF_SPI1_D0)>,
+			 <K210_FPIOA(29, K210_PCF_GPIO2)>; /* cs */
+	};
+
+	i2c1_pinctrl: i2c1-pinmux {
+		pinmux = <K210_FPIOA(30, K210_PCF_I2C1_SCLK)>, /* Header "scl" */
+			 <K210_FPIOA(31, K210_PCF_I2C1_SDA)>;  /* Header "sda" */
+	};
+
+	i2s1_pinctrl: i2s1-pinmux {
+		pinmux = <K210_FPIOA(33, K210_PCF_I2S1_WS)>,
+			 <K210_FPIOA(34, K210_PCF_I2S1_IN_D0)>,
+			 <K210_FPIOA(35, K210_PCF_I2S1_SCLK)>;
+	};
+
+	spi0_pinctrl: spi0-pinmux {
+		pinmux = <K210_FPIOA(36, K210_PCF_GPIOHS20)>,  /* cs */
+			 <K210_FPIOA(37, K210_PCF_GPIOHS21)>,  /* rst */
+			 <K210_FPIOA(38, K210_PCF_GPIOHS22)>,  /* dc */
+			 <K210_FPIOA(39, K210_PCF_SPI0_SCLK)>; /* wr */
+	};
+
+	dvp_pinctrl: dvp-pinmux {
+		pinmux = <K210_FPIOA(40, K210_PCF_SCCB_SDA)>,
+			 <K210_FPIOA(41, K210_PCF_SCCB_SCLK)>,
+			 <K210_FPIOA(42, K210_PCF_DVP_RST)>,
+			 <K210_FPIOA(43, K210_PCF_DVP_VSYNC)>,
+			 <K210_FPIOA(44, K210_PCF_DVP_PWDN)>,
+			 <K210_FPIOA(45, K210_PCF_DVP_HSYNC)>,
+			 <K210_FPIOA(46, K210_PCF_DVP_XCLK)>,
+			 <K210_FPIOA(47, K210_PCF_DVP_PCLK)>;
+	};
+};
+
+&uarths0 {
+	pinctrl-0 = <&uarths_pinctrl>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&gpio0 {
+	pinctrl-0 = <&gpiohs_pinctrl>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&gpio1 {
+	pinctrl-0 = <&gpio_pinctrl>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&i2s0 {
+	#sound-dai-cells = <1>;
+	pinctrl-0 = <&i2s0_pinctrl>;
+	pinctrl-names = "default";
+};
+
+&i2c1 {
+	pinctrl-0 = <&i2c1_pinctrl>;
+	pinctrl-names = "default";
+	clock-frequency = <400000>;
+	status = "okay";
+};
+
+&dvp0 {
+	pinctrl-0 = <&dvp_pinctrl>;
+	pinctrl-names = "default";
+};
+
+&spi0 {
+	pinctrl-0 = <&spi0_pinctrl>;
+	pinctrl-names = "default";
+	num-cs = <1>;
+	cs-gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+
+	panel@0 {
+		compatible = "sitronix,st7789v";
+		reg = <0>;
+		reset-gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
+		dc-gpios = <&gpio0 22 0>;
+		spi-max-frequency = <15000000>;
+		power-supply = <&vcc_3v3>;
+	};
+};
+
+&spi1 {
+	pinctrl-0 = <&spi1_pinctrl>;
+	pinctrl-names = "default";
+	num-cs = <1>;
+	cs-gpios = <&gpio1_0 2 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	slot@0 {
+		compatible = "mmc-spi-slot";
+		reg = <0>;
+		voltage-ranges = <3300 3300>;
+		spi-max-frequency = <25000000>;
+		broken-cd;
+	};
+};
+
+&spi3 {
+	spi-flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+		m25p,fast-read;
+		broken-flash-reset;
+	};
+};
-- 
2.29.2

[PATCH v12 15/17] riscv: Add Kendryte KD233 board device tree

[Damien Le Moal]

Add the device tree canaan_kd233.dts for the Canaan Kendryte KD233
development board.  This device tree enables LEDs, some gpios and
spi/mmc SD card device. The WS2812B RGB LED and the 10 positions rotary
dip switch present on the board are left undefined.

Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
---
 arch/riscv/boot/dts/canaan/canaan_kd233.dts | 177 ++++++++++++++++++++
 1 file changed, 177 insertions(+)
 create mode 100644 arch/riscv/boot/dts/canaan/canaan_kd233.dts

