[PATCH 1/2 v2] Bluetooth: btbcm: Rewrite bindings in YAML and add reset

[PATCH 1/2 v2] Bluetooth: btbcm: Rewrite bindings in YAML and add reset

[Linus Walleij]

This rewrites the Broadcom bluetooth bindings in YAML and
adds a GPIO handle for the BT_RST_N line as used on some
platforms.

The Ingenic UART binding was using this binding in its
example DTS fragment, however mistakenly using "vcc-supply"
for what is called "vbat-supply". The proper DTS files
and the code in the kernel all use "vbat-supply" so
fix up the example in this patch so we ge a clean
check.

Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
ChangeLog v1->v2:
- Fix the error in the Ingenic UART binding example as
  part of adding this patch.
---
 .../bindings/net/broadcom-bluetooth.txt       |  56 ---------
 .../bindings/net/broadcom-bluetooth.yaml      | 117 ++++++++++++++++++
 2 files changed, 117 insertions(+), 56 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
 create mode 100644 Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml

diff --git a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
deleted file mode 100644
index a7d57ba5f2ac..000000000000
--- a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
+++ /dev/null
@@ -1,56 +0,0 @@
-Broadcom Bluetooth Chips
----------------------
-
-This documents the binding structure and common properties for serial
-attached Broadcom devices.
-
-Serial attached Broadcom devices shall be a child node of the host UART
-device the slave device is attached to.
-
-Required properties:
-
- - compatible: should contain one of the following:
-   * "brcm,bcm20702a1"
-   * "brcm,bcm4329-bt"
-   * "brcm,bcm4330-bt"
-   * "brcm,bcm43438-bt"
-   * "brcm,bcm4345c5"
-   * "brcm,bcm43540-bt"
-   * "brcm,bcm4335a0"
-
-Optional properties:
-
- - max-speed: see Documentation/devicetree/bindings/serial/serial.yaml
- - shutdown-gpios: GPIO specifier, used to enable the BT module
- - device-wakeup-gpios: GPIO specifier, used to wakeup the controller
- - host-wakeup-gpios: GPIO specifier, used to wakeup the host processor.
-                      deprecated, replaced by interrupts and
-                      "host-wakeup" interrupt-names
- - clocks: 1 or 2 clocks as defined in clock-names below, in that order
- - clock-names: names for clock inputs, matching the clocks given
-   - "extclk": deprecated, replaced by "txco"
-   - "txco": external reference clock (not a standalone crystal)
-   - "lpo": external low power 32.768 kHz clock
- - vbat-supply: phandle to regulator supply for VBAT
- - vddio-supply: phandle to regulator supply for VDDIO
- - brcm,bt-pcm-int-params: configure PCM parameters via a 5-byte array
-    - sco-routing: 0 = PCM, 1 = Transport, 2 = Codec, 3 = I2S
-    - pcm-interface-rate: 128KBps, 256KBps, 512KBps, 1024KBps, 2048KBps
-    - pcm-frame-type: short, long
-    - pcm-sync-mode: slave, master
-    - pcm-clock-mode: slave, master
- - interrupts: must be one, used to wakeup the host processor
- - interrupt-names: must be "host-wakeup"
-
-Example:
-
-&uart2 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&uart2_pins>;
-
-       bluetooth {
-               compatible = "brcm,bcm43438-bt";
-               max-speed = <921600>;
-               brcm,bt-pcm-int-params = [01 02 00 01 01];
-       };
-};
diff --git a/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml b/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml
new file mode 100644
index 000000000000..bdd6ca617e23
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml
@@ -0,0 +1,117 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/broadcom-bluetooth.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom Bluetooth Chips
+
+maintainers:
+  - Linus Walleij <linus.walleij@linaro.org>
+
+description:
+  This binding describes Broadcom UART-attached bluetooth chips.
+
+properties:
+  compatible:
+    enum:
+      - brcm,bcm20702a1
+      - brcm,bcm4329-bt
+      - brcm,bcm4330-bt
+      - brcm,bcm43438-bt
+      - brcm,bcm4345c5
+      - brcm,bcm43540-bt
+      - brcm,bcm4335a0
+
+  shutdown-gpios:
+    maxItems: 1
+    description: GPIO specifier for the line BT_REG_ON used to
+      power on the BT module
+
+  reset-gpios:
+    maxItems: 1
+    description: GPIO specifier for the line BT_RST_N used to
+      reset the BT module. This should be marked as
+      GPIO_ACTIVE_LOW.
+
+  device-wakeup-gpios:
+    maxItems: 1
+    description: GPIO specifier for the line BT_WAKE used to
+      wakeup the controller. This is using the BT_GPIO_0
+      pin on the chip when in use.
+
+  host-wakeup-gpios:
+    maxItems: 1
+    deprecated: true
+    description: GPIO specifier for the line HOST_WAKE used
+      to wakeup the host processor. This is using he BT_GPIO_1
+      pin on the chip when in use. This is deprecated and replaced
+      by interrupts and "host-wakeup" interrupt-names
+
+  clocks:
+    maxItems: 2
+    description: 1 or 2 clocks as defined in clock-names below,
+      in that order
+
+  clock-names:
+    description: Names of the 1 to 2 supplied clocks
+    items:
+      - const: txco
+      - const: lpo
+      - const: extclk
+
+  vbat-supply:
+    description: phandle to regulator supply for VBAT
+
+  vddio-supply:
+    description: phandle to regulator supply for VDDIO
+
+  brcm,bt-pcm-int-params:
+    $ref: /schemas/types.yaml#/definitions/uint8-array
+    minItems: 5
+    maxItems: 5
+    description: |-
+      configure PCM parameters via a 5-byte array:
+       sco-routing: 0 = PCM, 1 = Transport, 2 = Codec, 3 = I2S
+       pcm-interface-rate: 128KBps, 256KBps, 512KBps, 1024KBps, 2048KBps
+       pcm-frame-type: short, long
+       pcm-sync-mode: slave, master
+       pcm-clock-mode: slave, master
+
+  interrupts:
+    items:
+      - description: Handle to the line HOST_WAKE used to wake
+          up the host processor. This uses the BT_GPIO_1 pin on
+          the chip when in use.
+
+  interrupt-names:
+    items:
+      - const: host-wakeup
+
+  max-speed: true
+  current-speed: true
+
+required:
+  - compatible
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    uart {
+        uart-has-rtscts;
+
+        bluetooth {
+            compatible = "brcm,bcm4330-bt";
+            max-speed = <921600>;
+            brcm,bt-pcm-int-params = [01 02 00 01 01];
+            shutdown-gpios = <&gpio 30 GPIO_ACTIVE_HIGH>;
+            device-wakeup-gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
+            reset-gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
+            interrupt-parent = <&gpio>;
+            interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
+        };
+    };
-- 
2.29.2