diff --git a/arch/riscv/boot/dts/canaan/canaan_kd233.dts b/arch/riscv/boot/dts/canaan/canaan_kd233.dts
new file mode 100644
index 000000000000..d9af66144938
--- /dev/null
+++ b/arch/riscv/boot/dts/canaan/canaan_kd233.dts
@@ -0,0 +1,177 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2019-20 Sean Anderson <seanga2@gmail.com>
+ * Copyright (C) 2020 Western Digital Corporation or its affiliates.
+ */
+
+/dts-v1/;
+
+#include "k210.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Kendryte KD233";
+	compatible = "canaan,kendryte-kd233", "canaan,kendryte-k210";
+
+	chosen {
+		bootargs = "earlycon console=ttySIF0";
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		led0 {
+			gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
+		};
+
+		led1 {
+			gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key0 {
+			label = "KEY0";
+			linux,code = <BTN_0>;
+			gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		status = "disabled";
+
+		simple-audio-card,cpu {
+			sound-dai = <&i2s0 0>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&mic>;
+		};
+	};
+
+	mic: mic {
+		#sound-dai-cells = <0>;
+		compatible = "memsensing,msm261s4030h0";
+		status = "disabled";
+	};
+};
+
+&fpioa {
+	pinctrl-0 = <&jtag_pinctrl>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	jtag_pinctrl: jtag-pinmux {
+		pinmux = <K210_FPIOA(0, K210_PCF_JTAG_TCLK)>,
+			 <K210_FPIOA(1, K210_PCF_JTAG_TDI)>,
+			 <K210_FPIOA(2, K210_PCF_JTAG_TMS)>,
+			 <K210_FPIOA(3, K210_PCF_JTAG_TDO)>;
+	};
+
+	uarths_pinctrl: uarths-pinmux {
+		pinmux = <K210_FPIOA(4, K210_PCF_UARTHS_RX)>,
+			 <K210_FPIOA(5, K210_PCF_UARTHS_TX)>;
+	};
+
+	spi0_pinctrl: spi0-pinmux {
+		pinmux = <K210_FPIOA(6, K210_PCF_GPIOHS20)>,  /* cs */
+			 <K210_FPIOA(7, K210_PCF_SPI0_SCLK)>, /* wr */
+			 <K210_FPIOA(8, K210_PCF_GPIOHS21)>;  /* dc */
+	};
+
+	dvp_pinctrl: dvp-pinmux {
+		pinmux = <K210_FPIOA(9, K210_PCF_SCCB_SCLK)>,
+			 <K210_FPIOA(10, K210_PCF_SCCB_SDA)>,
+			 <K210_FPIOA(11, K210_PCF_DVP_RST)>,
+			 <K210_FPIOA(12, K210_PCF_DVP_VSYNC)>,
+			 <K210_FPIOA(13, K210_PCF_DVP_PWDN)>,
+			 <K210_FPIOA(14, K210_PCF_DVP_XCLK)>,
+			 <K210_FPIOA(15, K210_PCF_DVP_PCLK)>,
+			 <K210_FPIOA(17, K210_PCF_DVP_HSYNC)>;
+	};
+
+	gpiohs_pinctrl: gpiohs-pinmux {
+		pinmux = <K210_FPIOA(16, K210_PCF_GPIOHS0)>,
+			 <K210_FPIOA(20, K210_PCF_GPIOHS4)>, /* Rot. dip sw line 8 */
+			 <K210_FPIOA(21, K210_PCF_GPIOHS5)>, /* Rot. dip sw line 4 */
+			 <K210_FPIOA(22, K210_PCF_GPIOHS6)>, /* Rot. dip sw line 2 */
+			 <K210_FPIOA(23, K210_PCF_GPIOHS7)>, /* Rot. dip sw line 1 */
+			 <K210_FPIOA(24, K210_PCF_GPIOHS8)>,
+			 <K210_FPIOA(25, K210_PCF_GPIOHS9)>,
+			 <K210_FPIOA(26, K210_PCF_GPIOHS10)>;
+	};
+
+	spi1_pinctrl: spi1-pinmux {
+		pinmux = <K210_FPIOA(29, K210_PCF_SPI1_SCLK)>,
+			 <K210_FPIOA(30, K210_PCF_SPI1_D0)>,
+			 <K210_FPIOA(31, K210_PCF_SPI1_D1)>,
+			 <K210_FPIOA(32, K210_PCF_GPIOHS16)>; /* cs */
+	};
+
+	i2s0_pinctrl: i2s0-pinmux {
+		pinmux = <K210_FPIOA(33, K210_PCF_I2S0_IN_D0)>,
+			 <K210_FPIOA(34, K210_PCF_I2S0_WS)>,
+			 <K210_FPIOA(35, K210_PCF_I2S0_SCLK)>;
+	};
+};
+
+&uarths0 {
+	pinctrl-0 = <&uarths_pinctrl>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&gpio0 {
+	pinctrl-0 = <&gpiohs_pinctrl>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&i2s0 {
+	#sound-dai-cells = <1>;
+	pinctrl-0 = <&i2s0_pinctrl>;
+	pinctrl-names = "default";
+};
+
+&dvp0 {
+	pinctrl-0 = <&dvp_pinctrl>;
+	pinctrl-names = "default";
+};
+
+&spi0 {
+	pinctrl-0 = <&spi0_pinctrl>;
+	pinctrl-names = "default";
+	num-cs = <1>;
+	cs-gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+
+	panel@0 {
+		compatible = "ilitek,ili9341";
+		reg = <0>;
+		dc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>;
+		spi-max-frequency = <15000000>;
+		status = "disabled";
+	};
+};
+
+&spi1 {
+	pinctrl-0 = <&spi1_pinctrl>;
+	pinctrl-names = "default";
+	num-cs = <1>;
+	cs-gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	slot@0 {
+		compatible = "mmc-spi-slot";
+		reg = <0>;
+		voltage-ranges = <3300 3300>;
+		spi-max-frequency = <25000000>;
+		broken-cd;
+	};
+};
-- 
2.29.2