Re: [PATCH 1/2 v2] Bluetooth: btbcm: Rewrite bindings in YAML and add reset

[Rob Herring]

On Fri, 05 Mar 2021 14:23:42 +0100, Linus Walleij wrote:
> This rewrites the Broadcom bluetooth bindings in YAML and
> adds a GPIO handle for the BT_RST_N line as used on some
> platforms.
> 
> The Ingenic UART binding was using this binding in its
> example DTS fragment, however mistakenly using "vcc-supply"
> for what is called "vbat-supply". The proper DTS files
> and the code in the kernel all use "vbat-supply" so
> fix up the example in this patch so we ge a clean
> check.
> 
> Cc: devicetree@vger.kernel.org
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> ---
> ChangeLog v1->v2:
> - Fix the error in the Ingenic UART binding example as
>   part of adding this patch.
> ---
>  .../bindings/net/broadcom-bluetooth.txt       |  56 ---------
>  .../bindings/net/broadcom-bluetooth.yaml      | 117 ++++++++++++++++++
>  2 files changed, 117 insertions(+), 56 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
>  create mode 100644 Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/serial/ingenic,uart.example.dt.yaml: bluetooth: 'vcc-supply' does not match any of the regexes: 'pinctrl-[0-9]+'
	From schema: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml

See https://patchwork.ozlabs.org/patch/1447828

This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit.